Effect of oxygen pressure on microstructure and magnetic properties of strontium hexaferrite (SrFe12O19) film prepared by pulsed laser deposition

The effects of oxygen pressure during deposition on microstructure and magnetic properties of strontium hexaferrite (SrFe₁₂O₁₉) films grown on Si (100) substrate with Pt (111) underlayer by pulsed laser deposition have been investigated. X-ray diffraction pattern confirms that the films have c-axis perpendicular orientation. The c-axis dispersion (Δθ₅₀) increases and c-axis lattice parameter decreases with increasing oxygen pressure. The films have hexagonal shape grains with diameter of 150-250 nm as determined by atomic force microscopy. The coercivities in perpendicular direction are higher than those in in-plane direction, which shows the films have perpendicular magnetic anisotropy. The saturation magnetization and anisotropy field for the film deposited in oxygen pressure of 0.13 mbar are comparable to those of the bulk strontium hexaferrite. Higher oxygen pressure leads to the films having higher coercivity and squareness. The coercivity in perpendicular and in-plane directions of the film deposited in oxygen pressure of 0.13 mbar are 2520 Oe and 870 Oe, respectively.     

Preparation of strontium hexaferrite film by pulsed laser deposition with in situ heating and post annealing

Strontium hexaferrite (SrFe₁₂O₁₉) films have been fabricated by pulsed laser deposition on Si(1 0 0) substrate with Pt(1 1 1) underlayer through in situ and post annealing heat treatments. C-axis perpendicular oriented SrFe₁₂O₁₉ films have been confirmed by X-ray diffraction patterns for both of the in situ heated and post annealed films. The cluster-like single domain structures are recognized by magnetic force microscopy. Higher coercivity in perpendicular direction than that for the in-plane direction shows that the films have perpendicular magnetic anisotropy. High perpendicular coercivity, around 3.8 kOe, has been achieved after post annealing at 500 °C. Higher coercivity of the post annealed SrFe₁₂O₁₉ films was found to be related to nanosized grain of about 50–80 nm.     

Properties of Dy-doped ZnO nanocrystalline thin films prepared by pulsed laser deposition

Highly transparent conductive Dy₂O₃ doped zinc oxide (ZnO)_1-x(Dy₂O₃)_x nanocrystalline thin films with x from 0.5% to 5% have been deposited on glass substrate by pulsed laser deposition technique. The structural, electrical and optical properties of Dy₂O₃ doped thin films were investigated as a function of the x value. The experimental results show that the Dy concentration in Dy-doped ZnO thin films has a strong influence on the material properties especially electrical properties. The resistivity decreased to a minimum value of 5.02 × 10⁻⁴ Ω cm with x increasing from 0.5% to 1.0%, then significantly increased with the further increasing of x value. On the contrary, the optical direct band gap of the (ZnO)_1-x(Dy₂O₃)_x films first increased, then decreased with x increasing. The average transmission of Dy₂O₃ doped zinc oxide films in the visible range is above 90%.     

On the optical properties of amorphous Ge-Ga-Se-KBr films prepared by pulsed laser deposition

Amorphous thin films (1 − x)(4GeSe₂-Ga₂Se₃)-xKBr (x = 0, 0.1, 0.2, 0.3) were prepared by the pulsed laser deposition (PLD) technique. The optical parameters were calculated using the Swanepoel method from the optical transmission spectra. The optical band gap () of the studied films increased while the index of refraction decreased when increased the content of KBr. The Tauc slopes were discussed as an indicator of the degree of structural randomness of amorphous semiconductors. The index of refraction decreased and increased after annealing of as-deposited films below the glass transition temperature. The thermal-bleaching and thermal- contraction effects were observed, which are discussed in relation to the reduction in the density of homopolar bonds confirmed by the Raman spectra analysis and the decreased amount of fragments of the as-deposited films, respectively.     

Homogeneous films by inverse pulsed laser deposition

Recently, we proposed an alternative arrangement to traditional on- or off-axis PLD geometries, termed inverse PLD (IPLD) that is capable of producing films of improved surface morphology. Two configurations of this new target-substrate arrangement were developed, namely static and co-rotating IPLD. In the static IPLD configuration, the substrate is stationary with respect to the ablated spot; while in the co-rotating IPLD configuration the substrate is fixed to the target surface and rotates simultaneously with the target, hence offering an appealingly simple approach to homogenize film properties.Here we report the growth of CN_x and Ti films, simultaneously deposited in the co-rotating and static IPLD arrangements. The homogeneity of the co-rotating films is described by a thickness inhomogeneity index, which allows for the comparison of films of different lateral dimension. A semi-analytical, semi-numerical model is proposed to derive the radial variation of the growth rate of co-rotating IPLD films from the lateral growth rate distributions measured along the symmetry axes of static IPLD films. The laterally averaged growth rate, LAGR is used to describe how the ambient pressure affects growth in the 0.5-50 Pa domain. As an example, the absolute error between the measured and calculated radial growth rate variation, obtained at 5 Pa, was less than 3%, while the LAGR of CN_x layers grown by co-rotating IPLD was predicted with 20% accuracy.     

Oxygen reduction activity of N-doped carbon-based films prepared by pulsed laser deposition

Carbon-based films with nitrogen species on their surface were prepared on a glassy carbon (GC) substrate for application as a non-platinum cathode catalyst for polymer electrolyte fuel cells. Cobalt and carbon were deposited in the presence of N₂ gas using a pulsed laser deposition method and then the metal Co was removed by HCl-washing treatment. Oxygen reduction reaction (ORR) activity was electrochemically determined using a rotating disk electrode system in which the film samples on the GC substrate were replaceable. The ORR activity increased with the temperature of the GC substrate during deposition. A carbon-based film prepared at 600 °C in the presence of N₂ at 66.7 Pa showed the highest ORR activity among the tested samples (0.66 V vs. NHE). This film was composed of amorphous carbons doped with pyridine type nitrogen atoms on its surface.     

Optical and electrical properties of aluminum-doped ZnO thin films grown by pulsed laser deposition

Transparent aluminum-doped zinc oxide (AZO) thin films were deposited on quartz glass substrates by pulsed laser deposition (PLD) from ablating Zn-Al metallic targets. The structural, electrical and optical properties of these films were characterized as a function of Al concentration (0-8 wt.%) in the target. Films were deposited at a low substrate temperature of 150 °C under 11 Pa of oxygen pressure. It was observed that 2 wt.% of Al in the target (or 1.37 wt.% of Al doped in the AZO film) is the optimum concentration to achieve the minimum film resistivity and strong ultraviolet emission. The presence of Al in the ZnO film changes the carrier concentration and the intrinsic defects.     

An investigation into the effects of high laser fluence on hydroxyapatite/calcium phosphate films deposited by pulsed laser deposition

Pulsed laser deposited mixed hydroxyapatite (HA)/calcium phosphate thin films were prepared at room temperature using KrF laser source with different laser fluence varying between 2.4 J/cm² and 29.2 J/cm². Samples deposited at 2.4 J/cm² were partially amorphous and had rough surfaces with a lot of droplets while higher laser fluences showed higher level of crytallinity and lower roughness of surfaces of obtained samples. Higher laser fluences also decreased ratio Ca/P of as-deposited samples. X-ray photoelectron spectroscopy (XPS) revealed traces of carbonate groups in obtained samples, which were removed after thermal annealing. The decomposition of HA into TCP was observed to start at about 400 °C. The formation of new crystalline phase of HA was found after annealing as well. The cracks observed on surface of sample deposited at 29.2 J/cm² after annealing indicated that the HA/ calcium phosphate films deposited at higher laser energy densities were probably more densed.     

Role of vanadium content in ZnO thin films grown by pulsed laser deposition

Vanadium-doped ZnO films (Zn_1−xV_xO, where x = 0.02, 0.03, 0.05 and 0.07), were formed from ceramic targets on c-cut sapphire substrates using pulsed laser deposition at substrate temperature of 600 °C and oxygen pressure of 10 Pa. In order to clarify how the vanadium concentration influences the films’ properties, structural and magnetic investigations were performed. All films crystallised in wurtzite phase and presented a c-axis preferred orientation at low concentrations of vanadium. The results implied that the doping concentration and crystalline microstructure influence strongly the system's magnetic characteristics. Weak ferromagnetism was registered for the film with the lowest doping concentration (2 at.%), which exhibited a ferromagnetic behavior at Curie temperature higher than 300 K. Increasing the vanadium content in the film caused degradation of the magnetic ordering.     

Non-stoichiometry-induced metal-to-insulator transition in nickelate thin films grown by pulsed laser deposition

While controlling the cation contents in perovskite rare-earth nickelate thin films, a metal-to-insulator phase transition is reported. Systematic control of cation stoichiometry has been achieved by manipulating the irradiation of excimer laser in pulsed laser deposition. Two rare-earth nickelate bilayer thin-film heterostructures with the controlled cation stoichiometry (i.e. stoichiometric and Ni-excessive) have been fabricated. It is found that the Ni-excessive nickelate film is structurally less dense than the stoichiometric film, albeit both of them are epitaxial and coherent with respect to the underlying substrate. More interestingly, as a temperature decreases, a metal-to-insulator transition is only observed in the Ni-excessive nickelate films, which can be associated with the enhanced disproportionation of the Ni charge valence. Based on our theoretical results, possible origins (e.g. anti-site defects) of the low-temperature insulating state are discussed with the need of future work for deeper understanding. Our work can be utilized to realize unusual physical phenomena (e.g. metal-to-insulator phase transitions) in complex oxide films by manipulating the chemical stoichiometry in pulsed laser deposition.     

Preparation and characterization of pulsed laser deposition (PLD) SiC films

Si K-edge XAFS was used to characterize a stoichiometric SiC film prepared by pulsed KrF laser deposition. The film was deposited on a p-type Si(1 0 0) wafer at a substrate temperature of 250 °C in high vacuum with a laser fluence of ∼5 J/cm². The results reveal that the film contains mainly a SiC phase with an amorphous structure in which the Si atoms are bonded to C atoms in its first shell similar to that of crystalline SiC powder but with significant disorder.     

Electrical, structural, and optical properties of ITO thin films prepared at room temperature by pulsed laser deposition

Indium tin oxide (ITO) thin films were prepared by pulsed laser deposition (PLD) on glass substrate at room temperature. Structural, optical, and electrical properties of these films were analyzed in order to investigate its dependence on oxygen pressure, and rapid thermal annealing (RTA) temperature. High quality ITO films with a low resistivity of 3.3 × 10⁻⁴ Ω cm and a transparency above 90% were able to be formed at an oxygen pressure of 2.0 Pa and an RTA temperature of 400 °C. A four-point probe method, X-ray diffraction (XRD), atomic force microscopy (AFM), and UV-NIR grating spectrometer are used to investigate the properties of ITO films.     

Enhanced photoluminescence of rare-earth doped films prepared by off-axis pulsed laser deposition

Alternate pulsed laser deposition from the host (Al₂O₃) and dopant (Er, Yb) targets has been used to prepare artificially nanostructured films in which the rare earth ion-ion separation is controlled in the nanometer scale in order to control energy transfer between ions. One series of films was prepared in the standard on-axis configuration, i.e. a static substrate being centred with respect to the plasma expansion axis. A second series of films was prepared by rotating the substrate with respect to a shifted axis parallel to the plasma expansion one (off-axis configuration). The latter configuration leads to films with enhanced thickness and Er related photoluminescence intensity uniformity. More interestingly, the Er related photoluminescence lifetime in as-grown films increases up to 2.5 ms, which is much higher than the maximum value of 1 ms obtained for the on-axis configuration films. This enhancement is discussed in terms of a decrease of defect density when using the off-axis configuration.     

Fabrication of p-type Li-doped ZnO films by pulsed laser deposition

p-Type ZnO thin films have been realized via doping Li as acceptor by using pulsed laser deposition. In our experiment, Li₂CO₃ was used as Li precursor, and the growth temperature was varied from 400 to 600 °C in pure O₂ ambient. The Li-doped ZnO film prepared at 450 °C possessed the lowest resistivity of 34 Ω cm with a Hall mobility of 0.134 cm² V⁻¹ s⁻¹ and hole concentration of 1.37 × 10¹⁸ cm⁻³. X-ray diffraction (XRD) measurements showed that the Li-doped ZnO films grown at different substrate temperatures were of completely (0 0 2)-preferred orientation.     

Magnetic/non-magnetic nanoparticles films with peculiar properties produced by ultrashort pulsed laser deposition

Films of magnetic nanoparticles uniformly mixed with non-magnetic nanoparticles have been produced by ultrashort pulsed laser deposition. These films present innovative characteristics with respect to their counterparts produced by standard techniques, as for example nanosecond laser ablation or sputtering, due to the peculiar shape and preferential distribution of their constituent nanoparticles. In the present investigation, the difficult coalescence among the deposited nanoparticles, specific characteristic of the ultrashort pulsed laser deposition, is particularly stressed for what concerns its effect on the collective magnetic behaviour. In particular, we observed that, even for a significant fraction of magnetic particles, the films exhibit an unusual high remanent magnetization, together with relatively low values of saturation and coercive fields, showing a strong squareness of the hysteresis loops. In perspective, these nanogranular films appear very promising for potential application as permanent magnets and in magnetic recording.     

Atomic force microscopic characterization of films grown by inverse pulsed laser deposition

Carbon nitride films have been deposited by KrF excimer laser ablation of a rotating graphite target in 5 Pa nitrogen ambient in an inverse pulsed laser deposition configuration, where the backward motion of the ablated species is utilised for film growth on substrates lying in the target plane. Topometric AFM scans of the films, exhibiting elliptical thickness distribution, have been recorded along the axes of symmetry of the deposition area. High resolution AFM scans revealed the existence of disk-like, or somewhat elongated rice-like features of 5-10 nm average thickness and ∼100 nm largest dimension, densely packed over the whole, approximately 14 × 10 cm² deposition area. The RMS roughness of the film decreased from 9 nm near to the laser spot down to 2 nm in the outer regions. Even the highest RMS value obtained for IPLD films was less than half of the typical, 25 nm roughness measured on simultaneously deposited PLD films.     

Structure and refractive index dispersive behavior of potassium niobate tantalate films prepared by pulsed laser deposition

Pure perovskite phase and crack-free KTa_0.5Nb_0.5O₃ thin films were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. The structure and orientation were analyzed by X-ray diffraction. The optical properties were investigated by an ellipsometer. The relationship between the refractive index dispersive behavior and internal structure was analyzed by Sellmeier dispersion model and single electronic oscillator approximation. The parameters of room temperature monomial Sellmeier oscillator were calculated. And the refractive index dispersive parameter E₀/S₀ of KTa_0.5Nb_0.5O₃ thin films on Pt/Ti/SiO₂/Si substrates is (6.72 ± 0.04) × 10⁻¹⁴ eV m², which is consistent with those of KTN crystals and compounds with ABO₃ perovskite type structure.     

Characterization of polymer thin films obtained by pulsed laser deposition

The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate).The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry.It was found that for laser fluences up to 1.5 J/cm² the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm² the polyepichlorohydrin films present deviations from the bulk polymer.Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm²).The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material.The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.     

Room temperature growth and properties of ZnO films by pulsed laser deposition

ZnO thin films were prepared by pulsed laser deposition at room temperature on glass substrates with oxygen pressures of 10-30 Pa. The structural, electrical, and optical properties of ZnO films were studied in detail. ZnO films had an acceptable crystal quality with high c-axis orientation and smooth surface. The resistivity was in the 10² Ω cm order for ZnO films, with the electron concentration of 10¹⁶-10¹⁷ cm⁻³. All the films showed a high visible transmittance ∼90% and a high UV absorption about 90-100%. The UV emission ∼390 nm was observed in the photoluminescence spectra. The oxygen pressures in the 10-30 Pa range were suitable for room temperature growth of high-quality ZnO films.