Sonochemical preparation and characterization of SrZrxTi1−xO3/CdS composites

CdS nanoparticles coating SrZr_xTi_1−xO₃ (x=0.27) microparticles were obtained by sonochemical reaction, and the as-prepared composites products were characterized by TEM, XRD, FT-IR and other techniques and the fabrication mechanism was also discussed. Moreover, the photocatalystic properties of the final products were investigated by degradation of methylene blue. By coating CdS nanoparticles, the absorption of the UV-Vis spectrum of SrZr_xTi_1−xO₃ red-shifted, but the emission fluorescence spectrum blue-shifted. Adjusting the reactant concentration can control the thickness of the CdS layer.     

Interband transition studies of one-side modulation-doped AlxGa1−xAs/InyGa1−yAs/GaAs asymmetric step quantum wells

The results of S-dH measurements and the observation of quantum Hall plateaus at 1.5 K clearly demonstrated the existence of a 2DEG in modulation-doped Al_xGa_1−xAs/In_yGa_1−yAs/GaAs asymmetric step quantum wells. The PL data measured at several temperatures showed that the excitonic transition from the ground electronic subband to the ground heavy-hole band (E₀-HH₁) shifted to the lower energy side with increasing temperature. The value of the (E₀-HH₁) excitonic transition obtained from the PL measurements was in reasonable agreement with that determined from self-consistent calculations.     

Structure and optical properties of AlxZn1−xO alloys by sol-gel technique

Al_xZn_1−xO (x = 0-0.5) thin films were prepared on quartz glass substrates by sol-gel technique. X-ray diffraction (XRD), scanning electron microscope (SEM), and X-ray photoelectron spectroscopy (XPS) were employed for microstructure characterization of these thin films. In films with up to 20 at.% Al incorporation, compound nano-crystal phase was observed while wurtzite structure disappeared. Zn3d electron binding energy and Zn LMM‘s chemical shift were both increased by more than 0.4 eV. Transmittance spectra revealed that these films possessed high transmittance in the visible region, and the end of UV absorption edge shifted to less than 300 nm when Al content exceeds 20 at.% due to quantum confinement effect.     

Plasmon-phonon and plasmon-two different phonon interaction in Pb1−xMnxTe mixed crystals

Far-infrared reflection spectra in wide temperature range was used to investigate the vibrational properties of Pb_1−xMn_xTe (x = 0.0002, 0.002, 0.02 and 0.1) mixed crystals. To analyse the experimental results we use dielectric function that takes into account the existence of plasmon-phonon as well as the plasmon-two different phonon interaction. The best fit method revealed two frequencies of plasmon-phonon coupled modes and three frequencies of plasmon-two different phonon coupled modes. Further, the values for two different LO modes and plasma frequency (ω_P) are calculated. Results obtained from experimental spectra as the best fit, are in very good agreement with the theoretical prediction. The model of phonon behaviour based on Genzel's model was developed. It was found that the long wavelength optical phonon modes of these mixed crystals, exhibit an intermediate and two mode behaviour, coincidentally.     

Ethanol-thermal synthesis of Cd1−xZnxS nanoparticles with enhanced photodegradation of 4-chlorophenol

Cd_1−xZn_xS nanoparticles were prepared by a one-pot solvothermal process from Zn(CH₃COO)₂, Cd(CH₃COO)₂ and NaS₂CNEt₂·3H₂O (sodium diethyldithiocarbamate, DDTC). The Cd_1−xZn_xS nanoparticles were characterized by X-ray powder diffraction, transmission electron microscope and high-resolution transmission electron microscope equipped with an energy-dispersive X-ray spectrometer. The absorption spectra of the Cd_1−xZn_xS nanoparticles can be tuned into visible region by modulating stoichiometric ratio between Zn and Cd. With the increase of Zn content, the Cd_1−xZn_xS nanoparticles showed an enhanced photocatalytic activity on degradation of 4-chlorophenol. The Cd_1−xZn_xS prepared under the optimal experimental condition (initial Zn/Cd = 3:1, 210 °C, 24 h, in ethanol) possessed the best photocatalytic activity. The conversion ratio could reach up to 84% after 12 h under irradiation of visible light for Cd_1−xZn_xS prepared in ethanol, which was obviously superior to those of products prepared in water. These results showed that both crystallinity and synthetic medium were responsible for the enhanced photocatalytic activity for 4-chlorophenol.     

Luminescence characterization of (Ca1−xSrx)(S1−ySey):Eu,M (M = Sc and Y) for high color rendering white LED

The highly efficient red phosphors (Ca_1−xSr_x)(S_1−ySe_y):Eu²⁺,M³⁺ (M = Sc and Y) were prepared, starting from CaCO₃, SrCO₃, Eu₂O₃, Sc₂O₃, Y₂O₃, S, and SeO₂ with a flux, by a conventional solid-state reaction. The optimized red phosphors converted 11.8% (Sc³⁺) and 11.7% (Y³⁺) of the absorbed blue light into luminescence. These quantum values are much higher than Q = 3.0% of CaS:Eu²⁺. For the fabrication of light-emitting diodes (LEDs), the prepared phosphors were coated with MgO from non-aqueous solution to overcome their weakness against moisture. White LEDs were fabricated by pasting the prepared red phosphors and the yellow YAG:Ce³⁺ phosphor on an InGaN blue chip (λ_ems = 446.5 nm). The incorporation of the red phosphor to the YAG:Ce³⁺ phosphor resulted in an improved color rendering index (Ra) from 70 to 80.     

Multifunctional Zn0.99−xMn0.01CuxS nanowires: Structure, luminescence and magnetism

The wurtzite-type Zn_0.99−xMn_0.01Cu_xS (x = 0, 0.003, 0.01) nanowires were prepared by a simple hydrothermal method at 180 °C. The structure and morphology of the samples were characterized by X-ray diffraction (XRD), X-ray absorption fine structure (XAFS), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), field emission scanning electron micrograph (FESEM) and X-ray photoelectron spectrum (XPS). The results showed that both the Mn²⁺ and Cu²⁺ ions substituted for the Zn²⁺ sites in the host ZnS. The ethylenediamine-mediated template was observed, which was used to explain the growth mechanism of the nanowires. The color-tunable emission can be obtained by adjusting the concentrations of Mn²⁺ and Cu²⁺ ions. The ferromagnetism was observed around room temperature.     

Decomposition of (Ti2xFe1−xSb1−x)O4 solid solutions below 1673 K

The pseudo-binary TiO₂-FeSbO₄ system was investigated by means of thermogravimetric analysis below 1673 K in O₂. Rutile-type solid solutions were synthesised at 1373 K in O₂ by means of a solid state reaction between the two pure end members TiO₂ (rutile) and FeSbO₄ mixed in stoichiometric amounts. Thermal stability of the (Ti_2xFe_1−xSb_1−x)O₄ solid solution increases with rutile content; equimolar (Ti_1.00Fe_0.50Sb_0.50)O₄ solid solutions decompose at about 1673 K forming a TiO₂-enriched solid solution and FeSbO₄, that subsequently decomposes into Fe₂O₃ (hematite) and a volatile Sb oxide, probably Sb₄O₆. For compositions characterised by higher Ti content the decomposition temperature is higher than 1673 K.     

Optical properties of nanocrystalline Ga1−xInxSb/SiO2 films

Ga_1−xIn_xSb (x=0.19, 0.38, 0.63) nanoparticles embedded in a SiO₂ matrix were grown on the glass substrates by radio-frequency magnetron co-sputtering. X-ray diffraction patterns strongly support the existence of nanocrystalline Ga_1−xIn_xSb in the SiO₂ matrix. The changes in binding energies with Ga_1−xIn_xSb nanocrystals deposition have been directly observed by X-ray photoemission spectroscopy, and these show the existence of Ga_1−xIn_xSb nanocrystals in the SiO₂ matrix. Room-temperature Raman spectra show that the Raman peaks of the Ga_1−xIn_xSb-SiO₂ composite film have a larger red-shift of about 95.3 cm⁻¹ (longitudinal-optical mode) and 120.1 cm⁻¹ (transverse-optical mode) than that of bulk GaSb, suggesting the existence of phonon confinement and tensile stress effects. Additionally, the room-temperature optical transmission data exhibit a large blue-shift with respect to that of the bulk semiconductor due to the strong quantum confinement effect.     

Influence of SnO2 addition on the thermoelectric properties of Zn1 − xSnxO (0.01 ≤ x ≤ 0.05)

The grain size and the density of the Zn_1 − xSn_xO (0 ≤ x ≤ 0.05) samples decreased with increasing SnO₂ content. The addition of a small amount of SnO₂ (x ≤ 0.01) to ZnO led to an increase in both the electrical conductivity and the absolute value of the Seebeck coefficient, resulting in a significant increase in the power factor. The thermoelectric power factor was maximized to a value of 1.25 × 10⁻³ Wm⁻¹ K⁻² at 1073 K for the Zn_0.99Sn_0.01O sample.     

Synthesis and photoluminescence properties of aligned Zn2GeO4 coated ZnO nanorods and Ge doped ZnO nanocombs

Aligned Zn₂GeO₄ coated ZnO nanorods and Ge doped ZnO nanocombs were synthesized on a silicon substrate by a simple thermal evaporation method. The structure and morphology of the as-synthesized nanostructure were characterized using scanning electron microscopy and transmission electron microscopy. The growth of aligned Zn₂GeO₄ coated ZnO nanorods and Ge doped ZnO nanocombs follows a vapor-solid (VS) process. Photoluminescence properties were also investigated at room temperature. The photoluminescence spectrum reveals the nanostructures have a sharp ultraviolet luminescence peak centered at 382 nm and a broad green luminescence peak centered at about 494 nm.     

Ba3ZnTa2−xNbxO9 and Ba3MgTa2−xNbxO9 (0≤x≤1): synthesis, structure and dielectric properties

Oxides belonging to the families Ba₃ZnTa_2−xNb_xO₉ and Ba₃MgTa_2−xNb_xO₉ were synthesized by the solid state reaction route. Sintering temperatures of 1300°C led to oxides with disordered (cubic) perovskite structure. However, on sintering at 1425°C hexagonally ordered structures were obtained for Ba₃MgTa_2−xNb_xO₉ over the entire range (0≤x≤1) of composition, while for Ba₃ZnTa_2−xNb_xO₉ the ordered structure exists in a limited range (0≤x≤0.5). The dielectric constant is close to 30 for the Ba₃ZnTa_2−xNb_xO₉ family of oxides while the Mg analogues have lower dielectric constant of ∼18 in the range 50 Hz to 500 kHz. At microwave frequencies (5-7 GHz) dielectric constant increases with increase in niobium concentration (22-26) for Ba₃ZnTa_2−xNb_xO₉; for Ba₃MgTa_2−xNb_xO₉ it varies between 12 and 14. The “Zn” compounds have much higher quality factors and lower temperature coefficient of resonant frequency compared to the “Mg” analogues.     

Luminescence properties of Ca1−xSrxSe:Ce phosphors and their potential application for GaN-based LEDs

A series of solid solution phosphors Ca_1−xSr_xSe:0.02Ce³⁺ were prepared using high-temperature solid-state reaction technique. Their diffuse reflectance and luminescent spectra at room temperature were investigated and discussed. The optical band gap E_g energies of CaSe and SrSe were derived. Because of its broad band absorption in the range of 400-500 nm, Ca_1−xSr_xSe:Ce³⁺ can suit the application requirements for GaN-based light-emitting diodes (LEDs). The emission wavelength and the coordinates systematic shift from yellowish green to bluish green with an increase in x of Ca_1−xSr_xSe:Ce³⁺. Using Dorenbos's empirical equation, the values of energies of the lowest f-d transition absorption E, redshift D and Stokes shift ΔS for Eu²⁺ in the same host were predicted. The results were in good agreement with the experimental data.     

Synthesis of non-stoichiometric Bi2O4−x by oxidative precipitation

Bi₂O_4−x, a Bi mixed-valence phase was prepared at 95 °C, by a precipitation process, in a basic medium with a highly oxidizing K₂S₂O₈/Na₂S₂O₈. This phase has a low thermal stability as it decomposes below 400 °C in a multiple step process by some O₂ losses prior to finally transforming into γ-Bi₂O₃. The as-prepared powders are 50-60 nm in size with a narrow size distribution. Optical spectra of Bi₂O_4−x exhibit a broad absorption band with a band gap of ∼1.4 eV as compared to 2.61 eV for Bi₂O₃. The composition of this non-stoichiometric phase, which crystallizes in cubic fluorite related structure with a cell parameter of 5.538(3) Å, is Bi₂O_{3.65 ± 0.10}.     

Synthesis and optical properties of (Gd1−x,Eux)2O2SO4 nano-phosphors by a novel co-precipitation method

(Gd_1−x,Eu_x)₂O₂SO₄ nano-phosphors were synthesized by a novel co-precipitation method from commercially available Gd₂O₃, Eu₂O₃, H₂SO₄ and NaOH starting materials. Composition of the precursor is greatly influenced by the molar ratio of NaOH to (Gd_1−x,Eu_x)₂(SO₄)₃ (the m value), and the optimal m value was found to be 4. Fourier transform infrared spectrum (FT-IR) and thermal analysis show that the precursor (m = 4) can be transformed into pure (Gd_1−x,Eu_x)₂O₂SO₄ nano-phosphor by calcining at 900 °C for 2 h in air. Transmission electron microscope (TEM) observation shows that the Gd₂O₂SO₄ phosphor particles (m = 4) are quasi-spherical in shape and well dispersed, with a mean particle size of about 30-50 nm. Photoluminescence (PL) spectroscopy reveals that the strongest emission peak is located at 617 nm under 271 nm light excitation, which corresponds to the ⁵D₀ → ⁷F₂ transition of Eu³⁺ ions. The quenching concentration of Eu³⁺ ions is 10 mol% and the concentration quenching mechanism is exchange interaction among the Eu³⁺ ions. Decay study reveals that the ⁵D₀ → ⁷F₂ transition of Eu³⁺ ions has a single exponential decay behavior.     

Dopant induced variations in microstructure and optical properties of CeO2 nanoparticles

Nanocrystalline CeO₂ particles doped in the range of 0-20% of Ca²⁺, La³⁺, and Zr⁴⁺ have been prepared from hydrothermal synthesis of nitrate solutions at 200 °C and the influences of the dopants on microstructure and optical properties of the nanoparticles have been investigated. The unit cell parameter is found to be modified by −0.39, +0.83 and +0.16% for doping of 20% Zr⁴⁺, La³⁺, and Ca²⁺, respectively. For each batch prepared, nanoparticles with a narrow size distribution of 5-15 nm have been obtained. A high-resolution transmission electron microscopy investigation reveals that these particles are single crystals mostly having hexagonal, square or circular two-dimensional projections. UV-visible spectra of doped powders exhibit shift of the absorption edge and absorption peak with respect to those of the undoped CeO₂ particles and has been attributed to compensation of Ce³⁺ and decreasing crystallite size as result of doping.     

Critical behaviour and magnetocaloric effect of nano crystalline La0.67Ca0.33Mn1−xFexO3 (x = 0.05, 0.2) synthesized by nebulized spray pyrolysis

The structure, critical exponents and magnetocaloric effect (MCE) of Nebulized Spray Pyrolysis (NSP) synthesized nano crystalline La_0.67Ca_0.33Mn_1−xFe_xO₃ (x = 0.05, 0.2) were investigated. The Reitveld refinement of XRD patterns show that the samples adopt an orthorhombic structure with Pnma space group. TEM inspection reveals that the average particle size is about 15 nm and 42 nm for NSP synthesized LCMFe_0.05 and LCMFe_0.2 samples respectively. The temperature and field dependent magnetization studies reveal the superparamagnetic state of La_0.67Ca_0.33Mn_0.95Fe_0.05O₃ and spin-glass-like state of La_0.67Ca_0.33Mn_0.8Fe_0.2O₃. The critical behaviour at the transition region studied using modified Arrott plot provides a second order nature of phase transition for both samples. The magnetocaloric studies show the maximum value of magnetic entropy change (ΔS_max) is in the range 2.3 J kg⁻¹ K⁻¹ at 158 K for LCMFe_0.05 and 0.3 J kg⁻¹ K at 92 K for LCMFe_0.2 respectively at 5 T field. The field dependence of the magnetic entropy changes are also analysed, which show a power law dependence (ΔS_M ∞ Hⁿ, n = 0.72 (2)) at transition temperature, T_C = 162 K for LCMFe_0.05 and n = 1.11(3) at 92 K for LCMFe_0.2.     

Crystal structures and properties of BiMn1−xAlxO3 with x = 0.03 and 0.1

Crystal structures of BiMn_0.97Al_0.03O₃ (I) at 300 and 470 K and BiMn_0.9Al_0.1O₃ (II) at 90 and 300 K were studied with synchrotron X-ray powder diffraction. The strong Jahn-Teller distortion, observed at 300 K in I and associated with orbital order, disappeared at 470 K completely for one site and partially for the second site. The Mn/Al-O distances were very close to each other in I at 470 K and in II at 90 and 300 K indicating that orbital order did not appear in II even at 90 K. Magnetic properties of I and II were investigated with specific heat, high-temperature dc magnetic susceptibility, and ac magnetic susceptibility using different driving ac and applied dc magnetic fields and different ac magnetic field frequencies. The anomaly on the specific heat associated with a magnetic transition was strongly suppressed in II compared with that of I and BiMnO₃.     

Hydrothermally-induced morphological transformation of GdVO4:Eu

The aim of the present study is to investigate the effect of a wide pH range on morphology and luminescence properties of europium-doped gadolinium vanadate (GdVO₄:Eu³⁺). GdVO₄:Eu³⁺ powders were hydrothermally synthesized at 180 °C for 24 h in a wide pH range. The as-synthesized powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and photoluminescence (PL) spectroscopy. The XRD results showed that GdVO₄:Eu³⁺ with the tetragonal structure formed at pH < 13 as a single phase and Gd(OH)₃ formed at pH ≥ 13 as a secondary phase. The SEM and TEM observations demonstrated the hydrothermally-induced morphological transformation of GdVO₄:Eu³⁺ powders by altering the pH of the synthesis solution. The possible mechanism for the morphological transformation was proposed. The intensities of the prominent peaks at 618 nm in the PL emission spectra of GdVO₄:Eu³⁺ powders considerably shift according to the specific morphology. The luminescence intensity of the octahedron- and rod-like GdVO₄:Eu³⁺ powders hydrothermally obtained at pH = 3 was the strongest one due to high packing density and high crystallinity as well as the extended reduction of the concentration of inherent defect states or adsorbed species.     

Silver nanoparticles: Large scale solvothermal synthesis and optical properties

Silver nanoparticles have been successfully synthesized by a simple and modified solvothermal method at large scale using ethanol as the refluxing solvent and NaBH₄ as reducing agent. The nanopowder was investigated by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), dynamic light scattering (DLS), UV-visible and BET surface area studies. XRD studies reveal the monophasic nature of these highly crystalline silver nanoparticles. Transmission electron microscopic studies show the monodisperse and highly uniform nanoparticles of silver of the particle size of 5 nm, however, the size is found to be 7 nm using dynamic light scattering which is in good agreement with the TEM and X-ray line broadening studies. The surface area was found to be 34.5 m²/g. UV-visible studies show the absorption band at ∼425 nm due to surface plasmon resonance. The percentage yield of silver nanoparticles was found to be as high as 98.5%.