Laser induced defects in laser doped solar cells

Laser doping offers a promising method to define selective emitters for solar cells. Its main advantage is the localised nature of the laser beam, which allows melting of the surface area without heating the bulk. The ability to perform this process over a dielectric film offers further benefits, such as the possibility of creating self‐aligned metallisation patterns simultaneously with the selective emitter formation. However, laser induced defects, contaminations and discontinuities in the selective emitter can reduce solar cell performance. In this work the influence of different dielectric films on defect formation is investigated. It was found that a thin oxide beneath the SiN_x improves the implied open circuit voltage of the solar cells for a wide range of laser output powers. Fewer defects were observed when using this SiO₂/SiN_x stack compared to the standard single SiN_x anti‐reflection coating layer. It was also found that the recrystallised silicon layer grows epitaxially according the substrate orientation. No dislocation or stacking faults were observed in deeper areas using transmission electron microscopy, although some defects were observed near the surface. Electron beam induced current images revealed discontinuities in junctions formed with high laser powers. We conclude that micro‐cracks create these discontinuities, which can potentially induce shunts. Finally, laser doped solar cells with a standard SiN_x and with a double SiO₂/SiN_x stack layer as anti‐reflection coating were compared. An efficiency of 18.4% on a large area commercial grade p‐type CZ substrate was achieved. Copyright © 2010 John Wiley & Sons, Ltd.     

Add‐on laser tailored selective emitter solar cells

An elegant laser tailoring add‐on process for silicon solar cells, leading to selectively doped emitters increases their efficiency η by Δη = 0.5% absolute. Our patented, scanned laser doping add‐on process locally increases the doping under the front side metallization, thus allowing for shallow doping and less Auger recombination between the contacts. The selective laser add‐on process modifies the emitter profile from a shallow error‐function type to Gaussian type and enables excellent contact formation by screen printing, normally difficult to achieve for shallow diffused emitters. The significantly deeper doping profile of the laser irradiated samples widens the process window for the firing of screen printed contacts and avoids metal spiking through the pn‐junction. Copyright © 2010 John Wiley & Sons, Ltd.     

Laser ablation of SiO2 for locally contacted Si solar cells with ultra‐short pulses

We apply ultra‐short pulse laser ablation to create local contact openings in thermally grown passivating SiO₂ layers. This technique can be used for locally contacting oxide passivated Si solar cells. We use an industrially feasible laser with a pulse duration of τ_pulse ∼ 10 ps. The specific contact resistance that we reach with evaporated aluminium on a 100 Ω/sq and P‐diffused emitter is in the range of 0·3–1 mΩ cm². Ultra‐short pulse laser ablation is sufficiently damage free to abandon wet chemical etching after ablation. We measure an emitter saturation current density of J_0e = (6·2 ± 1·6) × 10⁻¹³ A/cm² on the laser‐treated areas after a selective emitter diffusion with R_sheet ∼ 20 Ω/sq into the ablated area; a value that is as low as that of reference samples that have the SiO₂ layer removed by HF‐etching. Thus, laser ablation of dielectrics with pulse durations of about 10 ps is well suited to fabricate high‐efficiency Si solar cells. Copyright © 2007 John Wiley & Sons, Ltd.     

Investigations of parasitic shunt resistance in n‐type buried contact solar cells

It has been shown that n‐type laser‐grooved buried contact solar cells exhibit a high‐efficiency potential, both on interdigitated backside buried contact (IBBC) and double‐sided buried contact (DSBC) cell structures. As the IBBC solar cell contains heavily doped, compensated regions, the shunt mechanisms are more complicated, and are different from those of the conventional front‐collecting‐junction solar cells. In this paper, several shunting mechanisms hindering the performances of the n‐type buried contact solar cells are investigated and discussed. The main shunting routes in n‐type IBBC solar cells are concluded as follows: (1) the emitter contact metal touching the n‐type substrate, which is either due to nonuniform boron deposition or diffusion‐induced misfit dislocations; (2) the base contact metal touching the p⁺ emitter, attributed to either the phosphorus groove diffusion being unable to compensate for the boron emitter diffusion, or the junction depth located in the diffusion overlap regions not deep enough to prevent nickel from spiking through the groove diffusion. The shunt resistance of the IBBC cells increased by more than two orders of magnitude after eliminating the shunt mechanisms discussed in this study. This led to an improvement in fill factor from 0·71–0·73 to 0·74–0·76, and an increase of average absolute efficiency of more than 0·65%. Copyright © 2005 John Wiley & Sons, Ltd.     

Influence of boron clustering on the emitter quality of implanted silicon solar cells: an atom probe tomography study

The use of ion implantation doping instead of the standard gaseous diffusion is a promising way to simplify the fabrication process of silicon solar cells. However, difficulties to form high‐quality boron (B) implanted emitters are encountered when implantation doses suitable for the emitter formation are used. This is due to a more or less complete activation of Boron after thermal annealing. To have a better insight into the actual state of the B distributions, we analyze three different B emitters prepared on textured Si wafers: (1) a BCl₃ diffused emitter and two B implanted emitters (fixed dose) annealed at (2) 950°C and at (3) 1050°C (less than an hour). Our investigations are in particular based on atom probe tomography, a technique able to explore 3D atomic distribution inside a material at nanometer scale. Atom probe tomography is employed here to characterize B atomic distribution inside textured Si solar cell emitters and to quantify clustering of B atoms. Here, we show that implanted emitters annealed at 950 °C present maximum clusters due to poor solubility at lower temperature and also highest emitter saturation current density (J_0e = 1000 fA/cm²). Increasing the annealing temperature results in greatly improved J_0e (131 fA/cm²) due to higher solubility and a consequently lower number of clusters. BCl₃ diffused emitters do not contain any B clusters and presented the best emitter quality. From our results, we conclude that clustering of B atoms is the main reason behind higher J_0e in the implanted boron emitters and hence degraded emitter quality. Copyright © 2015 John Wiley & Sons, Ltd.     

Fine line printed silicon solar cells exceeding 20% efficiency

Silicon solar cells with passivated rear side and laser‐fired contacts were produced on float zone material. The front side contacts are built up in two steps, seed and plate. The seed layer is printed using an aerosol jet printer and a silver ink. After firing this seed layer through the silicon nitride layer, the conductive layer is grown by light induced plating. The contact formation is studied on different emitter sheet resistances, 55 Ω/sq, 70 Ω/sq, and on 110 Ω/sq. These emitters are passivated with a PECVD silicon nitride layer which also acts as an anti‐reflection coating. Even on the 110 Ω/sq emitters it was possible to reach a fill factor of 80·1%. The electrical properties i.e., the contact resistance of the front side contacts are studied by transfer length model (TLM) measurements. On a cell area of 4 cm² and emitter sheet resistance of 110 Ω/sq, a record efficiency of 20·3% was achieved. Excellent open‐circuit voltage (V_oc) and short‐circuit current (j_sc) values of 661 mV and 38·4 mA/cm² were obtained due to the low recombination in the 110 Ω/sq emitter and at the passivated rear surface. These results show impressively that it is possible to contact emitter profiles with a very high efficiency potential using optimized printing technologies. Copyright © 2008 John Wiley & Sons, Ltd.     

>16% thin‐film epitaxial silicon solar cells on 70‐cm2 area with 30‐µm active layer,porous silicon back reflector,and Cu‐based top‐contact metallization

We demonstrate the use of a copper‐based metallization scheme for the specific application of thin‐film epitaxial silicon wafer equivalent (EpiWE) solar cells with rear chemical vapor deposition emitter and conventional POCl₃ emitter. Thin‐film epitaxial silicon wafer equivalent cells are consisting of high‐quality epitaxial active layer of only 30 µm, beneath which a highly reflective porous silicon multilayer stack is embedded. By combining Cu‐plating metallization and narrow finger lines with an epitaxial cell architecture including the porous silicon reflector, a J_sc exceeding 32 mA/cm² was achieved. We report on reproducible cell efficiencies of >16% on >70‐cm² cells with rear epitaxial chemical vapor deposition emitters and Cu contacts. Copyright © 2011 John Wiley & Sons, Ltd.     

Analytical models for the series resistance of selective emitters in silicon solar cells including the effect of busbars

A theoretical analysis of the power loss and series resistance of the front side emitter in silicon solar cells is presented. Existing 1D models (infinitely long finger) and 2D models (including the effect of busbars) of emitter series resistance contribution are extended to the case of selective emitters. The general case of different current densities for both emitters in the selective emitter scheme is considered in these extensions. The resulting models depend on the individual sheet resistances and current densities in both emitters and the device's overall grid geometry. The models are corroborated by finite element simulation of the potential in the emitter. An excellent agreement is found between the analytical models, and the simulations for a wide range of sheet resistances typically encountered in silicon solar cells. Grid simulations using the 2D model are applied to solar cells with selective emitters, where the width of the low‐resistive emitter was varied. The simulations demonstrate that the 2D model can explain the absolute change in fill factor observed in these cells. Copyright © 2013 John Wiley & Sons, Ltd.     

Numerical simulations of buried emitter back‐junction solar cells

We recently introduced the buried emitter back‐junction solar cell, featuring large area fractions of overlap between n⁺‐type and p⁺‐type regions at the rear side of the device. In this paper we analyse the performance of the buried emitter solar cell (BESC) and its generalisations by one‐dimensional device simulations and analytical model calculations. A key finding is that the generalised versions of the BESC structure allows achieving very high efficiencies by passivating virtually the entire surface of p‐type emitters by an oxidised n‐type surface layer. A disadvantage of this type of full‐area emitter passivation in the generalised back‐junction BESC is the need for an insulating layer between the metallisation of the emitter and the contact to the base, which is technologically difficult to achieve. Copyright © 2009 John Wiley & Sons, Ltd.     

Excellent boron emitter passivation for high‐efficiency Si wafer solar cells using AlOx/SiNx dielectric stacks deposited in an industrial inline plasma reactor

Excellent passivation of boron emitters is realised using AlO_x/SiN_x dielectric stacks deposited in an industrial inline plasma‐enhanced chemical vapour deposition reactor. Very low emitter saturation current density (J_0e) values of 10 and 45 fA/cm² are obtained for 180 and 30 Ω/sq planar p⁺ emitters, respectively. For textured p⁺ emitters, the J_0e was found to be 1.5–2 times higher compared with planar emitters. The required thermal activation of the AlO_x films is performed in a standard industrial fast‐firing furnace, making the developed passivation stack industrially viable. We also show that an AlO_x thickness of 5 nm in the AlO_x/SiN_x stack is sufficient for obtaining a J_0e of 18 fA/cm² for planar 80 Ω/sq p⁺ emitters, which corresponds to a 1‐sun open‐circuit voltage limit of the solar cell of 736 mV at 25 °C. Copyright © 2012 John Wiley & Sons, Ltd.     

Nickel silicide contacts formed by excimer laser annealing for high efficiency solar cells

Driven by the relatively high cost of silver (Ag), interest has grown in the photovoltaic (PV) industry to substitute conventional screen printed (SP) Ag front contacts with copper (Cu) plated contacts. The approach chosen here applies selective laser ablation of the front anti‐reflection coating (ARC), then forming self‐aligned nickel silicides (NiSi_x) contacts, and thickening the lines by Cu plating to achieve the desired line conductivity. A successful implementation of this scheme requires annealing to form NiSi_x with low contact resistance. However, it has been shown that industrial shallow emitters can be damaged severely upon conventional annealing of nickel. In this paper, we show that by using large area excimer laser annealing (ELA), NiSi_x contacts can be formed on industrial shallow emitters without the associated junction degradation. On the basis of sheet resistance, transmission electron microscopy, and lifetime measurements, we demonstrate that NiSi_x formation by ELA can be achieved in narrow contact openings without damaging the passivation and reflectance properties of the neighboring ARC. In addition, the thresholds for NiSi_x formation for different Ni thicknesses are quantified by rigorous finite element simulations and compared with experimental data. Finally, high efficiency passivated emitter and rear cell type solar cells featuring a shallow 85 Ω/sq emitter have been processed on large area CZ–Si using laser ablation of the ARC and subsequent NiSi_x formation by ELA. These cells show an average efficiency gain of 0.4%_abs compared with cells processed with reference SP contacts. In this work, the best performing cell with the ELA process reached 20.0% energy conversion efficiency. Copyright © 2013 John Wiley & Sons, Ltd.     

Evaluation of advanced p‐PERL and n‐PERT large area silicon solar cells with 20.5% energy conversion efficiencies

In this paper, we evaluate p‐type passivated emitter and rear locally diffused (p‐PERL) and n‐type passivated emitter and rear totally diffused (n‐PERT) large area silicon solar cells featuring nickel/copper/silver (Ni/Cu/Ag) plated front side contacts. By using front emitter p‐PERL and rear emitter n‐PERT, both cell structures can be produced with only a few adaptations in the entire process sequence because both feature the same front side design: homogeneous n⁺ diffused region with low surface concentration, SiO₂/SiN_x:H passivation, Ni/Cu/Ag plated contacts. Energy conversion efficiencies up to 20.5% (externally confirmed at FhG‐ISE Callab) are presented for both cell structures on large area cells together with power‐loss analysis and potential efficiency improvements based on PC1D simulations. We demonstrate that the use of a rear emitter n‐PERT cell design with Ni/Cu/Ag plated front side contacts enables to reach open‐circuit voltage values up to 676 mV on 1–2 Ω cm n‐type CZ Si. We show that rear emitter n‐PERT cells present the potential for energy conversion efficiencies above 21.5% together with a strong tolerance to wafer thickness and bulk resistivity. Copyright © 2014 John Wiley & Sons, Ltd.     

Thin Al2O3 passivated boron emitter of n‐type bifacial c‐Si solar cells with industrial process

We have presented thin Al₂O₃ (~4 nm) with SiN_x:H capped (~75 nm) films to effectively passivate the boron‐doped p⁺ emitter surfaces of the n‐type bifacial c‐Si solar cells with BBr₃ diffusion emitter and phosphorus ion‐implanted back surface field. The thin Al₂O₃ capped with SiN_x:H structure not only possesses the excellent field effect and chemical passivation, but also establishes a simple cell structure fully compatible with the existing production lines and processes for the low‐cost n‐type bifacial c‐Si solar cell industrialization. We have successfully achieved the large area (238.95 cm²) high efficiency of 20.89% (front) and 18.45% (rear) n‐type bifacial c‐Si solar cells by optimizing the peak sintering temperature and fine finger double printing technology. We have further shown that the conversion efficiency of the n‐type bifacial c‐Si solar cells can be improved to be over 21.3% by taking a reasonable high emitter sheet resistance. Copyright © 2017 John Wiley & Sons, Ltd.     

Development and experimental evaluation of a complete solar thermophotovoltaic system

We present a practical implementation of a solar thermophotovoltaic (TPV) system. The system presented in this paper comprises a sunlight concentrator system, a cylindrical cup‐shaped absorber/emitter (made of tungsten coated with HfO₂), and an hexagonal‐shaped water‐cooled TPV generator comprising 24 germanium TPV cells, which is surrounding the cylindrical absorber/emitter. This paper focuses on the development of shingled TPV cell arrays, the characterization of the sunlight concentrator system, the estimation of the temperature achieved by the cylindrical emitters operated under concentrated sunlight, and the evaluation of the full system performance under real outdoor irradiance conditions. From the system characterization, we have measured short‐circuit current densities up to 0.95 A/cm², electric power densities of 67 mW/cm², and a global conversion efficiency of about 0.8%. To our knowledge, this is the first overall solar‐to‐electricity efficiency reported for a complete solar thermophotovoltaic system. The very low efficiency is mainly due to the overheating of the cells (up to 120 °C) and to the high optical concentrator losses, which prevent the achievement of the optimum emitter temperature. The loss analysis shows that by improving both aspects, efficiencies above 5% could be achievable in the very short term and efficiencies above 10% could be achieved with further improvements. Copyright © 2012 John Wiley & Sons, Ltd.     

Process development and comparison of various boron emitter technologies for high‐efficiency (~21%) n‐type silicon solar cells

This paper shows for the first time a comparison of commercial‐ready n‐type passivated emitter , rear totally diffused solar cells with boron (B) emitters formed by spin‐on coating, screen printing, ion implantation, and atmospheric pressure chemical vapor deposition. All the B emitter technologies show nearly same efficiency of ~20%. The optimum front grid design (5 busbars and 100 gridlines), calculated by an analytical modeling, raised the baseline cell efficiency up to 20.5% because of reduced series resistance. Along with the five busbars, rear point contacts formed by laser ablation of dielectric and physical vapor deposition Al metallization resulted in another 0.4% improvement in efficiency. As a result, 20.9% efficient n‐type passivated emitter, rear totally diffused cell was achieved in this paper. Copyright © 2016 John Wiley & Sons, Ltd.     

Interconnection of busbar‐free back contacted solar cells by laser welding

We are presenting the module integration of busbar‐free back‐junction back‐contact (BJBC) solar cells. Our proof‐of‐concept module has a fill factor of 80.5% and a conversion efficiency on the designated area of 22.1% prior to lamination. A pulsed laser welds the Al metallization of the solar cells to an Al foil carried by a transparent substrate. The weld spots electrically contact each individual finger to the Al foil, which serves as interconnect between different cells. We produce a proof‐of‐concept module using busbar‐free cell strips of 25 × 125 mm². These are obtained by laser‐dicing of a 125 × 125 mm² BJBC solar cell. The fill factor of this module is increased by 3.5% absolute compared with the initial cell before laser‐dicing. This is achieved mainly by omitting the busbars and reduction of the finger length. The improvement of the module fill factor results in an increase in the module performance of 0.9% absolute before lamination in comparison with the efficiency of the initial 125 × 125 mm² BJBC solar cell. Hence, this interconnection scheme enables the transfer of high cell efficiencies to the module. Copyright © 2014 John Wiley & Sons, Ltd.     

Modeling the potential of screen printed front junction CZ silicon solar cell with tunnel oxide passivated back contact

Carrier selective passivated contacts composed of thin oxide, n + polycrystalline Si and metal on top of a n‐Si absorber can significantly lower the recombination current density (J_orear ≤8 fA/cm²) under the contact while providing excellent specific contact resistance (5–10 mΩ‐cm²); 25.1% efficient small area cells with photolithography front contacts on boron doped selective emitter and Fz wafers have been achieved by Fraunhofer ISE using their tunnel oxide passivated contact (TOPCon) approach. This paper shows a methodology to model such passivated contact cells using Sentaurus device model, which involves replacing the TOPCon region by carrier selective electron and hole recombination velocities to match the measured J_orear of the TOPCon region as well as all the light IV values of the cell. We first validated the methodology by modeling a 24.9% reference cell. The model was then extended to assess the efficiency potential of large area TOPCon cells on commercial grade n‐type Cz material with screen‐printed front contacts. To use realistic input parameters, a 21% n‐type PERT cell was fabricated on Cz wafer (5 Ω‐cm, 1.5‐ms lifetime). Modeling showed that the cell efficiency will improve to only 21.6% if the back of this cell is replaced by the above TOPCon, and the performance is limited by the homogenous emitter. Efficiency was then modeled to improve to 22.6% with the implementation of selective emitter (150/20 Ω/sq). Finally, it is shown that screen printing of 40‐µm‐wide lines and improved bulk material (10 Ω‐cm, 3‐ms lifetime) can raise the single side TOPCon Cz cell efficiency to 23.2%. Copyright © 2016 John Wiley & Sons, Ltd.     

Passivation of n‐type emitter and p‐type base in solar cells via oxygen terminated silicon nanoparticles

Various measurements and experiments are performed to establish the mechanism of passivation on emitter and base of conventionally manufactured solar cell with p‐type base. The surface coatings on the emitter are removed. The bare surface is then coated with silicon (Si) nanoparticles (NPs) with oxygen termination. It shows an increase in the cell efficiency up to 14% over bare surface of solar cell. The NPs show enhancement in light scattering from the surface, but shows an increase in the recombination lifetime indicating an improved passivation. When back contact is partially removed, the coating on bare back side ( p‐type) of the solar cell also improves the cell efficiency. This is also attributable to the increased recombination lifetime from the measurements. Same NPs are seen to degrade the surface of n and p‐type Si wafers. This apparently contradictory behaviour is explained by studying and comparing the emitter (n‐type) surface of the solar cell with that of n‐type Si wafer and the back surface ( p‐type) with that of p‐type Si wafer. The emitter surface is distinctly different from the n‐type wafer because of the shallow p–n junction causing the surface depletion. Back surface has aluminium (Al) metal trace, which plays an important role in forming complexes with the oxygen‐terminated Si NPs (Si–O NPs). With these studies, it is observed that increase in the efficiency can potentially reduce the thermal budget in solar cell preparation. Copyright © 2013 John Wiley & Sons, Ltd.     

8% Efficient thin‐film polycrystalline‐silicon solar cells based on aluminum‐ induced crystallization and thermal CVD

A considerable cost reduction could be achieved in photovoltaics if efficient solar cells could be made from polycrystalline‐silicon (pc‐Si) thin films on inexpensive substrates. We recently showed promising solar cell results using pc‐Si layers obtained by aluminum‐induced crystallization (AIC) of amorphous silicon in combination with thermal chemical vapor deposition (CVD). To obtain highly efficient pc‐Si solar cells, however, the material quality has to be optimized and cell processes different from those applied for standard bulk‐Si solar cells have to be developed. In this work, we present the different process steps that we recently developed to enhance the efficiency of pc‐Si solar cells on alumina substrates made by AIC in combination with thermal CVD. Our present pc‐Si solar cell process yields cells in substrate configuration with efficiencies so far of up to 8·0%. Spin‐on oxides are used to smoothen the alumina substrate surface to enhance the electronic quality of the absorber layers. The cells have heterojunction emitters consisting of thin a‐Si layers that yield much higher V_oc values than classical diffused emitters. Base and emitter contacts are on top of the cell in interdigitated finger patterns, leading to fill factors above 70%. The front surface of the cells is plasma textured to increase the current density. Our present pc‐Si solar cell efficiency of 8% together with the fast progression that we have made over the last few years indicate the large potential of pc‐Si solar cells based on the AIC seed layer approach. Copyright © 2007 John Wiley & Sons, Ltd.