含氨基聚芳醚酮/磺化聚芳醚酮砜中高温质子交换复合膜的制备与性能研究

以自制的高磺化度磺化聚芳醚酮砜(SPAEKS)和含有氨基的聚芳醚酮(Am-PAEK)为原料,通过共溶剂涂膜法制备了不同重量比例的Am-PAEK/SPAEKS复合膜.通过高温(160℃)处理使氨基和磺酸基团在复合膜内形成交联,制得交联型复合膜.复合膜的热性能、尺寸稳定性、阻醇性能有所提高,而且交联型复合膜中的Am-PAEK/SPAEKS-C-3质子传导率在120℃时达到了0.0892 S/cm,高于在相同测试条件下SPAEKS膜的0.0654 S/cm和Nafion膜的0.062 S/cm,而其甲醇渗透系数在25℃时达到0.14×10-6cm2/s,低于SPAEKS膜的0.85×10-6cm2/s和Nafion膜的2×10-6cm2/s.实验结果表明,Am-PAEK/SPAEKS交联型复合膜有望在中高温质子交换膜燃料电池中得到应用.     

铁酸镍/碳复合中空多壳层结构的制备及吸波性能

采用次序模板法合成了单、双壳层的中空铁酸镍(NiFe₂O₄)材料,通过改变前驱体溶液组成及煅烧条件等因素实现了对产物形貌的调控.在中空NiFe₂O₄颗粒表面原位包覆聚多巴胺,再经过碳化处理,制备了具有中空多壳层结构(HoMS)的NiFe₂O₄/C复合吸波材料;考察了其电磁参数,计算了其吸波性能,分析了不同复合结构对性能的影响.结果表明,中空多壳层结构能够显著降低材料的密度,而碳薄层不仅能够改善其阻抗匹配性,而且提升了材料的反射损耗性能.其中,双壳层NiFe₂O₄/C复合物的吸波性能最佳,当样品厚度为3.5 mm时,材料在8.44 GHz处反射损失最小,为-32.35 dB;当样品厚度为2.0 mm时,材料在14.01～17.69 GHz范围内反射损耗小于-10 d B,有效吸收频宽为3.68 GHz.这些优异性能主要源于独特的中空多壳层结构增加了电磁波多次反射/散射的概率,提供了更多的界面极化,实现了电磁波的快速...     

聚醚砜与含萘环的聚芳醚酮增容共混物的研究

以双酚S型含萘环的聚芳醚酮为增容剂,研究了对聚醚砜(PES)与对苯二酚型-1,4-萘环的聚芳醚酮(1,4-NA-PAEK)共混体系的相容性及力学性能.结果表明,双酚S型含萘环的聚芳醚酮可显著降低PES/NA-PAEK共混体系中NA-PAEK分散相尺寸,改善两组分间的相容性,并且增容剂的加入使共混体系形成了双连续的互锁结构,提高了共混物的力学性能.     

多孔羰基铁/SiO2/聚吡咯核壳结构复合材料的制备及电磁特性

首先对羰基铁进行点腐蚀得到多孔羰基铁,然后采用St?ber法和原位聚合法将SiO_2和导电高分子聚吡咯包覆在多孔羰基铁表面,制备多孔羰基铁/SiO_2/聚吡咯电磁复合吸波材料。采用XRD、SEM、TEM、FT-IR对样品结构、微观形貌进行了表征,在网络分析仪中采用同轴法测试样品电磁参数,并根据传输线理论研究了2~18 GHz微波频段内吡咯含量及涂层厚度对样品吸波性能的影响。实验结果表明:制备的多孔羰基铁/SiO_2/聚吡咯复合电磁吸波材料具有核壳结构;随着吡咯加入量的增加,吸波材料吸收峰逐渐向低频方向移动;当涂层厚度为3.5 mm、吡咯加入量为6%(w/w)时,在9.44~17.56 GHz范围内反射率均低于-10 d B,频带宽度为8.12 GHz,损耗反射率达到-23 d B。良好的吸波性能归因于复合物有效的阻抗匹配特性及多重界面极化效应,多孔羰基铁/SiO_2/聚吡咯是一种轻质、宽频、强吸收的吸波材料。     

ZnO纳米颗粒锚定的亚微米碳纤维的制备及其吸波性能

使用静电纺丝技术结合水热法制备了表面锚定ZnO纳米颗粒的亚微米碳纤维（ZnO/SDCFs）复合物,并详细研究了反应溶液的pH值对复合物的结构、组成、电磁特性和吸波性能的影响。结果显示,随着pH值的升高,ZnO的含量增加,介电常数、介电损耗以及电磁衰减能力均下降,但阻抗匹配程度提高。相比于纯碳纤维,所有ZnO/SDCFs复合物的吸波性能均得到不同程度的加强。其中,pH值等于8时所制备的ZnO/SDCFs-8复合物拥有最好的吸波性能,主要归因于电磁衰减能力和阻抗匹配间的更好平衡。当ZnO/SDCFs-8的填充量仅为2.5%（质量分数）、厚度为1.7 mm时,相应吸波涂层的最小反射损耗达到-44.1 dB,低于-10 dB的有效吸收带宽为6.1 GHz,频率范围为11.9~18 GHz;当厚度为3.0 mm时,有效吸收带宽可提高到11.8 GHz（6.2~18 GHz）。     

中空结构聚苯胺/Fe_3O_4/炭黑复合材料的制备及吸波性能

采用界面聚合和Pickering乳液聚合相结合的方法制备了具有微米尺寸的中空聚苯胺/Fe_3O_4/炭黑微球复合材料,研究了其形貌、电磁性能和吸波性能.结果表明,中空聚苯胺/Fe_3O_4/炭黑微球的平均粒径约为2.0μm;在2~4 GHz范围内的磁损耗主要是自然共振和交换共振,而在4~18 GHz范围内的磁损耗主要是涡流损耗;在2~18 GHz范围内,随着涂层厚度增加,反射损耗峰向低频方向移动,当涂层厚度增大到5.0mm时,反射损耗曲线出现2个反射损耗峰,分别位于C波段(4~8 GHz)和Ku波段(12~18 GHz),说明中空聚苯胺/Fe_3O_4/炭黑微球复合材料可作为特定频段的吸波材料.     

Fe-Ni/C复合纳米纤维的原位制备与微波吸收性能

采用静电纺丝技术结合稳定化和碳化处理原位制备了Fe-Ni/C复合纳米纤维, 其平均直径约为215 nm, 所生成的Fe-Ni合金纳米颗粒较均匀地分布在碳基纳米纤维的内部和表面, 且被石墨化碳层所包覆. 以Fe-Ni/C复合纳米纤维为吸收剂、 硅橡胶为基质制备成吸波涂层, 研究了碳化温度对电磁特性和微波吸收性能的影响. 结果表明, 涂层厚度为1.2~2.0 mm、 Fe-Ni/C复合纳米纤维质量分数为5%的吸波涂层表现出优良的微波吸收性能, 在7.4~18 GHz频率范围内的反射损耗均低于-20 dB; 随着复合纳米纤维的碳化温度由800 ℃升高到1200 ℃, 由于阻抗匹配特性的改善, 吸波涂层的微波吸收能力逐步加强, 其最小反射损耗由-22.6 dB降低到-63.0 dB.     

溶剂热法制备四氧化三铁/聚乙烯亚胺修饰的多壁碳纳米管复合粒子及其吸波性能

采用溶剂热法将磁性Fe_3O_4粒子附着在聚乙烯亚胺(PEI)修饰的多壁碳纳米管(MWNTs)表面,制备了兼具介电损耗和磁损耗的复合吸波微粒Fe_3O_4/MWNTs。利用X射线衍射仪(XRD)、傅里叶红外光谱仪(FTIR)、热重分析仪(TGA)、透射电子显微镜(TEM)及矢量网络分析仪等分析了Fe_3O_4/MWNTs复合粒子的结构、形貌和吸波性能。TEM结果表明,由于PEI的修饰作用,Fe_3O_4/MWNTs复合粒子具有良好的分散性。XRD结果显示,附着的Fe_3O_4粒子具有完整的晶型结构。吸波性能结果表明,PEI修饰的Fe_3O_4/MWNTs复合微粒拥有非常优异的吸波性能,随着厚度的增加,复合微粒的吸收峰向低频处移动。在厚度为3.2 mm,频率为6.16 GHz时,出现了最大反射损耗-42.9 d B,反射损耗大于-10 d B的频段为1.42 GHz(5.40~6.82 GHz)。     

花状Zn-MOF衍生碳@MoS2复合材料制备及吸波性能

采用Zn-MOF(MOF为金属有机骨架)制备纳米多孔碳材料,通过自组装法将多孔碳与花状MoS₂结合,制备出具有规整有序结构的花状Zn-MOF衍生碳@MoS₂复合吸波材料。基于Zn-MOF衍生纳米多孔碳的高孔隙率、大比表面积,MoS₂的花状结构引起的电磁波多次反射和散射,以及MoS₂和Zn-MOF衍生碳之间存在的强极化效应、良好的阻抗匹配和协同作用,Zn-MOF衍生碳@MoS₂在频率为9.28 GHz时的最佳反射损耗达到-49.68 dB,表现出优异的电磁波吸收性能。     

膨胀石墨/聚苯胺/Fe_3O_4复合材料的制备及吸波性能

采用原位聚合方法制备了膨胀石墨/聚苯胺(EG/PANI)复合材料,将Fe_3O_4负载于EG/PANI表面,得到具有电磁吸收性能的EG/PANI/Fe_3O_4复合材料.通过扫描电子显微镜(SEM)、X射线衍射仪(XRD)、傅里叶变换红外光谱仪(FTIR)及矢量网络分析仪(VNA)等对复合材料的形貌、成分和吸波性能进行了研究.吸波性能分析结果表明,当掺杂浓度为0.05 mol/L,匹配厚度d=2 mm时,样品的最小反射损耗(RLmin)在8.64 GHz处达到-37 dB.随着掺杂浓度的增加,最小反射损耗峰向低频移动,对应的匹配厚度逐渐变厚.材料的介电弛豫极化、涡流损耗及λ/4模型的干涉相消现象出现的双峰,使EG/PANI/Fe_3O_4复合材料在电磁波吸收领域有一定的应用前景.     

Lightweight excellent microwave absorption properties based on sulfur doped graphene

Lightweight and high-efficiency electromagnetic wave (EMW) absorption sulfur doped graphene (S-GS) was fabricated by reducing and doping graphene oxide (GO) using chemical method. The obtained S-GS exhibits an extremely low reflection loss (RL), wide effective absorption frequency bandwidth at a thin coating thickness (d), light weight and low cost. The minimum RL reaches −52.3 dB at 17.5 GHz with a matching thickness of 1.22 mm. More excitedly, the EM absorption properties could be double-adjusted. By changing the amount of dopant and the thickness of S-GS, The minimum RL touches −52.2 dB at 9.4 GHz and −49.3 dB at 8.5 GHz, respectively, even much lower than most kinds of GS based composites which combined with polymers, magnetic nanoparticles and so on. In a word, S-GS can be promised to be an ideal candidate for constructing novel MW absorber with lightweight, strong absorption characteristics, and thin matching thickness.     

新颖的电磁波吸收材料:Ba_(1-x)La_xFe_(10)Al_2O_(19)铁氧体的制备和性能

用溶胶-凝胶法合成了Ba1-xLaxFe10Al2O19铁氧体(x=0.00,0.05,0.10,0.15,0.20,0.25).通过粉末X射线衍射仪、扫描电子显微镜、透射电子显微镜、振动样品磁强计和矢量网络分析仪表征了样品的结构、形貌、磁性和电磁波吸收性能.结果表明,La含量显著地影响Ba1-xLaxFe10Al2O19铁氧体的磁性和电磁波吸收性能.Ba1-xLaxFe10Al2O19铁氧体的饱和磁化强度随La含量的增加而减小,而矫顽力则增大.当BaFe10Al2O19吸收剂的涂层厚度为2mm时,在8～18GHz范围内,反射损耗的峰值在13.45GHz处达到-26.3dB,有效带宽为8.9GHz.Ba1-xLaxFe10Al2O19铁氧体对电磁波的反射损耗和有效带宽低于母体BaFe10Al2O19.由于Ba1-xLaxFe10Al2O19样品良好的吸波性能,建议可以作为吸收和屏蔽电磁波的候选材料.     

Lightweight,Low-Cost Co2SiO4@diatomite Core-Shell Composite Material for High-Efficiency Microwave Absorption

The porous and biomimetic cobalt silicate@diatomite (Co₂SiO₄@diatomite) was successfully synthesized by a two-step method, including the hydrothermal method and calcination to improve the electromagnetic wave absorption property. Different hydrothermal times were well-tuned for Co₂SiO₄@diatomite composites with different loadings of Co₂SiO₄. Interestingly, the Co₂SiO₄@diatomite composites (6 h, 25 wt%) had a smaller minimum reflection loss. Moreover, the minimum reflection loss (RL_min) could reach −12.03 dB at 16.64 GHz and the matched absorber thickness was 10 mm, while the effective absorption bandwidth (EAB, RL ≤ −10 dB) could be 1.92 GHz. In principle, such findings indicate that Co₂SiO₄@diatomite nanocomposites could be a promising candidate for high-efficiency microwave absorption capability.     

Preparation of Reduced Graphene Oxide/MnO Composite and Its Electromagnetic Wave Absorption Performance

The composite containing reduced graphene oxide and MnO nanoparticles (RGO/MnO) has been prepared via a one step pyrolysis method. The MnO nanoparticles were uniformly dispersed on the surface of RGO nanosheets forming MnO/RGO composite. The composite displays a maximum absorption of ‒38.9 dB at 13.5 GHz and the bandwidth of reflection loss corresponding to –10 dB can reach 4.9 GHz (from 11.5 to 16.4 GHz) with a coating layer thickness of only 2 mm. Therefore, the obtained RGO/MnO composite a perfect lightweight and high-performance electromagnetic wave absorbent.

     

聚吡咯/Ba_(0.9)Nd_(0.1)Fe_(11.5)Cr_(0.5)O_(19)复合物的可控合成及电磁性能

用溶胶凝胶法制备了一系列Nd掺杂Ba-铁氧体粉末(Ba1-xNdxFe11.5Cr0.5O19,x=0.00,0.05,0.10,0.15,0.20),选取磁性能相对较好的Ba0.9Nd0.1Fe11.5Cr0.5O19作为磁核,通过原位聚合法制备了不同铁氧体含量的聚吡咯/Ba0.9Nd0.1Fe11.5Cr0.5O19(PPy/BNFCO)复合物.用X射线衍射(XRD)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、红外光谱(FTIR)、振动样品磁强计(VSM)、四探针测试仪和矢量网络分析仪等表征了铁氧体粉末和复合物微粒的结构、形貌以及电磁性能.结果表明,Nd的掺杂明显改变了Ba-铁氧体的饱和磁化强度和矫顽力;PPy/BNFCO复合物具有比较明显的核壳结构;复合物的饱和磁化强度随BNFCO含量的增加而增大;电导率则与PPy含量成正比,mpy/mBNFCO=5/1为复合体系渗流阈值;复合物对电磁波的反射损耗和有效带宽是PPy和ZCGFO协同作用的结果,当mpy/mBNFCO为5/1时,PPy/ZCGFO复合物中组分间的协同作用达到最大,其反射峰值和有效带宽分别达到-27.68dB和9.04GHz.PPy/ZCGFO复合物由于良好的微波吸收性能,有望成为电磁波吸收与屏蔽领域的候选材料.     

Enhanced Electromagnetic Wave Absorption Properties of Ultrathin MnO2 Nanosheet-Decorated Spherical Flower-Shaped Carbonyl Iron Powder

In this work, spherical flower-shaped composite carbonyl iron powder@MnO₂ (CIP@MnO₂) with CIP as the core and ultrathin MnO₂ nanosheets as the shell was successfully prepared by a simple redox reaction to improve oxidation resistance and electromagnetic wave absorption properties. The microwave-absorbing properties of CIP@MnO₂ composites with different filling ratios (mass fractions of 20%, 40%, and 60% after mixing with paraffin) were tested and analyzed. The experimental results show that compared with pure CIP, the CIP@MnO₂ composites have smaller minimum reflection loss and a wider effective absorption bandwidth than CIP (RL < −20 dB). The sample filled with 40 wt% has the best comprehensive performance, the minimum reflection loss is −63.87 dB at 6.32 GHz, and the effective absorption bandwidth (RL < −20 dB) reaches 7.28 GHz in the range of 5.92 GHz–9.28 GHz and 11.2 GHz–15.12 GHz, which covers most C and X bands. Such excellent microwave absorption performance of the spherical flower-like CIP@MnO₂ composites is attributed to the combined effect of multiple beneficial components and the electromagnetic attenuation ability generated by the special spherical flower-like structure. Furthermore, this spherical flower-like core–shell shape aids in the creation of discontinuous networks, which improve microwave incidence dispersion, polarize more interfacial charges, and allow electromagnetic wave absorption. In theory, this research could lead to a simple and efficient process for producing spherical flower-shaped CIP@MnO₂ composites with high absorption, a wide band, and oxidation resistance for a wide range of applications.     

Zn-Ni-Cu铁氧体/聚邻甲氧基苯胺复合物的制备及电磁性能

用共沉淀法和溶液原位聚合法分别制备了锌镍铜铁氧体粉末(ZNCF)及其聚邻甲氧基苯胺(POMA)复合物.用粉末X-射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、振动样品磁强计(VSM)等分别表征了产物的结构、形貌、电磁性能.结果表明,ZNCF/POMA复合物的组分之间存在一定的相互作用;POMA对ZNCF粒子的包覆能起到调控样品电磁性能的作用,复合物的磁性能随POMA含量的增加而减小,而电导率则相反;与单一组分相比,POMA/ZNCF复合物表现出更优良的电磁波吸收性能,ωZNCF为20%的复合物的反射损耗峰值和有效带宽分别为-27.32 dB和8.81 GHz,峰值对应的共振频率为11.61 GHz,是颇具应用前景的电磁波吸收材料.