Flexible All‐Solid‐State Supercapacitors of High Areal Capacitance Enabled by Porous Graphite Foams with Diverging Microtubes

The practical applications of wearable electronics rely on the successful development of flexible and integrable energy devices with small footprints. This work reports a completely new type of graphite foam made of strategically created superstructures with covalently attached diverging microtubes, and their applications as electrode supports for binder‐free and additive‐free flexible supercapacitors. Because of the enhanced volumetric surface areas compared to conventional graphite foams, a high loading of pseudocapacitive materials (Mn₃O₄, 3.91 mg cm^?2, 78 wt%) is achieved. The supercapacitors provide areal capacitances as high as 820 mF cm^?2 at 1 mV s^?1, while still maintaining high rate capability and 88% retention of capacitance after 3000 continuous charging and discharging cycles. When assembled as all‐solid‐state flexible symmetric supercapacitors, they offer one of the highest full‐cell capacitances (191 mF cm^?2) among similar manganese oxide/graphene foams, and retain 80% capacitance after 1000 mechanical cycles. The potential of such flexible supercapacitors is also manifested by directly powering electric nanomotors that can trace along letters “U” and T,” which is the first demonstration of flexible supercapacitors for wireless/portable nanomanipulation systems. This work could inspire a new paradigm in designing and creating 3D porous micro/nanosuperstructures for an array of self‐powered electronic and nanomechanical applications.     

Scalable Production of Graphene Inks via Wet‐Jet Milling Exfoliation for Screen‐Printed Micro‐Supercapacitors

The miniaturization of energy storage units is pivotal for the development of next‐generation portable electronic devices. Micro‐supercapacitors (MSCs) hold great potential to work as on‐chip micro‐power sources and energy storage units complementing batteries and energy harvester systems. Scalable production of supercapacitor materials with cost‐effective and high‐throughput processing methods is crucial for the widespread application of MSCs. Here, wet‐jet milling exfoliation of graphite is reported to scale up the production of graphene as a supercapacitor material. The formulation of aqueous/alcohol‐based graphene inks allows metal‐free, flexible MSCs to be screen‐printed. These MSCs exhibit areal capacitance (C_areal) values up to 1.324 mF cm^?2 (5.296 mF cm^?2 for a single electrode), corresponding to an outstanding volumetric capacitance (C_vol) of 0.490 F cm^?3 (1.961 F cm^?3 for a single electrode). The screen‐printed MSCs can operate up to a power density above 20 mW cm^?2 at an energy density of 0.064 µWh cm^?2. The devices exhibit excellent cycling stability over charge–discharge cycling (10 000 cycles), bending cycling (100 cycles at a bending radius of 1 cm) and folding (up to angles of 180°). Moreover, ethylene vinyl acetate‐encapsulated MSCs retain their electrochemical properties after a home‐laundry cycle, providing waterproof and washable properties for prospective application in wearable electronics.     

Wood‐Inspired Morphologically Tunable Aligned Hydrogel for High‐Performance Flexible All‐Solid‐State Supercapacitors

Oriented microstructures are widely found in various biological systems for multiple functions. Such anisotropic structures provide low tortuosity and sufficient surface area, desirable for the design of high‐performance energy storage devices. Despite significant efforts to develop supercapacitors with aligned morphology, challenges remain due to the predefined pore sizes, limited mechanical flexibility, and low mass loading. Herein, a wood‐inspired flexible all‐solid‐state hydrogel supercapacitor is demonstrated by morphologically tuning the aligned hydrogel matrix toward high electrode‐materials loading and high areal capacitance. The highly aligned matrix exhibits broad morphological tunability (47–12 µm), mechanical flexibility (0°–180° bending), and uniform polypyrrole loading up to 7 mm thick matrix. After being assembled into a solid‐state supercapacitor, the areal capacitance reaches 831 mF cm^?2 for the 12 µm matrix, which is 259% times of the 47 µm matrix and 403% times of nonaligned matrix. The supercapacitor also exhibits a high energy density of 73.8 µWh cm^?2, power density of 4960 µW cm^?2, capacitance retention of 86.5% after 1000 cycles, and bending stability of 95% after 5000 cycles. The principle to structurally design the oriented matrices for high electrode material loading opens up the possibility for advanced energy storage applications.     

Micro‐Supercapacitors Based on Interdigital Electrodes of Reduced Graphene Oxide and Carbon Nanotube Composites with Ultrahigh Power Handling Performance

A novel method for fabricating micro‐patterned interdigitated electrodes based on reduced graphene oxide (rGO) and carbon nanotube (CNT) composites for ultra‐high power handling micro‐supercapacitor application is reported. The binder‐free microelectrodes were developed by combining electrostatic spray deposition (ESD) and photolithography lift‐off methods. Without typically used thermal or chemical reduction, GO sheets are readily reduced to rGO during the ESD deposition. Electrochemical measurements show that the in‐plane interdigital design of the microelectrodes is effective in increasing accessibility of electrolyte ions in‐between stacked rGO sheets through an electro‐activation process. Addition of CNTs results in reduced restacking of rGO sheets and improved energy and power density. Cyclic voltammetry (CV) measurements show that the specific capacitance of the micro‐supercapacitor based on rGO–CNT composites is 6.1 mF cm^?2 at 0.01 V s^?1. At a very high scan rate of 50 V s^?1, a specific capacitance of 2.8 mF cm^?2 (stack capacitance of 3.1 F cm^?3) is recorded, which is an unprecedented performance for supercapacitors. The addition of CNT, electrolyte‐accessible and binder‐free microelectrodes, as well as an interdigitated in‐plane design result in a high‐frequency response of the micro‐supercapacitors with resistive‐capacitive time constants as low as 4.8 ms. These characteristics suggest that interdigitated rGO–CNT composite electrodes are promising for on‐chip energy storage application with high power demands.     

Layered Silicon‐Based Nanosheets as Electrode for 4 V High‐Performance Supercapacitor

Silicon‐based materials have shown great potential and been widely studied in various fields. Unlike its unparalleled theoretical capacity as anodes for batteries, few investigations have been reported on silicon‐based materials for applications in supercapacitors. Here, an electrode composed of layered silicon‐based nanosheets, obtained through oxidation and exfoliation, for a supercapacitor operated up to 4 V is reported. These silicon‐based nanosheets show an areal specific capacitance of 4.43 mF cm^?2 at 10 mV s^?1 while still retaining a specific capacitance of 834 µF cm^?2 even at an ultrahigh scan rate of 50 000 mV s^?1. The volumetric energy and power density of the supercapacitor are 7.65 mWh cm^?3 and 9312 mW cm^?3, respectively, and the electrode can operate for 12000 cycles in a potential window of 4 V at 2 A g^?1, while retaining 90.6% capacitance. These results indicate that the silicon‐based nanosheets can be a competitive candidate as the supercapacitor electrode material.     

A Low‐Cost,Self‐Standing NiCo2O4@CNT/CNT Multilayer Electrode for Flexible Asymmetric Solid‐State Supercapacitors

The demand for a new generation of flexible, portable, and high‐capacity power sources increases rapidly with the development of advanced wearable electronic devices. Here we report a simple process for large‐scale fabrication of self‐standing composite film electrodes composed of NiCo₂O₄@carbon nanotube (CNT) for supercapacitors. Among all composite electrodes prepared, the one fired in air displays the best electrochemical behavior, achieving a specific capacitance of 1,590 F g^?1 at 0.5 A g^?1 while maintaining excellent stability. The NiCo₂O₄@CNT/CNT film electrodes are fabricated via stacking NiCo₂O₄@CNT and CNT alternately through vacuum filtration. Lightweight, flexible, and self‐standing film electrodes (≈24.3 µm thick) exhibit high volumetric capacitance of 873 F cm^?3 (with an areal mass of 2.5 mg cm^?2) at 0.5 A g^?1. An all‐solid‐state asymmetric supercapacitor consists of a composite film electrode and a treated carbon cloth electrode has not only high energy density (≈27.6 Wh kg^?1) at 0.55 kW kg^?1 (including the weight of the two electrodes) but also excellent cycling stability (retaining ≈95% of the initial capacitance after 5000 cycles), demonstrating the potential for practical application in wearable devices.     

Interfacial Approach toward Benzene‐Bridged Polypyrrole Film–Based Micro‐Supercapacitors with Ultrahigh Volumetric Power Density

2D soft nanomaterials are an emerging research field due to their versatile chemical structures, easily tunable properties, and broad application potential. In this study, a benzene‐bridged polypyrrole film with a large area, up to a few square centimeters, is synthesized through an interfacial polymerization approach. As‐prepared semiconductive films exhibit a bandgap of ≈2 eV and a carrier mobility of ≈1.5 cm² V^?1 s^?1, inferred from time‐resolved terahertz spectroscopy. The samples are employed to fabricate in‐plane micro‐supercapacitors (MSCs) by laser scribing and exhibit an ultrahigh areal capacitance of 0.95 mF cm^?2, using 1‐ethyl‐3‐methylimidazolium tetrafluoroborate ([EMIM][BF₄]) as an electrolyte. Importantly, the maximum energy and power densities of the developed MSCs reach values up to 50.7 mWh cm^?3 and 9.6 kW cm^?3, respectively; the performance surpassing most of the 2D material‐based MSCs is reported to date.     

Flexible and Wire‐Shaped Micro‐Supercapacitor Based on Ni(OH)2‐Nanowire and Ordered Mesoporous Carbon Electrodes

Portable and multifunctional electronic devices are developing in the trend of being small, flexible, roll‐up, and even wearable, which asks us to develop flexible and micro‐sized energy conversion/storage devices. Here, the high performance of a flexible, wire‐shaped, and solid‐state micro‐supercapacitor, which is prepared by twisting a Ni(OH)2‐nanowire fiber‐electrode and an ordered mesoporous carbon fiber‐electrode together with a polymer electrolyte, is demonstrated. This micro‐supercapacitor displays a high specific capacitance of 6.67 mF cm^–1 (or 35.67 mF cm^–2) and a high specific energy density of 0.01 mWh cm^–2 (or 2.16 mWh cm^–3), which are about 10–100 times higher than previous reports. Furthermore, its capacitance retention is 70% over 10 000 cycles, indicating perfect cyclic ability. Two wire‐shaped micro‐supercapacitors (0.6 mm in diameter, ≈3 cm in length) in series can successfully operate a red light‐emitting‐diode, indicating promising practical application. Furthermore, synchrotron radiation X‐ray computed microtomo­graphy technology is employed to investigate inner structure of the micro‐device, confirming its solid‐state characteristic. This micro‐supercapacitor may bring new design opportunities of device configuration for energy‐storage devices in the future wearable electronic area.     

Development of Graphene Oxide/Polyaniline Inks for High Performance Flexible Microsupercapacitors via Extrusion Printing

Extrusion printing of interdigitated electrodes for flexible microsupercapacitors (fMSCs) offers an attractive route to the fabrication of flexible devices where cost, scalability, and processability of ink formulations are critical. In this work, highly concentrated, viscous, and water‐dispersible inks are developed based on graphene oxide (GO)/polyaniline (PANi) composite for extrusion printing. The optimized GO/PANi‐based all‐solid‐state symmetric fMSCs obtained by extrusion printing interdigitated microelectrodes can deliver outstanding areal capacitance of 153.6 mF cm^?2 and volumetric capacitance of 19.2 F cm^?3 at 5 mV s^?1. It is shown that by fabricating asymmetric fMSCs using the GO/PANi as positive electrode and a graphene‐based negative electrode, the voltage window can be widened from 0.8 to 1.2 V and improvements can be achieved in energy density (from 3.36 to 4.83 mWh cm^?3), power density (from 9.82 to 25.3 W cm^?3), and cycling stability (from 75% to 100% capacitance retention over 5000 cycles) compared with the symmetric counterpart. The simple ink preparation and facile device fabrication protocols reported here make the scalable fabrication of extrusion printed fMSCs a promising technology.     

A Self‐Branched Lamination of Hierarchical Patronite Nanoarchitectures on Carbon Fiber Cloth as Novel Electrode for Ionic Liquid Electrolyte‐Based High Energy Density Supercapacitors

The developments of rationally designed binder‐free metal chalcogenides decorated flexible electrodes are of paramount importance for advanced energy storage devices. Herein, binder‐free patronite (VS₄) flower‐like nanostructures are facilely fabricated on a carbon cloth (CC) using a facile hydrothermal method for high‐performance supercapacitors. The growth density and morphology of VS₄ nanostructures on CC are also controlled by varying the concentrations of vanadium and sulfur sources along with the complexing agent in the growth solution. The optimal electrode with an appropriate growth concentration (VS₄‐CC@VS‐3) demonstrates a considerable pseudocapacitance performance in the ionic liquid (IL) electrolyte (1‐ethyl‐3‐methylimidazolium trifluoromethanesulfonate), with a high operating potential of 2 V. Utilizing VS₄‐CC@VS‐3 as both positive and negative electrodes, the IL‐based symmetric supercapacitor is assembled, which demonstrates a high areal capacitance of 536 mF cm^?2 (206 F g^?1) and excellent cycling durability (93%) with superior energy and power densities of 74.4 µWh cm^?2 (28.6 Wh kg^?1) and 10154 µW cm^?2 (9340 W kg^?1), respectively. As for the high energy storage performance, the device stably energizes various portable electronic applications for a long time, which make the fabricated composite material open up news for the fabrication of fabrics supported binder‐free chalcogenides for high‐performance energy storage devices.     

Substrate‐Free and Shapeless Planar Micro‐Supercapacitors

Micro‐supercapacitors (MSCs), albeit powerful, are unable to broaden their potential applications primarily because they are not as flexible and morphable as electronics. To address this problem, a universal strategy to fabricate substrate‐free, ultrathin, shapeless planar‐MSCs with high‐performance tenability under serious deformation is put forward. These represent a new class of “all‐inside‐one” film supercapacitors, achieved by encapsulating two‐dimensional interdigital microelectrodes within chemically cross‐linked polyvinyl‐alcohol‐based hydrogel electrolyte containing graphene oxide (GO). GO nanosheets significantly improve ionic conductivity, enhance the capacitance, and boost robustness of hydrogel electrolyte. Consequently, the entire MSC, while being only 37 µm thick, can be crumpled and its shape can self‐adjust through fluid channel ten times smaller than its original size without any damage, demonstrating shapelessness. Using MXene as active material, high single‐cell areal capacitance of 40.8 mF cm^?2 is achieved from microelectrodes as thin as 5 µm. Furthermore, to demonstrate wide applicability of this protocol, screen‐printed graphene‐based highly integrated MSCs connecting nine cells in series are fabricated to stably output a high voltage of 7.2 V while crumpling them from 0.11 to 0.01 cm^?3, manifesting superior performance uniformity. This protocol allows the coexistence of high performance with incredible flexibility that may greatly diversify MSCs' applications.     

Hierarchical Ni–Co Hydroxide Petals on Mechanically Robust Graphene Petal Foam for High‐Energy Asymmetric Supercapacitors

A hierarchical structure consisting of Ni–Co hydroxide nanopetals (NCHPs) grown on a thin free‐standing graphene petal foam (GPF) has been designed and fabricated by a two‐step process for pseudocapacitive electrode applications. The mechanical behavior of GPFs has been, for the first time to our knowledge, quantitatively measured from in situ scanning electron microscope characterization of the petal foams during in‐plane compression and bending processes. The Young's modulus of a typical GPF is 3.42 GPa, indicating its outstanding mechanical robustness as a nanotemplate. The GPF/NCHP electrodes exhibit volumetric capacitances as high as 765 F cm^?3, equivalent to an areal capacitance of 15.3 F cm^?2 and high rate capability. To assess practical functionality, two‐terminal asymmetric solid‐state supercapacitors with 3D GPF/NCHPs as positive electrodes are fabricated and shown to exhibit outstanding energy and power densities, with maximum average energy density of ≈10 mWh cm^?3 and maximum power density of ≈3 W cm^?3, high rate capability (a capacitance retention of ≈60% at 100 mA cm^?2), and excellent long‐term cyclic stability (full capacitance retention over 15 000 cycles).     

Flexible Cellulose Paper‐based Asymmetrical Thin Film Supercapacitors with High‐Performance for Electrochemical Energy Storage

Cellulose paper (CP)‐based asymmetrical thin film supercapacitors (ATFSCs) have been considered to be a novel platform for inexpensive and portable devices as the CP is low‐cost, lightweight, and can be rolled or folded into 3D configurations. However, the low energy density and poor cycle stability are serious bottlenecks for the development of CP‐based ATFSCs. Here, sandwich‐structured graphite/Ni/Co₂NiO₄‐CP is developed as positive electrode and the graphite/Ni/AC‐CP as negative electrode for flexible and high‐performance ATFSCs. The fabricated graphite/Ni/Co₂NiO₄‐CP positive electrode shows a superior areal capacitance (734 mF/cm² at 5 mV/s) and excellent cycling performance with ≈97.6% C_sp retention after 15 000 cycles. The fabricated graphite/Ni/AC‐CP negative electrode also exhibits large areal capacitance (180 mF/cm² at 5 mV/s) and excellent cycling performance with ≈98% C_sp retention after 15 000 cycles. The assembled ATFSCs based on the sandwich‐structured graphite/Ni/Co₂NiO₄‐CP as positive electrode and graphite/Ni/AC‐CP as negative electrode exhibit large volumetric C_sp (7.6 F/cm³ at 5 mV/s), high volumetric energy density (2.48 mWh/cm³, 80 Wh/kg), high volumetric power density (0.79 W/cm³, 25.6 kW/kg) and excellent cycle stability (less 4% C_sp loss after 20 000 cycles). This study shows an important breakthrough in the design and fabrication of high‐performance and flexible CP‐based electrodes and ATFSCs.     

A High Energy Density Asymmetric Supercapacitor from Nano‐architectured Ni(OH)2/Carbon Nanotube Electrodes

The demand for advanced energy storage devices such as supercapacitors and lithium‐ion batteries has been increasing to meet the application requirements of hybrid vehicles and renewable energy systems. A major limitation of state‐of‐art supercapacitors lies in their relatively low energy density compared with lithium batteries although they have superior power density and cycle life. Here, we report an additive‐free, nano‐architectured nickel hydroxide/carbon nanotube (Ni(OH)₂/CNT) electrode for high energy density supercapacitors prepared by a facile two‐step fabrication method. This Ni(OH)₂/CNT electrode consists of a thick layer of conformable Ni(OH)₂ nano‐flakes on CNT bundles directly grown on Ni foams (NFs) with a very high areal mass loading of 4.85 mg cm^?2 for Ni(OH)₂. Our Ni(OH)₂/CNT/NF electrode demonstrates the highest specific capacitance of 3300 F g^?1 and highest areal capacitance of 16 F cm^?2, to the best of our knowledge. An asymmetric supercapacitor using the Ni(OH)₂/CNT/NF electrode as the anode assembled with an activated carbon (AC) cathode can achieve a high cell voltage of 1.8 V and an energy density up to 50.6 Wh/kg, over 10 times higher than that of traditional electrochemical double‐layer capacitors (EDLCs).     

3D Micro‐Extrusion of Graphene‐based Active Electrodes: Towards High‐Rate AC Line Filtering Performance Electrochemical Capacitors

A facile one‐step printing process by 3D micro‐extrusion affording binder‐free thermally reduced graphene oxide (TRGO) based electrochemical capacitors (ECs) that display high‐rate performance is presented. Key intermediates are binder‐free TRGO dispersion printing inks with concentrations up to 15 g L^?1. This versatile printing technique enables easy fabrication of EC electrodes, useful in both aqueous and non‐aqueous electrolyte systems. The as‐prepared TRGO material with high specific surface area (SSA) of 593 m² g^?1 and good electrical conductivity of ≈16 S cm^?1 exhibits impressive charge storage performances. At 100 and 120 Hz, ECs fabricated with TRGO show time constants of 2.5 ms and 2.3 ms respectively. Very high capacitance values are derived at both frequencies ranging from 3.55 mF cm^?2 to 1.76 mF cm^?2. Additionally, these TRGO electrodes can be charged and discharged at very high voltage scan rates up to 15 V s^?1 yielding 4 F cm^?3 with 50% capacitance retention. Electrochemical performance of TRGO electrodes in electrolyte containing tetraethyl ammonium tetrafluoroborate and acetonitrile (TEABF4‐ACN) yields high energy density of 4.43 mWh cm^?3 and power density up to 42.74 kW cm^?3, which is very promising for AC line filtering application and could potentially substitute state of the art electrolytic capacitor technology.     

Ultrahigh‐Strength Ultrahigh Molecular Weight Polyethylene (UHMWPE)‐Based Fiber Electrode for High Performance Flexible Supercapacitors

Flexible fiber‐based supercapacitor (FSC) with excellent electrochemical performance and high tensile strength and modulus is strongly desired for some special circumstances, such as load‐bearing, abrasion resistant, and anticutting fabrics. Here, a series of ultrahigh‐strength fiber electrodes are prepared for flexible FSCs based on ultrahigh molecular weight polyethylene fibers, on which the polydopamine, Ag, and poly (3,4‐ethylene dioxythiophene): poly(styrenesulfonate) are deposited in sequence. The modified fiber‐based electrode exhibits superhigh strength up to 3.72 GPa, which is the highest among fiber‐based electrodes reported to date. In addition, FSCs fabricated with the optimized fiber electrode shows a specific areal capacity as high as 563 mF cm^?2 at 0.17 mA cm^?2, which corresponds to a high areal energy density of ≈50.1 µWh cm^?2 at a power density of ≈124 µW cm^?2. The specific areal capacity only decrease 8% after 1000 times bending test, indicating the outstanding bending performance of this composite fiber electrode. Furthermore, several FSCs can be connected in series or in parallel to get higher working voltage or higher capacity respectively, which demonstrates its potential for broad applications in flexible devices.     

High‐Performance Wearable Micro‐Supercapacitors Based on Microfluidic‐Directed Nitrogen‐Doped Graphene Fiber Electrodes

Fiber‐shaped micro‐supercapacitors (micro‐SCs) have attracted enormous interest in wearable electronics due to high flexibility and weavability. However, they usually present a low energy density because of inhomogeneity and less pores. Here, we demonstrate a microfluidic‐directed strategy to synthesize homogeneous nitrogen‐doped porous graphene fibers. The porous fibers‐based micro‐SCs utilize solid‐state phosphoric acid/polyvinyl alcohol (H₃PO₄/PVA) and 1‐ethyl‐3‐methylimidazolium tetrafluoroborate/poly(vinylidenefluoride‐co‐hexafluoropropylene) (EMIBF₄/PVDF‐HFP) electrolytes, which show significant improvements in electrochemical performances. Ultralarge capacitance (1132 mF cm^?2), high cycling‐stability, and long‐term bending‐durability are achieved based on H₃PO₄/PVA. Additionally, high energy densities of 95.7–46.9 µWh cm^?2 at power densities of 1.5–15 W cm^?2 are obtained in EMIBF₄/PVDF‐HFP. The key to higher performances stems from microfluidic‐controlled fibers with a uniformly porous network, large specific surface area (388.6 m² g^?1), optimal pyridinic nitrogen (2.44%), and high electric conductivity (30785 S m^?1) for faster ion diffusion and flooding accommodation. By taking advantage of these remarkable merits, this study integrates micro‐SCs into flexible and fabric substrates to power audio–visual electronics. The main aim is to clarify the important role of microfluidic techniques toward the architecture of electrodes and promote development of wearable electronics.     

Oxygen‐Deficient Bismuth Oxide/Graphene of Ultrahigh Capacitance as Advanced Flexible Anode for Asymmetric Supercapacitors

Oxygen‐deficient bismuth oxide (r‐Bi₂O₃)/graphene (GN) is designed, fabricated, and demonstrated via a facile solvothermal and subsequent solution reduction method. The ultrafine network bacterial cellulose (BC) as substrate for r‐Bi₂O₃/GN exhibits high flexibility, remarkable tensile strength (55.1 MPa), and large mass loading of 9.8 mg cm^?2. The flexible r‐Bi₂O₃/GN/BC anode delivers appreciable areal capacitance (6675 mF cm^?2 at 1 mA cm^?2) coupled with good rate capability (3750 mF cm^?2 at 50 mA cm^?2). In addition, oxygen vacancies have great influence on the capacitive performance of Bi₂O₃, delivering significantly improved capacitive values than the untreated Bi₂O₃ flexible electrode, and ultrahigh gravimetric capacitance of 1137 F g^?1 (based on the mass of r‐Bi₂O₃) can be obtained, achieving 83% of the theoretical value (1370 F g^?1). Flexible asymmetric supercapacitor is fabricated with r‐Bi₂O₃/GN/BC and Co₃O₄/GN/BC paper as the negative and positive electrodes, respectively. The operation voltage is expanded to 1.6 V, revealing a maximum areal energy density of 0.449 mWh cm^?2 (7.74 mWh cm^?3) and an areal power density of 40 mW cm^?2 (690 mW cm^?3). Therefore, this flexible anode with excellent electrochemical performance and high mechanical properties shows great potential in the field of flexible energy storage devices.     

3D Structural Strengthening Urchin‐Like Cu(OH)2‐Based Symmetric Supercapacitors with Adjustable Capacitance

Developing advanced three‐dimensional (3D) structural supercapacitors with both high capacity and good mechanical strength remains challenging. Herein, a novel road is reported for fabricating 3D structural strengthening supercapacitors with adjustable capacitance based on urchin‐like Cu(OH)₂ lattice electrodes by bridging 3D printing technology with a facile electroless plating and electro‐oxidation method. As revealed by the results, the 3D‐printed octet‐truss lattice electrode features a high volumetric capacitance of 8.46 F cm^?3 at 5 mA cm^?3 and superior retention capacity of 68% at 1 A cm^?3. The assembled symmetric supercapacitor with a 70.2% capacitance retention after 5000 cycles possesses a 12.8 Wh kg^?1 energy density at a power density of 2110.2 W kg^?1. Additionally, the resulting 3D structural strengthening electrodes can achieve both high compressive strength and toughness of 30 MPa and 264.7 kJ m^?3, respectively, demonstrating high mechanical strength and excellent antideformation capacity. With the proposed strategy, the electrochemical and mechanical properties of these novel 3D structural strengthened supercapacitors can be easily tuned by a simple spatial framework design, fulfilling the increasing demand of highly customized power sources in the space‐constrained microelectronics and astronautic electronics industries.     

Engineering 3D Ion Transport Channels for Flexible MXene Films with Superior Capacitive Performance

2D MXene materials are of considerable interest for future energy storage. A MXene film could be used as an effective flexible supercapacitor electrode due to its flexibility and, more importantly, its high specific capacitance. However, although it has excellent electronic conductivity, sluggish ionic kinetics within the MXene film becomes a fundamental limitation to the electrochemical performance. To compensate for the relative deficiency, MXene films are frequently reduced to several micrometer dimensions with low mass loading (<1 mg cm^?2), to the point of detriment of areal performance and commercial value. Herein, for the first time, the design of a 3D porous MXene/bacterial cellulose (BC) self‐supporting film is reported for ultrahigh capacitance performance (416 F g^?1, 2084 mF cm^?2) with outstanding mechanical properties and high flexibility, even when the MXene loading reaches 5 mg cm^?2. The highly interconnected MXene/BC network enables both excellent electron and ion transport channel. Additionally, a maximum energy density of 252 µWh cm^?2 is achieved in an asymmetric supercapacitor, higher than that of all ever‐reported MXene‐based supercapacitors. This work exploits a simple route for assembling 2D MXene materials into 3D porous films as state‐of‐the‐art electrodes for high performance energy storage devices.