共查询到19条相似文献,搜索用时 875 毫秒
1.
2.
3.
4.
5.
6.
中波红外宽带通滤光膜通常膜系层数多,膜层总厚度非常大(厚度达到10 μm左右),膜层的镀制工艺难度较大。通过分析红外带通滤光片几种设计方法的特点,并结合实际镀制工艺技术,采用了长波通与短波通及非规整薄膜设计技术相结合的方法,设计了以锗材料为基底的中波3 μm~5 μm宽带通滤光膜。该设计大幅度降低了膜层的总厚度(约为8.65 μm),缩短了膜层的镀制周期,提高了膜层的牢固度;在膜层的镀制工艺过程中,通过改变薄膜材料的蒸发速率、修正蒸发硫化锌材料时电子枪的扫描方式、调整蒸发材料在坩埚中的装载方法,使膜层获得了优异的光谱性能,其通带平均透过率大于96%,截止区域的平均透过率小于1%。 相似文献
7.
8.
9.
10.
从物理机制上定性地分析了导致脉冲缩短的主要原因,给出了长脉冲重复频率运行下的相对论返波振荡器(RBWO)设计原则。结合传统谐振式返波振荡器的基本设计理论,设计和模拟优化了工作在S波段的长脉冲RBWO,并利用本实验室现有长脉冲脉冲功率驱动源开展了S波段长脉冲RBWO的实验研究。实验结果表明:在单次运行条件下,微波输出功率达到约2 GW、脉宽约90 ns;在10 Hz重复频率运行条件下,输出微波功率达到约1 GW、脉宽约100 ns。器件产生的微波频率为3.6 GHz,输出模式为TM01模,效率约20%。对实验结果分析表明,器件截止颈和第一个慢波结构结合处的爆炸发射是导致脉冲缩短的主要原因之一。 相似文献
11.
研究得出冰蓄冷低温送风空调系统较常规空调系统在风管管路阻力及风管截面积的优越性。依据管路阻力计算公式利用VB语言编写风管比摩阻的计算程序,并利用该计算程序对相同工况下的典型的低温送风温度与常规送风温度的比摩阻进行计算,进而得到风管管路阻力,同时计算得出各送风温度下的风管截面积,并进行对比分析。相同计算条件下,冰蓄冷低温送风空调系统的风管沿程阻力是常规送风系统的40%—70%;采用8℃低温送风方式时,其风管截面积较常规空调可减少20%—30%。与常规空调系统相比,采用冰蓄冷低温送风空调系统可明显减小风管的沿程阻力和截面积,大大降低了风机耗能和建筑层高,节省了运行及建材费用。 相似文献
12.
分时蓄冷时负荷变化大,但可充分利用低谷电来制冰蓄冷,而在高峰时,制冷机不开以融冰供冷,满足空调负荷要求,真正起到在电网中削峰填谷作用。分时蓄冷时,负荷变化大,在融冰循环运行时,流量变化幅度随之变大,情况特殊,因此需要系统要有应对策略。 相似文献
13.
14.
V. A. Zilitis 《Optics and Spectroscopy》2014,116(4):513-515
A new method of data transmission in DWDM systems along existing long-distance fiber-optic communication lines is proposed. The existing method, e.g., uses 32 wavelengths in the NRZ code with an average power of 16 conventional units (16 units and 16 zeros on the average) and transmission of 32 bits/cycle. In the new method, one of 124 wavelengths with a duration of one cycle each (at any time instant, no more than 16 obligatory different wavelengths) and capacity of 4 bits with an average power of 15 conventional units and rate of 64 bits/cycle is transmitted at every instant of a 1/16 cycle. The cross modulation and double Rayleigh scattering are significantly decreased owing to uniform distribution of power over time at different wavelengths. The time redundancy (forward error correction (FEC)) is about 7% and allows one to achieve a coding enhancement of about 6 dB by detecting and removing deletions and errors simultaneously. 相似文献
15.
16.
17.
本文介绍了在YG366高速抛光机上进行的透镜不胶盘单件抛光技术。这一新的抛光方法比弹性成盘法和刚性成盘法有许多优点:它省掉了许多辅助工序,缩短了抛光时间,所以生产周期短,效率高,成本低。同时给出了根据透镜的结构参数进行生产技术准备和评估抛光过程稳定性的公式。最后提出了进一步改进的设想。 相似文献
18.
利用LNG冷能的混合工质中低温热力循环开拓研究 总被引:11,自引:1,他引:10
为提高中低温余热回收动力系统性能,本文在常规混合工质热力循环(火用)分析基础上,提出了结合LNG冷能利用的新型混合工质热力循环。通过与LNG的有机结合,混合工质热力循环热效率提高14.5个百分点,(火用)效率达到53.6%。为进一步揭示效率提高的原因,我们比较了常规混合工质热力循环与LNG-混合工质热力循环的(火用)损失变化情况。结果表明:LNG-混合工质热力循环高效的关键在于循环平均放热温度的降低以及工质蒸发过程与冷凝过程换热的合理匹配。而LNG冷能的梯级利用则是系统具有较高(火用)效率的根本原因。 相似文献
19.
The objective of this study is to find out the factor that accounts for the capacity fading and to predict the cycle life of lithium-ion batteries by the driving cycle test. A new method, incremental polarization resistance, is elected to analyze the gradation mechanism based on incremental capacity analysis. It is summarized that the two major factors, the loss of lithium ions and the cathode fading, make the capacity loss in different stages. In the first stage, the loss of lithium ions, caused by the solid electrolyte interface (SEI) lay reaction, is the main reason for battery degradation. In the second stage, the cathode starts to decay and make the capacity loss, because of the less intercalation in cathode. In the third stage, the cathode degradation gradually outpaces the loss of Li and becomes the limit factor for the battery recession. Finally, a cycle life model was established to predict the capacity loss with cycle numbers. 相似文献