Silica–zirconia membranes for nanofiltration

Inorganic nanofiltration membranes were fabricated from silica–zirconia composite colloidal sol (molar ratio Si/Zr=9/1) using a sol–gel process. Molecular weight cut-off (MWCO) was successfully controlled between 200 and 1000 Da by regulating the colloidal diameters of sol solutions in the final coating stage. The pure water permeabilities ranged from 0.15×10⁻¹¹ to 1.5×10⁻¹¹ m³ m⁻² s⁻¹ Pa⁻¹. Pore size and pore size distribution were estimated based on the dynamic method of humid air permeation, and found to be from 1.0 to 2.9 nm. The MWCO obtained from NF experiments using neutral organic solutes corresponds well with the pore diameters estimated from the dynamic permeation method. Silica–zirconia membranes were found to be stable in aqueous solution for periods in excess of four months.     

A cost-effective and fast synthesis of nanoporous SiO2 aerogel powders using water-glass via ambient pressure drying route

Considering the need for large-scale production of silica aerogel powders, the present research was aimed to develop a simple, cost-effective and rapid process based on water-glass precursor via ambient pressure drying (APD) route. It has been shown that the surface chemical modification of hydrogels can rapidly be carried out with extremely low doses (e.g. 5 g of hexamethyldisilazane (HMDS) for 100 g of hydrogel) of HMDS by a co-precursor method which makes this process quite cost-effective. The surface modification in the aqueous phase essentially resulted in the displacement of the pore water and the simultaneous one-step solvent exchange using n-hexane converted the hydrogel into an organo-gel in 3 h and thus the total processing time of the aerogel powder production via APD could drastically be reduced to 5 h. The solvent n-hexane could be recollected during the drying stage and it does not add much to the material cost. The aerogel powders with tapping densities and specific surface areas in the range of 0.100–0.309 g/cm³ and 473–776 m²/g, respectively, could be synthesized using this novel route. The surface modification of the aerogel powders was explored by means of X-ray photoelectron spectroscopy (XPS) in conjunction with the Fourier transform infrared (FT-IR) spectroscopy. The textural investigations revealed that the aerogel powders with a wide variation in their pore size distributions and average pore diameters can easily be synthesized by varying the silica content in the sol.     

Synthesis of double mesoporous core-shell silica spheres with tunable core porosity and their drug release and cancer cell apoptosis properties

In this work, we demonstrate a simple two-pot approach to double mesoporous core–shell silica spheres (DMCSSs) with uniform size of 245–790 nm, shell thickness of 41–80 nm and surface area and total pore volume of 141–618 m² g^?1 and 0.14–0.585 cc g^?1, respectively. First, solid silica spherical particles were synthesized by the Stöber method and used as a core. Second, a mesoporous shell could be formed around the silica cores by using an anionic surfactant and a co-structure directing agent. It was found that mesopores can be anchored within dense silica cores during mesoporous silica shell formation, synchronously the base group with surfactant assistant can etch the dense silica cores to re-organize new mesostructure, so that double mesoporous core–shell silica sphere (DMCSS) structure can be obtained by a single surfactant-templating step. The spherical size and porosity of the silica cores of DMCSS together with shell thickness can be tuned by controlling Stöber parameters, including the concentrations of ammonia, solvent and tetraethoxysilane and the reaction time. DMCSS were loaded with ketoprofen and thymoquinone, which are an anti-inflammatory and a potential novel anti-cancer drug, respectively. Both drugs showed controlled release behavior from the pores of DMCSS. Drug uptakes within DMCSS were ～27 and 81 wt.% for ketoprofen and thymoquinone, respectively. Furthermore, DMCSS loaded with thymoquinone was more effective in inducing cancer cell apoptosis than uncontained thymoquinone, because of the slow release of the drug from the mesoporous structure.     

Hafnia ceramic nanofiltration membranes. Part I: Preparation and characterization

We have used a sol–gel process as an efficient method for the preparation of hafnia nanofiltration membranes. A stable colloidal sol was obtained after hydrolysis of an alkoxide and peptization of the hydrous oxide precipitate. After the drying of the sol, the hafnia powder was characterized using several methods, such as X-ray diffraction, dilatometry, thermal analysis, electrophoretic, and BET measurements. The hafnia membrane was obtained by coating the colloidal sol on a mesoporous ceramic support, followed by a drying and sintering of the gelled layer. The membrane was characterized by SEM and nitrogen adsorption–desorption to determine the pore size. The filtration properties of a hafnia membrane sintered at 450°C were determined using water permeability and rejection of solutions containing sucrose, polyethylene glycols of different molecular weights (400, 600, 1000) and salt solutions. This membrane is characterized by a MWCO of 420 Da and pore size near 1 nm.     

Epoxy-functionalized large-pore SBA-15 and KIT-6 as affinity chromatography supports

Mesoporous silica supports are proposed as an alternative to polymeric stationary phases for fast affinity chromatography due to their better mechanical strength compared to polymers. Ideal supports should combine high surface area and large pore size to allow a high loading capacity of large molecules, such as proteins, and favor their accessibility. Increasing the pore size of large-surface area micelle-templated silicas (SBA-15, KIT-6) has been achieved by swelling the micelles by the addition of organic molecules and increasing synthesis time and temperature. The pore size of hexagonal silica mesostructured SBA-15 has been increased up to 35 nm. These materials could find therefore application as affinity chromatography for immunoextraction.     

Synthesis and characterization of high surface area TiO2/SiO2 mesostructured nanocomposite

Recently titania synthesis was reported using various structuration procedures, leading to the production of solid presenting high surface area but exhibiting moderate thermal stability. The study presents the synthesis of TiO₂/SiO₂ nanocomposites, a solid that can advantageously replace bulk titania samples as catalyst support. The silica host support used for the synthesis of the nanocomposite is a SBA-15 type silica, having a well-defined 2D hexagonal pore structure and a large pore size. The control of the impregnation media is important to obtain dispersed titania crystals into the porosity, the best results have been obtained using an impregnation in an excess of solvent. After calcination at low temperature (400 °C), nanocomposites having titania nanodomains (～2–3 nm) located inside the pores and no external aggregates visible are obtained. This nanocomposite exhibits high specific surface area (close to that of the silica host support, even with a titania loading of 55 wt.%) and a narrow pore size distribution. Surprisingly, the increase in calcination temperature up to 800 °C does not allow to detect the anatase to rutile transition. Even at 800 °C, the hexagonal mesoporous structure of the silica support is maintained, and the anatase crystal domain size is evaluated at ～10 nm, a size close to that of the silica host support porosity (8.4 nm). Comparison of their physical properties with the results presented in literature for bulk samples evidenced that these TiO₂/SiO₂ solids are promising in term of thermal stability.     

Ptshell–Aucore/C electrocatalyst with a controlled shell thickness and improved Pt utilization for fuel cell reactions

Nanoscale Pt_shell–Au_core/C with a controlled shell thickness was successfully synthesized based on a successive reduction strategy. With a Au core size of 4.8 nm, a complete Pt shell of thickness ∼0.6 nm was formed at Pt/Au mole ratio 1:1. The complete coverage of Au core with Pt shell was suggested by various techniques including TEM, UV–vis and cyclic voltammetry. A higher specific activity compared to conventional Pt/C was demonstrated using the probe reaction of methanol electro-oxidation, proving the improved Pt utilization with this core-shell structure.     

Preparation and properties of silica–gold core–shell particles

Silica-metal core–shell particles, as for instance those having siliceous core and nanostructured gold shell, attracted a lot of attention because of their unique properties resulting from combination of mechanical and thermal stability of silica and magnetic, electric, optical and catalytic properties of metal nanocrystals such as gold, silver, platinum and palladium. Often, the shell of the core–shell particles consists of a large number of metal nanoparticles deposited on the surface of relatively large silica particles, which is the case considered in this work. Namely, silica particles having size of about 600 nm were subjected to surface modification with 3-aminopropyltrimethoxysilane. This modification altered the surface properties of silica particles, which was demonstrated by low pressure nitrogen adsorption at ?196 °C. Next, gold nanoparticles were deposited on the surface of aminopropyl-modified silica particles using two strategies: (i) direct deposition of gold nanoparticles having size of about 10 nm, and (ii) formation of gold nanoparticles by adsorption of tetrachloroauric acid on aminopropyl groups followed by its reduction with formaldehyde.The overall morphology of silica–gold particles and the distribution of gold nanoparticles on the surface of modified silica colloids were characterized by scanning electron microscopy. It was shown that direct deposition of colloidal gold on the surface of large silica particles gives more regular distribution of gold nanopartciles than that obtained by reduction of tetrachloroauric acid. In the latter case the gold layer consists of larger nanoparticles (size of about 50 nm) and is less regular. Note that both deposition strategies afforded silica–gold particles having siliceous cores covered with shells consisting of gold nanoparticles of tunable concentration.     

Surface silylation and pore structure development of silica aerogel composites from colloid and TEOS-based precursor

Flexible aerogel-fiber composites were prepared by silylation and ambient drying of colloidal silica and tetraethylorthosilicate (TEOS)-based sol. After immersing glass fiber matrices into silica sol with colloid-based, colloid/TEOS-based, and TEOS-based silica sol, it was surface-modified in a trimethylchlorosilane/n-hexane solution and heat-treated at 230 °C in ambient atmosphere. Surface silylation of silica aerogel synthesized from colloid and TEOS-based silica sols showed different behaviors. For colloid silica gel, it was comprised of small sized mesopores because colloid-based silica gel has dense networks through great degrees of hydrolysis and condensation. On the contrary, TEOS-based aerogel was consisted of relatively large-sized pores because of comparatively lesser degree of hydrolysis and condensation. Through this study, we can know that the pore structures of silica aerogel could be controlled by choosing colloid or TEOS-based precursor and surface silylation reaction.     

Design and characterization of Ni2+ and Co2+ decorated Porous Magnetic Silica spheres synthesized by hydrothermal-assisted modified-Stöber method for His-tagged proteins separation

The complete elimination of enzymes from the reaction mixture and the possibility of its recycling for several rounds result in great benefits, allowing the reduction of the enzyme consumption and their usability in continuous processes. In this work, it is evaluated the capture of a H6-tagged green fluorescence protein (GFP-H6) on porous magnetic spheres using the Co²⁺ and Ni²⁺ affinity adsorption as a possible cost-effective and up-scaled alternative way for the immobilization of His-tagged proteins. For this purpose, Porous Magnetic Silica (PMS) spheres were synthesized by one-step hydrothermal-assisted modified-Stöber method. The obtained spheres have a homogenous size distribution of 400 nm diameter. The γ-Fe₂O₃ nanoparticles are homogenously distributed in the silica matrix. The obtained PMS spheres have a saturation magnetization of about 10 emu/g. Magnetophoresis measurements show a total separation time of 16 min at 60 T/m. The obtained PMS spheres were successfully and homogenously decorated with Co²⁺ and Ni²⁺ and then evaluated for the capture of a GFP-H6 protein. The results were compared with the performance of the commercial beads Dynabeads® His-Tag Isolation &; Pulldown.     

High capacity organic monoliths for the simultaneous application to biopolymer chromatography and the separation of small molecules

A method for controlling the mesoporous structure of monolithic organic copolymers is presented by systematic variation in polymerisation time, employing poly(p-methylstyrene-co-1,2-(p-vinylphenyl)ethane) (MS/BVPE) as a representative styrene system. Decreasing the time of polymerisation introduces a considerable fraction of mesopores (up to 20% of the total pore volume), while keeping the support permeability reasonable high (～1.3 × 10^?14 m²). Monolith structures, prepared in such a manner, enable efficient (typically around 70,000 plates/m) and fast separation of low-molecular-weight compounds, whereas their performance towards biopolymers is comparable to column supports, fabricated according to typically used protocols (polymerisation time >12 h and thus monomer conversion >98%). The polymerisation time is hence a valuable tool to tailor the fraction of support flow-channels, macropores as well as mesopores, which is shown dramatically to influence the chromatographic separation characteristics of the respective column. This way, the preferred applicability of organic (styrene) monolithic copolymers can be extended to the separation of small molecules beyond biopolymer chromatography.     

A comparison of lipase and trypsin encapsulated in mesoporous materials with varying pore sizes and pH conditions

Immobilized enzymes have an advantage over enzymes free in solution in that they are easily recovered after completed reaction. In addition, immobilization often gives enhanced stability. Entrapment of an enzyme in the pores of a mesoporous material is an attractive procedure since the enzyme is immobilized without any covalent bonding to a support which may be detrimental to the catalytic performance. The objective of this work is to compare the encapsulation and catalytic performance of lipase from Mucor miehei and trypsin from bovine pancreas, two hydrolases with rather dissimilar properties and structures. We also demonstrate the importance of the pore dimensions and the pH for proper function of the encapsulated enzyme. Mesoporous silica particles (SBA-15) with three different pore sizes (50 Å, 60 Å and 89 Å) were synthesized and hexagonal structures with narrow pore size distributions were confirmed with TEM, SAXS and N₂-adsorption. Lipase and trypsin were encapsulated separately in the silica particles and the results indicate distinct differences between the two enzymes, both in loading capacity and catalytic activity. For trypsin the encapsulation rate and the loading capacity were large with a maximum reached at pH 7.6. The largest product yield was obtained with the particles with 60 Å pores, however, the yield was significantly lower than with free trypsin. For lipase optimal encapsulation rate and loading capacity were reached with the particles with 89 Å pores at pH 6.0 but were low compared to trypsin. However, the catalytic activity of the encapsulated lipase was more than twice as large as for free lipase, which can be explained by an interfacial activation of lipase at the silica surface.     

Structural and spectroscopic studies of LaPO4:Ce/Tb@LaPO4@SiO2 nanorods: Synthesis and role of surface coating

Highly fluorescent LaPO₄:Ce/Tb@LaPO₄@SiO₂ (core/shell/Si) nanorods(NRs) were fabricated with an average length 100 nm by co-precipitation process at low temperature. X-ray diffraction (XRD), Transmission electron microscopy (TEM), energy dispersive X-ray analysis, Fourier transform infrared, optical absorption and photoluminescence spectral techniques were applied to investigate the crystal structure, phase purity, morphology, surface chemistry and optical properties of the as-prepared samples. XRD results confirmed the formation of highly crystalline with single phase, monoclinic type structure. TEM image illustrates the poly-dispersed, narrow size distributed, irregular size rod-shaped nanostructures, with mean diameters of 20 nm and average lengths up to 140 nm. FTIR spectral analysis confirmed the silica surface modification. The comparative emission spectral study shows highest luminescence intensity of core/shell NRs, due to a reduction in nonradiative transition rate. The emission intensity enhancement proves that growing of an inert LaPO₄ layer on the surface of luminescent core-NRs was an effective way to suppress surface related quenching mechanism. These well crystalline, highly aqueous soluble along with extraordinary colloidal stability core/shell/Si NRs were extremely suitable material in fluorescent bio-labeling applications.     

Role of core diameter and silica content in photocatalytic activity of TiO2/SiO2/Fe3O4 composite

Magnetically separable TiO₂/SiO₂/Fe₃O₄ composites of different core (Fe₃O₄) diameters and silica contents have been prepared by sol–gel technique for both silica and titania coatings. Energy dispersive X-ray fluorescence (EDX), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), BET surface area analysis and scanning electron microscope (SEM) have been used for characterization of prepared samples. Photocatalytic activity of the prepared samples has been investigated by photodegradation of methyl orange. Obtained results have shown that 25–45 μm core diameter exhibits the maximum activity since it possesses a convenient surface area and light transmittance. Silica content has a significant effect on the activity of composite. Silica content of more than 10 wt% has reduced the catalyst activity because of the increase in particle diameter and reduction of surface area.     

Silica–silver core–shell particles for antibacterial textile application

The silica–silver core–shell particles were synthesized by simple one pot chemical method and were employed on the cotton fabric as an antibacterial agent. Extremely small (1–2 nm) silver nanoparticles were attached on silica core particles of average 270 nm size. The optimum density of the nano silver particles was found which was sufficient to show good antibacterial activity as well as the suppression in their surface plasmon resonance responsible for the colour of the core–shell particle for antibacterial textile application. The change in the density and size of the particles in the shell were monitored and confirmed by direct evidence of their transmission electron micrographs and by studying surface plasmon resonance characteristics. The colony counting method of antibacterial activity testing showed excellent results and even the least silver containing core–shell particles showed 100% activity against bacterial concentration of 10⁴ colony counting units (cfu). The bonding between core–shell particles and cotton fabric was examined by X-ray photoelectron spectroscopy. The antibacterial activity test confirmed the firm attachment of core–shell particles to the cotton fabric as a result 10 times washed sample was as good antibacterial as that of unwashed sample. The bacterial growth was inhibited on and beneath the coated fabric, at the same time no zone of inhibition which occurs due to the migration of silver ions into the medium was observed indicating immobilization of silver nanoparticles on silica and core–shell particles on fabric by strong bonding.     

The effect of silver doping on photocatalytic properties of titania multilayer membranes

In this investigation an Ag doped titania multilayer membrane is successfully fabricated via the sol–gel processing method. The doped membrane is characterized via X-ray Diffraction and N₂-sorption techniques and the photocatalytic properties of the membrane are investigated via methyl orange degradation. The properties included high surface area (101 m²/g), small pore size (3.1 nm), and active anatase crystal phase. The prepared titania membrane has a high photocatalytic activity and decomposes methyl orange by 50% after 9 h of UV irradiation. The prepared membrane can be applied in the development of efficient photocatalytic systems for the treatment of water. Due to the high photoactivity of the prepared titania membrane, this study reveals the possibility of combining two processes for removal of organic pollutants: the photocatalytic process and the membrane separation process. In the combining process the lifetime of the membrane increases and the quality of water is enhanced.     

Trimodel hierarchical yolk-shell porous materials TS-1@mesocarbon:Synthesis and catalytic application

Trimodal hierarchical yolk-shell materials consisting of TS-1 core and mesoporous carbon shell(YS-TS-1@MC) was successfully synthesized by using TS-1@mesosilica as hard template,sucrose as carbon source and organic base tetrapropylammonium hydroxide(TPAOH) as silica etching agent.The resultant YS-TS-1@MC contains the micropores(0.51 nm) in TS-1 core,the mesopores(2.9 nm) in carbon shell as well as a void or a stack pore between TS-1 fragcments(TS-1 intercrystal mesopores,～18.4 nm).Under the rigorous etching conditions,the crystalline structure of TS-1 core was well retained.The YS-TS-1@MC served as a good support for palladium nano-particles(Pd NPs) or Rh(OH)x species,giving rise to efficient bifunctional catalysts for the tandem reactions including one-pot synthesis of propylene oxide or amides.     

Stability and performance of porous silica–zirconia composite membranes for pervaporation of aqueous organic solutions

Porous silica–zirconia membranes were fabricated by the sol–gel techniques to study their stability against water and the pervaporation performance of aqueous solutions of organic solvents. Zirconia (10–70 mol%) was added to silica to obtain silica–zirconia composite membranes by firing at 400–500 °C for pervaporation tests with organic solvent/water mixtures, such as iso-propyl alcohol (IPA)/water and tetrahydrofuran (THF)/water mixtures at their normal boiling points.The membrane coatings have been done effectively by the hot-coating methods proposed previously. Boiling water treatments introduced in the coating processes have made the membranes quite stable even in the high water concentration region of aqueous organic solutions at their normal boiling points. Zirconia contents larger than about 40 mol% have made the silica–zirconia membranes quite stable. The membranes of zirconia contents less than about 30 mol% were found not stable in a dilute aqueous solution of IPA. The membranes fabricated by the conventional dip-coating methods with slow drying were not stable against water because of the probable segregation of silica and/or silica-rich phases during drying.The membranes fired at lower temperature (400 °C) gave a higher water flux of around 500 mol m⁻² h⁻¹ (9 kg m⁻² h⁻¹) with a separation factor larger than 1500 at 10 wt.% of water in the boiling feed of IPA/water mixture, for example.     

Crystal structure,electrical conductivity,thermal expansion and compatibility studies of Co-substituted lanthanum strontium manganite system

La_0.76Sr_0.19Mn_1?xCo_xO_3±δ, LSMCo_x (0 ≤ x ≤ 1) perovskite oxides were synthesized by conventional ceramic route. The effect of Co substitution for Mn on the crystal structure, electrical conductivity and thermal expansion properties was investigated. XRD indicated rhombohedral symmetry for the studied compositions at 1673 K. The lattice parameters so determined showed significant reduction in cell volume, which is attributed to smaller ionic radii of Co³⁺ ions. The results of electrical conductivity data indicated that the conductivity mechanism is by thermally activated hopping of small polarons between localized states corresponding to Mn or Mn and Co sites of different valence value. The conductivity decreases at all temperatures up to 40 mol% Co substitution while the energy of activation increases. This is possibly due to an increase in Jahn–Teller distortion, at an extent higher than the increase of the concentration of charge carriers. Thermal expansion coefficient values in the series increase with increasing Co content which has been explained on the basis of the changes in the spin states of the Co ions and the consequent changes in the ionic size with temperature. Solution route synthesis produces fine-size particles with better properties, consequently one composition from the above having enhanced requisite properties, viz. La_0.76Sr_0.19Mn_0.8Co_0.2O_3±δ was synthesized by sol–gel route. The sol–gel synthesized compound had crystallite size of ～30 nm at 1173 K obtained using Scherrer's equation. Thus the potential of these compounds as cathodes for solid oxide fuel cells (SOFCs) have been evaluated.As Ce_0.8RE_0.2O_2?δ (RE = Sm, Gd) are being investigated for their use as electrolytes in SOFCs, their mechanical compatibility as well as chemical compatibility with the potential cathode material from the above LSMCo_x series was also studied.     

Microstructural and gas separation properties of CVD modified mesoporous γ-alumina membranes

Chemical vapor deposition (CVD) was used to modify 4 nm pore, sol–gel derived, γ-alumina membranes supported on macroporous α-alumina. Aluminum oxide was deposited in the pores of the γ-alumina membrane by alternating additions of trimethylaluminum (TMA) and water vapor. By reducing the pore size, the permeance of non-condensable gasses was reduced much more than the permeance of condensable gasses due to capillary condensation or preference adsorption of water vapor. The modified membrane that exhibited the best separation properties had a water vapor permeance ranging from 1.5×10⁻⁶ to 3.0×10⁻⁷ mol/m² s Pa, an oxygen permeance ranging from 1.7×10⁻⁷ to 1.5×10⁻⁹ mol/m² s Pa, and a separation factor as high as 140 at room temperature. The microstructure of the pores contained some irregularities which were attributed to an atomic layer CVD (ALCVD) mechanism modified by homogeneous reactions. The effect of the modified ALCVD was higher permeances than would be expected. P-type zeolite membranes were also made and found to have similar separation properties to the more heavily modified γ-alumina membranes.