GeO2-La2O3-TiO2玻璃的结构、热学和光学性质(英文)

La₂O₃-TiO₂玻璃以其折射率高、光学性能优异,在透镜、光学窗口、光通信等领域具有广阔的应用前景。受限于玻璃形成能力,人们难以制备出大尺寸La₂O₃-TiO₂玻璃,这严重限制其应用。本研究通过引入网络形成体GeO₂,有效提高了玻璃形成能力,从而可用常规方法制备大尺寸的GeO₂-La₂O₃-TiO₂(GLT)玻璃。差热分析表明,GLT玻璃具有较高的玻璃转变温度和抗析晶性能,玻璃转变温度T_g和ΔT(ΔT=T_c-onset–T_g)分别大于833和209℃。最大折射率为2.06,在可见光和近红外波段的透过率可达78%。实验还研究了Ti含量对GLT玻璃结构、热学和光学性能的影响。结果表明,随着钛含量增加,玻璃的形成能力和热稳定性均减弱。摩尔体积V_m和氧离子极化率α     

具有自洁和耐磨功能SiO2/TiO2减反膜的制备与研究

以正硅酸乙酯(TEOS)和钛酸正丁酯(TBOT)为原料,采用溶胶-凝胶法制备了SiO2溶胶和TiO2溶胶,利用浸渍提拉法制备了SiO2/TiO2双层减反膜.用紫外-可见分光光度计(UV-Vis)、X射线衍射仪(XRD)、扫描电子显微镜(SEM)、原子力显微镜(AFM)、椭圆偏振光谱仪和接触角测量仪等分析表征了薄膜的特性,以光催化降解甲基橙溶液实验来评价薄膜的自洁功能,考察了SiO2/TiO2双层减反膜的耐磨擦性.结果表明,SiO2/TiO2双层减反膜在400~800nm可见光波段的透光率最高可达97.2%,薄膜表面平整,结构致密且粗糙度小,经紫外灯照射后薄膜的水接触角接近0°,光催化2h后可将5mg/L的甲基橙溶液降解43.6%.SiO2/TiO2减反膜还具有优良的耐磨擦性能.     

自清洁SiO2/TiO2减反膜的制备与性能研究

采用溶胶-凝胶技术制备了SiO₂溶胶和TiO₂溶胶,利用浸渍提拉法在光伏玻璃上制备了SiO₂/TiO₂减反膜。用光谱透射比测量仪和椭偏仪测定了薄膜的透光率和折射率,通过场发射扫描电子显微镜观察了薄膜的形貌结构,最后考察了薄膜的自洁性能和耐候性能。结果表明：随着溶胶中TiO₂浓度的升高,SiO₂/TiO₂减反膜的厚度不断增加,而透光率逐渐减小,折射率逐渐增大。在波长为600nm时,TiO₂浓度最低的减反膜(ST-300)的透光率为94.4%,折射率为1.33。ST-300减反膜的表面平整,结构致密。光催化2h后,ST-300减反膜可将10mg/L的甲基蓝溶液降解11.2%,经过耐候处理后,其透光率衰减值仅0.08%～0.15%。     

环境净化功能TiO2/SiO2复合纳米粉体的制备与表征

以锐钛矿型TiO2纳米粉体为载体,Na2SiO3为包覆剂,H2SO4为中和剂,采用溶胶-凝胶法制备了系列环境净化功能TiO2/SiO2复合纳米粉体.用XRD、XRF、TEM、BET比表面分析对其进行了表征,并以亚甲基蓝溶液的光催化降解率和COD去除率为指标评价了其光催化活性.结果表明,在TiO2纳米颗粒表面包覆一层多孔非晶态水合二氧化硅纳米膜,可以显著提高其水分散性,有效控制其光催化活性,进而提高了涂料的抗老化性和耐候性.中和时间对包硅效率影响较大,适当增加中和时间有利于提高包硅效率;包覆温度对包硅效率影响较小,升高温度使包硅效率略有降低.低温包覆,成膜相对疏松,改性粉体的光催化活性相对较高;高温包覆,成膜相对致密,改性粉体的光催化活性相对较低.     

SiO2-TiO2/聚四氟乙烯复合材料的制备及热膨胀性能

为了使微波基板材料与Cu金属衬底的热膨胀性能匹配,对陶瓷/聚四氟乙烯（PTFE）微波复合基板材料的热膨胀性能进行了研究。采用湿法工艺制备了以SiO₂和TiO₂为填料的SiO₂-TiO₂/PTFE复合材料,研究了复合材料密度、填料粒度和填料体积分数对SiO₂-TiO₂/PTFE复合材料热膨胀性能的影响。结果表明,当SiO₂的体积分数由0增至40%（TiO₂ ：34%~26%）时,SiO₂-TiO₂/PTFE复合材料的线膨胀系数（CTE）由50.13×10^-6 K^-1减小至10.03×10^-6K^-1。陶瓷粉体粒径和复合材料密度减小会导致CTE减小。通过ROM、Turner和Kerner模型计算CTE发现,ROM和Kerner模型与实验数据较相符,而实验值与Turner模型预测值之间的差异随PTFE含量的升高而逐渐增大。     

SiO2-TiO2 复合微粒的研究

通过溶胶法制备了18nm 和40nm 两种粒径均匀、单分散的SiO₂2TiO₂ 复合微粒, 确定了最佳合成条件。电镜照片显示, 水和TiO₂ 粒子接枝于SiO₂ 粒子表面, 成针状向外生长。对包覆过程、复合纳米粉末煅烧行为、表面改性的研究表明, 1100℃～ 1200℃TiO₂ 由锐钛型向金红石型转变, SiO₂ 的鳞石英晶型也开始形成。甲醇改性的TS纳米粉末能较好的再分散于乙醇中。      

SiO2/聚四氟乙烯复合薄膜的制备及力学性能

采用空气辅助干法共混、冷压烧结并车削成膜的方法制备了SiO₂填充量为35wt%、厚度为50 μm的聚四氟乙烯（PTFE）基复合薄膜。系统研究了SiO₂颗粒粒径对SiO₂/PTFE薄膜复合材料的孔洞缺陷和力学性能等的影响,并研究了SiO₂在PTFE中的分散情况及分子间相互作用对其性能变化的影响机制。结果表明,随SiO₂粒径的逐渐增大,其在PTFE中的分散趋于均匀,同时PTFE能更好地包覆粒子,因此SiO₂/PTFE薄膜孔洞缺陷逐渐减少,力学性能逐渐增强;当SiO₂的粒径D₅₀为12 μm时,其在PTFE中的分散均匀性最佳,SiO₂/PTFE复合薄膜孔洞缺陷最少,具有较好的力学性能,断裂伸长率达19.5%,拉伸强度达9.2 MPa。      

TiO2纳米丝的制备

通过阳极氧化制备了多孔性氧化铝膜,并以其为模板,采用溶胶凝胶法制得了TiO2纳米丝.     

纳米TiO2/SiO2负载棉织物的制备及其光催化降解染料的研究

将纳米TiO_2水溶胶和纳米SiO_2水溶胶复配制备环境净化整理剂,并通过轧烘焙工艺对棉织物进行后整理得到纳米TiO_2/SiO_2负载棉织物,然后将其用于不同结构有机染料的光催化降解反应中,重点考察纳米SiO_2的添加量对其在不同pH值反应体系中的光催化降解性能以及重复利用性的影响。结果表明,纳米TiO_2/SiO_2负载棉织物对不同结构的有机染料具有显著的光催化降解性能,能够促进染料分子的共轭体系和芳香环结构的降解反应。纳米SiO_2的添加不仅有利于纳米TiO_2/SiO_2负载棉织物在碱性介质中光催化降解性能的提高,而且也能够改善其重复利用性。     

膜层厚度对Ag/TiO膜透光隔热性能的影响

采用磁控溅射工艺制备了玻璃基Ag/TiO_2膜,并研究了膜层厚度对其透光隔热性能的影响。结果表明:当Ag膜厚度由6.7 nm增加到9.5 nm时,红外光的平均透过率由42.06%减小到7.70%,隔热温差由1.9℃增大到5.7℃,而可见光的平均透过率则呈现出先增加后减少的变化趋势,当Ag膜厚度为7.7 nm时,复合膜的可见光平均透过率达最大值,为70.85%;当Ti O_2膜厚度由4.1 nm增加到16.7 nm时,红外光的平均透过率由34.12%增大到38.28%,而可见光的平均透过率与隔热温差均呈现出先增大后减少的变化趋势,当Ti O_2膜厚度为10.4 nm时,复合膜的可见光平均透过率达最大值,为70.85%,而厚度为13.6 nm时,膜的隔热温差达最大值,为5.2℃。     

纳米TiO_2-WO_3复合涂层及纳米TiO_2/WO_3叠层涂层的制备及性能

为了解决电子池材料改性TiO2涂层暗态下无阴极保护作用的问题,用溶胶-凝胶法及浸渍提拉技术在304不锈钢表面制备了纳米TiO2-WO3复合涂层与纳米TiO2/WO3叠层涂层,用扫描电镜(SEM)、X射线光电子能谱仪(XPS)研究了2种涂层的表面形貌、成分,并用电化学方法研究了2种涂层的光阴极保护特性及耐腐蚀性能。结果表明:2种涂层表面均连续均匀,由Ti,W,O,C组成;紫外光照1 h时2种涂层均对304不锈钢有一定的光阴极保护作用,闭光后纳米TiO2/WO3叠层涂层的延时阴极保护作用远好于纳米TiO2-WO3复合涂层;2种涂层均对304不锈钢有防腐蚀作用,紫外光照射时纳米TiO2-WO3复合涂层的防腐蚀性比纳米TiO2/WO3叠层涂层的好。     

Reactive sputtering of SiO2-TiO2 thin film from composite Six/TiO2 targets

Coatings of SiO₂-TiO₂ films are frequently used in a number of optical thin film applications. In this work we present results from depositing films with variable Si/Ti ratios prepared by reactive sputtering. The different Si/Ti ratios were obtained by varying the target composition of composite single targets. Compared to co-sputtering this facilitates process control and composition uniformity of the films. Varying the oxygen supply during sputter deposition can result in films ranging from metallic/substoichiometric to stoichiometric oxides. Transmittance spectra of the different films are presented and the optical constants are determined from these spectra. Furthermore, the deposition process, films structure and composition of the films are discussed. The study shows that by choosing the right composition and working in the proper oxygen flow range, it is possible to tune the refractive index.     

Effect of the SiO2/TiO2 ratio on the solid acidity of SiO2-TiO2/montmorillonite composites

SiO₂-TiO₂/montmorillonite composites with varying SiO₂/TiO₂ molar ratios were synthesized and the effect of the SiO₂/TiO₂ ratio on the solid acidity of the resulting composites was investigated. Four composites with SiO₂/TiO₂ molar ratios of 0, 0.1, 1 and 10 were synthesized by the reaction of colloidal SiO₂-TiO₂ particles prepared from alkoxides with sodium-montmorillonite at room temperature. The composites showed slight expansion and broadening of the XRD basal reflection, corresponding to the intercalation of fine colloidal SiO₂-TiO₂ particles into the montmorillonite sheets and incomplete intercalation to form disordered stacking of exfoliated montmorillonite and colloidal SiO₂-TiO₂ particles. The colloidal particles crystallized to anatase in the low SiO₂/TiO₂ composites but remained amorphous in the high SiO₂/TiO₂ composites. The specific surface areas (S_BET) of the composites measured by N₂ adsorption ranged from 250 to 370 m²/g, considerably greater than in montmorillonite (6 m²/g). The pore size increased with decreasing SiO₂/TiO₂ molar ratio of the composites. The NH₃-TPD spectra of the composites consisted of overlapping peaks, corresponded to temperatures of about 190 and 290 °C. The amounts of solid acid obtained from NH₃-TPD were 186-338 μmol/g in the composites; these values are higher than in the commercial catalyst K10 (85 μmol/g), which is synthesized by acid-treatment of montmorillonite. The present sample with SiO₂/TiO₂ = 0.1 showed the highest amount of acid, about four times higher than K10.     

静电纺丝法制备尼龙-6/SiO2-TiO2杂化纳米纤维

采用静电纺丝法结合溶胶凝胶技术,制备了尼龙-6/SiO2-TiO2杂化纳米纤维。采用红外光谱（FT-IR）、X射线衍射（XRD）、UV-vis、热重分析（TG）和扫描电镜（SEM）等对杂化纳米纤维进行分析表征。结果表明,随着SiO2-TiO2溶胶的引入,电纺纤维的结晶度下降,耐热性能提升。尼龙-6电纺纤维的平均直径约为...     

Natural and persistent superhydrophilicity of SiO2/TiO2 and TiO2/SiO2 bi-layer films

Sol-gel SiO₂/TiO₂ and TiO₂/SiO₂ bi-layer films have been deposited from a polymeric SiO₂ solution and either a polymeric TiO₂ mother solution (MS) or a derived TiO₂ crystalline suspension (CS). The chemical and structural properties of MS and CS bi-layer films heat-treated at 500 °C have been investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscospy. Water contact angle measurements show that MS SiO₂/TiO₂ and CS TiO₂/SiO₂ bi-layer films exhibit a natural superhydrophilicity, but cannot maintain a zero contact angle for a long time over film aging. In contrast, CS SiO₂/TiO₂ bi-layer films exhibit a natural, persistent, and regenerable superhydrophilicity without the need of UV light. Superhydrophilic properties of bi-layer films are discussed with respect to the nature of the TiO₂ single-layer component and arrangement of the bi-layer structure, i.e. TiO₂ underlayer or overlayer.     

Preparation of 3-dimensional SiO2 structures via a templating method

Three-dimensional (3D) SiO₂ has been prepared by coating silica on the surface of a template polymer and a sequent calcination of the silica/polymer composite. The template polymer that has 3D skeletal structure was prepared by curing epoxy resin in polyethylene glycol mediums using diethylenetriamine as a curing agent. The coating of silica on the polymer surface was accomplished through a slow in situ hydrolysis of infiltrated ethyl silicate in the interconnected pore network of the template polymer. The thickness of silica layer was controlled in a range of 20-80 nm by changing the total amount of ethyl silicate in hydrolysis. The 3D structures of silica were characterized by scanning electronic microscopy, transmitting electronic microscopy, Fourier transform infrared spectroscopy and surface area measurement. The light scattering of the 3D silica filled with liquid medium can be minimized by tuning the refractive index of the liquid medium to be the same as that of amorphous silica in the 3D structure.     

SiO2 / Ni 核壳结构纳米粒子的制备及其磁性能

以硅酸钠为主要原料, 通过液相沉淀法在纳米镍粉表面包覆了一层SiO₂ 。应用XRD、FTIR、TEM、TGA、DSC 和VSM 对复合粉体的结构、形貌和磁性能进行了研究。结果表明, SiO₂ 以非晶态的形式包覆在纳米镍粒子表面, 形成了核壳结构, 降低了纳米粉体的团聚现象。TGA 和DSC 结果表明, SiO₂ 的包覆提高了纳米粉体的抗氧化性。磁性分析结果表明, 粉体包覆前由于表面氧化层(NiO) 的存在, 粉体的磁滞回线偏移; 包覆后的粉体由于SiO₂的存在, 饱和磁化强度降低, 矫顽力升高。      

Preparation of SiO2/TiO2 composite fibers by sol-gel reaction and electrospinning

Submicron scale composite fibers of SiO₂/TiO₂ with various compositions have been prepared by electrospinning a sol-gel precursor of tetraethyl orthosilicate(TEOS) and titanium(IV) isopropoxide(TiP), followed by calcination. Any gelator or binder has not been used in this direct preparation process for composite fibers, and the maximum amount of titania for suitable fiber formation was about 50 mol%. The sintered composite fibers were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) spectroscopy. Our results show that the surface morphology and crystallization behavior of electrospun fibers are largely influenced by the calcination temperature and the content of TiO₂. XRD results also reveal that the anatase phase in composite fibers can be preserved even after high temperature processing at lower content (x = 0.1, 0.2) of titania.