激光对碳纤维增强复合材料的热烧蚀数值模拟

高能激光对复合材料的辐照效应研究,可以拓展激光技术的应用范围。为了预测激光辐照下碳纤维增强复合材料的瞬态热响应,提出了一个简化计算模型。采用隐式有限体积方法求解控制方程,边界条件包括激光辐照加热、对流换热、辐射换热以及材料表面烧蚀。考虑了激光辐照过程中基体热分解、质量迁移、比热容变化情况。基于该烧蚀模型,预测了激光辐照下碳纤维增强复合材料的瞬态温度场和表面烧蚀速率,计算结果与文献试验数据一致。最后,通过修正烧蚀模型分析了高速气流剥蚀对激光辐照复合材料热效应的影响。     

切向气流对激光辐照树脂基复合材料的影响

 为了考察切向强迫气流对激光辐照下树脂基复合材料热响应的影响,基于边界层换热理论,研究了切向气流与靶面的对流换热系数和热分解气体对表面热交换的覆盖效应,并用有限差分法对激光辐照下树脂基复合材料的1维热响应模型进行数值求解。数值计算表明：高速切向气流的存在会加速靶材表面与外部环境的热交换,从而明显降低激光对靶材的加热效率;边界层换热理论给出的对流换热系数和覆盖因子是合理有效的,适用于数值模拟切向气流对激光辐照下树脂基复合材料热响应的影响;向靶材表面溢出的热分解气体对靶材表面与外部环境的热交换有一定的抑制作用,但影响较小,基本可以忽略不计。     

树脂基复合材料在连续激光作用下的损伤

 采用热压工艺制备了碳纤维布和高硅氧纤维布增强的环氧树脂和酚醛树脂基复合材料,研究了不同功率密度连续激光辐照下,复合材料的破坏形式及其组织结构与力学性能的变化。结果表明：当激光辐照功率密度大于0.1 kW/cm²后,树脂基体产生燃烧,碳纤维没有明显的损伤,而玻璃纤维布开始熔融,复合材料的拉伸性能降低30%~40%;当功率密度达到1 kW/cm²以后,除基体燃烧外,碳纤维复合材料产生明显的鼓泡分层,表层碳纤维有少量破断,而高硅氧纤维产生明显的熔融烧损,复合材料的拉伸性能降低80%以上。采用有限元计算方法,对碳纤维增强环氧树脂复合材料在连续激光辐照下的温度场进行了研究,计算结果与实验中复合材料的损伤行为相吻合。     

重频激光作用下碳纤维/环氧树脂复合材料热损伤规律

 运用热化学分析、扫描电子显微技术等手段,分析了碳纤维增强环氧树脂基复合材料在ms量级重频激光辐照下的损伤形式,研究了峰值功率密度、辐照时间、重复频率和脉冲宽度等对复合材料烧蚀规律的影响。研究结果表明：在激光辐照过程中,复合材料树脂基体在300 ℃开始裂解;由于裂解气体的保护作用,碳纤维不发生氧化,而是在汽化点（3 300 ℃）汽化烧蚀;复合材料热烧蚀率随峰值功率密度和重复频率提高而增大,随辐照时间增加而减小,最终均趋于定值;增加脉冲宽度可以提高辐照区峰值温度,降低碳纤维损伤的功率密度阈值。     

基于热释电探测器的重频脉冲激光诊断(英文)

以热释电探测器的工作原理为基础,研究了热释电探测器对重频脉冲激光的瞬态响应特性,建立了热释电探测器对单脉冲激光辐照响应的工作模型,分析了影响探测器频率特性的主要因素。根据材料和结构参数模拟计算了实际应用中的响应模型。设计了信号检测电路并对其进行计算仿真。完成了探测器的频率响应、脉宽响应等实验测量,验证了热释电探测器用于高重频、窄脉冲激光能量测量的可行性。     

光学窗口材料激光辐照热-力效应的解析计算研究

建立了高功率连续激光辐照透明光学材料的热力学模型,通过积分变换方法求解三维热传导方程,得出了激光辐照引起的瞬态温度场分布的精确解析解,并在此基础上进一步求得热应力场的瞬态分布。以1.315μm的高能氧碘激光辐照熔石英玻璃为例,计算了熔石英在激光辐照下的温度场与热应力场分布,分析了其激光损伤机理。研究结果表明由于熔石英具有优良的热稳定性,温度不均匀分布所产生的热应力相对较小,激光损伤主要是受辐照区域温度值超过材料熔点发生熔融破坏。理论分析结果与相关的实验结论一致,说明所建立激光辐照效应模型的合理性。     

纤维增强复合材料激光烧蚀效应的数值模拟

考虑材料的热解、氧化、相变及辐射和内外对流换热等物理过程,给出了激光烧蚀纤维增强复合材料的物理模型及数学模型。以碳纤维/环氧树脂复合材料为例,编程计算了材料的激光烧蚀过程,计算结果与实验结果符合得较好。计算结果表明：考虑复合材料的内对流时得到的结果更准确;较强功率密度激光辐照时,氧化对烧蚀的贡献可以忽略;功率密度一定时,烧蚀质量随时间近似为线性变化,功率密度越高,烧蚀效率越高。以辐照结束时背表面温度及烧蚀质量为目标物理量,对烧蚀过程做了参数敏感性分析,结果表明：热容及热导率对背表面温度的影响较大;树脂含量对烧蚀质量的影响较大,但其相对敏感度随激光功率密度增加而下降;激光功率密度超过1 kW/cm2时,辐射系数对烧蚀质量影响较大,但其相对敏感度随激光功率密度增加而下降。     

基于热释电探测器的重频脉冲激光诊断

摘以热释电探测器的工作原理为基础,研究了热释电探测器对重频脉冲激光的瞬态响应特性,建立了热释电探测器对单脉冲激光辐照响应的工作模型,分析了影响探测器频率特性的主要因素。根据材料和结构参数模拟计算了实际应用中的响应模型。设计了信号检测电路并对其进行计算仿事。完成了探测器的频率响应、脉宽响应等实验测量,验证了热释电探测器用于高重频、窄脉冲激光能量测量的可行性。     

激光辐照下PV型HgCdTe探测器反常响应机理

 利用PV型探测器开路电压的表达式,并考虑探测器的温度变化建立模型,对激光辐照下PV型HgCdTe探测器开路电压的变化进行了理论计算。当激光较弱时,计算结果与实验结果符合得很好。当激光较强时,对于辐照过程当中探测器输出变化的一般性趋势以及激光完全停照后的热弛豫过程,该模型也能给出较好的解释;但对于激光开始辐照时输出下跳和激光停止辐照时输出上跳的反常现象,该模型不能给出合理的解释。分析认为,该模型较好地描述了晶格温升对探测器输出的影响,但是它没有考虑热载流子效应;当激光较强时,热载流子效应不可忽略,特别是激光开始辐照和激光停止辐照时,载流子与晶格的温度差有比较明显的快速变化,从而导致了探测器的反常响应。     

激光辐照下复合材料树脂基热分解3维温度场模型

 采用控制体积法,从质量和能量守恒角度,推导了激光辐照下复合材料树脂基热分解时温度变化的基本方程。用多步模型描述树脂的热分解反应。提出了热分解气体的1维运动假设,这使得可以在3维情况下考虑热分解气体对流传输的影响,且在不引入力学量的前提下实现3维温度场模型的封闭。考虑到树脂基复合材料的各向异性,对部分分解材料的导热率计算公式进行了推导,并重新推导了部分分解材料对激光的吸收系数计算公式。在一定的简化下,推导的能量守恒方程与文献结果一致。     

Nonlinear optical properties of composites based on conductive metal-alkanoate liquid crystals

The dynamic holography in new composite materials based on a novel class of metal-alkanoate ionic liquid crystals (ILCs) is studied experimentally and theoretically. The composites are formed as a dielectric dye film covered by lyotropic metal-alkanoate ILC and ionic smectic glasses with doped dye molecules. The dynamic gratings are created by nanosecond pulses of double frequency Nd:YAP laser, the recording demonstrates fast erasure time of residual thermal gratings. The nonlinear optical properties are determined by the resonance nonlinearity in photosensitive centres of ILC. Note, that permanent relief gratings will be formed on a dielectric dye film only as well as in composite cells either with nematic LC or with polymers under action of pulsed laser radiation. Lyotropic ILC layer applied over the dye film provides the dynamic regime of grating recording in composite cells. We found a secondary thermal grating is much smaller, the conductive ILC matrix provides effective heat dissipation and erasure of this thermal grating. A theory of Raman-Nath self-diffraction holography on thin films followed from the wave equation and the nonlinear mechanism of absorption saturation is developed to explain experimental results.     

Thermal and electrical conductivity of poly(l-lactide)/multiwalled carbon nanotube nanocomposites

Multiwalled carbon nanotubes (MWCNTs) are considered to be the ideal reinforcing agent for high-strength polymer composites, because of their fantastic mechanical strength, high electrical and thermal conductivity and high aspect ratio. Polymer/MWCNTs composites are easily molded, and the resulting shaped plastic articles have a perfect surface appearance compared with polymer composites made using usual carbon or glass fibers. Good interfacial adhesion between the MWCNTs and the polymer matrix is essential for efficient load transfer in the composite. The ultrahigh strength polymer composites demand the uniform dispersion of the MWCNTs in the polymer matrix without their aggregation and the good miscibility between MWCNT and polymer matrix. This approach can also be applied to biodegradable synthetic aliphatic polyesters such as poly(l-lactide) (PLLA), which has received a great deal of attention due to environmental concerns. In this study, PLLA was melt-compounded with MWCNTs. A high degree of dispersion of the MWCNTs in the composites was obtained by grafting PLLA onto the MWCNTs (PLLA-g-MWCNTs). After oxidizing the MWCNTs by treating them with strong acids, they were reacted with l-lactide to produce the PLLA-g-MWCNTs. The mechanical properties of the PLLA/PLLA-g-MWCNT composite were higher than those of the PLLA/MWCNT composite. The electrical conductivity of the composites was determined by measuring the volume resistivity, which is a value of the resistance expressed in a unit volume by two-probe method. The thermal diffusivity and heat capacity of composites was measured by laser flash method, and the effects of modification of the MWCNT in PLLA matrix are discussed.     

玻璃纤维/环氧树脂复合材料热分解动力学参数的确定

采用热重分析仪对空气和氮气气氛中的玻璃纤维增强环氧树脂基复合材料进行热分析,得到该材料在空气气氛中的烧蚀热为3125～3440J/g,而在氮气气氛中并未出现明显的氧化放热峰。基于阿伦纽斯形式的多步分解模型和直接解法,计算了该材料在空气气氛中的热分解动力学参数。分析表明:阿伦纽斯形式的多步分解模型能够较好地描述该材料的热分解过程;直接解法适用于计算复合材料的热分解动力学参数;确立的热分解动力学参数是正确有效的。     

钨/石墨烯/钨面向等离子体复合材料力学与热学及耐辐照性能衰减的第一性原理计算

通过第一性原理计算研究了钨/石墨烯/钨复合材料相比于纯钨金属在力学与热学性质方面的变化,并用氦原子-空位缔合缺陷模拟核聚变辐照损伤评估等离子体辐照条件下的性能。计算结果表明：钨/石墨烯/钨复合材料的体积弹性模量、杨氏模量与剪切模量呈现一定程度的下降,但是提升了钨基材料的延展性;钨/石墨烯/钨复合材料的热膨胀系数有所增加,但是具有较高的最小热导率。本文阐述了石墨烯界面层可以对基体杂质与缺陷进行吸附的独特机制,通过这种机制,钨/石墨烯/钨复合材料在力学、热膨胀系数以及最小热导率有更低程度的衰减,这显示了钨/石墨烯/钨复合材料在抗辐照性能方面具有较大的应用潜力。     

Metal Matrix Composites for Thermal Management: A Review

The most challenging objective in the electronic industries is to develop materials that demonstrate a tunable thermal property with today's microelectronic devices. The development of composite material with balanced thermal properties is highly appreciated and currently competing the traditional monolithic conductive material. However, the tailored thermal properties of the composite are significantly influenced by the composites constituents and their fabrication routes. This article presents a review of thermal properties of particulate as well as fiber-reinforced composite proportional to matrix microstructure, reinforcement architecture. The processing techniques used to fabricate composites have been addressed with an objective to achieve suitable thermal properties. The developments in the analytical and numerical simulation approach to predict the thermal conductivity and CTE of the developed composites have been critically reviewed. Lastly, future work needs attention is summarized.     

激光诱导间质热疗中生物组织的温度场研究

激光诱导间质热疗疗效评估的前提是必须获得准确的激光在不同功率、不同照射时间的生物组织温度场分布.利用多物理场直接耦合分析软件COMSOL Multiphysics构建了在组织光学参量不变情况下的三维有限元传热模型.该模型基于Pennes生物传热方程和轴对称高斯形状的激光光束热源方程,参量针对离体猪肝组织,考虑到了生物组织热物性密度、比热和热导率随温度变化的情况.仿真获得激光功率为0.77 W、0.95 W、1.23 W,照射时间为10~90 s,径向距离0~2 mm范围和轴向距离0~4 mm范围的温度场数据集.利用拟合算法,获得了自变量为激光功率、照射时间、径向距离和轴向距离的生物组织温度场分布模型.将功率为0.88 W和1.05 W时的结果与Pennes方程结果相比较,两者误差在5%以内.     

Modelling of the transverse strength of fibre reinforced epoxy composite at low and high temperature

Process-induced thermal residual stresses and matrix failure of unidirectional carbon fibre reinforced composites (CFRP) have been investigated by finite element analysis (FEA). We used a partial discrete FEA model based on a unidirectional composite consisting of a microscopic area of fibres and matrix surrounded by a homogenised composite area. The FEA provided information about the stress state in the matrix and the fibre–matrix interface. The transverse strength of the composite was calculated regarding matrix failure and fibre matrix debonding. The influence of the temperature on the Young's modulus, the non-linear stress–strain behaviour and the strength of the matrix were investigated in detail. Following this approach it was possible to incorporate the resulting microresidual stresses on the transverse strength of the composite. Tensile tests of the neat resin and of the composite were performed in the temperature range of ?40°C to 60°C. The results of the FEA modelling are in good agreement with the experimental results of the transverse tests.     

混杂复合材料等效热传导性能预测的小波-机器学习混合方法

混杂复合材料是一种新型复合材料,其复杂的细观结构导致预测其等效热传导性能极富挑战性.本文结合渐近均匀化方法、小波变换方法和机器学习方法发展了一种新的可以有效预测混杂复合材料等效热传导性能的小波-机器学习混合方法.该方法主要包括离线多尺度建模和在线机器学习两部分.首先借助渐近均匀化方法通过离线多尺度建模建立了混杂复合材料的热传导性能材料数据库,然后利用小波变换方法对离线的材料数据库进行预处理,接下来分别运用人工神经网络和支持向量回归方法建立混杂复合材料等效热传导性能预测的在线机器学习模型.最后通过对周期和随机混杂复合材料进行数值实验,验证了小波-机器学习混合方法的有效性,数值实验结果表明小波-神经网络混合方法具有最优的预测效果和抗噪能力.此外,需要强调的是对于具有高维大规模数据特征的随机混杂复合材料,小波-机器学习混合方法不仅可以提取离线材料数据库的重要特征,还可以显著减少在线监督学习的输入数据规模并提高机器学习模型的训练效率及抗噪性能.本文建立的小波-机器学习混合方法不仅适用于混杂复合材料等效热传导性能的预测,还可进一步推广应用于复合材料等效物理、力学性能的预测.