Sr2Si5N8∶Eu2+荧光粉的制备与发光性能

以α-Si₃N₄,SrCO₃,Eu₂O₃为原料,采用碳热还原氮化法制备了Sr₂Si₅N₈∶Eu²⁺荧光粉。研究了材料的结构与光谱特性,分析了影响材料发光性能的工艺因素。结果表明,石墨粉含量和助熔剂的用量对Sr₂Si₅N₈相的形成和发光性能有重要影响。当n_C/n_Sr=1.5,助熔剂用量为4wt%时,合成样品的主晶相为正交晶系Sr₂Si₅N₈,在400~550 nm可见光激发下,可发射峰值波长位于609 nm荧光。激发带的位置与Eu²⁺离子浓度无关,为400~550 nm之间的宽带激发;但发射强度随Eu²⁺离子浓度的增加而增加,Eu²⁺离子浓度达到5mol%时发射强度达最大值,在Eu²⁺离子浓度为2mol%~5mol%之间,观察到发射峰的红移现象。     

SrAl2O4∶Eu2+，Dy3+长余辉材料发光性能与温度依赖研究

对SrAl₂O₄∶Eu²⁺,Dy³⁺长余辉材料在100~500 K温度之间的发光性能进行研究。实验结果表明,材料的荧光及余辉强度在特定温度区间内呈线性变化,在热释峰所在温度范围具有较好的发光性能。其变化规律表明SrAl₂O₄∶Eu²⁺,Dy³⁺长余辉材料内部陷阱中电子的释放包括瞬时释放和延时释放两种类型,其中电子瞬时释放进而跃迁发光是荧光的组成部分,延时释放产生的跃迁则导致余辉发光。陷阱和电子的复合与陷阱中电子释放过程均随温度升高而增强,但温度过高时会发生热猝灭。材料荧光强度与余辉强度在特定温度区间内随温度呈线性变化关系表明其可以作为一种光纤温度传感材料。     

纳米SrAl2O4∶Eu2+，Dy3+长余辉发光材料的制备与性能

采用水热-均匀共沉淀法制备了纳米SrAl₂O₄∶Eu²⁺,Dy³⁺长余辉发光材料。通过XRD、TEM、荧光光谱、热释光谱对其结构和性能进行分析。XRD结果表明所制备的SrAl₂O₄∶Eu²⁺,Dy³⁺纳米发光材料为单相,属单斜晶系。TEM测试表明纳米SrAl₂O₄∶Eu²⁺,Dy³⁺发光材料为规则的球状粒子,粒径为50~80 nm,且分散性良好。激发和发射光谱测试表明,样品的激发光谱是峰值在356 nm的连续宽带谱,发射光谱是峰值位于512 nm的宽带谱,与SrAl₂O₄∶Eu²⁺,Dy³⁺粗晶材料相比,激发和发射光谱都出现了“蓝移”现象。样品的热释光峰值位于358 K,适合于产生长余辉。     

一维Y2O3∶Eu3+纳米发光材料的制备与表征

One-dimensional Y₂O₃∶Eu³⁺ luminescence nanomaterials were prepared by hydrothermal method without template, and their properties were characterized. XRD patterns show that the precursors are hexagonal phase Y(OH)₃ crystals, and the samples are cubic Y₂O₃ after heat-treatment. SEM images indicate that the one-dimensional material with a diameter of 100 nm and length of micrometer scale can be obtained by this hydrothermal method. Photoluminescence properties show that the position and intensity of the precursors are different with that of the heat-treated samples resulted from the different hosts.     

蓝色长余辉材料CaAl2O4:Eu2+,Nd3+的合成及其发光性能

采用高温固相法合成了系列单相Ca(1-x-y)Al2O4:Eu2+x,Nd3+y(0≤x≤0.045,0≤y≤0.0037)粉末样品,并表征了其发光特性.研究结果表明,样品的发射光谱为最大发射峰位于440nm的宽带谱,属于Eu2+的4f65d→4f7跃迁.通过对Eu2+,Nd3+掺杂量与样品发光性能之间关系的研究发现,Eu2+和Nd3+最佳掺杂量分别为x=0.00125和y=0.0025,并且Nd3+对改善蓝色长余辉材料CaAl4:Eu2+的余辉性能具有重要的作用.在最佳掺杂条件下,样品的余辉时间可达1000min,初始亮度大于1200mcd/m2,60min后发光粉的亮度仍然在10mcd/m2以上.利用正电子湮灭技术和热释光技术,研究了Eu2+和Nd3+对CaAl2O4:Eu2+,Nd3+材料的发光性能的影响.     

Eu3+在Ba2TiSi2O8中的发光

The barium titano-silicate phosphors doped with Eu³⁺ were synthesized by high temperature solid state reaction. The structures of as-synthesized samples were characterized by powder XRD. The maximum peaks of emission spectra of Ba₂TiSi₂O₈ and Ba₂TiSi₂O₈∶Eu³⁺ were respectively located at 450 and 618 nm, coming from the transitions of charge-transfer bands of Ti⁴⁺-O^2- and forced electric-dipole transition ⁵D₀-⁷F₂ of Eu³⁺. The luminous mechanisms of Ba₂TiSi₂O₈ and Ba₂TiSi₂O₈∶Eu³⁺ were suggested. The effects of concentration of Eu³⁺ on the luminous performance of Ba₂TiSi₂O₈∶Eu³⁺ were also studied and the results showed that the optimum concentration of Eu³⁺ was 0.12 mol per mole of matrix.     

Eu2+、Mn2+、Sr2+掺杂BaMgAl10O17的燃烧法合成及光致发光性能研究

在600℃温度下,采用液相燃烧法合成了Sr²⁺、Eu²⁺和Mn²⁺三掺的BaMgAl₁₀O₁₇（BAM）蓝绿荧光粉。用XRD、SEM和荧光光谱仪分别分析和表征该荧光粉的物相、形貌和光致发光性能。结果表明,液相燃烧法合成BAM的温度明显低于传统的高温固相合成法;合成的纳米棒均匀、无团聚现象;荧光光谱仪分析表明Eu²⁺、Mn²⁺离子间存在能量传递,且Sr²⁺能有效提高BAM的发光强度,约为固相法制备荧光强度的1.8倍。BAM：0.1Eu²⁺,0.04Mn²⁺,0.05Sr²⁺色坐标为（0.146,0.250）,属于蓝绿光。     

水热法制备具有光滑表面的球形Y2O3∶Eu3+发光材料

The spherical Y₂O₃∶Eu³⁺ luminescent particles with size of 0.5～3 μm and smooth surface were synthesized by hydrothermal method. The resulted Y₂O₃∶Eu³⁺ precursors and the calcined particles were characterized by differential thermal analysis (DTA) and thermogravimetric (TG) analysis, X-ray diffraction (XRD), Fourier-transform IR spectroscopy (FTIR), scanning electron microscopy (SEM) and photoluminescence spectra (PL). FTIR, TG-DTA, XRD measurements show that the precursors are crystal with hydroxyl and carbonate group, and the pure cubic yttria is obtained after annealing above 700 ℃. The SEM images indicate that the Y₂O₃∶Eu³⁺ particles are in spherical shape and with smooth surface. PL analysis shows that the particles present characteristic red emission of Eu³⁺.     

SrAl2O4∶Eu2+，Dy3+纳米长余辉发光材料的制备与表征

采用溶胶-凝胶法制备了SrAl₂O₄∶Eu²⁺，Dy³⁺ 纳米长余辉发光材料，研究了pH值、反应温度和络合剂等对溶胶-凝胶形成的影响，研究了灼烧温度对SrAl₂O₄∶Eu²⁺，Dy³⁺ 晶相、颗粒尺度和发光性能的影响。利用XRD, SEM，光谱分析等手段对产物进行了结构和性能分析。实验结果表明，在800 ℃时SrAl₂O₄晶相开始形成但没有发光，而在1 100 ℃烧结的样品则具有很好的发光性能。样品平均晶粒尺寸随灼烧温度升高而增加，平均晶粒尺寸为20～40 nm。样品的激发光谱是峰值在240，330，378和425 nm的连续宽带谱，发光光谱是峰值在523nm的宽带谱，与SrAl₂O₄∶Eu²⁺，Dy³⁺ 粗晶材料相比，发光光谱发生了“红移”现象。样品的热释光峰值位于157 ℃，与SrAl₂O₄∶Eu²⁺，Dy³⁺ 粗晶材料相比，峰值向低温移动了13℃。     

共沉淀-熔盐法制备BaMoO4∶Eu3+及其发光性能研究

以KCl-NaCl为熔盐,采用共沉淀前躯体-熔盐辅助焙烧法合成了红色发光材料BaMoO₄∶Eu³⁺。运用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)及荧光光谱(PL)等测试手段,研究了熔盐辅助焙烧温度对粉体相结构、形貌和发光性能的影响,并对比了直接采用共沉淀法合成BaMoO₄∶Eu³⁺的结构与发光性能。结果表明：采用两种方法制备的BaMoO₄∶Eu³⁺均是纯相,粒径随温度升高而增大。当KCl-NaCl复合熔盐焙烧温度大于700 ℃,BaMoO₄晶粒在熔盐中实现了(111)面取向生长,得到均一的尖晶石型BaMoO₄∶Eu³⁺微晶。光谱研究表明：共沉淀前躯体-熔盐辅助焙烧法合成样品在615 nm处的Eu³⁺的⁵D₀-⁷F₂发射明显得到加强,样品发出明亮的红色发射光。     

钙长石中镓置换骨架铝对结构和Eu~(2+)发光特性的影响

采用高温固相法在弱还原气氛下制备了Ca0.955Al2-xGaxSi2O8∶Eu2+(x=0～1.0)系列荧光粉,研究了Ga3+置换Al3+对晶体结构和光谱特性的影响。Ga3+以类质同相替代CaAl2Si2O8晶格中的Al3+形成连续固溶体,晶胞参数a,b,c和晶胞体积V随Ga3+置换量呈线性增大;晶面夹角α,β和γ随Ga3+置换量的增加呈线性递减。荧光激发谱为宽带,位于230～420 nm,可拟合成4个峰,表观峰值位于352 nm;随着Ga3+置换量的增加,半高宽从112 nm减小到98 nm。发射光谱位于375～560 nm,可由421和457 nm两峰拟合而成,表观峰值位于425 nm,随着Ga3+置换量的增加,两拟合峰均线性红移,且拟合峰强度比呈线性递减。     

Si5P6O25∶Tb3+的结构与荧光性质

Tb³⁺ ions were incorporated in P-Si matrix material through a sol-gel process. Luminescence properties of Tb³⁺ as a function of dopant， firing temperature， composition and structure of matrices were investigated. The gels synthesized by the reaction of P₂O₅ or H₃PO₄ with tetraethoxy silane and TbCl₃ as dopant were fired in air from the temperature 25～1000℃ to form P-Si crystalline phase. The crystal structure was determined by powder X-ray diffraction. Si₅O(PO₄)₆ were the only crystalline phase and belong to hexagonal crystal system. The emission of ⁵D₄-⁷F₅(～545nm) transition of Tb³⁺ in the P-Si system is composed of two peaks. The amount of doping Tb³⁺ varied from 0.664% to 1.644%， and no obvious concentration quenching was observed in this doping concentra-tion range. The intensity of Tb³⁺ emission increased with firing temperature increasing and becomes stable at 800～1000℃.     

纳米BaAl2S4:Eu2+发光材料的制备及性能

采用溶胶-凝胶法合成了纳米荧光粉BaAl2S4:Eu2+, 并对其性能进行了研究.     

ZnO-B2O3∶Tb3+长余辉玻璃的发光性质

通过还原方法制备了Tb³⁺离子掺杂的硼酸锌玻璃，并观察到在254 nm紫外光激发后有明亮的绿色长余辉发光现象，余辉时间达6 h。通过激发与发射光谱、余辉光谱、余辉衰减曲线、热释光谱、热释光释出速率衰减曲线等得到的信息，研究了Tb³⁺离子掺杂的硼酸锌玻璃的发光性质。     

SrAl2O4：Eu2+，Dy3+的助熔剂法制备及其发光特性

以B₂O₃为助熔剂，在1 350 ℃、还原性气氛下成功制备了SrAl₂O₄单相粉末样品。用同样的方法制备了系列单相Sr_1-x-yAl₂O₄：Eu²⁺_x，Dy³⁺_y·nB₂O₃(0.005≤x≤0.07， 0.01≤y≤0.05，0.05≤n≤0.25)样品并表征了其长余辉发光特性。结果表明，最佳的Eu²⁺含量为0.02。辅助激活离子Dy³⁺在Sr_0.98Al₂O₄：Eu²⁺_0.02中的掺杂在一定范围内可以显著提高亮度和余辉时间，最佳Dy³⁺含量为0.03。研究不同B₂O₃含量对Sr_0.95Al₂O₄：Eu²⁺_0.02，Dy³⁺_0.03发光性能的影响，结果说明最佳的B₂O₃含量为n=0.1，余辉肉眼可见(≥0.32 mcd·m^-2)时间达4 000 min。利用正电子湮灭技术和热释光技术，研究和讨论了B₂O₃对Sr_0.95Al₂O₄：Eu²⁺_0.02，Dy³⁺_0.03的发光和余辉性能的影响，结果表明B₂O₃的添加有助于Dy³⁺在晶格中形成深度合适、有益于余辉的空位缺陷。     

Crystal Structure of SrAl2B2O7 and Eu Luminescence

The crystal structure of strontium dialuminodiborate SrAl₂B₂O₇ has been established by single-crystal X-ray diffraction methods. The compound crystallizes in the trigonal system (space group R c, Z=6) with cell parameters a=4.893(1) Å and c=47.78(1) Å. Aluminium and boron atoms are, respectively, in tetrahedral and triangular oxygen coordination. The assembly of Al₂O₇ units and BO₃ triangles forms double layers between which Sr²⁺ ions are located. The Eu²⁺-doped crystalline powder exhibits a luminescence band with maximum at 415 nm. Luminescence characteristics are compared to those of other strontium borates.     

Ca掺杂的Ba2Al2Si10N14O4:Eu2+荧光粉发光性能

通过固相反应制备了系列Ca掺杂的Ba2Al2Si10M14O4:Eu2+色荧光粉,发现当半径较大的Ba被Ca取代后导致了晶格的收缩,通过X射线衍射(XRD)测量和Unitcell软件计算发现Ca的最大掺杂量在20％.Ca掺人Eu0.4Ba1.6Al2Si10N14O4荧光粉后,可有效地提高光转换性能,并使激发光谱发生一定程度的红移和宽化,从而被近紫外宽波段光有效激发,与近紫外LED的发射光谱匹配.同时Ca的掺杂也使发射光谱发生了可控的红移,可以由520 nm的绿光红移至548 nm的黄光区域.进一步发现Eu2+的淬灭浓度随着20％ Ca的掺入而降低,这是由于Ca掺入导致的晶格收缩使Eu2+离子间距离减小.最后在CIE色度图中对不同Ca,Eu浓度的荧光粉的色坐标位置进行比较,发现可通过Ca,Eu浓度的变化在很大范围内调制荧光粉的发光性能.     

铽(Ⅲ)、铕(Ⅲ)-1-环丙基-6-氟-7(1-哌嗪基)1、4-二氢-4-氧喹啉-3-羧酸-乙酰丙酮三元固体荧光配合物的合成与光谱表征

Two ternary solid complexes， Tb³⁺ (Eu³⁺)-ciprofloxacina-acetylacetone， have been synthesied and chara-cterized by elemental analysis， IR. Ciprofloxacina is one kind of bacteriophage containing α-carbonyl carboxylic acid configurayion and acetylacetone contains β-diketonate configurayion. They are the ideal ligands for Tb³⁺ and Eu³⁺. The fluorescence spectra of Tb³⁺ and Eu³⁺ complexes showed that the ligands were suitable for efficient energy transfer from ligands to the Tb³⁺ or Eu³⁺ ion with a high fluorescence quantum yield， large stoke shift， narrow emission bonds and large fluorescence lifetime. So the complexes were the new kind of solid fluorescence materials. Moreover， the mechanisms of the fluorescence of Tb³⁺ (Eu³⁺)-ciprofloxacina-acetylacetone ternary solid complex were investigated.     

Ca10(Si2O7)3Cl2:Eu2+Mn2+单-基质白光荧光粉的发光性质

用高温固相法合成了颜色可调的Ca10(Si2O7)3Cl2:Eu2+Mn2+荧光粉.研究了它的发光性质和Eu2+与Mn2+之间的能量传递.Eu2+离子在Ca10(Si2O7)3Cl2晶体中形成了峰值为426 nm和523 nm的5d→4f跃迁发光,Eu2+中心向Mn2+中心传递能量,敏化Mn2+离子4T1(4G)-6A1(6S)跃迁而产生585 nm的黄光发射.黄绿蓝3个发射带叠加在单一基质中实现了白光发射.3个发射带的激发谱范围位于250-480 nm处,Ca10(Si2O7)3Cl2:Eu2+Mn2+在紫外-近紫外波段(350～410 nm)范围内有很强的激发,是一种适合InGaN管芯激发的单一基质白光LED荧光粉.