欧盟国家燃煤电厂环保政策及技术路线分析

温室气体的排放控制作为全球性的环境问题受到了广泛关注。中国是火力发电的大国,其燃煤机组的温室气体排放总量巨大。《火电厂大气污染物排放标准》（GB 13223-2011）提高了我国燃煤电厂的烟气污染物排放的要求,对火电厂烟气处理的技术选择和投资都会产生重大影响。针对中国燃煤电厂环保面临的新形势,阐述了欧盟国家的环保政策重点,并对欧盟国家燃煤电厂污染物控制的相关标准进行了分析,同时简要介绍了欧盟国家燃煤电厂环保的主要技术路线,在一定程度上可作为中国燃煤电厂污染物控制的借鉴和参考。     

火电厂大气污染物排放标准之管见

本文将《火电厂大气污染物排放标准》（ＧＢ１３２２３－１９９６）与原《燃煤电厂大气污染物排放标准》（ＧＢ１３２２３－９１）在多方面作了比较，从环保管理者的角度，分析了新标准对电力建设与污染治理产生的影响，对今后在执行新标准的过程中可能遇到的问题提出了一些见解。     

发电集团应对燃煤电厂超低排放的思考

新的《火电厂大气污染排放标准》全面加大了对火电厂大气污染物中烟尘、SO2、NOx的控制力度,收严了污染物排放限值。近期提出的煤电节能减排升级与改造行动计划,进一步提出了燃煤电厂达到燃气机组排放标准的超低排放要求。解读了燃煤电厂推行超低排放的一些政策支撑、技术路线,从华电集团超低排放技术及应用实例出发,对超低排放技术实施过程中需要关注的问题进行了探讨,具有一定的参考价值。     

内地与香港燃煤电厂大气污染物排放控制政策与标准比较

香港特区与广东省政府联合成立粤港持续发展与环保合作小组,并发表《改善珠江三角洲空气质量的联合声明》（简称＂减排联合声明＂）,同意制定合理的减排方案,共同执行管理计划。总结分析了粤、港地区在治理燃煤电厂大气污染物方面的控制政策,并对大陆与香港特区燃煤电厂大气污染物的排放标准进行比较。     

燃煤电厂汞排放分析及控制技术研究

新的《火电厂大气排放标准》的颁布实施,燃煤电厂汞的排放正式纳入控制标准。针对目前我国燃煤电厂汞排放化学形态转换、排放特征,分析和总结现有污染控制设施对汞协同控制效果,提出适合我国国情的燃煤电厂汞控制技术措施的建议及发展趋势,可有效控制燃煤电厂汞的排放量。     

燃煤电厂汞排放及其控制技术研究

燃煤电厂汞排放是最大的人为汞污染源,《火电厂大气污染物排放标准》(GB 13223-2011)首次提出了我国燃煤发电锅炉汞及其化合物的控制指标,规定汞及其化合物排放限值为0.03 mg/m3.介绍了国内外汞污染发展情况,汞的形态以及汞污染控制技术.汞控制技术主要分为三种:燃烧前脱汞、燃烧中脱汞和燃烧后脱汞,其中燃烧后脱汞的研究最广泛.     

《火电厂大气污染物排放标准》重新修订实施

为贯彻实施新修订的《火电厂大气污染物排放标》(GB13223-2003)(以下简称《排放标准》)，有效控制火电厂大气污染物排放，2004年5月21日国家环保总局就有关要求通知如下：     

石油炼制行业新旧污染物排放标准的差异

分别介绍了旧标准GB 8978—1996《污水综合排放标准》、GB 16297—1996《大气污染物综合排放标准》和新标准GB 31570—2015《石油炼制工业污染物排放标准》的核心内容。从适用范围、排放限值和污染控制因子3个方面分析了石油炼制行业新旧污染物排放标准的差异。     

稀土氧化物催化还原烟气中的SO2

在实验室研究结果的基础上,建立了小型实际燃煤烟气脱硫试验装置,采用实际燃煤烟气进行了稀土氧化物催化还原烟气脱硫的试验,考察了空速、反应温度对脱硫率的影响。试验结果表明,在反应温度520～550℃、空速2800h。的条件下,脱硫率为99％,NOx的去除率为95％,SO2最高排放质量浓度为100mg／m^3,NOx最高排放质量浓度为50mg／m^3,符合GB13223-2003《火电厂大气污染物排放标准》2时段标准,与实验室的实验结果基本吻合。     

二个大气污染物排放标准中计算方法比较

就《火电厂大气污染物排标准》（ＧＢ１３２２３－１９９６）和《制定地方大气污染物排放标准的技术方法》（ＧＢ／Ｔ１３２０１－９１）两个国家标准的污染物允许排放量计算公式进行了比较，指出了它们的差异及适用范围。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Heavy Metals Removal by Biosorption and Flotation

The removal of a mixture of heavy (toxic) metal cations (copper, nickeland zinc) from liquid effluents was investigated in this study at pilotscale, using counter-current contact mode. The innovative processinvolved the abstraction of metal ions onto fungal biosorbents, followedby the application of flotation for the subsequent solid/liquid separationof biomass particles. The ability of microorganisms to remove metal ionsfrom aqueous solutions is a well-known phenomenon. Nevertheless,engineering considerations are very important in decisions, concerningthe commercial future of biosorption and practical solutions are neededfor certain problems, such as the efficient post-separation ofmetal-loaded biomass. The two processes (flotation and biosorption) caneffectively operate in combination, in what it was termed biosorptiveflotation process. The sorbents may be recycled, after appropriate elutionof metals, as well as the treated (clean) water.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Selection of Autochthonous Plant Species from SE Spain for Soil Lead Phytoremediation Purposes

Mining activity in SE of Spain, in the west Mediterranean coast, originated more than two millenniums ago. It has generated huge areas affected by heavy metals contamination, especially of lead, which is possibly one of the most important. Investigations related to the selection of autochthonous plant taxa from a typical Spanish Mediterranean area, useful for phytoextraction and phytostabilization purposes in these polluted areas are shown. Under these edaphoclimatic conditions 12 interesting species were considered, from them six taxa were chosen for further studies. Some plant species have been proposed either for phytoextraction or phytostabilization purposes. Recommendations for further research have been discussed.