衬底放置方式对ZnO阵列形貌的影响

ZnO纳米棒阵列通过两步化学法制备,首先通过水热法在ITO衬底上制备ZnO晶种,然后把有ZnO晶种的ITO衬底垂直放入以氯化锌和氨水为溶剂的pH值为11的溶液,在85℃恒温条件下生长2h,然后在600 ℃对其进行退火处理,就得到了在ITO衬底上生长的ZnO纳米棒阵列.利用X射线衍射(XRD)、扫描电子显微镜(SEM)、高分辨透射电子显微镜(HRTEM)、紫外可见分光光度计和光致发光谱仪(PL)对样品的晶体结构、形貌和光学性能进行了表征.结果表明制备的高密度棒状ZnO纳米阵列是垂直生长在ITO衬底上,纳米棒的直径大约为150nm,长约1μm,纤锌矿ZnO纳米棒沿着[0002]方向一致生长;ZnO纳米棒阵列在波长为300 ～400 nm处出现了很强的紫外吸收峰;ZnO纳米棒阵列的光致发光光谱在380 nm左右有一个极强的紫外发光峰.研究了衬底放置方式对ZnO晶种形貌和光学性能的影响.最后通过对棒状ZnO纳米阵列形成过程中可能涉及到的化学反应以及形成机理做了简单的分析.     

基于直流磁控溅射晶种层的ZnO纳米阵列的制备及性能研究

采用直流反应磁控溅射法制备品种层薄膜,研究O2/Ar气体分压比和退火温度对品种层结构和微观形貌的影响.通过化学水浴沉积,在预制有晶种层的薄膜上制备ZnO纳米阵列结构,研究不同前驱体浓度和预制晶种层对纳米阵列生长的影响.结果表明,当O2/Ar中O2分压减少,薄膜均匀性较差,当Ar分压增加薄膜由于扩散而趋于平整.退火温度增加,晶粒尺寸增大,内应力降低.磁控溅射法预制的晶种层上生长的纳米棒垂直于衬底生长,(002)晶面的衍射峰强最高,说明纳米棒沿c轴择优取向.生长液的浓度对纳米棒的形貌影响显著,随着生长液浓度的升高,ZnO纳米阵列直径增大,顶端趋于平整的六棱柱结构.     

铟镓共掺杂对n-ZnO纳米棒/p-GaN异质结生长行为和光电性能的影响

利用低温水热法在p-GaN薄膜上生长了铟(In)和镓(Ga)共掺杂的ZnO纳米棒。X射线衍射(XRD)、X射线光电子能谱(XPS)和X射线能量色谱仪(EDS)结果表明,In和Ga已固溶到ZnO晶格中。扫描电子显微镜(SEM)结果表明, ZnO纳米棒具有良好的c轴取向性,随着In和Ga共掺杂浓度的增加,纳米棒的直径减小,密度增加。XRD结果表明,In和Ga共掺杂引起ZnO晶格常数增大,导致(002)衍射峰向低角度方向偏移。同时,ZnO的光学性质受到In和Ga共掺杂的影响。与纯ZnO相比, 共掺杂ZnO纳米棒的紫外发射峰都出现轻微红移,这是表面共振和带隙重整效应综合作用的结果。I-V特性曲线表明,随着In和Ga共掺杂浓度的增加,n-ZnO纳米棒/p-GaN异质结具有更好的导电性。     

籽晶辅助化学水浴沉积法制备ZnO纳米棒阵列

采用籽晶辅助化学水浴沉积法,即先用磁控溅射法在硅片上制备c轴取向的ZnO薄膜,以此作为籽晶层,利用化学水浴沉积法制备ZnO纳米棒阵列.利用扫描电子显微镜(SEM)和X射线衍射(XRD),研究了ZnO薄膜籽晶层的沉积温度、水浴温度和前驱体溶液中Zn源的初始浓度等对ZnO纳米棒阵列生长的影响,由此得到了结晶性好且几乎垂直于衬底方向的ZnO纳米棒阵列的生长条件,为制备基于ZnO纳米棒阵列的器件提供了条件.     

ZnO纳米线/纳米棒混合阵列的制备及其光致发光性能研究

使用无催化剂热蒸发法,在ZnO/Si薄膜衬底上制备了ZnO纳米线/纳米棒混合阵列.其中,纳米线的直径为10～20nm,纳米棒的直径为60～160 nn,二者混合在一起垂直生长于衬底表面.从衬底的上游到下游位置,混合,阵列中纳米线的含量逐渐下降,纳米棒逐渐增多.室温光致发光测试发现尺寸较小的纳米线阵列的紫外光发光强度比大尺寸纳米棒阵列高约5倍.持续激发光照射下,纳米线阵列的发光强度逐渐上升,停止光照后又逐渐下降到初始值,这可以用纳米线表面O2分子的解吸附和吸附过程来理解.     

枝状ZnO-TiO2复合纳米棒阵列的制备及表征

采用化学水浴沉积法,在预制晶种层的基底上得到垂直底面生长的有序ZnO纳米棒阵列,再用反应磁控溅射方法,沉积制备ZnO-TiO2复合结构的纳米棒阵列.利用X射线衍射(XRD)和扫描电子显微镜(SEM)对制备得到的样品进行结构和形貌表征,研究了晶种层、水浴生长液浓度和磁控溅射氧氩比对复合纳米阵列的影响.制备得到了具有TiO2分枝的复合纳米棒阵列,并初步探讨了TiO2分枝的形成机理,为制备基于复合纳米棒阵列的器件提供了条件.     

Al2O3衬底上生长ZnO薄膜的结构和光学特性

用脉冲激光沉积法在Al2O3(0001)衬底上沉积了ZnO薄膜.衬底温度分别为300℃、400℃、500℃、600℃和700℃.利用X射线衍射(XRD)和光致发光谱(PL)对薄膜的结构和光学性能进行研究.X射线衍射的结果表明在不同温度下生长的ZnO薄膜均具有高度c轴择优取向,衬底温度400℃时,膜的应力较小质量较高.ZnO薄膜有很强的紫外发光峰,紫外发光峰的强度与衬底温度密切相关,并发现当衬底温度从300℃增到400℃时,紫外发射峰出现6nm的蓝移.     

衬底对宽带隙CGS薄膜的影响

分别在Al∶ ZnO(ZAO)薄膜和Mo薄膜两种不同衬底材料上,采用“三步法”共蒸发工艺沉积了约0.8 μm厚的CuGaSe2(CGS)薄膜,用X射线衍射仪测量薄膜的织构,研究不同衬底材料对CGS薄膜的影响.在ZAO薄膜底电极上沉积的CGS薄膜的(112)衍射峰强度较Mo薄膜底电极上减弱,(220/204)衍射峰反而增强.     

ZnO纳米针阵列合成及台阶动力学生长机理研究

采用化学气相沉积系统,不用催化剂,生长过程中采用变温技术,在Si基片上合成了ZnO纳米针阵列.扫描电子显微图(SEM)显示ZnO纳米针阵列整齐密集生长在基片上,其棒状部分粗细均匀,直径约100 nm.透射电子显微照片(TEM)显示ZnO纳米针尖端呈现一系列的台阶.X射线衍射(XRD)图谱上只存在ZnO的(002)衍射峰,说明ZnO纳米针沿c轴择优取向.运用台阶动力学和奇异面生长理论分析表明ZnO纳米棒是典型的奇异面上单二维成核法向层生长机制.当单圈圆台阶扫过整个晶面的时间ts大于奇异面法向生长一个台阶高度所用时间tn时,在纳米棒顶端形成针尖;当单圈圆台阶扫过整个晶面的时间ts小于或等于奇异面法向生长一个台阶高度所用时间tn时,在纳米棒顶端不能形成针尖.     

载气流量对氧化锌纳米棒阵列的影响

本文研究了在金属有机化学气相沉积法(MOCVD)生长过程中,锌(Zn)源和氧(O)源载气流量的改变对ZnO纳米棒阵列的影响.通过改变源材料载气的流量,得到了直径从150 nm到20 nm范围、均一性明显改善的ZnO纳米棒.采用扫描电子显微镜(SEM),X射线衍射图谱(XRD),拉曼光谱(Raman)和光致荧光光谱(PL)等测试手段对样品的形貌结构和光学特性进行了表征.SEM和XRD结果表明当Zn源和O源的载气流量均为1 SLM时,所得的纳米棒直径最均匀,排列整齐,垂直于衬底生长,且结晶度最好.PL谱显示纳米棒的紫外带边峰发生了蓝移,可能与表面效应的增加有关.     

A review of measurement of thermophysical properties of silicon melt

Measurements of thermophysical properties of Si melt and supplementary study of X-ray scattering/diffraction by the authors' group were reviewed. The values obtained differed variously from those of literature. Density was 2–3% larger, surface tension 20–30% smaller, viscosity up to 40% larger, electrical conductivity 8% smaller, spectral emissivity more or less in good agreement with literature values, and thermal diffusivity a few percent larger. An anomalous density jump was found near the melting point. Surface tension and viscosity also showed anomaly. A strange time-dependent change of density was observed over 3 h after melting. X-ray analyses suggested a slight change in local atom ordering, but showed no sign of cluster formation. An addition of 0.1 at% gallium caused the density jump to disappear, while that of boron caused no change. An EXAFS study of the former melt indicated a strong interaction between Ga and Si atoms as if molecules of GaSi₃ existed. The implications of the measured properties are a possibility of soft-turbulence in an Si melt in a relatively large crucible, a more complicated manner of intake of oxygen depleted molten Si from the free surface region to underneath the growing crystal, and a relaxation of the melt after melting arising from trapped gas species.     

原位氮化法制备TiN纳米粉体

用溶胶凝胶法合成的纳米TiO2粉体作为原料,将该粉体在氨气中进行原位氮化制备了TiN纳米粉体.用XRD,TEM,化学分析等手段对合成的TiN纳米粉体的物相组成、形貌、成分进行了分析.实验分析表明:在1000℃和1100℃下分别氮化5h,可以制备粒径大约为40nm和80nm的TiN粉体,其TiN的含量分别为95.40;和98.37;;而在1000℃条件下氮化时间减少到2h时,TiN的含量仅为58.36;.氮化温度和氮化时间是合成纳米TiN的重要因素,提高合成温度和延长氮化时间均可形成纯度较高的TiN纳米粉体,但延长氮化时间更有利于获得粒径小的氮化钛粉体.     

Mesomorphism Dependence on the Position of Substitution of a Pair of Esters

A novel homologous series of ethylene derivatives of thermotropic liquid crystals has been synthesized. The methoxy to octyloxy derivatives are nematogenic, the decyloxy to tetradecyloxy derivatives are smectogenic, in addition to nematogenic, and the hexadecyloxy homologue is smectogenic only. All the members of the series are enantiotropically mesogenic. Thermotropic behavior was determined by an optical polarizing microscope equipped with a heating stage and Differential Scanning Calorimetry (DSC) study. Analytical and spectral data confirm the molecular structures of homologues (infrared, nuclear magnetic resonance, mass spectra, X-ray, and DSC data). Textures of the nematic phase are threaded or Schlieren and that of smectic phase are focal conic fan-shaped of smectic A or C. Transition curves of the phase diagram behave in a normal manner except one or two deviations from the normal trend. The mesophase range (Sm+N) varies from 3°C to 44°C. The average thermal stability for smectic is 93°C and that for nematic 117.4°C. The LC behavior of the novel series is compared with a structurally similar known series.     

On the influence of structural features of DNA on the possibility of metabolic transfer of electrons

Abstract

A fragment of a DNA molecule is considered as one of the channels of metabolic electron transfer. The heterogeneity of the complementary chains is effectively taken into account. This made it possible to find the speed of the electron injected into the DNA conduction band and the current density that it creates. Estimates of electron mobility in nucleic acid chains are made. They were an order of magnitude smaller than that of typical semiconductors. For the specific conductivity of nucleic acid chains, estimates provide a conductivity of one to two orders of magnitude lower than in graphite.     

Effect of alumina on enthalpy of mixing of mixed alkali silicate glasses

The enthalpy of mixing of mixed alkali (Na₂O and K₂O) silicate glasses containing various concentrations of alumina was determined using an ion-exchange equilibrium method. For glasses with a constant alkali concentration, the enthalpy of mixing was found to become less negative with alumina addition. Consistent with our previous results on the enthalpy of mixing of alumina-free mixed alkali silicate glasses, the magnitude of enthalpy of mixing exhibited a good correlation with the molar volume mismatch of the corresponding two single alkali glasses as well as with the extent of conductivity mixed alkali effect, e.g. excess activation energy of conductivity, ΔE. The reduction of the magnitude of the enthalpy of mixing with alumina addition can be attributed to the reduction of non-bridging oxygen and ionic field strength. Combining the present results with results obtained earlier, the magnitude of the enthalpy of mixing for all mixed alkali (Na₂O and K₂O) silicate glasses with and without alumina was expressed by a simple function of a modified Tobolsky parameter, which takes into account the alkali concentration and the difference in cation-to-effective anion distances. The enthalpy of mixing data of the mixed alkali glasses was then compared with reported experimental data on the conductivity of mixed alkali aluminosilicate glasses. What appears to be conflicting experimental data can be understood in terms of the magnitude of the enthalpy of mixing and we can conclude that the mixed alkali effect is closely correlated with the negative enthalpy of mixing.     

电子显微分析在表征纳米晶体化学组分中的应用

纳米材料的化学组分及含量影响其光、电、声、热、磁等物理性能,电子显微分析是表征纳米晶体化学组分的重要方法之一.本文综述了X-射线能谱(EDS)、X-射线波谱(WDS)、电子能量损失谱(EELS)和选区电子衍射(SAED)等现代电子显微分析技术在表征纳米晶体化学组分、形貌、尺寸和结构等方面的应用及其研究进展,并比较了这些分析方法存在的差异,提出了其应用中存在的不足及今后的研发方向.     

Ni-ZrO2纳米复合电铸层的制备及纳米颗粒分布均匀性研究

研究了在复合电铸过程中,当其它工艺参数一定时,复合电铸层的沉积速率及其厚度随时间的变化趋势, 以及复合电铸层表面微观形貌随电沉积时间的变化趋势.测定了复合电铸层的组织成分,并就纳米颗粒在复合电铸层表面和横截面上分布的均匀性进行了评价.结果表明,复合电铸层表面平整,组织均匀致密,其组成主要是镍和所复合的纳米颗粒,纳米颗粒较为均匀地分散在复合电铸层中.     

Evolution of the Defect Structure of Zinc-Oxide as a Consequence of Tribophysical Activation

Zinc-oxide powder was tribophysically activated in a high-energy vibro mill in a continual regime in air for 3, 30 and 300 minutes with the purpose of modifying the powders physico-chemical properties. By analyzing of data obtained by X-ray powder diffraction, electron diffraction and transmission electron microscopy, the values of distances between corresponding crystallographic planes, average domain sizes of coherent scattering, i.e. crystallites, width of diffraction lines due to the existence of microstrains, and microstrain values, minimal dislocation densities, dislocation density due to microstrain and real dislocation density, and also average distances between dislocations were determined. The dependence of these values on the activation time was established, which enabled analysis of the evolution of the defect structure of zinc-oxide powders during tribophysical activation by grinding in the described regime.     

立方晶系晶体本征铁弹相变序参量的选取

在本征铁弹相变的软模理论的基础上,依据弹性本构关系和居里原理,给出了立方晶系晶体所有可能的自发应变的种类,研究了立方晶系晶体本征铁弹相变序参量的选取问题.以Th群和Oh群为例,阐明了不同类的序参量导致晶体对称性变化相同的的原因,提出了该情况下序参量选取的“就少不就多”的原则.得到了发生本征铁弹相变时所有可能的序参量及晶体的对称性的变化.     

PEG聚合度对氧化铝造粒粉的性能影响

为制备适用于干压成型的氧化铝造粒粉,研究了PEG聚合度对氧化铝造粒粉微观形貌、流动性和松装密度的影响.结果表明PEG的聚合度对氧化铝浆料粘度影响显著,PEG2000-6000是较为理想的粘结剂选择,造粒粉的流动性与环境温度及湿度相关.采用正交实验设计,以造粒粉的流动性和松装密度为评价指标,对PEG聚合度、粘结剂添加量和固含量进行了优选,其影响顺序为PEG聚合度＞固含量＞粘结剂添加量.以优选参数PEG6000、添加量为4wt;、固含量为80wt;,制备了性能优良的氧化铝喷雾造粒粉.