pH和盐对树脂吸附芳香酸的影响研究

通过三甲胺修饰超高交联聚苯乙烯树脂NJ-00制备了一种新型树脂(NJ-03),树脂性质表征说明,通过改性季胺基被成功引入,树脂骨架上增加了一定数量的碱性基团。研究了pH、盐浓度对芳香酸类化合物在NJ-03树脂上吸附的影响,并与商品大孔强碱阴离子交换树脂D-201以及大孔弱碱阴离子交换树脂D-301进行对比,探讨了pH和盐浓度影响吸附的机理。     

THE SEPARATION，PURIFICATION AND DECOLORIZATION OF NEW ANTIBIOTICS—MILUPEINAN USING ADSORPTION RESIN

Adsorption resin AAS was used for the separation and purification of milupeinan (M-13)from its mother liquor. The good adsorption property of AAS adsorption resin was found formilupeinan (M-13) compared with the Diaion CHP 20p. When acetone and water (2:1 in volume)were used as desorption reagents, it was found that 3 times of bed volume of the desorption reagentswould make the AAS resin which was saturately adsorpted M-13 desorption completely.Also a macroporous anion exchange resin (Poly-4-vinylpyridine type) D-280 was used for thedecolourization from M-13 solution. Good results was given when the sr=1～2.     

THE SEPARATION,PURIFICATION AND DECOLORIZATION OF NEW ANTIBIOTICS-MILUPEINAN USING ADSORPTION RESIN

1. INTRODUCTION Fig.1 The Chemical Structure of Milupeinan As a new type of antibiotics Milupeinan, not only possesses antibacterial activities against a wide range of Gram-positive and Gram-negative bacteria, but also higgh stability under th…     

树脂法分离纯化米洛培南

采用国产AAS大孔吸附树脂及D－280大孔脱色树脂对抗生素米洛培南制备母液进行分离纯化。实验表明，与日本Diaion公司生产的Diaion CHP20相比，AAS大孔吸附树脂对米洛培南具有更优良的吸附性能，使用D－280大孔脱色树脂对抗生素米洛培南制备母液进行脱色，未发现类似报道，分析结果证实，以上述方法制备的抗生素米洛培南收率高，纯度高，各项分析数据与文献报道相符。     

Synthesis and characterization of pyridyl anion exchange resin for 99Tc removal

Journal of Radioanalytical and Nuclear Chemistry - A new pyridyl anion exchange resin (PS-N) was synthesized by chloroacetylation and quaternization on the polystyrene-divinylbenzene microspheres...     

球形纤维素磁性阴离子交换树脂的化学转化制备及特性研究

自制了大孔球形纤维素基阴离子交换树脂(PSC-AN),并利用化学转化法成功制备了大孔球形纤维素基磁性阴离子交换树脂(PSC-MAN)。对影响树脂质量磁化率的几个主要因素进行了探讨,实验确定最佳制备条件为:铁盐的配比为1∶10,EDTA的浓度为0.005 mol/L。对树脂的结构和性能进行了研究,表明化学转化法制备大孔球形纤维素基阴离子交换树脂(PSC-MAN)磁性强,在碱液中相当稳定,树脂磁化前后交换容量分别为Q前=1.33 meq/g、Q后=1.16 meq/g,即树脂基的交换容量基本不受磁化过程的影响。     

含长碳链间隔臂结构的强碱性阴离子交换树脂的合成及热稳定性

研究了一种含长碳链间隔臂结构的强碱性阴离子交换树脂的新合成方法.评价了该树脂在水中的热稳定性.结果表明,以苯乙烯-二乙烯基苯共聚白球和1,3-噁嗪-2-酮为原料,季铵型离子液体为催化剂,得到带有胺丙基的苯乙烯-二乙烯基苯共聚珠体,再用甲酸和甲醛N-甲基化,溴乙烷季铵化,可以生成强碱交换量为1.86mmol/g强碱阴离子交换树脂.含长碳链间隔臂结构的OH~-型阴离子交换树脂在100℃去离子水中保持720h交换量仅下降11.83%,好于商业通用的强碱阴离子交换树脂.     

同时吸附油和六价铬离子复合材料的制备及性能

以亲油疏水型三元乙丙橡胶(EPDM)作为基体, 焙烧Fe2O3和阴离子交换树脂201Х7作为填料, 利用熔融共混的方法, 制备一种可以同时吸附油和六价铬离子的用于污水处理的复合材料, 这种材料能够悬浮于油水界面处. 当焙烧Fe2O3和阴离子交换树脂的用量比例不同时, 材料吸附性能变化很大. 实验结果表明, 在保证复合材料密度介于油水密度之间的前提下, 随着焙烧Fe2O3含量的增加, 材料的吸油性能不断增大; 随着阴离子交换树脂含量的增加, 材料对六价铬的吸附性能不断增加. 在油水共存体系中, 复合材料对两种污染物的吸附率同时达到最佳时, 两种填料的比例可以确定, 因油品的不同而不同. 在油水共存体系中, 复合材料对油和六价铬的总吸附能力要远大于复合材料分别在单一吸附介质中的吸附能力.     

PAR螯合形成树脂特性的研究

我们曾报导了用D-290阴离子树脂与4-(2-吡啶偶氮)-间苯二酚(PAR)制得PAR螯合形成树脂,简称PAR树脂。其形成不同于一般的螯合形成树脂。从而扩大了获得这类树脂的领域。本文对它的特性进行了研究。     

弱碱性阴离子交换树脂分离1,6—二磷酸果糖的研究

采用弱碱性阴离子交换树脂HJ-30对发酵液中1，6-二磷酸果糖的分离进行了研究。详细地研究了树脂的吸附和脱附性能。实验结果表明，HJ-30树脂对FDP的吸附量达0．28gFDP／g湿树脂，以0．05mol／LNaCl洗脱光机磷和1mol／LNaCl洗脱1，6-二磷酸果糖，产品的收率和纯度分别为92％和99．4％。     

阴离子交换树脂回收水相中有机磷酸萃取剂

研究了阴离子交换树脂对水相中有机磷酸萃取剂的吸附。 通过比较不同的离子交换树脂对水相中2-乙基己基膦酸-单-2-乙基己基酯(P507)的去除率,发现大孔强碱性阴离子交换树脂(D201-OH)从水溶液中去除P507的能力最强,去除率可达99.24%。 而且当溶液在pH=1.0时,D201-OH对P507的吸附主要是分子吸附,其吸附等温线更适用于Langmuir模型;当溶液在pH=5.0时,阴离子交换反应占主导地位,其吸附等温线更适用于Freundlich模型。 研究还表明,D201-OH对P507的吸附在20 min内即达到吸附平衡时99.8%的吸附量。 通过动力学研究表明,拟一级动力学模型(R²>0.99)更适用于描述实验数据,并且吸附速率主要受膜扩散控制。 此外,吸附-解吸附循环8次后,D201-OH的吸附能力仍然保持在93%以上。 综上所述,D201-OH是有机磷酸类萃取剂的良好吸附剂,其吸附性能高效,循环过程稳定,因此可用于实际生产过程中回收有机磷酸萃取剂。     

Adsorption of phenol from water by N-butylimidazolium functionalized strongly basic anion exchange resin

N-butylimidazolium functionalized strongly basic anion exchange resin with Cl(-) anion (MCl) was prepared by anchoring N-butylimidazole onto chloromethylated macroporous styrene-divinylbenzene (St-DVB) copolymer. The adsorption performances of phenol on MCl were studied using the batch technique at acidic and alkaline pH. The studies showed that phenol can be effectively removed at both acidic and alkaline pH. The maximum adsorption was achieved at about pH 11. The maximum adsorption capacities of phenol on MCl at pH 6.6 and 11.2 were 80.2 and 92.9 mg/g, respectively. The adsorption mechanism was mainly molecular adsorption at acidic pH and anion exchange at alkaline pH. The adsorption of phenol was hindered by the presence of Cl(-) and SO(4)(2-) at alkaline pH due to the competitive anion exchange reaction. The adsorption of molecular phenol species on MCl at acidic pH was exothermic, and the anion exchange of phenolate species by MCl at alkaline pH was endothermic. Desorption of phenol from loaded adsorbent was achieved by using 0.5 mol/L NaOH and 0.5 mol/L NaCl mixed solution. MCl can simultaneously remove phenol and Cr(VI) from their mixtures, which would be of practical value in actual industrial wastewater treatment.     

Preparation and application of a novel magnetic anion exchange resin for selective nitrate removal

正A novel magnetic anion exchange resin NDM-1 was prepared through suspension polymerization and then functionalized with ammonolysis and alkylating agents.Its application for selective removal of nitrate was performed in comparison with MIEX~.The results demonstrated that NDM-1 achieved higher efficiency in nitrate removal than MIEX~ did,with or without the existence of competing anion SO_4~(2-) ascribed to its longer alkyl chains on exchange sites.Combined with the advantage of easy separation due toγ-Fe_2O_3 implanted,the magnetic anion exchange resin NDM-1 was considered to be superior to MIEX~ for nitrate removal in practical application.     

330阴离子交换树脂对草甘膦的吸附性能

采用静态吸附法研究了330阴离子交换树脂对水中草甘膦的吸附性能,并研究了吸附动力学;测定了溶液的pH值、温度、NaCl含量等因素对330树脂吸附草甘膦的影响.结果表明:330树脂对水中草甘膦的吸附速率快;在pH=2.69时对草甘膦的吸附性能最好;330树脂对草甘膦的吸附是放热、自发的过程,吸附等温线符合Freundli...     

INTERACTION MECHANISM OF ORGANIC MATTER WITH GEL TYPE POLYSTYRENE STRONGLY BASIC ANION EXCHANGE RESIN AND REGENERATION OF THE ORGANISM FOULED RESIN Ⅰ．The interreaction mechanism between strongly basic anion exchange res

ＩＮＴＥＲＡＣＴＩＯＮＭＥＣＨＡＮＩＳＭＯＦＯＲＧＡＮＩＣＭＡＴＴＥＲＷＩＴＨＧＥＬＴＹＰＥＰＯＬＹＳＴＹＲＥＮＥＳＴＲＯＮＧＬＹＢＡＳＩＣＡＮＩＯＮＥＸＣＨＡＮＧＥＲＥＳＩＮＡＮＤＲＥＧＥＮＥＲＡＴＩＯＮＯＦＴＨＥＯＲＧＡＮＩＳＭＦＯＵＬＥＤＲＥＳ...     

D-101树脂对胭脂虫红色素吸附特性的研究

绘制了胭脂虫红色素的标准曲线,从9种不同性质的大孔吸附树脂中筛选出D-101树脂用于分离胭脂虫红色素,研究了D-101树脂对胭脂虫红色素吸附动力学曲线和不同温度下的吸附等温线。实验结果表明:胭脂虫红色素溶液浓度与吸光度之间显示良好的线性关系;D-101树脂对胭脂虫红色素的吸附速率快,120min达到平衡,吸附量为143.17mg/g树脂,吸附动力学曲线符合二级吸附动力学模型;D-101树脂对胭脂虫红色素的吸附等温线符合Freundlich方程,低温有利于吸附;通过热力学计算得到H、G、S均小于0,说明吸附是放热过程且能自发进行,吸附后体系趋向有序。研究结果可为胭脂虫红色素的分离提供有益的参考。     

8-Quinolinol-5-sulfonic acid-loaded resin as a preconcentrating agent in the neutron activation analysis of the chalcophile elements (author's transl)]

A chelating agent-loaded resin consisting of 8-quinolinol-5-sulfonic acid and an anion-exchange resin (HOx-resin) was prepared in order to concentrate trace chalcophile elements in natural water samples selectively before neutron activation analysis. The exchange capacity of the Diaion SA No. 100 for the reagent (1.8 meq . g-1 resin) corresponds approximately to that for chloride ion (1.83 meq . g-1 resin), indicating that 8-quinolinol-5-sulfonic acid is adsorbed quantitatively on the exchange site of the resin through the sulfonate anion in the reagent. The basic conditions for the adsorption of the metal ions on the resin were investigated by employing the column method. The nitrate concentration and the pH of the sample solution affect the adsorption behavior of metal ions. Several solutions containing metal ions with varying pH or varying nitrate concentration were applied to the resin column (35 mm x 7 mm phi) with a flow rate of 2.0 cm3 . min-1. As a result, the optimum conditions for the quantitative adsorption of copper(II), zinc(II), cadmium(II), cobalt(II), nickel(II) and manganese(II) were as follows: NO3- less than 0.01 mol . dm-3 pH greater than 4.6. Furthermore, the feasibility of the above conditions as well as quantitative adsorption of the chalcophile elements was confirmed through the neutron activation analysis of the synthesized metal solutions.     

Adsorption of Zinc and Cyanide from Cyanide Effluents on Anionic Ion-exchange Resin

The adsorption of zinc and cyanide from cyanide effluents onto strong and weak basic anion exchange resins was studied in a batch adsorption system. Factors influencing the adsorption rates such as resin selection, resin amounts, contact time and temperature were studied and scanning electron microscopy-energy disperse spectroscopy(SEM-EDS) was used in the analysis. The present study shows that the adsorption capacity of resin 201×7 is better than that of resin 301. The adsorption process was relatively fast and came to equilibrium after 60 min. The kinetic data were analyzed with three models and the pseudo-second-order kinetic model was found to agree with the experimental data well. The equilibrium data could also be described well by Langmuir isotherm model. Thermodynamic parameters such as enthalpy change(ΔH⁰), free energy change(ΔG⁰) and entropy change(ΔS⁰) were calculated and the adsorption process was spontaneous and endothermic.     

Adsorption Behavior of Metal Ions by Amidoxime Chelating Resins

In this work, the acrylonitrile (AN) – divinylbenzene (DVB) –methylacrylate (MA) resin was synthesized via suspension polymerization in the presence of toluene as diluent, and benzoylperoxide (BPO) as initiator. The effect of MA, toluene and alkaline treatment on the exchange capacity of the resin were investigated. The results showed that the anion exchange capacity decreased with an increase in the amount of MA, while alkaline treatment had no significant effect. Also, the cation exchange capacity increased with an increase in the amount of hydrophilic agent and reached a maximum point. The sorption equilibrium was achieved relatively fast within 40 mins, and the resin exhibited affinity towards lead (II), copper (II) and in particular uranium (VI). The adsorption of uranium was directly depended up on the pH value. Furthermore, the macroreticular chelating resin, containing amidoxime group had higher adsorption of uranium (VI) in comparison to other metal ions studied. Finally, the alkaline treatment enhanced the potential for much faster adsorption characteristics and the highly porous chelating resin provided a more favorable pore structure for the rapid rate of diffusion of metal ions.     

Micellization and Adsorption to Carbon Black of Polyisobutylene-Based Ionic Liquids

Ionic liquid-terminated polyisobutylene (PIB-IL) dispersants suitable for stabilization of carbonaceous deposits found in automotive lubricating oils were derived by the quaternization of tertiary amines (1-methyl-imidazole, pyridine, and isoquinoline) with primary bromide-terminated PIB. Characterization of PIB intermediate and PIB-IL dispersants was carried out by nuclear magnetic resonance, gel-permeation chromatography, thermogravimetric analysis (TGA), matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, and differential scanning calorimetry. PIB-IL micellization in dodecane and characteristics thereof (hydrodynamic radius, aggregation number, and critical micelle concentration) were investigated by static (SLS) and dynamic light scattering; whereupon, the self-association of PIB-IL was found to be highly sensitive to anion hydrophobicity. Qualitative adsorption of PIB-IL onto carbon black was confirmed by Fourier transform infrared and TGA measurements. Using Langmuir adsorption studies, the affinity for and adsorption to carbon black of PIB-IL were characterized. PIB-IL adsorption onto carbon black occurred via cation–π interactions and was identified to be highly dependent on the molar volume of the cation and independent of the anion. From the parameters obtained by the Langmuir adsorption isotherms, the spatial arrangement of PIB-IL on the carbon black surface was elucidated, in which all adsorbed PIB-IL were determined to exist in the elongated brush regime. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 280–299