热处理对 Ba0.6Sr0.4TiO3 厚膜介电性能的影响

采用柠檬酸盐法制备了Ba_(0.6)Sr_(0.4)TiO_3粉体,通过丝网印刷法制备了Ba_(0.6)Sr_(0.4)TiO_3厚膜,研究了在空气气氛中进行热处理前后厚膜样品的介电性能。研究结果表明,在空气气氛中进行热处理可以有效地提高厚膜样品的介电性能。经过1000°C热处理,厚膜样品在10 kH z下的介电损耗由1.7%降为1.1%,其优质系数由33提高到55。     

Effect of HfO2 content on the microstructure and piezoelectric properties of (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃–xHfO₂ [BNBT–xHfO₂] lead-free ceramics were prepared using the conventional solid-state reaction method. Effects of HfO₂ content on their microstructures and electrical properties were systematically studied. A pure perovskite phase was observed in all the ceramics with x=0–0.07 wt%. Adding optimum HfO₂ content can induce dense microstructures and improve their piezoelectric properties, and a high depolarization temperature was also obtained. The ceramics with x=0.03 wt% possess optimum electrical properties (i.e., d₃₃~168 pC/N, k_p~32.1%, Q_m~130, ε_r~715, tan δ~0.026, and T_d~106 °C, showing that HfO₂-modified BNBT ceramics are promising materials for piezoelectric applications.     

Dielectric and ferroelectric properties of Ba0.8Sr0.2Ti1−5x/4NbxO3 ceramics

Ba_0.8Sr_0.2Ti_1−5x/4Nb_xO₃ ceramics, x = 0, 0.01, 0.05, 0.10, were fabricated by conventional solid-state reaction. With increasing niobium content the ferroelectric phase transition temperature decreases linearly, and the dispersivity of the transition increases. Niobium B-site decreases transition temperature more pronounced than Sr²⁺ at A-site. The heterovalent substitution of Nb⁵⁺ in low content causes local defect dipole, while more substitutions introduce disorder to disturb the long-range dipole correlation. Ba_0.8Sr_0.2Ti_1−0.5/4Nb_0.1O₃ ceramic shows weak ferroelectric loop at room temperature far from its transition temperature, 153 K.     

Synthesis of Bi0.5(Na0.7K0.2Li0.1)0.5TiO3 powders through the molten salt method

The Bi_0.5(Na_0.7K_0.2Li_0.1)_0.5TiO₃ powder synthesis through molten salt method was investigated in the temperature range of 650–700 °C for 2–4 h. The XRD results indicated that the optimal synthesizing temperature for molten salt method was 700 °C, significantly lower than that for conventional processing route of solid state reaction method, where a calcining temperature of 850 °C was needed. The SEM results revealed better crystallization of the powders obtained through molten salt method, compared with those through the conventional processing route of solid state reaction method.     

Effect of TiO2 doped Ni electrodes on the dielectric properties and microstructures of (Ba0.96Ca0.04)(Ti0.85Zr0.15)O3 multilayer ceramic capacitors

The effects of TiO₂-doped Ni electrodes on the microstructures and dielectric properties of (Ba_0.96Ca_0.04)(Ti_0.85Zr_0.15)O₃ multilayer ceramic capacitors (MLCCs) have been investigated. Nickel paste with a TiO₂ dopant was used as internal electrodes in MLCCs based on (Ba_0.96Ca_0.04)(Ti_0.85Zr_0.15)O₃ (BCTZ) ceramic with copper end-termination. The microstructures and defects were analysed by microstructural techniques (SEM/HRTEM) and energy-dispersive spectroscopy (EDS). The continuity of the electrode of the MLCC was measured using a scanning electron microscope, which showed that the continuity of the electrode for the MLCC with a TiO₂-doped Ni electrode was approximately 90%. However, continuity of the electrode for a conventional MLCC was below 80%. The continuity of the TiO₂-doped Ni electrode showed significant improvement in the MLCC, which was due to no reaction between Ni and BCTZ.     

Hydrothermal synthesis and characterization of Na0.5Bi0.5TiO3 microcubes

Na_0.5Bi_0.5TiO₃ microcubes with smooth faces and clear, well-defined edges have been successfully prepared for the first time by a simple hydrothermal method without any surfactants. The as-prepared Na_0.5Bi_0.5TiO₃ microcubes showed an obvious emission band compared with nanoparticles, which is attributed to the different NBT morphology and size.     

基于WO3-MoO3和TiO2/CdS复合电极的光电致变色器件

电致变色广泛应用于智能窗领域,但电致变色材料仍需外部电源驱动,将太阳能电池与电致变色材料结合起来的光电致变色器件可实现无需外部供电的智能变色调控。性能优异的变色阴极和光阳极是当下光电致变色器件的研究热点。通过水热法制备WO₃-MoO₃薄膜,研究其电致变色性能;通过水热法结合连续离子层沉积法制备TiO₂/CdS复合薄膜,研究其光电转换性能。最后将WO₃-MoO₃薄膜和TiO₂/CdS复合薄膜分别作为光电致变色器件的变色阴极、光阳极构建WO₃/MoO₃-TiO₂/CdS光电致变色器件。WO₃/MoO₃-TiO₂/CdS光电致变色器件具有较大的光学调制范围(630nm处为41.99%)、更高的着色效率(35.787%),将其作为智能窗应用在现代建筑、通行工具等领域具有重要应用价值。     

The optimum conditions for preparing the lead-free piezoelectric ceramic of Bi0.5Na0.5TiO3 using the Taguchi method

Using the Taguchi method, this study analyzes the optimum conditions for preparing the disk of bismuth sodium titanate (Bi_0.5Na_0.5TiO₃), BNT, which is prepared using the mixed oxide method. The controllable factors used in this study consisted of the following: (1) the duration of milling; (2) the temperature of calcining; (3) the rotation speed of mill; and (4) the temperature of sintering. According to the optimum conditions, the confirmation experiment was carried out, and the relative density of the BNT disk, which was prepared without adding the additive, was up to 89.05%. The percentage contribution of each controllable factor was also determined. Most interestingly, the temperature of sintering is the most influential factor to press the BNT powder together tightly, and its value of percentage contribution is up to 94.94%.     

Electrical energy density and dielectric properties of poly(vinylidene fluoride-chlorotrifluoroethylene)/BaSrTiO3 nanocomposites

A series of poly(vinylidene fluoride-chlorotrifluoroethylene) (P(VDF-CTFE))/barium strontium titanate (BST) nanocomposites were fabricated by solution casting method. The addition of BST nanoparticles could enhance both the dielectric constant and the displacement of the resultant composite significantly. The surface activation of BST nonaparticles with KH550 was confirmed as an effective way to improve the breakdown strength of the composite. The high electric displacement (D > 15 μC/cm²), breakdown field (>200 MV/m) and low dielectric loss in P(VDF-CTFE)/BST nanocomposites suggest that the high electrical energy density may be desirable. That indicates the potential application of this class of copolymer/ceramics nanocomposites for high energy storage components.     

An efficient approach for direct synthesis of K0.5Na0.5NbO3 powders

Pure K_0.5Na_0.5NbO₃ powders were prepared at low temperatures by an efficient method using Na₂CO₃, K₂CO₃ and Nb₂O₅ as raw materials and urea as fuel. The phase evolution of the powders was investigated by X-ray diffractometer (XRD) and thermo gravimetric analysis-differential scanning calorimeter (TG-DSC). The phase composition and morphology of the powders were characterized by electron probe microanalysis (EPMA) and scanning electron microscope (SEM), respectively. The results reveal that single-phase K_0.5Na_0.5NbO₃ powder can be obtained at 550 °C by the method. The as-prepared powder is stoichimetric, fine and well-developed.     

Effects of sintering temperature and poling conditions on the electrical properties of Ba0.70Ca0.30TiO3 diphasic piezoelectric ceramics

The effects of sintering temperature and poling conditions on the electrical properties of tetragonal and orthorhombic diphasic Ba_0.70Ca_0.30TiO₃ (BCT) lead-free ceramics have been systematically investigated. On the one hand, with increasing sintering temperature from 1270 °C to 1400 °C, the bulk density increases monotonically and the Curie temperature keeps almost constant with the value of ∼120 °C, whereas the grain size, the maximum relative dielectric constant, room temperature polarization reach the maximum values for samples sintered at 1340 °C. On the other hand, it is found that the piezoelectric property depends on poling electric field and poling temperature significantly. An enhanced piezoelectric behavior of d₃₃=126 pC/N, k_p=0.29, and Q_m=588 is obtained for the BCT ceramics poled at 100 °C with 30 kV/cm field for 20 min. The aging behavior of the piezoelectric property is also investigated.     

All-solid-state lithium battery with a three-dimensionally ordered Li1.5Al0.5Ti1.5(PO4)3 electrode

To fabricate all-solid-state Li batteries using three-dimensionally ordered macroporous Li_1.5Al_0.5Ti_1.5(PO₄)₃ (3DOM LATP) electrodes, the compatibilities of two anode materials (Li₄Mn₅O₁₂ and Li₄Ti₅O₁₂) with a LATP solid electrolyte were tested. Pure Li₄Ti₅O₁₂ with high crystallinity was not obtained because of the formation of a TiO₂ impurity phase. Li₄Mn₅O₁₂ with high crystallinity was produced without an impurity phase, suggesting that Li₄Mn₅O₁₂ is a better anode material for the LATP system. A Li₄Mn₅O₁₂/3DOM LATP composite anode was fabricated by the colloidal crystal templating method and a sol-gel process. Reversible Li insertion into the fabricated Li₄Mn₅O₁₂/3DOM LATP anode was observed, and its discharge capacity was measured to be 27 mA h g⁻¹. An all-solid-state battery composed of LiMn₂O₄/3DOM LATP cathode, Li₄Mn₅O₁₂/3DOM LATP anode, and a polymer electrolyte was fabricated and shown to operate successfully. It had a potential plateau that corresponds to the potential difference expected from the intrinsic redox potentials of LiMn₂O₄ and Li₄Mn₅O₁₂. The discharge capacity of the all-solid-state battery was 480 μA h cm⁻².     

TiO2 as a sintering additive for KNbO3 ceramics

Improved densification during the conventional sintering of KNbO₃ ceramics was achieved by using small additions of TiO₂. This improved densification can be explained on the basis of high-temperature chemical reactions in the system. X-ray diffractometry and electron microscopy were used in combination with diffusion-couple experiments in order to elucidate the chemical reactions between KNbO₃ and TiO₂. TiO₂ reacts with KNbO₃ forming KNbTiO₅, and a low concentration of Ti incorporates in the KNbO₃ structure resulting in the formation of oxygen vacancies and, consequently, in an improvement in the densification. At ∼1037 °C eutectic melting between the KNbO₃ and the KNbTiO₅ further improves the densification of the KNbO₃ ceramics.     

Raman and dielectric investigation of (Ba0.9−xSrxCa0.1)(Ti0.8Zr0.2)O3 ferroelectric ceramics

Solid solutions of (Ba_0.9−xSr_xCa_0.1)(Ti_0.8Zr_0.2)O₃ (BSCTZ) (0.1≤x≤0.4) were prepared using the conventional solid state reaction method. The effects of the substitution content on the crystallographic structure, phase transition and dielectric properties of the samples were investigated by dielectric and Raman spectroscopy over a wide temperature range from 100 to 500 K. All the samples were noted to undergo a diffuse phase transition from the tetragonal to the cubic phase and to exhibit a relaxor ferroelectric behavior.     

Effect of TiO2 supporting layer on Fe2O3 photoanode for efficient water splitting

For an electrochemical water splitting system, titanate nanotubular particles with a thickness of ∼700 nm produced by a hydrothermal process were repetitively coated on fluorine-doped tin oxide (FTO) glass via layer-by-layer self-assembly method. The obtained titanate/FTO films were dipped in aqueous Fe solution, followed by heat treatment for crystallization at 500 °C for 10 min in air. The UV–vis absorbance of the Fe-oxide/titanate/FTO film showed a red-shifted spectrum compared with the TiO₂/FTO coated film; this red shift was achieved by the formation of thin hematite-Fe₂O₃ and anatase-TiO₂ phases verified using X-ray diffraction and Raman results. The cyclic voltammetry results of the Fe₂O₃/TiO₂/FTO films showed distinct reversible cycle characteristics with large oxidation–reduction peaks with low onset voltage of I–V characteristics under UV–vis light illumination. The prepared Fe₂O₃/TiO₂/FTO film showed much higher photocurrent densities for more efficient water splitting under UV–vis light illumination than did the Fe₂O₃/FTO film. Its maximum photocurrent was almost 3.5 times higher than that obtained with Fe₂O₃/FTO film because of the easy electron collection in the current collector. The large current collection was due to the existence of a TiO₂ base layer beneath the Fe₂O₃ layer.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

Efficient decomposition of organic compounds with FeTiO3/TiO2 heterojunction under visible light irradiation

FeTiO₃/TiO₂, a new heterojunction-type photocatalyst working at visible light, was prepared by a simple sol–gel method. Not only did FeTiO₃/TiO₂ exhibit greatly enhanced photocatalytic activity in decomposing 2-propanol in gas phase and 4-chlorophenol in aqueous solution, but also it induced efficient mineralization of 2-propanol under visible light irradiation (λ ≥ 420 nm). Furthermore, it showed a good photochemical stability in repeated photocatalytic applications. FeTiO₃ showed a profound absorption over the entire visible range, and its valence band (VB) position is close to that of TiO₂. The unusually high photocatalytic efficiency of the FeTiO₃/TiO₂ composite was therefore deduced to be caused by hole transfer between the VB of FeTiO₃ and TiO₂.     

Synthesis and microstructure of (LaSr)MnO3 and (LaSr)FeO3 ceramics by a reaction-sintering process

(La_xSr_1−x)MnO₃ (LSMO) and (La_xSr_1−x)FeO₃ (LSFO) (x = 0.2–0.4) ceramics prepared by a simple and effective reaction-sintering process were investigated. Without any calcination involved, La₂O₃ and SrCO₃ were mixed with MnO₂ (LSMO) or Fe₂O₃ (LSFO) then pressed and sintered directly. LSMO and LSFO ceramics were obtained after 2 and 4 h sintering at 1350–1400 and 1200–1280 °C, respectively. Grain size decreased as La content increased in LSMO and LSFO ceramics.     

TiO2 photocatalyst loaded on hydrophobic Si3N4 support for efficient degradation of organics diluted in water

TiO₂ photocatalyst loaded on Si₃N₄ (TiO₂/Si₃N₄) was prepared by a conventional impregnation method and its photocatalytic performance for the degradation of organics (2-propanol) diluted in water was compared with that of TiO₂ photocatalysts (TiO₂/SiO₂, TiO₂/Al₂O₃, and TiO₂/SiC) loaded on various types of supports (SiO₂, Al₂O₃, and SiC). The formation of the well-crystallized anatase phase of TiO₂ was observed on the calcined TiO₂/Si₃N₄ photocatalyst, while a small anatase phase of TiO₂ was observed on the TiO₂/SiC photocatalyst and amorphous TiO₂ species was the main component on the TiO₂/SiO₂ and TiO₂/Al₂O₃ photocatalysts. The measurements of the water adsorption ability of photocatalysts indicated that the TiO₂/Si₃N₄ photocatalyst exhibited more hydrophobic surface properties in comparison to other support photocatalysts. Under UV-light irradiation, the TiO₂/Si₃N₄ photocatalyst decomposed 2-propanol diluted in water into acetone, CO₂, and H₂O, and finally, acetone was also decomposed into CO₂ and H₂O. The TiO₂/Si₃N₄ photocatalyst showed higher photocatalytic activity than TiO₂ photocatalyst loaded on other supports. The well-crystallized TiO₂ phase deposited on Si₃N₄ and the hydrophobic surface of Si₃N₄ support are important factors for the enhancement of photocatalytic activity for the degradation of organic compounds in liquid-phase reactions.     

Formation of LiNi0.5Co0.5VO4 nano-crystals by solvothermal reaction

LiNi_0.5Co_0.5VO₄ nano-crystals were solvothermally prepared using a mixture of LiOH·H₂O, Ni(NO₃)₂·6H₂O, Co(NO₃)₂·6H₂O and NH₄VO₃ in isopropanol at 150–200 °C followed by 300–600 °C calcination to form powders. TGA curves of the solvothermal products show weight losses due to evaporation and decomposition processes. The purified products seem to form at 500 °C and above. The products analyzed by XRD, selected area electron diffraction (SAED), energy dispersive X-ray (EDX) and atomic absorption spectrophotometer (AAS) correspond to LiNi_0.5Co_0.5VO₄. V–O stretching vibrations of VO₄ tetrahedrons analyzed using FTIR and Raman spectrometer are in the range of 620–900 cm⁻¹. A solvothermal reaction at 150 °C for 10 h followed by calcination at 600 °C for 6 h yields crystals with lattice parameter of 0.8252 ± 0.0008 nm. Transmission electron microscope (TEM) images clearly show that the solvothermal temperatures play a more important role in the size formation than the reaction times.