The color properties of a reflective CMYK module using polymer‐dispersed liquid crystal (PDLC)

A reflective CMYK (cyan, magenta, yellow, and black) module using polymer‐dispersed liquid crystal (PDLC) is investigated for multi‐color reflective display. Combined with the electro‐optical properties and visible spectral reflectivity of PDLC films, the color properties of the reflective CMYK module were evaluated in terms of the Uniform Color Space‐CIE 1976 L*a*b*. It is found that the blue light reflectivity of the PDLC films is lower than green light and red light reflectivity. With the increase of the voltage applied on PDLC, the color lightness of the CMYK module generally decreases, while the color saturation increases. When the voltage changed from 0 to 70 V with a 5‐V change amplitude, modules C, M, Y, and K severally exhibit at least five, six, three, and seven colors.     

A full‐color eyewear display using planar waveguides with reflection volume holograms

Abstract— A full‐color eyewear display with over 85% see‐through transmittance with a 16° horizontal field of view was developed. Very low color crosstalk, less than 0.008 Δu′v′ uniformity, and 120% NTSC color gamut were achieved. Waveguides with two in‐ and out‐coupling reflection volume hologram elements enabled a simple configuration that has an optical engine beside the user's temples. The reflection volume hologram elements used on the waveguides realized a small thickness of 1.4 mm for each waveguide, and an out‐coupling reflection volume hologram used as an optical combiner contributed a high see‐through transmittance of 85% due to its wavelength selectivity. However, there are technical challenges in achieving a reasonable screen size and quality color images with optics that utilize holographic waveguides because holograms have large chromatic dispersions compared to conventional optical elements such as lenses and mirrors. Approaches to overcome these issues are described.     

Spatial optical modulator (SOM): Samsung's light modulator for next‐generation laser displays

Abstract— A new type of diffractive spatial optical modulators (SOMs) has been developed for projection‐display and other applications such as holographic data storage, programmable lithography, and optical communications. It exhibits the inherent advantages of fast response time and high‐performance light modulation, suitable for high‐quality and high‐resolution projection displays. The ±1st‐order efficiency and contrast ratio of 39% and 1000:1 was achieved for a prototype SOM. The response time can be as fast as 0.7μsec with a 400‐nm displacement, enough to make a full‐HD display, being driven by 10‐V. A laser display in full‐HD format (1920 × 1080) was successfully demonstrated by using prototype projection engines having SOM devices, signal‐processing circuits, and projection optics.     

Multi‐view 3‐D display employing a flat‐panel display with slanted pixel arrangement

Abstract— A flat‐panel display with a slanted subpixel arrangement has been developed for a multi‐view three‐dimensional (3‐D) display. A set of 3M × N subpixels (M × N subpixels for each R, G, and B color) corresponds to one of the cylindrical lenses, which constitutes a lenticular lens, to construct each 3‐D pixel of a multi‐view display that offers M × N views. Subpixels of the same color in each 3‐D pixel have different horizontal positions, and the R, G, and B subpixels are repeated in the horizontal direction. In addition, the ray‐emitting areas of the subpixels within a 3‐D pixel are continuous in the horizontal direction for each color. One of the vertical edges of each subpixel has the same horizontal position as the opposite vertical edge of another subpixel of the same color. Cross‐talk among viewing zones is theoretically zero. This structure is suitable for providing a large number of views. A liquid‐crystal panel having this slanted subpixel arrangement was fabricated to construct a mobile 3‐D display with 16 views and a 3‐D resolution of 256 × 192. A 3‐D pixel is comprised of 12 × 4 subpixels (M = 4 and N = 4). The screen size was 2.57 in.     

Chromatic characterization of novel multicolor reflective display with electrochemically size‐controlled silver nanoparticles

Multifunctional electrochromic materials that enable control of multiple colors, color density, and specular reflection are potential candidates for novel reflective display devices. In this research, we focus on Ag nanoparticles that exhibit various optical states based on their localized surface plasmon resonance (LSPR). Because the LSPR band depends on the size and shape of the nanoparticles, control of the morphology of Ag nanoparticles can lead to dramatic changes in color. In order to apply this color variation for display devices, we investigate here the electrochemical formation of size‐controlled Ag nanoparticles using a voltage‐step method that consists of an application of two successive different voltages (V₁ and V₂). The electrochemically deposited Ag nanoparticles appear red and blue depending on the time for V₂ voltage application. The color changes between the transparent and colored states are reversible. Then, we successfully demonstrate the first LSPR‐based multicolor electrochromic device in which reversible control of five optical states—transparent, silver mirror, red, blue, and black—is possible.     

Improvement of off‐axis color shift on hybrid viewing‐angle device using dual γ‐voltage method

We have mass production on one kind of liquid crystal display (LCD) device with hybrid viewing‐angle (HVA), which can be switched between the wide viewing‐angle (WVA) and narrow viewing‐angle (NVA) by one button. This device adopts the single cell design that with lower cost, and utilizes the optical properties of electrically tilted LC to achieve the function of NVA display. An issue has received less attention in the past and been indeed found in the production process. It is that the off‐axis color shift will appear in NVA mode. We put forward one method to improve this issue here, which is combined with the concepts of Gray Frame Insertion (GFI) and Impulse‐type driving. By switching the voltage between two different γ values, the color shift will be perfected on the produce.     

High performance color‐converted micro‐LED displays

A full‐color micro‐LED display can be achieved by red, green, and blue (RGB) chips or by a blue/ultraviolet (UV) micro‐LED array to pump downconverters. The latter helps relieve the burden of epitaxial growth of tri‐color micro‐LED chips. However, such a color‐converted micro‐LED system usually suffers from color crosstalk and low efficiency due to limited optical density of color converters. With funnel‐tube array and reflective coating on its inner surface, the crosstalk is eliminated, and the optical efficiency can be improved by more than two times. In addition, the ambient contrast ratio is also improved because of higher light intensity. The color gamut of this device is approximately 92% of DCI‐P3 standard.     

A method for selecting display primaries to match a target color gamut

Abstract— A method for selecting primaries of a wide‐gamut display is proposed, in which display color gamut is designed to match a target color gamut in CIELAB color space. A standard deviation of the relative maximum chroma of display and target color gamuts is defined. The selection method optimizes display primaries for the minimum standard deviation so that display and target color gamuts are similar in shape. It is shown that the color gamut of a laser display designed by this method is similar in shape to the theoretical maximum, or optimal, color gamut of objects. It is also shown that the color gamut of an LED display can be designed to include 99.7% of the gamut of Pointer's real‐world surface colors. LED primaries are selected to minimize the standard deviation of the relative maximum chroma of effective display color gamut and a target color gamut which is defined to include Pointer's real‐world surface colors. For both the laser and LED displays, it is necessary to constrain the red‐primary wavelength to avoid excessive optical power for the red primary.     

Active matrix field sequential color electrically suppressed helix ferroelectric liquid crystal for high resolution displays

In this article, we disclose a 3‐inch 250ppi active matrix field sequential color (FSC) display based on electrically suppressed ferroelectric liquid crystal (ESHFLC). ESHFLC's ultra‐fast response time (~10 μs at 6.67 V/μm) enables the display resolution to be tripled via FSC technique. The photo‐alignment technology provides ESHFLC with optimal anchoring energy that contributes to a high contrast ratio over 10 K:1 on single pixel level measurement. A specific 3T1C pixel circuit is designed to generate continuous gray scale from FLC binary switching by utilizing the pulse width modulation concept. The low temperature poly silicon thin‐film transistor array has been used to fabricate the FSC ESHFLC display panel. We achieved an 8‐bit gray level for each color subframe, that is, R, G, and B colors that results in 24‐bit color images. We believe, because of the good optical quality and cost‐effective fabrication, this display may replace in‐plane switching or fringe‐field switching in the near future for the portable device market. Moreover, high resolution FSC ESHFLCs can find applications in the emerging virtual reality displays.     

Multi‐primary‐color LCD: Its characteristics and extended applications

Abstract— The development of multi‐primary‐color (MPC) display systems is one of the big paradigm shifts in recent display technologies and induces new potentials of display devices. The development of MPC display systems for different goals is briefly reviewed. Especially, by employing MPC systems, it is possible to reproduce the real material colors faithfully and efficiently. For signal processing, MPC systems have a big advantage in the so‐called color‐reproduction redundancy. A number of applications can be derived from this characteristic, such as improving the viewing‐angle dependency issue and power savings. On the other hand, MPC systems have a typical trade‐off versus RGB‐standardized input signals, especially for reproducing bright green. New algorithms to moderate this trade‐off on MPC systems by employing color‐reproduction redundancy are proposed. The goal of our algorithms is to maintain the compatibility with RGB‐based input signals though the initial display design so that the characteristics of MPC systems are not changed or lost. These algorithms indicate that MPC display systems are applicable not only for a specifically limited objective but also for other applications, e.g., TV broadcasting.     

Flexible AMOLED displays on stainless‐steel foil

Abstract— The world's thinnest flexible full‐color 5.6‐in. active‐matrix organic‐light‐emitting‐diode (AMOLED) display with a top‐emission mode on stainless‐steel foil was demonstrated. The stress in the stainless‐steel foil during the thermal process was investigated to minimize substrate bending. The p‐channel poly‐Si TFTs on stainless‐steel foil exhibited a field‐effectmobility of 71.2 cm²/N‐sec, threshold voltage of ?2.7 V, off current of 6.7 × 10¹³ A/μm, and a subthreshold slope of 0.63 V/dec. These TFT performances made it possible to integrate a scan driver circuit on the panel. A top‐emission EL structure was used as the display element, and thin‐film encapsulation was performed to realize a thin and flexible display. The full‐color flexible AMOLED display on stainless‐steel foil is promising for mobile applications because of its thin, light, rugged, and flexible properties.     

A video‐speed reflective display based on electrowetting: principle and properties

Abstract— Electrowetting is presented as a novel principle for a reflective display. By contracting a colored oil film electrically, an optical switch is obtained with many attractive properties that make it very suitable for use as a reflective display, for instance, as electronic paper. Firstly, it has the high reflectivity (>40%) and contrast ratio (15) required for a paper‐like optical appearance. In addition, the principle shows a video‐rate response time (<10 msec) and has a clear route toward a high‐brightness color display. Finally, the electro‐optical response is independent of cell‐gap thickness, which will be very beneficial when moving toward a flexible display.     

Hybrid MEMS optical scanner for volumetric 3‐D displays

Abstract— A fabrication technique and characteristics of high‐power‐handling microelectromechanical systems (MEMS) optical scanners for laser 3‐D volumetric‐image display application is reported. The MEMS scanner is designed to control the reflection of high‐power YAG‐laser beam by using the optomechanical combination of a dielectric‐film‐coated mirror cube and an electrostatic‐MEMS‐scanner platform. These hybrid‐type MEMS optical scanners have a stroke of about 20° at resonant frequencies of 600 Hz when a 45‐V pulse voltage is applied.     

A 3.0‐in. 308‐ppi WVGA AMOLED with a top‐emission white OLED and color filter

Abstract— A 3.0‐in. 308‐ppi WVGA top‐emission AMOLED display with a white OLED and color filters, driven by LTPS TFTs demonstrating a color gamut of >90% and a Δ(u′,v′) of <0.02 is reported. A white‐emission source with a unique device structure was developed using all fluorescent materials and yielded efficiencies of 8.45% and 16 cd/A at 4000 nits with CIE color coordinates of (0.30, 0.32).     

The luminance resolution characteristics of multi‐primary‐color display

Abstract— In this paper, the resolution characteristics of multi‐primary‐color (MPC) display systems are analyzed. That four‐primary‐color (4PC) displays can increase the effective resolution for achromatic images in the luminance domain by a factor of two as compared to conventional RGB‐based displays with MPC‐specialized subpixel rendering, which is proposed in this paper, is demonstrated. Five‐ and six‐primary‐color (5PC and 6PC) display systems can reproduce denser luminance data than conventional RGB‐based display systems and solve a problem of MPC displays, viz. an increase of production costs and a decrease in the aperture ratio caused by increasing the number of subpixels in one pixel. This is an essential advantage of MPC display systems, which is related to the combination of the proposed color‐filter architecture and image processing. Thus, a completely new advantage of MPC display systems, in addition to their well‐known capabilities of color reproduction and power saving, is proposed.     

Power‐saving primary design for displays enclosing a target color gamut

Abstract— Display primaries are optimized for the trade‐off between the total primary power and color gamut under the requirement that a target color gamut is enclosed by the color gamut of the display. LED displays and HDTV color gamut are taken as examples. Compared to the display using a set of typical commercial RGB LEDs, it was found that a total optical (electrical) power of 23.6% (15.6%) can be saved for the display using optimal RGB LEDs. Although the size of the display color gamut is sacrificed, the color gamut of the display using optimal RGB LEDs still encloses the HDTV color gamut. The combined effect of the LED luminous efficiency and white‐point condition on the determination of the optimal LED wavelengths and bandwidths is also studied.     

OLED‐based pico‐projection system

Abstract— Two pico‐projection systems, a monochrome green and a full‐color system, based on high‐efficiency OLED microdisplays (VGA; pixel size, 12 μm) are presented. Both optical systems are described by a numerical aperture of about 0.3, a magnification of 15x, and a working distance of 300–360 mm. The frequency limit of both systems is 42 cycles/mm at an image contrast of about 60%. The monochrome projection system with a volume smaller than 10 cm³ consists of one green OLED and a projection lens with five elements. The measured luminance in the image plane is about 0.061 lm. The image has a diagonal of 150 mm with a working distance of about 300 mm and has a considerable image contrast of 396:1. The second system combines three high‐brightness OLEDs, red, green, and blue colored, together with a projection lens and an image‐combining element, and an X‐Cube to achieve full‐color projection. The estimated luminance value for the three‐panel projection unit with an OLED luminance of 10,000 cd/m² for each display will be about Φcalculated = 0.147 lm. In this paper, the system concepts, the optical designs, and the realized prototypes of the monochrome and full‐color projection system are presented.     

Masking model for accurate colorimetric characterization of LCD

Abstract— A color management system (CMS) such as ICC profile or sRGB space have been proposed for color transformation and reproduction of cross media. In such a CMS, accurate colorimetric characterization of a display device plays a critical role in achieving device‐independent color reproduction. In the case of a CRT, colorimetric characterization based on a GOG model is accurate enough for this purpose. However, there is no effective counterpart in liquid‐crystal displays (LCDs) since the characterization of an LCD has many difficulties, such as channel interaction and non‐constancy of channel chromaticity. In this paper, a new method of display characterization is proposed which is applicable to the assessment of color reproduction of LCDs. The proposed method characterizes an electro‐optical transfer function considering both channel interaction and non‐constancy of channel chromaticity. Experimental results show that the proposed method is very effective in the colorimetry of LCDs.     

Spatially uniform colors for projectors and tiled displays

Abstract— A major issue when setting up multi‐projector tiled displays is the spatial non‐uniformity of the color throughout the display's area. Indeed, the chromatic properties do not only vary between two different projectors, but also between different spatial locations inside the displaying area of one single projector. A new method for calibrating the colors of a tiled display is presented. An iterative algorithm to construct a correction table which makes the luminance uniform over the projected area of one single projector is presented first. This so‐called intra‐projector calibration uses a standard camera as a luminance measuring device and can be processed in parallel for all projectors. Once the color inside each projector is spatially uniform, the set of displayable colors — the color gamut — of each projector is measured. On the basis of these measurements, the goal of the inter‐projector calibration is to find an optimal gamut shared by all the projectors. Finding the optimal color gamut displayable by n projectors in time O(n) is shown, and the color conversion from one specific color gamut to the common global gamut is derived. The method of testing it on a tiled display consisting of 48 projectors with large chrominance shifts was experimentally validated.     

Achieving a foldable and durable OLED display with BT.2020 color space using innovative color filter structure

A foldable active‐matrix organic light‐emitting diode display capable of enduring very severe folding and environmental impact was obtained using symmetric panel stacking with an innovative design of color filter structure. The display was subjected to in situ folding cycle under an ambient test condition of 60°C/90% relative humidity, and no performance degradation was found for the display and the touch function during and after the test. In addition, 95% coverage of BT.2020 color space was obtained without additional power consumption compared with that of the panel with National Television System Committee (NTSC) color space.