钇掺杂对Ce0.33Zr0.67O2储氧性能的影响

采用柠檬酸溶胶凝胶法制备了一系列钇掺杂的富锆铈锆复合氧化物Ce0.33YxZr0.67-xO2,并通过XRD,BET,OSC,XPS,in-situ CO-FTIR等测试,系统研究了钇掺杂后铈锆复合氧化物储放氧性能的变化规律及其影响因素。结果表明,钇离子能够进入铈锆晶格形成固溶体,并提高铈锆体系的结构热稳定性。对于新鲜样,钇掺杂可大幅提升Ce0.33Zr0.67O2材料的比表面积,提高单位质量铈锆材料的储氧能力;但老化后,钇掺杂样品的储氧性能随着掺杂量的增加而减小。通过XPS及原位红外吸附性能测试证实,钇在Ce0.33Zr0.67O2材料表面主要取代锆离子,其掺杂会降低样品的表面吸附能力,抑制铈的氧化还原反应,从而导致该体系储氧性能的下降。     

Catalytic Performance of Ce／Zr Oxides Catalysts for Soot Combustion

Catalytic performances of a series Ce/Zr oxides(CexZr1-xO2 )for soot combustion were investigated. The catalytic activities for soot combustion were affected by both the Ce/Zr ratio and the oxygen storageinvestigated. Thecapability of Ce/Zr oxides. O2-TPD and TG-DTA results indicate that CexZr1-xO2 can release its lattice oxygen continuously and promote soot combustion even no oxygen occurs in the reaction atmosphere. Among these Ce/Zr oxides, Ce0.5Zr0.5O2 has the best catalytic activity, and the ignition temperature of soot combustion was about 410℃, which is close to the practical exhaust temperature of the diesel engine.     

铈锆比对储氧材料铈锆固溶体性能的影响

铈锆固溶体作为储氧材料在三效催化剂中起着不可替代的作用。从外围电子排布角度,分析稀土元素铈所具有的独特4f电子层,从结构上探讨铈离子在萤石结构中所起的作用,从而解释了铈作为储氧材料时所发挥的功效,即可在不同的氧气氛下缓冲氧。采用共沉淀法制备了一系列铈锆比不同(Ce/Zr值分别为2/3,1/1,3/2,3/1)的铈锆固溶体,样品经650℃焙烧6 h后,采用X射线衍射(XRD)、比表面积(BET)、程序升温还原(TPR)法、扫描电镜(SEM)分析测定了样品的晶粒度、比表面积、储氧量(OSC),并研究了Zr4+在CeO2晶格的固溶情况。研究发现采用共沉淀法可以成功制备出铈锆比不同的铈锆固溶体,样品具有纳米晶的特征,且XRD谱图显示衍射角随固溶体中Zr4+的增多而增大,由于Zr4+的离子半径小于Ce4+的离子半径,因此随Zr4+的加入产生晶格收缩,晶格常数变小;比表面积数值和储氧能力良好,铈锆比对比表面积和还原性没有显著影响,但储氧量数据却随Zr4+的加入明显增加;Zr4+的加入量对储氧材料固溶度也有影响,当掺杂Zr4+的量较多时,Zr4+会比较容易进入CeO2晶格。     

Preparation and Characterization of CeO2-ZrO2 Solid Solution Ultrafine Particles Using Reversed Microemulsion

The development of the TWCs (three-way cata-lysts) was dictated bythe need to si multaneously con-vert the three main pollutants inthe exhaust gases ,i .e .,hydrocarbons (HCs) ,COand NOxpresent in theautomotive exhaust to H2O, CO2and N2[1]. Highestconvers…     

Effect of Fe2O3 Loading Amount on Catalytic Properties of Monolithic Fe2O3/Ce0.67Zr0.33O2 -Al2O3 Catalyst for Methane Combustion

Ce0.67Zr0.33O2-Al2O3 solid solution was prepared by the co-precipitation method. Fe2O3-based catalysts supported on the solid solution were obtained by the impregnation method. The article revealed that the optimal loading amount of Fe2O3 on Ce0.67Zr0.33 O2-Al2O3 in our experimental condition for catalytic combustion of methane was 8% （ mass fraction）. The prepared catalysts were characterized by BET, TPR, XRD analyses, and their catalytic activity was investigated after being calcined at 873 K and after being aged in water gas at 1273 K. When the loading amount of Fe203 was 8% （ mass fraction）, the catalyst held the highest activity, and the best temperature speciality and thermal stability. The complete-conversion temperature of methane for fresh and aged sample was 788 and 838 K, respectively. The range between the light-off temperature and the complete-conversion temperature was only 15 K. The characterization results of XRD indicated that Fe2O3 was well dispersed on the Ce0.67Zr0.33O2-Al2O3 matrix. The results of BET and TPR were in good harmony with the catalytic activity results.     

CexZr1-xO2储氧材料制备方法研究进展

本文综述了共沉淀法、溶胶-凝胶法、水热法、高能球磨法等常用CexZr1-xO2储氧材料的合成方法,并进行了比较.阐述了CexZr1-xO2的基本改性机制,详述了稀土元素、碱土元素以及过渡金属对CexZr1-xO2的改性效果及原理.相关研究结果表明,CexZr1-xO2晶体结构、形貌、比表面积与其合成方法有很大关系,从而...     

NiO-Ce0.5Zr0.5O2 catalysts prepared by citric acid method for steam reforming of ethanol

NiO-Ce0.5Zr0.5O2catalysts were prepared by citrate method and used for hydrogen production from steam reforming of ethanol (SRE). The effect of nickel content and space velocity on the catalytic performance was investigated. The prepared catalysts were character-ized with XRD and thermal analysis techniques. 20%NiO-Ce0.5Zr0.5O2 catalyst was very active and selective for hydrogen production via SRE, in which ethanol conversion of 100% could be obtained with feed component of 20% (H2O+EtOH) and 80% N2, water/ethanol of 3/1 in molar ratio at 350 ℃. Also, the catalyst showed good stability for anti-sintering and carbon-resistance. The XRD illuminated that both NiO and Ce0.5Zr0.5O2 crystal sizes were very small in NiO-Ce0.5Zr0.5O2 catalyst, and Ce0.5Zr0.5O2 solid solution was formed.     

Dynamic Oxygen Storage Capacity Measurements on Ceria-Based Material

The constant increase in the number of environ-mental protection regulations worldwide has broughtabout significant restrictions onthe nature and quantityof exhaust gases originating from mobile sources suchas automobile emissions .These increasingly dema…     

Catalytic combustion study of soot on Ce0.7Zr0.3O2 solid solution

The Ce0.7Zr0.3O2 solid solution and CeO2 were prepared using the sol-gel method. The phase structure, crystallite sizes and the reducibility of the catalysts were characterized by XRD and H2-TPR techniques. XRD results indicated that Zr^4＋ had replaced part of Ce^4＋ to form a fluorite-like solid solution, which was favorable to obtain ultrafine nanoparticles. The ratio of main HE consumption for Ce0.7Zr0.3O2：CeO2 was 4.4：1.0, implying that the solid solution could improve the reducibility compared to the single CeO2. The Ce0.7Zr0.3O2 solid solution catalyst showed a sharp combustion peak at 397 ℃, which was 200 ℃ lower than that of the single soot. The good catalytic activity of the Ce0.7Zr0.3O2 was attributed to the formation of nano-CeO2-based solid solution, which enhanced the reducibility and then improved the combustion activity. As Ce0.7Zr0.3O2 could be easily reduced to Ce0.7Zr0.3O2-x meanwhile, after oxygenation, the Ce0.7Zr0.3O2.x was recovered to Ce0.7Zr0.3O2 completely. A catalytic combustion reaction mechanism was proposed： the Ce0.7Zr0.3O2 was reduced to Ce0.7Zr0.3O2-x by the reaction with carbon and then it was recovered to Ce0.7Zr0.3O2-x by the interaction with O2.     

Preparation of Well Dispersed and Ultra-Fine Ce （Zr）O2 Mixed Oxide by Mechanochemical Processing

Ultra-fine CeO2-ZrO2 mixed oxide was successfully synthesized by wet-solid phase mechanochemical processing, Ce2(CO3)3·8H2O, ZrOCl2·xH2O and ammonia were used as reactants. It is found that the crystalline Ce2(CO3)3·8H2O and ZrOCl2·xH2O are changed to amorphous cerium and zirconium hydroxide precursor after milling with ammonia, and Ce0.15Zr0.85O2 mixed oxide with pure tetragonal phase structure and medium particle size(D50)less than 1μm is formed by calcining precursor over 673 K. The XRD patterns indicate that the crystal unite size increases with rising calcining temperature due to crystal growth. However, the particle size and BET surface area of the Ce(Zr)O2 mixed oxide decreases with rising calcining temperature, which may be attributed to the contract of particles and the vanish of holes inside grains.     

Effect of different mixing ways in palladium/ceria-zirconia/alumina preparation on partial oxidation of methane

The effect of the mixing ways of Ce0.7Zr0.3O2-Al2O3 mixed oxides on the partial oxidations of methane （POM） was investigated over Pd/Ce0.7Zr0.3O2-Al2O3 catalysts, the mixing ways including salt precursor mixing （ATOM）, precipitator mixing （MOL）, and powder mechanically mixing （MECH）, respectively. The test results indicated that among the three samples, Pd/ATOM had the best catalytic activity while Pd/MOL had the best stability in the stability test. Both the activity sequences of the fresh and used samples were consistent with the order of Pd dispersion. According to the X-ray diffraction （XRD） and BET characterization, the interaction of Ce^4＋, Zr^4＋, and Al^3＋ in the ATOM mixed oxide was in favor of performing higher catalytic activity and thermal stability. The stability test indicated that Pd/MOL had the highest Pd dispersion and least coke formation on the active sites calculated by the Hz-chemisorption and TG results, which was considered to relate to its superior activity of POM to other catalysts.     

Synthesis kinetics and thermophysical properties of La_2（Zr_（0.7）Ce_（0.3））_2O_7 ceramic for thermal barrier coatings

La2(Zr0.7Ce0.3)2O7 (LZ7C3) ceramic was synthesized by solid state reaction with La2O3, ZrO2 and CeO2 as starting materials. The synthesis kinetics, phase structure, mass loss and microstructure were studied by thermo gravimetric-different thermal analyzer (TG-DTA), X-ray difference (XRD) and scanning electron microscopy (SEM). The thermal conductivity and thermal expansion coefficient were measured by laser-flash method and pushing-rod method, respectively. XRD results showed that LZ7C3 was a mixture of La2Zr2O7 (LZ, pyro- chlore) and La2Ce2O7 (LC, fluorite). The lowest synthesis temperature and time of LZ7C3 were 1400 oC and 5 h. There were no peaks of La2O3 when the powder granularity was about 0.82 μm in the synthesis process. The atom ratio La:Zr:Ce of prepared LZ7C3 powder was very close to 10:7:3 which was the theory value of LZ7C3. The thermal conductivity of LZ7C3 decreased gradually with the temperature increased up to 1200 oC, and was located within 0.79 to 1.02 W/(m·K), which was almost 50% lower than that of LZ, whereas its thermal expansion coefficient was larger and the value was 11.6×10-6 K-1.     

Surface and Texture Properties of Tb-Doped Ceria-Zirconia Solid Solution Prepared by Sol-Gel Method

The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.     

Preparation, characterization and catalytic properties of S2O82-/ZrOe-CeO2 solid superacid catalyst

A novel solid superacid catalyst S2O82-/ZrO2-CeO2 was prepared by a coprecipitation method and characterized by means of XRD, FTIR, BET, TEM and DSC/TG analysis methods. The results indicated that incorporation of appropriate amounts of Ce into the catalyst was beneficial to the formation of sole tetragonal ZrO2 and effectively prevented from the formation of monoclinic ZrO2, and restrained the loss of sulfated species. XRD revealed the presence of tetragonal Ceo0.16Zr0.84O2phase in the case of S2O82-/ZrO2-CeO2 calcined above 500 ℃. Catalytic activities of S2O82-/ZrO2-CEO2 for the estefification of lactic acid with n-butanol was studied. The results showed that the optimttrn conditions were as follows: calcination temperature of the catalyst 600 ℃, n(lactic acid):n(n-butyl alcohol)=1.0:3.0, w(S2O82-/ZrO2-CEO2)=12.0%, reaction temperature 145 ℃, and reaction time 2 h. The esterification efficiency of lactic acid was about 96.6%.     

Rare Earth Doping Effects on Properties of Ceria-Zirconia Solid Solution

Ce0.6Zr0.3RE0.1O2(RE=Y, La, Pr, Tb)solid solutions were prepared by co-precipitation technique and characterized by a series of methods. XRD and FT-Raman results show that Ce0.6Zr0.3RE0.1O2 has cubic fluorite structure. The different dopant ion radii bring different effect on the cell parameter of Ce0.6Zr0.3RE0.1O2. The X-ray photoelectron spectroscopy (XPS) results show that the binding energy of Ce3d, Zr3d and O1s for Ce0.6Zr0.3RE0.1O2 rises compared with that for Ce0.6Zr0.4O2, indicating that dopant elements change chemistry environment of solid solutions which is available to improve redox performance. Compared with Pd/Ce0.6Zr0.4O2, doping Y and La does not change air/fuel (A/F) characteristic of TWCs, but doping Pr and Tb widens A/F operating window and makes HC, CO and NO have higher conversion. The light-off temperature of Pd/Ce0.6Zr0.3La0.1O2 is corresponding to that of Pd/Ce0.6Zr0.4O2. However, the light-off temperatures of Pd/Ce0.6Zr0.3M0.1O2 (M=Y, Pr, Tb) are lower than that of Pd/Ce0.6Zr0.4O2, which keep much lower after high temperature treatments. Among Pd/Ce0.6Zr0.3RE0.1O2, Pd/Ce0.6Zr0.3Tb0.1O2 represents wider A/F operating window, higher conversion, lower light-off temperature and better high-temperature resistance.     

Effect of cobalt doping on ceria-zirconia mixed oxide： Structural characteristics, oxygen storage/release capacity and three-way catalytic performance

The effect of Co doping on ceria-zirconia mixed oxides was investigated for Co 0.1 Ce 0.6 Zr 0.3 O x sample prepared by sol-gel method. The Pd-only three-way catalyst (TWC) was obtained by incipient wetness impregnation with 0.5 wt.% Pd loading. The structural and oxygen handling properties were analyzed by X-ray diffraction (XRD), H 2 -temperature programmed reduction (H 2 -TPR) and the dynamic oxygen storage capacity (DOSC). The introduction of Co into ceria-zirconia lattice strongly modified the mobility of oxygen and enhanced the DOSC performance. Pd-only TWC based on the Co 0.1 Ce 0.6 Zr 0.3 O x support exhibited superior activity for water-gas shift and steam reforming and amplified amplitude of stoichiometric window.     

Quaternary Oxide of Cerium, Terbium, Praseodymium and Zirconium for Three-Way Catalysts

Inthelastdecadethethree waycatalystshave beenremarkablyimproved.Oxygenstoragecapacity(OSC)ofthecatalystwasdeterminedbyTPR.The measuredvalueisactuallyapartoftheoxygentransfer capacity(OTC)offluorite typeoxidescontainingCe,and orPr,and orTb[1,2].Theseoxides,Ce1-x-y PrxTbyO2-δ(0≤x≤1,0≤y≤1,0≤δ≤0.5)can releasetheirlatticeoxygenwhenthetemperatureisin creasedunderdifferentoxygenpartialpressureinclud inghydrogenflow,buttheywillabsorboxygenfromits vicinityenvironmentwhenthetemperatureisde…     

Effect of Preparation Method on Surface Area and Crystalline Form of CeO2-ZrO2 Solid Solution

TheCeO2 ZrO2 solidsolutionisacrucialcompo nentinthethree waycatalysts(TWCs)usedtocatalyzethesimultaneouspurificationofCO ,HCandNOxfromanautomobileexhaust [1～ 3] .Besidesafeasiblecatalyticactivity ,itshouldhavehighthermalstabilityandoxygenstoragecapacity(OSC) .InordertogainhighperformanceCeO2 ZrO2 solidsolution ,varioustechniqueshavebeendeveloped .ItwasshownthataneffectofpreparationmethodonthesurfaceareaandcrystallineformofCeO2 ZrO2 isveryobvious .Intheearliestwork ,theCeO2 ZrO…     

Effect of CeO_2-ZrO_2 on Pt/C electrocatalysts for alcohols oxidation

The electrocatalytic activity and stability of Pt/C catalyst modified by using CeO_2-ZrO_2 mixed oxides for the alcohols electrochemical oxidation as probes were investigated. The catalyst samples were characterized by X-ray diffraction(XRD) and scanning electron microscopy(SEM). The electrochemical properties were measured by a three electrode system on electrochemical workstation(IVIUM). The results showed that the presence of CeO_2-ZrO_2 might be associated with the presence of Pt, which indicated that possibly there was synergistic effect between CeO_2-ZrO_2 and Pt nanoparticles. The electrocatalytic activity and stability of Pt-MO_x/C(M=Ce, Zr) for methanol and ethanol oxidation was better than that of Pt-CeO_2/C, which was attributed to that CeO_2-ZrO_2 composited oxides enhanced oxygen mobility and promoted oxygen storage capacity(OSC). Furthermore, the best performance was found when the molar ratio of CeO_2 to ZrO_2 was 2:1 for the oxidation of methanol and ethanol. The forward peak current density of Pt-MO_x/C(M=Ce, Zr, Ce:Zr=2:1) towards the methanol electrooxidation was about 3.8 times that of Pt-CeO_2/C. Pt-MO_x/C(M=Ce, Zr) appeared to be a promising and less expensive methanol oxidation anode catalyst.     

Effect of metal doping into Ce0.5Zr0.5O2 on catalytic activity of MnOx/Ce0.5-xZr0.5-xM0.2xOy/Al2O3 for benzene combustion

The research investigated the effect of doping two metals separately or together into Ce0.5Zr0.5O2 on the catalytic activity of MnOx/Ce0.5–xZr0.5–xM0.2xOy/Al2O3 (M=Y, Mn, Y and Mn) for catalytic combustion of benzene. The prepared catalysts were characterized by X-ray diffraction (XRD), surface area analysis, oxygen storage capacity (OSC), and H2-temperature programmed reduction (H2-TPR). Cata-lytic test was performed on a conventional fixed bed flow reactor. The characterization results revealed that Y and Mn ions entered into the ceria-zirconia mixed oxides framework, which improved the textural properties and greatly promoted the MnOx dispersion on the support surface. The complete conversion temperature of benzene on MnOx/Ce0.4Zr0.4Y0.1Mn0.1Oy /Al2O3 was 563 K, and the selectivity of carbon dioxides was 99%. This catalyst could be applied in a wide range of GHSV and wide concentration condition, showing great potential for application.