Gelation-free synthesis of poly(allyl methacrylate-co-butyl acrylate) copolymers by atom transfer radical polymerization

The preparation of functional copolymers based on allyl methacrylate (AMA) and butyl acrylate (BA) without gel formation via atom transfer radical polymerization is described. The gelation-free controlled radical copolymerizations were carried out in benzonitrile solution at 70 °C using ethyl 2-bromoisobutyrate as initiator and mixed halogen technique, copper chloride along with N,N,N′,N″,N″-pentamethyldiethylenetriamine as the catalyst system. Kinetic analyses have demonstrated that all the copolymerizations showed a general behaviour characterized by two clearly differentiated stages. Thus, in an initial stage, the polymerizations presented first order kinetic with respect to the monomer concentration. In the subsequent stage, at low-intermediate conversions, a deceleration in the rate copolymerization leads to limit conversions, which decrease as the initial concentration of BA in the feed increases. The reactivity ratios values were calculated from the copolymer composition determined by ¹H NMR, and using the extended Kelen–Tüdös method. Values of 2.70 ± 0.21 and 0.49 ± 0.04 were obtained for AMA and BA, respectively. The cumulative copolymer compositions as a function of conversion degree for the different monomer molar fractions in the feed showed gradient character of the copolymers obtained.     

Vapor-phase selective hydrogenation of maleic anhydride to succinic anhydride over Ni/TiO2 catalysts

A series of supported Ni/TiO₂ catalysts were prepared by incipient wetness impregnation method under different calcination temperatures, and the as-prepared catalysts were characterized by X-ray diffraction (XRD), hydrogen temperature-programmed reduction (H₂-TPR) and X-ray photoelectron spectroscopy (XPS). The catalytic properties of these Ni/TiO₂ catalysts were investigated in the vapor phase hydrogenation of maleic anhydride (MA) to succinic anhydride (SA). The results showed that the catalytic activity and the selectivity of the Ni/TiO₂ catalysts were strongly affected by the calcination temperature. The catalyst calcined at 1023 K showed a relatively higher SA selectivity of 96% at high MA conversion (96%) under the tested conditions (493 K and 0.2 MPa). The improvement of SA selectivity could be mainly assigned to the presence of suitable metal–support interaction, which can play a role in catalytic property of active nickel species as electron promoter. Besides, the change of surface properties of TiO₂ support with the increasing calcination temperatures, e.g., the decrease of Lewis acid sites, might also have some positive role in reducing the side-products like γ-butyrolacetone (GBL).     

Effect of the maleic anhydride content on the structural,thermal, rheological and film properties of the n-butyl methacrylate–maleic anhydride copolymers

Various copolymers of n-butyl methacrylate (nBMA)-maleic anhydride (MA) were synthesized by free radical solution polymerization using xylene as a solvent, with monomer ratio of (nBMA/MA) 80/20, 65/35 and 50/50 wt%. The nBMA/MA copolymers were analyzed by Fourier transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance (¹H NMR), gel permeation chromatography (GPC) differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), rheology, acid value, microhardness and friction resistance. The formation of the nBMA/MA copolymers was proven by FTIR and ¹H NMR. The conversion percentage, glass transition temperature (T_g), thermal stability, hardness and the friction resistance of the nBMA/MA copolymers increased with the MA contents in the copolymers. All copolymers presented a thinning-shear rheological behavior due to the presence of entanglements. All films of the copolymers showed a good chemical resistance to HCl and NaCl solutions, but in the presence of NaOH solutions the films exhibited a blister.     

Helical poly(N-propargylamide)s with functional catechol groups: Synthesis and adsorption of metal ions in aqueous solution

A novel type of helical N-propargylamide (PA) copolymer was synthesized by catalytic polymerization of monomer 1 (M1), which provided pendent functional catechol groups, and monomer 2 (M2), which endowed the expected copolymer backbones with helical structures. With [(nbd)Rh⁺B^?(C₆H₅)₄ (nbd = 2,5-norbornadiene)] as catalyst, PA copolymers could be obtained with moderate molecular weights (3800–14,000) in high yields (?96%). The functional catechol groups enhanced the hydrophilicity of the hydrophobic mono-substituted polyacetylenes and aided the helical PA copolymers in showing a considerable adsorbance toward metal ions [Fe(III), Cr(III), Ni(II), Zn(II), Cu(II) and Cu(I)] in aqueous solution. The prepared copolymer in which M1/M2 was 0.1/0.9 [mol/mol, poly(1_0.1-co-2_0.9)] showed the highest adsorption capacity among the examined helical copolymers. In particular, for Fe(III), the maximum adsorption capacity was 186 mg g^?1.     

Reactive and stimuli-responsive maleic anhydride containing macromers – multi-functional cross-linkers and building blocks for hydrogel fabrication

Macromers with functional groups that allow for chemical derivatization, polymerization reactions or impart specific physico-chemical properties are functional building blocks for polymeric systems used in different biomedical applications. With this motivation, a series of oligomeric macromers was synthesized by free radical polymerization of maleic anhydride (MA) with N-isopropylacrylamide (NiPAAm) and pentaerythritol diacrylate monostearate (PEDAS). This chemical design provides anhydride groups for effective reactivity of the macromers with amines and other nucleophiles, copolymerized NiPAAm for temperature responsiveness and lipophilic stearate domains for increased hydrogel stability. Macromers were synthesized with different MA co-monomer feeds and oligomeric molecules (Mn below 5000 Da) were obtained with MA contents between 7% and 27% as determined by titration. The fraction of chemically intact anhydrides was calculated to range from 75% to 80%. The ability of the macromers to cross-link di- or oligovalent amines as a function of MA content was investigated rheologically. It was also demonstrated that monovalent amines, e.g. aminofluorescein, could be grafted to the macromer chain utilizing only a fraction of the anhydride functionalities. The derivatized macromers could still participate in cross-linking reactions due to the remaining anhydrides. Temperature sensitivity was shown for aqueous solutions of macromers with fully dissociated anhydride groups. The solutions were additionally responsive to changes in calcium ion concentration and pH. Extracts from macromer cross-linked polyether hydrogels showed no toxicity on L929 fibroblasts.The macromers have perspective as biocompatible cross-linkers for hydrogel fabrication from various biomacromolecules with the opportunity to decorate the gels with monoamine molecules that alter the biological or physico-chemical properties.     

Synthesis,characterization and thermal properties of homo and copolymers of 3,5-dimethoxyphenyl methacrylate with glycidyl methacrylate: Determination of monomer reactivity ratios

The new methacrylic monomer, 3,5-dimethoxyphenyl methacrylate (DMOPM) was synthesized by reacting 3,5-dimethoxyphenol dissolved in ethyl methyl ketone (EMK) with methacryloyl chloride in presence of triethylamine as a catalyst. The homopolymer and copolymers of DMOPM with glycidyl methacrylate (GMA) were synthesized by free radical polymerization in EMK solution at 70 ± 1 °C using benzoyl peroxide as a free radical initiator. The copolymerization behaviour was studied in a wide composition interval with the mole fractions of DMOPM ranging from 0.15 to 0.9 in the feed. The homopolymer and the copolymers were characterized by FT-IR, ¹H NMR and ¹³C NMR spectroscopic techniques. The solubility was tested in various polar and non-polar solvents. The molecular weight and polydispersity indices of the polymers were determined using gel permeation chromatography. The glass transition temperature of the copolymers increases with increase in DMOPM content. The thermogravimetric analysis of the polymers showed that the thermal stability of the copolymer increases with DMOPM content. The copolymer composition was determined using ¹H NMR spectra. The monomer reactivity ratios were determined by the application of conventional linearization methods such as Fineman–Ross (r₁ = 0.520, r₂ = 2.521), Kelen–Tudos (r₁ = 0.629, r₂ = 2.554) and extended Kelen–Tudos methods (r₁ = 0.600, r₂ = 2.502).     

Alternating copolymerization of CHO and MA catalyzed by the hetero-bimetallic Zn-Yb-Salen complex

For the hetero-bimetallic complex [Zn(L)(μ₁-OAc)Yb(μ₁-OAc)(μ₂-OAc)(H₂O)] (1; H₂L = N,N′-bis(3-methoxy-salicylidene)cyclohexane-1,2-diamine), its character of self-owned normal OAc⁻ initiators around two active species endows effective bulk solvent-free copolymerization of CHO (cyclohexene oxide) and MA (maleic anhydride) in the presence of cocatalyst (DMAP, 4-(dimethylamino)-pyridine or TPP, triphenylphosphine) or not. Especially from TPP-assisted controllable copolymerization, perfectly alternating polyesters are obtained.     

Synthesis and investigation of monomodal hydroxy-functionalized PEG methacrylate based copolymers with high polymerization degrees. Modification by “grafting from”

The synthesis of monomodal copolymers with poly(ethylene glycol) (PEG) side chains from commercial poly(ethylene glycol) methacrylates (PEGMA) by atom transfer radical polymerization (ATRP) is verified. Two hydroxy-functionalized PEGMA macromonomers (520 g/mol and 360 g/mol) were copolymerized with methyl methacrylate (MMA) using various initial feed (1.5/98.5–50/50 mol.%). The copolymers P(MMA-co-PEGMA) with high degree of polymerization, e.g. 100–275 of repeating units in the backbone including 7–56 PEG side chains, were obtained. The relative reactivity ratios of PEGMA and MMA determined by the Jaacks method indicated slightly faster incorporation of macromonomer into polymeric chain than MMA (r_MMA = 0.79; r_PEGMA = 1.27). The polymers containing at least 17 mol.% of PEGMA units were water-soluble and exhibited clouding point at temperature in a broad range of 39–70 °C. The temperature-sensitive effect makes these polymers as a potential carriers in drug delivery systems. In the case of copolymers insoluble in water, a three-step procedure, including esterification to ATRP multifunctional macroinitiators, ATRP of tert-butyl methacrylate (tBMA) by grafting from, deprotection of carboxylic groups by removing tert-butyl groups, was applied to extend PEG grafts and expand the content of hydrophilic fraction (32–94 mol.%), what efficiently developed polymer solubility in polar solvents giving possibility for the future biomedical applications.     

Gas-phase epoxidation of propylene through radicals generated by silica-supported molybdenum oxide

It was found that silica-supported molybdenum oxide was high effective for the epoxidation of propylene among various silica-supported metal oxides. The post-catalytic bed volume played an important role in its formation. On a MoO_x/SiO₂ with 0.255 mmol/g-SiO₂, a propylene conversion of 17.6% and a PO selectivity of 43.6% were obtained at 5 atm, 573 K and flow rates of C₃H₆/O₂/He = 10/5/10 cm³ min⁻¹. The characterization studies indicated that crystalline MoO₃ nano-particle species was more effective for propylene epoxidation to PO than molecularly dispersed Mo oxide species. The reaction mechanism of propylene epoxidation on MoO_x/SiO₂ catalysts is hypothesized to involve gas-phase radicals generated at relatively low temperature by the dispersed molybdenum oxide species. These radicals participated in homogeneous reactions with molecular oxygen to produce propylene oxide.     

The contribution of homogeneous and non-oxidative side reactions in the performance of vanadyl pyrophosphate,catalyst for the oxidation of n-butane to maleic anhydride,under hydrocarbon-rich conditions

The reactivity of vanadyl pyrophosphate, catalyst for the selective oxidation of n-butane to maleic anhydride, was examined under n-butane-rich conditions, simulating a feed in which oxygen is the limiting reactant, and a process in which the unconverted n-butane is recycled. A lower selectivity to maleic anhydride was found with respect to the hydrocarbon-lean conditions, due to the higher selectivity to carbon oxides and to the formation of C₈ by-products: tetrahydrophthalic and phthalic anhydrides. The latter compounds formed by a consecutive reaction of maleic anhydride with the unsaturated C₄ intermediates. This occurred under conditions of total oxygen conversion, due to the decreased catalyst oxidizing property. A relevant contribution of radicalic, homogeneous reactions was also observed, which mainly led to the formation of carbon oxides and olefins. This contribution decreased in the presence of the catalyst, which acted as a radical scavenger, but nevertheless remained important at temperatures higher than 400 °C. When conditions were used under which the conversion of oxygen was not total, olefins generated in the gas phase reacted at the catalyst surface yielding maleic anhydride. This homogeneously initiated heterogeneous process led to an unusual effect, of a relevant increase of maleic anhydride yield over 400 °C.     

Synthesis and photoresponsive behavior of the high-Tg azobenzene polymers via RAFT polymerization

Well-defined photo-responsive alternating copolymers, poly(4-(N-maleimido)azobenzene-alt-styrene)s (PMSts), were successfully synthesized via reversible addition–fragmentation chain transfer (RAFT) polymerization. A divinyl monomer was used in this polymerization to prepare high molecular weight azobenzene polymers. These polymers had good solubility in most organic solvents, formed films well, and had high glass transition temperatures (T_g = 174–250 °C) and were heat resistant (T_d > 320 °C). The photo-induced trans–cis isomerization of the copolymers was examined in chloroform solution. Surface-relief-gratings (SRGs) formed on the polymer films were also investigated using illumination from a linearly polarized Kr⁺ laser beam.     

Mineralisation of CaCO3 in the presence of polycarboxylate comb polymers

Polycarboxylate ether (PCE) copolymers based on maleic anhydride and α-allyl-ω-methoxy polyethylene glycol ethers were synthesised and their influence on the morphogenesis of CaCO₃ crystals obtained from combined aqueous solutions of CaCl₂ and Na₂CO₃ after 2 hours at pH = 7 and 12.6 was investigated. Generally, PCEs constitute highly effective crystal growth modifiers for CaCO₃ whereby nucleation rate and morphology are controlled by pH and molecular architecture (side chain length) of PCE. Complexation of Ca^2 + by carboxylate groups lined up along the PCE backbone templates formation of the first layer of CaCO₃ from which nuclei can develop. The PCE-stabilised nanocrystals then self-assemble into larger mesocrystals possessing peanut, dumbbell, spherulite or star shapes. Confocal Raman microscopy confirmed significant enrichment of PCE copolymers in the interstitial spaces between individual nanocrystals. Worm-shaped PCEs present more effective crystal modifiers than star polymers. The results suggest that PCEs may also modify the growth of cement hydrates.     

Aluminum diboride synthesis from elemental powders by mechanical alloying and annealing

In this study, AlB₂ powders were synthesized by using a combined method of mechanical alloying (MA) and annealing of elemental aluminum (Al) and boron (B) powders. Milling was performed in a planetary ball-mill (Fritsch? Pulverisette 7 Premium Line) up to 15 h under argon (Ar) atmosphere. Annealing process was carried out in a tube furnace at 650 °C for 6 h under Ar atmosphere. The effects of MA durations on the annealing process and AlB₂ formation were investigated. The conversion of Al and B powders to AlB₂ starts after only MA for 3 h or after MA for 1 h and subsequent annealing. A slight formation of AlB₁₂ occurs at 242 °C for as-blended powders and it shifts to about 272 °C for MA’d powders. Al–B powder blends MA’d for 9 h and annealed have AlB₂ particles in size between 35 and 75 nm in the presence of Al₁₃Fe₄, Fe₃B and Fe₂B contaminations.     

The effect of gamma irradiation on mechanical,thermal and morphological properties of glass fiber reinforced polyethylene waste/reclaim rubber composites

Composites of waste polyethylene (WPE), collected from municipal solid waste/recycled waste rubber powder (RWRP) reactive compatibilizing agent, maleic anhydride (MA) and glass fiber (GF) up to 20 wt%, prepared by melting and irradiated with gamma-rays up to 150 kGy have been studied. Tensile strength (T_S), elongation at break (E_b), elastic modulus, hardness, thermal and morphological parameters of the irradiated composites were investigated. The examined mechanical properties have been found to improve largely with filler content. Interesting E_b behavior has been detected for the irradiated composites loaded up to ∼10 wt% GF and has been basically discussed in view of matrix crystallinity and morphology. TGA thermograms of unirradiated composites revealed enhanced thermal stability than that reported for the blend whereas comparatively slight improvement has been demonstrated by irradiation. Whereby insignificant alteration in T_m values was observed by loading or irradiation, yet ΔH_m maximum of 3.41 J/g, indicated for the 5 wt% GF irradiated composite with an integral dose of 75 kGy, emphasizes the influence of the relatively moderate load and dose levels on matrix stability. The phenomenon has been confirmed by the respective SEM micrographs.     

Oxidation behavior of Al2O3 reinforced MoSi2 composite coatings fabricated by vacuum plasma spraying

MoSi₂, MoSi₂–10 vol.% Al₂O₃, MoSi₂–30 vol.% Al₂O₃ (denoted as MA0, MA1, MA3, respectively) coatings were fabricated by vacuum plasma spraying (VPS), and their oxidation behavior was examined at low temperature (500 °C) and high temperature (1500 °C). The test at 500 °C showed that the addition of Al₂O₃ effectively restrained the pest oxidation of MoSi₂. The MA1 coating had satisfactory fluid surface and presented good oxidation resistance at 1500 °C. However, the MA3 coating showed worse oxidation resistant behavior compared with the MA0 coating because of mullite formation.     

Copolymers of 4(5)-vinylimidazole and ethyleneglycol methacrylate phosphate: Synthesis and proton conductivity properties

A series of copolymers were produced by conventional free-radical polymerization of ethyleneglycol methacrylate phosphate (EGMAP) and 4(5)-vinylimidazole (4-VIm) at several feed compositions using DMF as solvent. The copolymers were characterized by ¹H NMR and FT-IR. Copolymer compositions were obtained by elemental analysis. Reactivity ratios of the monomers are equal to: r₁ = 0.12 ± 0.03 and r₂ = 0.19 ± 0.05 for 4-VIm–EGMAP system that exhibited an alternating behavior. Thermal properties of the dry copolymers were investigated via thermogravimetry analysis (TG) and differential scanning calorimetry (DSC). The ion exchange capacity (IEC) and anhydrous proton conductivities of the samples were measured and analyzed according to copolymer composition.     

Synthesis of amphiphilic copolymers by ATRP initiated with a bifunctional initiator containing trichloromethyl groups

Bifunctional polystyrene macroinitiators, having various molecular weights, were prepared by atom transfer radical polymerization (ATRP), initiated with bifunctional initiator 1,3-bis{1-methyl-1[(2,2,2-trichloroethoxy) carbonylamino]ethyl}benzene in conjunction with CuCl catalyst and polyamine ligands. These macroinitiators were subsequently used for ATRP of tert-butyl acrylate (t-BuA), giving BAB triblocks poly[(t-BuA)-b-(Sty)-b-(t-BuA)] as precursors of amphiphilic copolymers. Both the polymerization steps proceeded as controlled processes with linear semi-logarithmic conversion plots and lengths of the blocks following theoretical predictions. Hydrolysis of outer poly(t-BuA) blocks led to triblock copolymers with the central polystyrene block and outer blocks of poly(acrylic acid), the molecular weights of which ranged from ca. 5 × 10³ to almost 1 × 10⁵ Da.     

Synthesis and characterization of alkyd resins based on Camelina sativa oil and polyglycerol

A one pot synthesis of alkyd resins based on the Camelina sativa oil as a new renewable raw material and on polyglycerols as polyols was carried out. The oligomerization of glycerol was conducted in the presence of LiOH (0.1 wt%) at 245 °C. The total content of diglycerol reached its maximum (about 33.5 wt%) after 7 h. The oligomerization product with no additional treatment was subjected to the alcoholysis reaction with purified camelina oil. The alkyd resin was obtained after polycondensation of the alcoholysis products with phthalic and maleic anhydrides at 230–250 °C. A real possibility was determined for the synthesis of alkyd resins with some properties similar to those which can be found in equivalent products manufactured on the basis of semi drying oil and pentaerythritol like flexibility and drying time.     

Integration of tailored reduced graphene oxide nanosheets and electrospun polyamide-66 nanofabrics for a flexible supercapacitor with high-volume- and high-area-specific capacitance

Nanofiber fabric is firstly introduced to replace common microfiber fabrics as the platform for flexible supercapacitors. Nanofiber and microfiber electrodes can be simply fabricated using a dipping process that impregnates reduced graphene oxide (RGO) nanosheets into electrospun polyamide-66 (PA66) nanofiber and microfiber fabrics. RGO nanosheets are tailored to various sizes and only RGO with a medium diameter of 250–450 nm (denoted as M-RGO) can effectively penetrate the pores of nanofiber fabrics for constructing smooth conductive paths within PA66 nanofiber fabrics. The synergistic effect between suitable sizes of RGO nanosheets and nanofiber fabrics with a high specific area provides a symmetric supercapacitor composed of M-RGO/PA66 nanofiber fabric electrodes with high-volume and high-area specific capacitance (C_S,V and C_S,A, equal to 38.79 F cm⁻³ and 0.931 F cm⁻² at 0.5 A g⁻¹, respectively), which are much larger than that of a symmetric supercapacitor composed of RGO/PA66 microfiber fabric electrodes (8.52 F cm⁻³ and 0.213 F cm⁻² at 0.5 A g⁻¹). The effect of impregnating nanofiber fabrics with suitably sized RGO to promote C_S,V and C_S,A of flexible supercapacitors has been demonstrated.     

Synthesis and investigation of a photosensitive,europium-containing polymer

A series of europium complexes containing polymeric reactivity groups have been successfully synthesized using a simple method. Among them, Eu(DBM)₂(Phen)(MA), which has the best fluorescence properties and solubility, was polymerized with glycidyl methacrylate (GMA) for use as a novel UV-written polymer material. The Poly (GMA-co-Eu(DBM)₂(Phen)(MA)) containing different proportions of europium were prepared, and their spectroscopic properties were investigated in detail. Polymer films with optimum proportions (a molar ratio between GMA and Eu(DBM)₂(Phen)(MA) of 15) exhibited good UV light lithograph sensitivities, strong visible fluorescence intensities, high glass transition temperatures (T_g: >170 °C), good thermal stabilities (T_d: up to 295 °C) and solvent resistances after crosslinking. Micro patterns with smooth top surfaces were fabricated from the resulting polymer by using direct UV exposure and chemical development.