Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000     

Novel amorphous perfluorocopolymeric system: Copolymers of perfluoro‐2‐methylene‐1,3‐dioxolane derivatives

Perfluorotetrahydro‐2‐methylene‐furo[3,4‐d][1,3]dioxole (monomer I ) and perfluoro‐2‐methylene‐4‐methoxymethyl‐1,3‐dioxolane (monomer II ) are soluble in perfluorinated or partially fluorinated solvents and readily polymerize in solution or in bulk when initiated by a free‐radical initiator, perfluorodibenzoyl peroxide. The copolymerization parameters have been determined with in situ ¹⁹F NMR measurements. The copolymerization reactivity ratios are r _I = 1.80 and r _II = 0.80 in 1,1,2‐trichlorotrifluoroethane at 41 °C and r _I = 0.97 and r _II = 0.85 for the bulk polymerization. These data show that this copolymerization pair has a good copolymerization tendency and yields nearly ideal random copolymers. The copolymers have only one glass‐transition temperature from 101 to 168 °C, depending on the copolymer compositions. Melting endotherms have not been observed in their differential scanning calorimetry traces, and this indicates that all the copolymers with different compositions are completely amorphous. These copolymers are thermally stable (the initial decomposition temperatures are higher than 350 °C under an N₂ atmosphere) and have low refractive indices and high optical transparency from UV to near‐infrared. Copolymer films prepared by casting were flexible and tough. These properties make the copolymers ideal candidates as optical and electrical materials. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1613–1618, 2006     

Synthesis and characterization of polyimides from bis(3‐aminophenyl)‐4‐(1‐adamantyl)phenoxyphenyl phosphine oxide

A novel diamine, bis(3‐aminophenyl)‐4‐(1‐adamantyl)phenoxyphenyl phosphine oxide (mDAATPPO), was synthesized via the Williamson ether reaction of 4‐(1‐adamantyl)phenol and bis(3‐nitrophenyl)‐4‐fluorophenyl phosphine oxide, followed by reduction. The phenol group was prepared by the Friedel–Crafts reaction of 1‐bromoadamantane and phenol, whereas the phosphine oxide group was synthesized by the Grignard reaction of 1‐bromo‐4‐fluorobezene and diphenyl phosphinic chloride, followed by nitration. The monomer and its intermediate compounds were characterized with Fourier transform infrared, NMR, and melting‐point apparatus. The monomer was then used to prepare polyimides with 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride, 4,4′‐oxydiphthalic dianhydride, and pyromellitic dianhydride by the conventional two‐step synthesis: the preparation of poly(amic acid) followed by solution imidization. The molecular weights of the polyimides were controlled to 20,000 g/mol by off‐stoichiometry, and the synthesized polyimides were characterized with Fourier transform infrared, NMR, gel permeation chromatography, thermogravimetric analysis, and differential scanning calorimetry. In addition, the solubility, intrinsic viscosity, dielectric constant, and birefringence of the polyimides were evaluated. Novel polyimides with mDAATPPO exhibited good solubility, high glass‐transition temperatures (290–330 °C), excellent thermal stability (>500 °C), low dielectric constants (2.77–3.01), low refractive indices, and low birefringence values (0.0019–0.0030). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2567–2578, 2006     

Fluorene‐rich high performance polyesters: Synthesis and characterization of 9,9‐fluorenylidene and 2,7‐fluorenylene‐based polyesters with excellent optical property

Polyesters PEs containing high content of fluorene units in their backbones were synthesized from 9,9‐diarene‐substituted fluorene diols ( 1 ) and fluorene‐based diacid chlorides ( 2 ) by high temperature polycondensation at 185 °C in diphenyl ether. The molecular weights of the polyesters PE1‐PE5 were in a range of M_w 25,000–165,000. The polyesters displayed their high thermostability: the glass transition temperatures (T_g) by differential scanning calorimetry analysis ranged from 109 to 217 °C, while the 10% weight loss temperatures (T_d10) measured by thermogravimetric analysis were over 400 °C in nitrogen and 395 °C in air. The polyesters had good solubility in most common organic solvents such as chloroform and toluene and gave tough, transparent and flexible cast films. The transmittance of the films was over 80% in the wavelength range from 450 to 700 nm in any PEs . The PEs exhibited high refractive index values around 1.65, while they had very low degree of birefringence. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2549–2556, 2008     

Novel heterocyclic poly(arylene ether ketone)s: Synthesis and polymerization of 4‐(4′‐hydroxyaryl)(2H)phthalazin‐1‐ones with methyl groups

Based on green chemistry, a simple and efficient direct synthesis of 4‐(4′‐hydroxyaryl)(2H)phthalazin‐1‐ones ( 2a–2f ) was developed in a two‐step reaction, in which the Friedel–Crafts acylation reaction of six phenols with phthalic anhydride was initially carried out and then followed by cyclization with hydrazine hydrate in good to excellent yields with high regioselectivity. A number of novel heterocyclic poly(arylene ether ketone)s were prepared conveniently from several unsymmetrical, twist, and noncoplanar phthalazinone‐containing monomers ( 2a–2f ) and an activated difluoro monomer via a N? C coupling reaction. It was very interesting that the obtained monomers and polymers exhibited diverse properties with the variation of the number and location of the substituted methyl groups. All these polymers had a high molecular weight with M_n and η_inh in the range of 44,960–169,000 Da and 0.38–0.79 dL/g, respectively. Actually, the obtained polymers displayed excellent thermal properties with T_g's ranging from 222 to 248 °C and 5% weight loss temperatures in nitrogen higher than 430 °C. Moreover, these polymers were readily soluble in common organic solvents, such as N‐methyl‐2‐pyrrolidone, chloroform, pyridine, and m‐cresol, and could be cast into flexible and colorless or nearly colorless films by spin‐coating or casting processes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1525–1535, 2007     

Synthesis of Early‐Transition‐Metal Carbide and Nitride Nanoparticles through the Urea Route and Their Use as Alkylation Catalysts

The use of urea as either a carbon or a nitrogen source enabled the synthesis of various early‐transition‐metal nitride and carbide nanoparticles (TiN, NbN, Mo₂N, W₂N, NbC_xN_1?x, Mo₂C and WC). The ability of these particles to promote alkylation reactions with alcohols was tested on benzyl alcohol and acetophenone at 150 °C for 20 h in xylene. Group IV and V ceramics proved to be able to catalyse the formation of 1,3‐diphenyl propenone, whereas group VI ceramics showed a tendency to promote the Friedel–Crafts‐type reaction of benzyl alcohol on xylene (the solvent). TiN featured the highest activity for the alkylation of ketones and was further tested for more difficult alkylations. Group VI ceramics were further investigated as catalysts for the Friedel–Crafts‐type alkylation of aromatics with activated alcohols. Interestingly, even hexanol could be effectively used for these reactions.     

Synthesis and characterization of polyaryleneetherketone triphenylphosphine oxides incorporating cycloaliphatic/cage hydrocarbon structural units

New high temperature polyaryleneetherketone triphenylphosphine oxides incorporating trans‐1,4‐cyclohexane, 1,3‐adamantane, and 4,9‐diamantane structural units were synthesized by the base‐promoted polymerization reaction between 4,4′‐difluorotriphenylphosphine oxide and the novel dihydroxy monomers trans‐1,4‐bis(4‐hydroxybenzoyl)cyclohexane, 1,3‐bis(4‐hydroxybenzoyl)adamantane, and 4,9‐bis(4‐hydroxybenzoyl)diamantane. The monomers were synthesized in a good yield by a two‐step procedure involving the Friedel–Crafts acylation of anisole by the diacid chlorides trans‐1,4‐cyclohexanedicarbonyl chloride, 1,3‐adamantanedicarbonyl chloride, and 4,9‐diamantanedicarbonyl chloride, followed by demethylation with pyridine hydrochloride. The polymers, which could be processed into tough, free standing films from organic solvents, exhibited high T_g's in the range of 192–239° as well as thermooxidative stabilities (5% weight loss in air) in the range of 445–490°. Preliminary results from a UV–visible spectroscopic study of dilute solutions of the polymers in chloroform showed absorption maxima in the 263–274 nm region and transparency to spectral radiation in the 300–800 nm range, indicating that these triphenylphosphine oxide polymers could have potential applications for space thermal control coatings. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6134–6142, 2004     

Synthesis and characterization of high refractive index polyimides derived from 2,5‐Bis(4‐Aminophenylenesulfanyl)‐3,4‐Ethylenedithiothiophene and aromatic dianhydrides

The authors describe the synthesis and characterization of the polyimide (PI) series containing a 2,5‐bis(4‐aminophenylenesulfanyl)‐3,4‐ethylenedithiothiophene (APSEDTT) moiety in their main chain. The APSEDTT monomer with high sulfur content was prepared and polymerized with several aromatic dianhydrides such as 4,4′‐[p‐thio bis(phenylenesulfanyl)]diphthalic anhydride (3SDEA), 4,4′‐biphthalic anhydride (BPDA), and 4,4′‐oxydiphthalic anhydride (ODPA) by the traditional two‐step polycondensation procedure. All PIs exhibited high transparency, higher than 75% at 550 nm for a thickness of about 20 μm and good thermal properties such as thermal decomposition temperatures (T_10%) in the range of 409–521 °C. In addition, the PIs have extraordinarily excellent optical properties in refractive index and birefringence as originally designed. In particular, the PI derived from APSEDTT and 3SDEA showed a high refractive index (1.7586), and a low birefringence (0.0087) because of their very high sulfur content (27.7%). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 944–950     

Synthesis of novel diene polymer via friedel–crafts‐type reaction of polybutadiene with aromatic compounds

This study describes a novel and facile synthesis strategy for a styrene‐butadiene rubber (SBR)‐like polymer via Friedel–Crafts‐type reaction between aromatic compounds and polybutadiene using an aluminum chloride as a catalyst. Although gelation was induced by a reaction of a generated carbocation with olefins in other polybutadiene chains in benzene and toluene because of their low electron densities on their rings, anisole with a higher electron density reacted with the polybutadiene carbocation efficiently. The introduction ratio of anisole increased as the reaction proceeded, and the obtained polymer, BRAN polymer, contained 15% anisoles for olefins in the polybutadiene in 4 h at 80 °C as estimated by ¹H NMR analysis. The glass‐transition temperature (T_g) of the BRAN polymer also increased with anisole content (T_g ~?50 °C when anisole contents 20%). The vulcanizate containing the BRAN polymer showed higher mechanical properties compared to samples using other matrix polymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 841–847     

Synthesis and characterization of highly refractive polyimides from 4,4′‐thiobis[(p‐phenylenesulfanyl)aniline] and various aromatic tetracarboxylic dianhydrides

An aromatic sulfur‐containing diamine 4,4′‐thiobis[(p‐phenylenesulfanyl) aniline] (3SDA) was synthesized and polymerized with a sulfur‐containing dianhydride 4,4′‐[p‐thiobis(phenylenesulfanyl)]diphthalic anhydride (3SDEA) and three nonsulfur aromatic tetracarboxylic dianhydrides, respectively to afford four poly(amic acid)s (PAAs) with the inherent viscosities of 0.54–1.04 dL/g. Flexible and tough polyimide (PI) films obtained from the PAA precursors showed good thermal, mechanical, and optical properties. The glass transition temperatures (T_gs) of the PIs ranged from 179.1–227.2 °C determined by differential scanning calorimetry (DSC), and 173.8–227.3 °C by dynamic mechanical analysis (DMA), depending on the dianhydride used. The 10% weight loss temperatures were in the range of 500–536 °C, showing high intrinsic thermal‐resistant characteristics of the PI films. The PI films also showed good optical transparency above 500 nm, which agreed well with the calculated absorption spectra using the time‐dependent density functional theory. The average refractive indices (n_av) measured at 632.8 nm were 1.7191–1.7482, and the in‐plane/out‐of‐plane birefringences (Δn) were 0.0068–0.0123. The high refractive indices originate from the high sulfur contents, good molecular packing, and the absence of bulky structures. The relatively small birefringence mainly results from the flexible thioether linkages structures of the diamine. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5606–5617, 2007     

Synthesis and characterization of perfluoro‐3‐methylene‐2,4‐dioxabicyclo[3,3,0] octane: Homo‐ and copolymerization with fluorovinyl monomers

The synthesis of perfluoro‐3‐methylene‐2,4‐dioxabicyclo[3,3,0] octane (D), its radical homopolymerization, and copolymerization with fluoroolefins are presented. Fluorodioxolane (D) was synthesized through direct fluorination of the corresponding hydrocarbon precursor in a fluorinated solvent by F₂/N₂ gas. It was polymerized in bulk using perfluorodibenzoyl peroxide as the initiator. The resulting homopolymer had a limited solubility in fluorinated solvents, and its glass transition temperature (T_g) was in the range of 180–190 °C. The polymeric films prepared by casting from hot hexafluorobenzene (HFB) solution were transparent with low refractive index (1.329 at 633 nm). These films were thermally stable (T_d > 350 °C), and were hard and brittle. The copolymers of monomer (D) were prepared with fluorovinyl monomers such as chlorotrifluoroethylene (CTFE), perfluoropropyl vinyl ether, perfluoromethyl vinyl ether, and vinylidene fluoride. The kinetics of radical copolymerization of monomer (D) with CTFE led to the assessment of the reactivity ratios of both comonomers: r_D = 3.635 and r_CTFE = 0.737 at 74 °C, respectively. The copolymers obtained were soluble in HFB and perfluoro‐2‐butyltetrahydrofuran, with T_g in the range of 84–145 °C depending on the copolymer composition. The films of the copolymers were flexible and clear with a low refractive index (1.3350–1.3770 at 532 nm). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6571–6578, 2009     

Synthesis of highly refractive polyimides derived from 3,6‐bis(4‐aminophenylenesulfanyl)pyridazine and 4,6‐bis(4‐aminophenylenesulfanyl)pyrimidine

A series of aromatic polyimides (PIs) containing pyridazine or pyrimidine in their main chains has been developed. All of the PIs were prepared from newly synthesized diamines, 3,6‐bis(4‐aminophenylenesulfanyl)pyridazine (APP), 4,6‐bis(4‐aminophenylenesulfanyl)pyrimidine (APPM) and aromatic dianhydrides, 4,4′‐[p‐thiobis(phenylenesulfanyl)]diphthalic anhydride (3SDEA) and 4,4′‐oxydiphthalic anhydride (ODPA) via the conventional two‐step polycondensation. The PIs showed good thermal stability with 10% weight loss at temperatures above 450 °C and glass transition temperatures above 190 °C. Films with a 10‐μm thickness exhibited good optical transparency above 80% at 500 nm, high refractive indices ranging from 1.7218 to 1.7499, and low birefringence between 0.0066 and 0.0102. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4886–4984, 2009     

Synthesis of a new monomer N′‐(β‐methacryloyloxyethyl)‐2‐pyrimidyl‐(p‐benzyloxycarbonyl)aminobenzenesulfonamide and its copolymerization with N‐phenyl maleimide

The new monomer N′‐(β‐methacryloyloxyethyl)‐2‐pyrimidyl‐(p‐benzyloxy‐ carbonyl)aminobenzenesulfonamide (MPBAS) (M₁) is synthesized using sulfadiazine as parent compound. It could be homopolymerized and copolymerized with N‐phenyl maleimide (NPMI) (M₂) by radical mechanism using AIBN as initiator at 60 °C in dimethylformamide. The new monomer MPBAS and polymers were identified by IR, element analysis and ¹H NMR in detail. The monomer reactivity ratios in copolymerization were determined by YBR method, and r₁ (MPBAS) = 2.39 ± 0.05, r₂ (NPMI) = 0.33 ± 0.02. In the presence of ammonium formate, benzyloxycarbonyl groups could be broken fluently from MPBAS segments of copolymer by catalytic transfer hydrogenation, and the copolymer with sulfadiazine side groups are recovered. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2548–2554, 2000     

Synthesis and Characterization of Organosilicon Substituted Fluorenyl Derivatives

Friedel‐Crafts cycloalkylation of biphenyl with 2,3‐dichlorobutyltrichlorosilane(Cl₃Si‐CH₂CHClCHClCH₃) at a temperature of 100°C in the presence of anhydrous aluminum chloride catalyst gave cyclized product, 9‐methyl‐9‐(2‐trichlorosilylethyl)fluorene 1a , in 33% yield. Methylation of 1a with nucleophilic reagent such as methyl magnesium chloride, gave 9‐methyl‐9‐(2‐trimethylsilylethyl)fluorene 2 while bromination of 2 with excess amount of bromine in DMF resulted in 2,7‐dibromo‐9‐methyl‐9‐(2‐trichlorosilyl)fluorene 3 in good yield. All the compounds were structurally identified by GC/MS, ¹H and ¹³C‐NMR spectroscopy.     

Nonlinear optical side‐chain polymers post‐functionalized with high‐β chromophores exhibiting large electro‐optic property

Electro‐optic side‐chain polymers have been synthesized by the post‐functionalization of methacrylate isocyanate polymers with novel phenyl vinylene thiophene vinylene bridge (FTC) nonlinear optical chromophores. For this application, FTC‐based chromophores were modified in their electronic donor structure, exhibiting much larger molecular hyperpolarizabilities compared with the benchmark FTC. Of these new chromophores, absorption spectra, hyper‐Rayleigh scattering experiment, and thermal analysis were carried out to confirm availability as effective nonlinear optical units for electro‐optic side‐chain polymers. The electro‐optic coefficients (r₃₃) of obtained polymers were investigated in the process of in situ poling by monitoring the temperature, current flow, poling field, and electro‐optic signal. Compared with the nonsubstituted analogue, benxyloxy modified FTC chromophore significantly achieved higher nonlinear optical property, exhibiting molecular hyperpolarizability at 1.9 μm of 4600 × 10^?30 esu and an r₃₃ value of 150 pm/V at the wavelength of 1.31 μm. Synthesized electro‐optic polymers showed high glass transition temperature (T_g), so that the temporal stability examination exhibited >78% of the electro‐optic intensity remaining at 85 °C over 500 h. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of bio‐based poly(ethylene 2,5‐furandicarboxylate) copolyesters: Higher glass transition temperature,better transparency,and good barrier properties

The bio‐based polyester, poly(ethylene 2,5‐furandicarboxylate) (PEF), was modified by 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol (CBDO) via copolymerization and a series of copolyesters poly(ethylene‐co‐2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol 2,5‐furandicarboxylate)s (PETFs) were prepared. After their chemical structures and sequence distribution were confirmed by nuclear magnetic resonance (¹H‐NMR and ¹³C‐NMR), their thermal, mechanical, and gas barrier properties were investigated in detail. Results showed that when the content of CBDO unit in the copolyesters was increased up to 10 mol%, the completely amorphous copolyesters with good transparency could be obtained. In addition, with the increasing content of CBDO units in the copolyesters, the glass transition temperature was increased from 88.9 °C for PET to 94.3 °C for PETF‐23 and the tensile modulus was increased from 3000 MPa for PEF to 3500 MPa for PETF‐23. The barrier properties study demonstrated that although the introduction of CBDO units would increase the O₂ and CO₂ permeability of PEF slightly, PECF‐10 still showed better or similar barrier properties compared with those of PEN and PEI. In one word, the modified PEF copolyesters exhibited better mechanical properties, higher glass transition temperature, good barrier properties, and better clarity. They have great potential to be the bio‐based alternative to the popular petroleum‐based poly(ethylene terephthalate) (PET) when used as the beverage packaging materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3298–3307     

Solvent‐Vapor‐Induced Reversible Single‐Crystal‐to‐Single‐Crystal Transformation of a Triphosphaazatriangulene‐Based Metal–Organic Framework

A triphosphaazatriangulene (H₃L) was synthesized through an intramolecular triple phospha‐Friedel–Crafts reaction. The H₃L triangulene contains three phosphinate groups and an extended π‐conjugated framework, which enables the stimuli‐responsive reversible transformation of [Cu(HL)(DMSO)?(MeOH)]_n, a 3D‐MOF that exhibits reversible sorption characteristics, into (H₃L?0.5 [Cu₂(OH)₄?6 H₂O] ?4 H₂O), a 1D‐columnar assembled proton‐conducting material. The hydrophilic nature of the latter resulted in a proton conductivity of 5.5×10^?3 S cm^?1 at 95 % relative humidity and 60 °C.     

Synthesis and characterization of spirobifluorene‐based polyimides

The synthesis and properties of organosoluble aromatic polyimides, containing spiro‐skeletal units in the polymer backbone on the basis of the spiro‐diamine monomer, 2,2′‐diamino‐9,9′‐spirobifluorene, are described. In the case of the spiro segment, the two fluorene rings are orthogonally arranged and connected through a tetrahedral bonding carbon atom, the spiro center. As a consequence, the polymer chain is periodically zigzagged with a 90° angle at each spiro center. This structural feature minimizes interchain interactions and restricts the close packing of the polymer chains, resulting in amorphous polyimides that have good solubility in organic solvents. Compared with their fluorene‐based cardo analogues, the spirobifluorene‐based polyimides have an improved solubility. Furthermore, the main‐chain rigidity of the polyimide appears to be preserved because of the presence of the spiro structure, which restricts the free segmental mobility. As a result, these polyimides exhibit a high glass‐transition temperature (T_g's) and good thermal stability. The T_g's of these polyimides were in the range of 287–374 °C, and the decomposition temperatures in nitrogen for a 10% weight loss occurred at temperatures above 570 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3615–3621, 2002     

Copolymers of methyl methacrylate with N‐trifluorophenyl maleimides: High glass transition temperature and low birefringence polymers

Copolymers of methyl methacrylate (MMA) with 2,3,4‐ and 2,4,6‐trifluorophenyl maleimides (TFPMIs) were synthesized by a free radical initiator, azobisisobutyronitrile, in 1,4‐dioxane and also in bulk. The refractive indexes of the copolymers were in the range of 1.49–1.52 at 532 nm. The T_gs were 133–195 °C depending on copolymer compositions. In addition, the copolymers were thermally stable, T_d > 350 °C. The orientational and photoelastic birefringence of the copolymers were also investigated. As both of the orientational and photoelastic birefringences of PMMA are negative, whereas those of poly(TFPMI)s are positive, we could obtain nearly zero orientational and photoelastic birefringence polymers when the ratios of 2,3,4‐TFPMI/MMA were 15/85 and 5/95 mol %, respectively. For 2,4,6‐TFPMI, zero orientational and photoelastic birefringences could be obtained when the ratios of 2,4,6‐TFPMI/MMA were 12/88 and 3/97 mol %, respectively. The T_gs of those copolymers with zero birefringences were in the range of 135–140 °C. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012