Quenched and Partitioned Microstructures Produced <Emphasis Type="Italic">via</Emphasis> Gleeble Simulations of Hot-Strip Mill Cooling Practices

Previous researchers reported on quenched and partitioned (Q&P) microstructures produced via carbon partitioning from martensite into austenite during isothermal annealing after quenching to develop a partially martensitic initial structure. However, the thermal profile used in previous studies is not well suited to creating Q&P microstructures directly from a hot-strip mill. In this work, the commonly employed Q&P thermal profile (i.e., having an isothermal partitioning step) was modified to evaluate nonisothermal partitioning that might instead occur during cooling of a wound coil. Thus, it was possible to assess the potential for creating Q&P microstructures and properties directly off of the hot mill. Gleeble thermal simulations representative of a hot-strip mill cooling practice were used to create dual-phase, Q&P, transformation-induced plasticity (TRIP), and conventional microstructures by varying the quench/coiling temperatures (CTs) using a 0.19C-1.59Mn-1.63Si (wt pct) steel. Microstructural and mechanical property data indicate that hot rolling might be a viable processing route for high-strength Q&P steels.     

Toughness Improvement in a Novel Martensitic Stainless Steel Achieved by Quenching–Tempering and Partitioning

In the present work, a novel medium carbon martensitic stainless steel (MCMSS) with an excellent combination of strength, ductility, and impact toughness was designed on the basis of quenching-tempering and partitioning (Q–T&P) technology. Q–T&P is an identical heat treatment with a standard quenching and tempering (Q–T) process but has the same role with quenching and partitioning (Q&P) on microstructure control, i.e., promoting carbon-rich retained austenite via inhibiting carbide precipitation. Results show that, without compromise on strength, the total elongation and room temperature impact toughness, i.e., 9.6 pct and 90 J cm⁻², of the proposed alloy (23Cr13MnSi) increase by 14 and 110 pct, respectively, as compared to those of the commercial AISI 420. The significant improvement of ductility and impact toughness in the proposed alloy is mainly a result of the gradual transformation induced plasticity (TRIP) effects, which are caused by carbon-rich retained austenite with heterogeneous stability and carbide-free martensite formed in the Q–T&P process.

     

Overview of Mechanisms Involved During the Quenching and Partitioning Process in Steels

The application of the quenching and partitioning (Q&P) process in steels involves a microstructural evolution that is more complex than just the formation of martensite followed by carbon partitioning from martensite to austenite. Examples of this complexity are the formation of epitaxial ferrite during the first quenching step and the formation of bainite, carbides, and carbon gradients as well as migration of martensite/austenite interfaces during the partitioning step. In this work, recent investigations on the mechanisms controlling microstructural changes during the application of the Q&P process are evaluated, leading to phase-formation based concepts for the design of Q&P steels.     

On the role of Manganese Partitioning in Metastable Austenite by Quenching and Partitioning Treatment

With the aim to study the role of “frozen” concentration gradient of manganese (Mn) element in stability of retained austenite (RA) with multiple-stage martensite transformation, a series of intercritical annealing (IA) temperatures is conducted before quenching and partitioning (Q&P) treatment. Morphology and distribution of RA are observed by field emission gun scanning electron microscope and electron back-scatter diffraction. The volume fraction (7%–16%) and stability of metastable RA is found to be affected profoundly by IA temperature. Thermodynamic and kinetic analysis are conducted to elucidate the evolution of RA in process of IAQP treatment. The predicted levels of RA are in good accordance with measurements. It is found that the inhomogeneous partitioning of Mn in period of IA, combining with the incomplete partitioning of carbon during Q&P, radically regulated the Q&P microstructure. The incomplete partitioning of carbon in RA, with excess carbon segregation at dislocations and boundaries, lead to partition-less bainite transformation owing to the average carbon content in RA lower than the “T_o” threshold.     

Microstructure Evolution and Mechanical Behavior of a CMnSiAl TRIP Steel Subjected to Partial Austenitization Along with Quenching and Partitioning Treatment

The present study investigated the microstructure evolution and mechanical behavior in a low carbon CMnSiAl transformation-induced plasticity (TRIP) steel, which was subjected to a partial austenitization at 1183 K (910 °C) followed by one-step quenching and partitioning (Q&P) treatment at different isothermal holding temperatures of [533 K to 593 K (260 °C to 320 °C)]. This thermal treatment led to the formation of a multi-phase microstructure consisting of ferrite, tempered martensite, bainitic ferrite, fresh martensite, and retained austenite, offering a superior work-hardening behavior compared with the dual-phase microstructure (i.e., ferrite and martensite) formed after partial austenitization followed by water quenching. The carbon enrichment in retained austenite was related to not only the carbon partitioning during the isothermal holding process, but also the carbon enrichment during the partial austenitization and rapid cooling processes, which has broadened our knowledge of carbon partitioning mechanism in conventional Q&P process.     

Evaluation of Carbon Partitioning in New Generation of Quench and Partitioning (Q&P) Steels

Quenching and partitioning (Q&P) and a novel combined process of hot straining (HS) and Q&P (HSQ&P) treatments have been applied to a TRIP-assisted steel in a Gleeble®3S50 thermomechanical simulator. The heat treatments involved intercritical annealing at 800 °C and a two-step Q&P heat treatment with a partitioning time of 100 seconds at 400 °C. The “optimum” quench temperature of 318 °C was selected according to the constrained carbon equilibrium (CCE) criterion. The effects of high-temperature deformation (isothermal and non-isothermal) on the carbon enrichment of austenite, carbide formation, and the strain-induced transformation to ferrite (SIT) mechanism were investigated. Carbon partitioning from supersaturated martensite into austenite and carbide precipitation were confirmed by means of atom probe tomography (APT) and scanning transmission electron microscopy (STEM). Austenite carbon enrichment was clearly observed in all specimens, and in the HSQ&P samples, it was significantly greater than in Q&P, suggesting an additional carbon partitioning to austenite from ferrite formed by the deformation-induced austenite-to-ferrite transformation (DIFT) phenomenon. By APT, the carbon accumulation at austenite/martensite interfaces was observed, with higher values for HSQ&P deformed isothermally (≈ 11 at. pct), when compared with non-isothermal HSQ&P (≈ 9.45 at. pct) and Q&P (≈ 7.6 at. pct). Moreover, a local Mn enrichment was observed in a ferrite/austenite interface, indicating ferrite growth under local equilibrium with negligible partitioning (LENP).

     

Development of Multiphase Microstructure with Bainite, Martensite, and Retained Austenite in a Co-Containing Steel Through Quenching and Partitioning (Q&P) Treatment

The quenching and partitioning (Q&P) treatment of steel aims to produce a higher fraction of retained austenite by carbon partitioning from supersaturated martensite. Q&P studies done so far, relies on the basic concept of suppression of carbide formation by the addition of Si and/or Al. In the present study Q&P treatment is performed on a steel containing 0.32 C, 1.78 Mn, 0.64 Si, 1.75 Al, and 1.20 Co (all wt pct). A combination of 0.64 Si and 1.75 Al is chosen to suppress the carbide precipitation and therefore, to achieve carbon partitioning after quenching. Addition of Co along with Al is expected to accelerate the bainite transformation during Q&P treatment by increasing the driving force for transformation. The final aim is to develop a multiphase microstructure containing bainite, martensite, and the retained austenite and to study the effect of processing parameters (especially, quenching temperature and homogenization time) on the fraction and stability of retained austenite. A higher fraction of retained austenite (~13 pct) has indeed been achieved by Q&P treatment, compared to that obtained after direct-quenching (2.7 pct) or isothermal bainitic transformation (9.7 pct). Carbon partitioning during martensitic and bainitic transformations increased the stability of retained austenite.     

Enhancement of the Mechanical Properties of a V–Ti–N Microalloyed Steel Treated by a Novel Precipitation-Quenching & Partitioning Process

In this study, a novel precipitation-quenching & partitioning (P-Q&P) process was proposed by combining a proper intermediate holding treatment with the Q&P process, which successfully increased the strength of a V–Ti–N microalloyed steel without sacrificing the plasticity. However, the impact toughness of the P-Q&P samples is lower than that of the Q&P sample. Compared to the Q&P sample, the P-Q&P samples have more retained austenite. In addition, coarser substructures of martensite and bainite were formed in the P-Q&P samples. All the P-Q&P and Q&P samples contain two types of carbonitrides, which are the large-size particles (enriched in Ti) formed or undissolved in austenite and the small-size particles (enriched in V) formed in martensite and bainite. The P-Q&P samples have a smaller size and larger volume fraction of the large-size particles than the Q&P sample. The increase in the strength of the P-Q&P samples is attributed to the precipitation strengthening of the carbonitrides formed in austenite during the intermediate holding treatment. And the maintained elongation is mainly caused by the higher austenite content in the P-Q&P samples. The poor toughness of the P-Q&P samples is mainly resulted from the coarser substructures.

     

Effect of Interfacial Mn Partitioning on Carbon Partitioning and Interface Migration During the Quenching and Partitioning Process

A so-called QP-LE model, in which interface condition is assumed to be Local Equilibrium (LE), has been proposed to evaluate the effect of interfacial Mn partitioning on interface migration and carbon partitioning during the Quenching and partitioning process (Q&P) of an Fe-0.3C-3.0Mn-1.5Si (wt pct) alloy. The predictions by the QP-LE model are compared with those by the conventional QP-PE model in which interface condition is assumed to be Paraequilibrium (PE). It is found that interfacial partitioning of Mn plays a significant role in carbon partitioning and the martensite/austenite interface migration during the Q&P process.     

Application of Quenching and Partitioning (Q&P) Processing to Press Hardening Steel

Press hardening steel (PHS) has been increasingly used for the manufacture of structural automotive parts in recent years. One of the most critical characteristics of PHS is a low residual ductility related to a martensitic microstructure. The present work proposes the application of quenching and partitioning (Q&P) processing to improve the ductility of PHS. Q&P processing was applied to a Si- and Cr-added Q&P-compatible PHS, leading to a press hardened microstructure consisting of a tempered martensite matrix containing carbide-free bainite and retained austenite. The simultaneous addition of Si and Cr was used to increase the retained austenite fraction in the Q&P-compatible PHS. The Q&P processing of the PHS resulted in a high volume fraction of C-enriched retained austenite, and excellent mechanical properties. After a quench at 543 K (270 °C) and a partition treatment at 673 K (400 °C), the PHS microstructure contained a high volume fraction of retained austenite and a total elongation (TE) of 17 pct was achieved. The yield strength (YS) and the tensile strength were 1098 and 1320 MPa, respectively. The considerable improvement of the ductility of the Q&P-compatible PHS should lead to an improved in-service ductility beneficial to the passive safety of vehicle passengers.     

Investigation into Competitive Mechanism of Carbon Partitioning and Pseudospinodal Decomposition of Supersaturated Martensite in Q&P Steel Containing High Silicon

In this study, the competing mechanisms of carbon partitioning and concurrent pseudospinodal decomposition of supersaturated martensite, forming superlattice-ordered α″-Fe₁₆C₂, are elucidated in a quenching and partitioning (Q&P) steel containing high silicon based on various microstructural characterizations. Our results demonstrate that the fluctuation of carbon content caused by high-density dislocations and transformation residual stress in martensite may stimulate the pseudospinodal decomposition. Furthermore, the sluggish diffusion kinetics of silicon and nickel inhibits further transformation from α″-Fe₁₆C₂ to carbide precipitation. The experimental results provide new insights into the pseudospinodal decomposition and carbon redistribution mechanism during the carbon partitioning process.

     

Effect of welding consumables and processes on dynamic fracture toughness (J 1d) of armour grade Q&T steel joints

Abstract

Austenitic stainless steel (ASS) welding consumables are being used for welding armour grade Q&T steels, as they have higher solubility for hydrogen in the austenitic phase, to avoid hydrogen induced cracking (HIC). Even with austenitic stainless steel consumables under high dilution, the risk of HIC prevailed. In recent years, the developments of low hydrogen ferritic steel (LHF) consumables that contain no hygroscopic compounds are utilised for welding Q&T steels. The use of ASS fillers for welding armour grade Q&T steels creates a duplex microstructure (austenite and δ ferrite) in the welds, which drastically reduces the joint efficiency (ratio of ultimate tensile strength of the joint and the base metal). On the other hand, the weld made using LHF fillers exhibited superior joint efficiency due to the preferential ferrite microstructure in the welds. The use of ASS and LHF consumables for armour grade Q&T steels will lead to formation of distinct microstructures in their respective welds. This microstructural heterogeneity will have a drastic influence on the dynamic fracture toughness of the armour grade Q&T steel welds. Hence, in this investigation an attempt has been made to study the influence on the welding consumables and processes on the dynamic fracture toughness properties of armour grade Q&T steel joints. Shielded metal arc welding (SMAW) and flux cored arc welding (FCAW) processes were used for fabrication of the joints using ASS and LHF welding consumables. The joints fabricated by SMAW process using ASS consumables exhibited superior dynamic fracture toughness values compared to all other joints.     

Benefits of Intercritical Annealing in Quenching and Partitioning Steel

Compared to the quenching and partitioning (Q&P) steel produced by full austenization annealing, the Q&P steel produced by the intercritical annealing shows a similar ultimate tensile stress but a larger tensile ductility. This property is attributable to the higher volume fraction and the better mechanical stability of the retained austenite after the intercritical annealing. Moreover, intercritical annealing produces more ferrite and fewer martensite phases in the microstructure, making an additional contribution to a higher work hardening rate and therefore a better tensile ductility.     

双相区形变对含Cu低碳钢Cu配分行为及组织性能影响

采用双相区形变+IQP及IQP(双相区等温-奥氏体化-淬火-碳配分)热处理工艺,研究了双相区形变对一种含Cu低碳钢Cu配分行为及其组织性能的影响。采用电子探针(EPMA)、扫描电镜(SEM)及透射电镜(TEM)等手段对元素配分行为及组织演变进行了表征。结果表明:实验钢经2种工艺处理后均出现Cu元素向逆转奥氏体的配分行为,采用双相区形变+IQ(双相区保温淬火)处理的组织中富Cu最高的区域面积为12.9%,比IQ工艺下富Cu区域提高108%;双相区形变+IQP工艺处理后实验钢的晶粒明显细化,且组织中块状残余奥氏体较多;与单一IQP工艺相比,双相区形变+IQP工艺处理的实验钢抗拉强度由1 253MPa提高到1 293MPa,伸长率由16.9%提高到18.3%,残余奥氏体体积分数由11.6%提高到13.8%,表明双相区30%的形变处理实现了促进Cu配分行为诱导残余奥氏体含量增加和细晶强化的双重效果。     

Quenching and Partitioning (Q&P) Processing of Martensitic Stainless Steels

Austenite was stabilized in the martensitic stainless steel grade AISI 420 by means of quenching and partitioning (Q&P) processing. The effects of quenching temperature on the microstructure and mechanical properties were investigated. The specimens processed at low quench temperatures (regime I) had a microstructure consisting of tempered martensite and retained austenite. At high quench temperatures (regime II), fresh martensite was present too. The highest austenite fraction of about 0.35 was obtained at the quench temperature delineating regimes I and II. The amount of carbon in retained austenite increased as the quench temperature decreased. The carbon level of austenite was, however, much lower than the carbon concentrations expected from full partitioning assumption. This was mainly due to the extensive cementite formation in the partitioning step. Stabilization of austenite by Q&P processing was found not to be purely chemical. Austenite stabilization was also assisted by locking, because of local carbon enrichment, of potential martensite nucleation sites in the austenite/martensite boundaries and in austenite defects. The importance of the latter stabilization mechanism increased at higher martensite fractions. According to the tensile test results, the Q&P processed specimen with the highest austenite fraction was not associated with the best combination of strength and ductility. The mechanical stability of austenite was found to increase with its carbon concentration being the highest at the lowest quench temperature. The thermal stability, on the other hand, was almost inversely proportional to the retained austenite fraction, being low at intermediate quench temperatures where the retained austenite fraction was high.     

Resistance Spot Welding of Quenching and Partitioning (Q&P) Third-Generation Advanced High-Strength Steel: Process–Microstructure–Performance

Metallurgical and Materials Transactions A - This paper investigates process–microstructure–performance relationships in Q&amp;P980 third-generation advanced high-strength steel...     

Microstructure and Wear Resistance in Medium and High C Steels Treated by Quenching and Partitioning

The quenching and partitioning (Q&P) steels have shown to be promising candidates to be applied in fields where wear resistance is required. In this study, a medium and a high C steel are heat treated by Q&P and the resulting microstructure, hardness, and wear resistance are characterized. The mechanical stability of the austenite phase under wear test conditions is investigated. It is found that the stability of austenite is very high in the high C steel and decreases in the medium C steel. Additionally, the hardness and wear behavior of the Q&P-treated steels are compared with the results obtained for quenching and tempering (Q&T) treated samples, showing that, although the hardness of Q&P steels is quite lower, the obtained wear rates are similar. It means that in the studied Q&P steels, although the austenite transformation into martensite does not occur considerably, the presence of austenite might play a key role in the wear resistance.     

Influence of Ni and Process Parameters in Medium Mn Steels Heat Treated by High Partitioning Temperature Q&P Cycles

In this work, two medium Mn steels (5.8 and 5.7 wt pct Mn) were subjected to a quenching and partitioning (Q&P) treatment employing a partitioning temperature which corresponded to the start of austenite reverse transformation (ART). The influence of a 1.6 wt pct Ni addition in one of the steels and cycle parameters on austenite stability and mechanical properties was also studied. High contents of retained austenite were obtained in the lower quenching temperature (QT) condition, which at the same time resulted in a finer microstructure. The addition of Ni was effective in stabilizing higher contents of austenite. The partitioning of Mn and Ni from martensite into austenite was observed by TEM–EDS. The partitioning behaviour of Mn depended on the QT condition. The lower QT condition facilitated Mn enrichment of austenite laths during partitioning and stabilization of a higher content of austenite. The medium Mn steel containing Ni showed outstanding values of the product of tensile strength (TS) and total elongation (TEL) in the lower QT condition and a higher mechanical stability of the austenite.