Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).     

Photovoltaic performance improvement of dye-sensitized solar cells based on tantalum-doped TiO2 thin films

Dye-sensitized solar cells based on a tantalum (Ta)-doped TiO₂ thin film prepared by the hydrothermal method show a photovoltaic efficiency of 8.18%, which is higher than that of the undoped TiO₂ thin film (7.40%). The Mott-Schottky plot indicates that the Ta-doped TiO₂ photoanode shifts the flat band potential positively and increases the electron density. The positive shift of the flat band potential improves the driving force of injected electrons from the LUMO of the dye to the conduction band of TiO₂. Furthermore, the increased electron density caused by the Ta-doped TiO₂ improves the fill factor of the solar cell. The increased electron density accelerates the transfer rate of electrons in the Ta-doped TiO₂ thin films by comparison to undoped films, which is confirmed by intensity-modulated photocurrent spectroscopy measurements.     

Photovoltaic efficiency on dye-sensitized solar cells (DSSC) assembled using Ga-incorporated TiO2 materials

This study examined the photoelectric conversion efficiency of DSSC (dye-sensitized solar cell) when nanometer sized Ga (0.25, 0.50, and 1.00 mol%)–TiO₂ prepared using a hydrothermal method was employed as a working electrode material. The particle sizes observed in the transmission electron microscopy images were <20 nm in all samples. However, with increasing Ga concentration, the size increased and the shapes transformed to a stick form. The absorption band was slightly blue-shifted upon the incorporation of gallium ions, but the intensity of the photoluminescence (PL) curves of the Ga-incorporated TiO₂ was significantly smaller, with the smallest case being the 0.50 mol% Ga–TiO_2, which was related to recombination between the excited electrons and holes. When Ga–TiO₂ was applied in DSSC, the energy conversion efficiency was enhanced considerably compared to that using pure TiO₂; it was approximately 4.57% with the N3 dye under 100 mW/cm² of simulated sunlight. These results are in agreement with an electrostatic force microscopy (EFM) study showing that the electrons were transferred rapidly to the surface of Ga–TiO₂ film, compared with that on a pure TiO₂ film.     

Dye-sensitized solar cells based on double-layered TiO2 composite films and enhanced photovoltaic performance

Dye-sensitized solar cells (DSSCs) are fabricated based on double-layered composite films of TiO₂ nanoparticles and hollow spheres. The photoelectric conversion performances of DSSCs based on nanoparticles/nanoparticles (PP), hollow spheres/hollow spheres (HH), hollow spheres/nanoparticles (HP), and nanoparticles/hollow spheres (PH) double-layered films are investigated, and their photo-electric conversion efficiencies are 4.33, 4.72, 4.93 and 5.28%, respectively. The enhanced performance of TiO₂ nanoparticles/hollow spheres double-layered composite film solar cells can be attributed to the combined effect of following factors. The light scattering of overlayer hollow spheres enhances harvesting light of the DSSCs and the underlayer TiO₂ nanoparticle layer ensures good electronic contact between film electrode and the F-doped tin oxide (FTO) glass substrate. Furthermore, the high surface areas and pore volume of TiO₂ hollow spheres are respectively beneficial to adsorption of dye molecules and transfer of electrolyte solution.     

Enhanced power conversion efficiency in dye-sensitized solar cells with TiO2 aggregates/nanocrystallites mixed photoelectrodes

Photoelectrodes of mixed microsized TiO₂ aggregates and individually dispersed TiO₂ nanocrystallites with different ratios were fabricated and studied for improved power conversion efficiency in dye-sensitized solar cells (DSCs). TiO₂ aggregates/nanocrystallites composites possess several advantages for high performance of DSCs, including the light scattering by the microsized TiO₂ aggregates and the high surface area of nanocrystallites both in aggregates and individually dispersed. A high power conversion efficiency of 7.59% was achieved with mixed TiO₂ aggregates/nanocrystallites photoelectrode using conventional dye N3, without applying anti-reflection coating, back-scattering layer, or chemical treatment. The electron transport properties of DSCs with mixed photoelectrodes were investigated by electrochemical impedance spectra, and the results showed that such a photoelectrode with mixed aggregates and nanocrystallites possess better connectivity for efficient electron transport.     

Conversion enhancement of flexible dye-sensitized solar cells based on TiO2 nanotube arrays with TiO2 nanoparticles by electrophoretic deposition

We prepared highly ordered titanium dioxide nanotube arrays (TNAs) by anodizing Ti foils in F⁻ containing electrolyte. The thickness and dye loading amount of TNAs were 26 μm and 1.06 × 10⁻⁷ mol cm⁻², respectively. TiO₂ nanoparticles (TNPs) were electrophoretically deposited on the inner wall of nanotube to produce coated nanotube arrays (TNAP). The dye loading was increased to 1.56 × 10⁻⁷ mol cm⁻², and the electron transport rate improved. TNAs and TNAP were sensitized with ruthenium dye N3 to yield dye-sensitized TiO₂ nanotube solar cells. The power conversion efficiency of TNA-based dye-sensitized solar cells (DSSCs) was 4.28%, whereas the efficiency of TNAP-based DSSCs increased to 6.28% when illuminated from the counter electrode. The increase of power conversion efficiency of TNAP-based DSSCs is ascribed to the increased surface area of TNAs and the faster electron transport rate.     

EIS analysis on low temperature fabrication of TiO2 porous films for dye-sensitized solar cells

A low temperature (<150 °C) fabrication method for preparation of TiO₂ porous films with high efficiency in dye-sensitized solar cells (DSSCs) has been developed. The Ti(IV) tetraisopropoxide (TTIP) was added to the paste of TiO₂ nanoparticles to interconnect the TiO₂ particles. The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance at the TiO₂/dye/electrolyte interface (R_ct2) and electron lifetime in the TiO₂ film (τ_e) under different molar ratios of TTIP/TiO₂ and also at various TiO₂ thicknesses. It was found that the R_ct2 decreased as the molar ratio increased from 0.02 to 0.08, however, it increased at a molar ratio of 0.2 due to the reduction in surface area for dye adsorption. In addition, the characteristic frequency peak shifted to lower frequency at a molar ratio of 0.08, indicating the longer electron lifetime. As for the thickness effect, TiO₂ film with a thickness around 17 μm achieved the best cell efficiency. EIS study also confirmed that, under illumination, the smallest R_ct2 was associated with a TiO₂ thickness of 17 μm, with the R_ct2 increased as the thickness of TiO₂ film increased. In the Bode plots, the characteristic frequency peaks shifted to higher frequency when the thickness of TiO₂ increased from 17.2 to 48.2 μm, indicating the electron recombination increases as the thickness of the TiO₂ electrode increases.Finally, to make better use of longer wavelength light, 30 wt% of larger TiO₂ particle (300 nm) was mixed with P25 TiO₂ as light scattering particles. It effectively increased the short-circuit current density and cell conversion efficiency from 7.44 to 8.80 mA cm⁻² and 3.75 to 4.20%, respectively.     

Stable TiO2 nanotube arrays with high UV photoconversion efficiency

This work is intended to define an optimal methodology for preparing highly ordered TiO₂ nanotube arrays by a 60-V anodization in a glycol ethylene solution. In order to obtain a mechanically stable structure with a high UV photoconversion efficiency, it is necessary to carefully control the growth mechanism through the anodization process. For this reason, the nanotube arrays have to be formed upon a compact titanium dioxide layer with well-defined thickness. Besides, both the fluoride concentration and anodization time are strictly correlated, because elevated concentrations and/or a long anodization time produce unstable structure with low photoconversion efficiency. The best result in the terms of reproducibility has been obtained previously for a three-minute galvanostatic oxide growth on the pickled titanium sheet, and anodic growth in ethylene glycol solution containing 1 wt.% H₂O and 0.20 wt.% NH₄F for a period lower than 4.5 h. The UV photoconversion efficiency was measured and a maximum value of 28.3% has been obtained, which is the highest result in the literature.     

Electrophoretic deposition of nanocrystalline TiO2 films on Ti substrates for use in flexible dye-sensitized solar cells

Nanocrystalline TiO₂ films were prepared on flexible Ti-metal sheets by electrophoretic deposition followed by chemical treatment with tetra-n-butyl titanate (TBT) and sintering at 450 °C. X-ray diffraction (XRD) analysis indicates that TBT treatment led to the formation of additional anatase TiO₂, which plays an important role in improving the interconnection between TiO₂ particles, as well as the adherence of the film to the substrate, and in modifying the surface properties of the nanocrystalline particles. The effect of TBT treatment on the electron transport in the nanocrystalline films was studied by intensity-modulated photocurrent spectroscopy (IMPS). An increase in the conversion efficiency was obtained for the dye-sensitized solar cells with TBT-treated nanocrystalline TiO₂ films. The cell performance was further optimized by designing nanocrystalline TiO₂ films with a double-layer structure composed of a light-scattering layer and a transparent layer. The light-scattering effect of the double-layer nanocrystalline films was evaluated by diffuse reflectance spectra. Employing the double-layer nanocrystalline films as the photoelectrodes resulted in a significant improvement in the incident photo-to-current conversion efficiency of the corresponding cells due to enhanced solar absorption by light scattering. A high conversion efficiency of 6.33% was measured under illumination with 100 mW cm⁻² (AM 1.5) simulated sunlight.     

Large-area TiO2 nanotube dye-sensitized solar cells using thermal-sprayed Ti layers on stainless steel

This work presents large-scale dye-sensitized solar cells and methods for their manufacture. A dye-sensitized solar cell device contains a photosensitive dye adsorbed on a large surface of the anode, and a transparent conductive cathode disposed opposite the anode, wherein platinum nano-catalytic particles adhere to its surface, and an electrolytic solution is sealed between the anode and the transparent conductive cathode. A titania nanotube film was fabricated by thermo-spraying titanium film on 304 stainless-steel substrate. The photo-current conversion efficiency was tested under an AM 1.5 solar simulator. The dye-sensitized solar cell device has a short current density of 8.22 mA cm^–2, open voltage of 0.71 V, fill factor of 0.59, and conversion efficiency of 3.4%. The internal impedance of the dye-sensitized solar cell was detected and simulated using an electrical impedance spectra technique with inductance, resistance, and capacitance characteristics. The stainless-steel/titania, titania/electrolyte, electrolyte, and electrolyte/(platinum/indium tin oxide) interfaces were simulated using an resistor–capacitor parallel circuit, and bulk materials such as stainless steel, tin doped indium oxide, and conducting wire were simulated by using a series of resistors and inductance.     

Effect of Cr-doping on the physicochemical properties of blue TiO2 and its application in dye-sensitized solar cells via low-temperature fabrication process

Cr-doped blue TiO₂ (Cr-BTiO₂) nanoparticles were fabricated at room temperature using lithium-ethylenediamine (Li-EDA) as reducing agent. The addition of Li-EDA promotes the selective reduction of the rutile phase of TiO₂ into the amorphous phase keeping anatase phase unaltered. Hence, the phase-selective reduction of TiO₂ leads to the formation of blue TiO₂ nanoparticles. Synthesized samples were characterized by equipment fitted with modern technology. The shifting of (101) peak to a lower angle (2θ) in Cr-BTiO₂ in X-ray diffraction (XRD) pattern suggests the successful doping of chromium into TiO₂ lattices. In Raman spectra, the shifting of the active Eg peak of Cr-BTiO₂ nanoparticles to higher wavenumber also suggests the successful substitution of Ti by Cr. The blue TiO₂ and Cr-BTiO₂ show increased absorption of light in the visible region compared to TiO₂ (P25). The modified TiO₂ samples have improved electron-hole separation tendency as predicted by the photoluminescence spectra (PL). Also, doping of Cr- into TiO₂ lattice results the formation of oxygen vacancy as detected by X-ray photoelectron spectroscopy (XPS). Among all samples, Cr-BTiO₂ demonstrated improvement in J_sc and overall incident photon to current conversion efficiency. Therefore, the synthetic effect is thus responsible for the enhancement in efficiency of Cr-BTiO₂ towards the dye-sensitized solar cell (DSSC) by 2.5 and 1.5 times higher than the P25 and blue TiO₂, respectively.     

Efficiency improvement of dye-sensitized solar cells based on electrodeposited TiO2 films by low temperature post-treatment

Porous crystalline TiO₂ films can be prepared at low temperatures (80 °C) by surfactant-assisted electrodeposition from TiCl₃ solution. Nevertheless, up to now calcination at high temperatures (typically 450 °C) was still necessary to establish a good performance of these films in dye-sensitized solar cells (DSSC). With this study we report that water vapour treatment at much lower temperatures (150 °C) for 1 week improves the performance of the films in DSSC to the same degree as calcination although the overall crystallinity remains lower. Reason for the good efficiency is that the porous structure stays intact and thus the dye molecules can be better adsorbed. Avoiding high temperatures during the preparation process of TiO₂ films for the application in DSSC enables the use of polymer substrates for the fabrication of flexible solar cells.     

Polyvinyl pyrrolidone aided preparation of TiO2 films used in flexible dye-sensitized solar cells

Polyvinyl pyrrolidone (PVP) is introduced to low temperature preparation of a good quality TiO₂ film used in flexible dye-sensitized solar cells (DSSCs). The samples are characterized by scanning electron microscopy and UV–vis absorption spectra, the photovoltaic performance of the DSSC is measured. It is found that PVP can improve the dispersion of TiO₂ particles and the adherence of TiO₂ particles to flexible substrate, as well as the adsorption of sensitized dye to TiO₂ film. Additionally, ultraviolet light irradiation can eliminate organics remained on the surface the TiO₂ film and improve the surface state of TiO₂ film. Under an optimal condition, a flexible DSSC using TiO₂ film doped PVP and UV irradiation treated achieves a light-to-electric energy conversion efficiency of 3.02% under irradiation with a simulate solar light intensity of 100 mW cm⁻².     

Using hybrid silica-conjugated TiO2 nanostructures to enhance the efficiency of dye-sensitized solar cells

In this study, hybrid silica-conjugated TiO₂ photoelectrodes were developed in order to enhance the efficiency of a dye-sensitized solar cell. The relative changes in surface crystallite size and chemical surface states of TiO₂ composites were investigated by XRD, XPS, and UV-vis spectroscopy. Therein, the chemical compositions of the nanostructured photoelectrode surfaces were observed to significantly change when the glass powder Si atoms became chemically bonded with the Ti atoms on the photoelectrode surface without appreciable changes to the crystalline structure of TiO₂. Furthermore, a significant conversion of Si-O_x into Si-O at the surface of the photoelectrode was observed following the addition of glass powder, which confirms the covalent bonding of Si and Ti atoms into Ti-O-Si. A maximum cell efficiency (η from 5.8% to 8.5%) was observed when 2 wt% of the low-temperature glass powder was added to the TiO₂ with a constant amount of dye loading. This observed peak in solar cell efficiently is most likely due to an increase in light harvesting, which is a result of an enhancement of light scattering and the coordination between Ti and Si to establish a Ti-O-Si bond.     

Electrophoretic deposition of TiO2 film on titanium foil for a flexible dye-sensitized solar cell

Electrophoretic deposition (EPD) method is employed to obtain mesoporous TiO₂ film on a titanium (Ti) foil; the film is then mechanically compressed and sintered at 350 °C before being subjected to dyeing. A comprehensive study was made on the mechanistic aspects of the EPD process. The dye-sensitized solar cell (DSSC) using the thus formed TiO₂ film rendered a power conversion efficiency (Eff.) of 6.5%. Effects of various compression pressures on the photovoltaic parameters and on other characteristic parameters of the pertinent DSSCs are studied. Electrochemical impedance spectroscopy (EIS) is applied for the first time, using a novel equivalent model, to study the impedance behavior of the DSSC with this type of TiO₂ film. We also obtain characteristic parameters of the TiO₂ photoanode by using EIS. The coordination number of the TiO₂ film, and the ratio of charge transfer resistances of electron recombination and electron transport are also obtained and analyzed. Moreover, we employ a multilayer approach and increase the film thickness to prepare TiO₂ films with the same coordination number and porosity; DSSCs using such TiO₂ films obtained from P90 and P25 rendered efficiencies of 6.5% and 5.24%, respectively. Scanning electron microscopy (SEM) micrographs are obtained to characterize the TiO₂ films formed by the EPD technique and laser-induced transient technique is used to estimate the electron lifetime in the TiO₂ films.     

TiO2-B narrow nanobelt/TiO2 nanoparticle composite photoelectrode for dye-sensitized solar cells

In order to possess the merits of both building blocks, i.e. the rapid interfacial electron transport of TiO₂-B narrow nanobelts (NBs) and the high surface area of TiO₂ nanoparticles (NPs), the TiO₂-B NBs and TiO₂ NPs composites photoelectrodes were prepared with different weight ratios. The dye-sensitized solar cell prototypes were fabricated based on the composite photoelectrodes and the photoelectrical properties have been systematically studied. Although the amount of adsorption dye of composite solar cells decreased, the composite cells could obtain higher power conversion efficiency compared to pure TiO₂ NP solar cell by rational tuning the weight ratio of TiO₂-B NBs and TiO₂ NPs, which was due to the faster electron transfer rate. The dye adsorption amount and interfacial electron transport, which together determined the overall photoelectrical conversion efficiency, were investigated by the UV–vis spectra, the electrochemical impedance spectra (EIS), intensity-modulated photocurrent spectroscopy (IMPS) and intensity-modulated photovoltage spectroscopy (IMVS).     

Performance enhancement of dye-sensitized solar cells using nanostructural TiO2 films prepared by a graft polymerization and sol–gel process

Nanostructural TiO₂ films with large surface areas were prepared by the combined process of graft polymerization and sol–gel for use in dye-sensitized solar cells (DSSCs). The surface of the TiO₂ nanoparticles was first graft polymerized with photodegradable poly(methyl methacrylate) (PMMA) via atom transfer radical polymerization (ATRP), after which the particles were deposited onto a conducting glass. The PMMA chains were removed from the TiO₂ films by UV irradiation to generate secondary pores, into which titanium isopropoxide (TTIP) was infiltrated. The TTIP was then converted into small TiO₂ particles by calcination at 450 °C, as characterized by energy-filtering transmission electron microscopy (EF-TEM) and field emission scanning electron microscopy (FE-SEM). The nanostructural TiO₂ films were used as a photoelectrode in solid-state DSSCs; the energy conversion efficiency was 5.1% at 100 mW/cm², which was higher than the values achieved by the pristine TiO₂ (3.8%) and nongrafted TiO₂/TTIP photoelectrodes (3.3%). This performance enhancement is primarily due to the increased surface area and pore volume of TiO₂ films, as revealed by the N₂ adsorption–desorption isotherm.     

Fabrication and photoelectrochemical properties of TiO2 films on Ti substrate for flexible dye-sensitized solar cells

The dye-sensitized solar cells (DSSCs) using Ti foil supporting substrate for fabricating nanocrystalline TiO₂ flexible film electrodes were developed, intending to improve the photoelectrochemical properties of flexible substrate-based DSSCs. The obtained cells were characterized by electrochemical impedance spectra (EIS), open circuit voltage decay (OCVD) measurement and Tafel plots. The experimental results indicate that the most important advantage of a Ti foil-based TiO₂ flexible electrode over a FTO glass-based electrode lies in its reduced sheet resistance, electron traps, and the retarded back reaction of electrons with tri-iodine ions in DSSCs. All above characteristics for the Ti substrate TiO₂ films are beneficial for decreasing the charge recombination in the TiO₂ electrode and prolonging the electron lifetimes for the DSSCs, as well as improvement of the overall solar conversion efficiency. The photocurrent of the cell fabricated with the Ti foil-based flexible electrode increased significantly, leading to a much higher overall solar conversion efficiency of 5.45% at 100 mW/cm² than the cell made with FTO glass-based TiO₂ electrodes. Above results demonstrate that Ti foil is a potential alternative to the conventional FTO glass substrate for the DSSCs.     

TiO2 films prepared by micro-plasma oxidation method for dye-sensitized solar cell

Nanocrystalline TiO₂ films are widely investigated as the electrodes of dye-sensitized solar cell(s) with different preparation methods. In this paper, thin titanium dioxide films have been prepared on titanium plates by the micro-plasma oxidation method in the sulfuric acid solution. The thin TiO₂ films were sensitized with a cis-RuL₂(SCN)₂·2H₂O (L = cis-2,2′-bipyridine-4,4′-dicarboxylic acid) ruthenium complex and implemented into a dye-sensitized solar cell configuration. The influence of reaction current density (10, 15, 20, 25 and 30 A dm⁻²) on the structural and the surface morphology of the films was investigated by X-ray diffraction, scanning electron microscopy, atom force microscopy and X-ray photoelectricity spectroscopy. Impedance analysis for dye-sensitized solar cells was carried out by electrochemical impedance spectroscopy. The results show that the rise of current density leads to the increase in the amount of rutile and the thickness of the TiO₂ film, which makes the TiO₂ films have different photovoltages and photocurrents. The relatively higher photoelectricity properties were obtained in the TiO₂ films prepared at a current density of 20 A dm⁻². The open-circuit voltage and the short-circuit current are 605 mV and 165 μA cm⁻², respectively.     

Fabrication of hole-patterned TiO2 photoelectrodes for solid-state dye-sensitized solar cells

We suggest a simple process to fabricate a hole-patterned TiO₂ electrode for a solid-state dye-sensitized solar cell (DSSC) to enhance cell performance through interfacial properties of the electrode with the electrolyte with minimum dye loading. The method involves prepatterning of SU-8 photoresist on a conducting glass, followed by the deposition of a nanocrystalline TiO₂ layer, calcination at 450 °C and characterization using scanning electron microscopy (SEM). Hole-patterned TiO₂ photoelectrodes yielded better solar energy conversion efficiency per dye loading compared to a conventional non-patterned photoelectrode. For example, a 50 μm hole-patterned DSSC exhibited 4.50% conversion efficiency in the solid state, which is comparable to an unpatterned flat TiO₂ photoelectrode (4.57%) however the efficiency per dye loading of the former (0.986%/g) was much greater than that of the latter (0.898%/g). The improvement was attributed to improved transmittance through the electrode as well as better interfacial properties between the electrolyte and electrode, as confirmed by UV-visible spectroscopy and electrochemical impedance (EIS) analysis.