Performance and exhaust emissions of a biodiesel engine

In this study, the applicabilities of Artificial Neural Networks (ANNs) have been investigated for the performance and exhaust-emission values of a diesel engine fueled with biodiesels from different feedstocks and petroleum diesel fuels. The engine performance and emissions characteristics of two different petroleum diesel-fuels (No. 1 and No. 2), biodiesels (from soybean oil and yellow grease), and their 20% blends with No. 2 diesel fuel were used as experimental results. The fuels were tested at full load (100%) at 1400-rpm engine speed, where the engine torque was 257.6 Nm. To train the network, the average molecular weight, net heat of combustion, specific gravity, kinematic viscosity, C/H ratio and cetane number of each fuel are used as the input layer, while outputs are the brake specific fuel-consumption, exhaust temperature, and exhaust emissions. The back-propagation learning algorithm with three different variants, single layer, and logistic sigmoid transfer function were used in the network. By using weights in the network, formulations have been given for each output. The network has yielded R² values of 0.99 and the mean % errors are smaller than 4.2 for the training data, while the R² values are about 0.99 and the mean % errors are smaller than 5.5 for the test data. The performance and exhaust emissions from a diesel engine, using biodiesel blends with No. 2 diesel fuel up to 20%, have been predicted using the ANN model.     

The effects of turbocharger on the performance and exhaust emissions of a diesel engine fuelled with biodiesel

This paper investigates the effects of turbocharger on the performance of a diesel engine using diesel fuel and biodiesel in terms of brake power, torque, brake specific consumption and thermal efficiency, as well as CO and NO_x emissions. For this aim, a naturally aspirated four-stroke direct injection diesel engine was tested with diesel fuel and neat biodiesel, which is rapeseed oil methyl ester, at full load conditions at the speeds between 1200 and 2400 rpm with intervals of 200 rpm. Then, a turbocharger system was installed on the engine and the tests were repeated for both fuel cases. The evaluation of experimental data showed that the brake thermal efficiency of biodiesel was slightly higher than that of diesel fuel in both naturally aspirated and turbocharged conditions, while biodiesel yielded slightly lower brake power and torque along with higher fuel consumption values. It was also observed that emissions of CO in the operations with biodiesel were lower than those in the operations with diesel fuel, whereas NO_x emission in biodiesel operation was higher. This study reveals that the use of biodiesel improves the performance parameters and decreases CO emissions of the turbocharged engine compared to diesel fuel.     

The effects of ethanol–unleaded gasoline blends on engine performance and exhaust emissions in a spark-ignition engine

Alcohols have been used as a fuel for engines since 19th century. Among the various alcohols, ethanol is known as the most suited renewable, bio-based and ecofriendly fuel for spark-ignition (SI) engines. The most attractive properties of ethanol as an SI engine fuel are that it can be produced from renewable energy sources such as sugar, cane, cassava, many types of waste biomass materials, corn and barley. In addition, ethanol has higher evaporation heat, octane number and flammability temperature therefore it has positive influence on engine performance and reduces exhaust emissions. In this study, the effects of unleaded gasoline (E0) and unleaded gasoline–ethanol blends (E50 and E85) on engine performance and pollutant emissions were investigated experimentally in a single cylinder four-stroke spark-ignition engine at two compression ratios (10:1 and 11:1). The engine speed was changed from 1500 to 5000 rpm at wide open throttle (WOT). The results of the engine test showed that ethanol addition to unleaded gasoline increase the engine torque, power and fuel consumption and reduce carbon monoxide (CO), nitrogen oxides (NO_x) and hydrocarbon (HC) emissions. It was also found that ethanol–gasoline blends allow increasing compression ratio (CR) without knock occurrence.     

Influence of injection timing on the exhaust emissions of a dual-fuel CI engine

Environmental concerns and limited amount of petroleum fuels have caused interests in the development of alternative fuels for internal combustion (IC) engines. As an alternative, biodegradable, and renewable fuel, ethanol is receiving increasing attention. Therefore, in this study, influence of injection timing on the exhaust emission of a single cylinder, four stroke, direct injection, naturally aspirated diesel engine has been experimentally investigated using ethanol blended diesel fuel from 0% to 15% with an increment of 5%. The engine has an original injection timing 27° CA BTDC. The tests were performed at five different injection timings (21°, 24°, 27°, 30°, and 33° CA BTDC) by changing the thickness of advance shim. The experimental test results showed that NO_x and CO₂ emissions increased as CO and HC emissions decreased with increasing amount of ethanol in the fuel mixture. When compared to the results of original injection timing, at the retarded injection timings (21° and 24° CA BTDC), NO_x and CO₂ emissions increased, and unburned HC and CO emissions decreased for all test conditions. On the other hand, with the advanced injection timings (30° and 33° CA BTDC), HC and CO emissions diminished, and NO_x and CO₂ emissions boosted for all test conditions.     

Influence of water on exhaust emissions on unmodified diesel engine propelled with biodiesel

The present work aims to investigate the effect of water addition to orange peel oil biodiesel (BD100) in a diesel engine to reduce the exhaust emissions. Fuel samples are prepared with different concentrations of water into biodiesel, 95% biodiesel + 5% water (BD95W5) and 90% orange peel oil biodiesel + 10% water (BD90W10). The water is added to biodiesel in presence of surfactant (Span-80). The experimental investigation on diesel engine reveals that the oxides of nitrogen emission and smoke emission are reduced for BD95W5 and BD90W10 compared to BD100 and diesel. In addition, the introduction of water to biodiesel in diesel engine reduces the carbon monoxide and hydrocarbon emissions noticeably.     

The effect of biodiesel oxidation on engine performance and emissions

Biodiesel is an alternative fuel consisting of the alkyl monoesters of fatty acids from vegetable oils or animal fats. Previous research has shown that biodiesel-fueled engines produce less carbon monoxide, unburned hydrocarbons, and particulate emissions compared to diesel fuel. One drawback of biodiesel is that it is more prone to oxidation than petroleum-based diesel fuel. In its advanced stages, this oxidation can cause the fuel to become acidic and to form insoluble gums and sediments that can plug fuel filters. The objective of this study was to evaluate the impact of oxidized biodiesel on engine performance and emissions. A John Deere 4276T turbocharged DI diesel engine was fueled with oxidized and unoxidized biodiesel and the performance and emissions were compared with No. 2 diesel fuel. The neat biodiesels, 20% blends, and the base fuel (No. 2 diesel) were tested at two different loads (100 and 20%) and three injection timings (3° advanced, standard; 3° retarded). The tests were performed at steady-state conditions at a single engine speed of 1400 rpm. The engine performance of the neat biodiesels and their blends was similar to that of No. 2 diesel fuel with the same thermal efficiency, but higher fuel consumption. Compared with unoxidized biodiesel, oxidized neat biodiesel produced 15 and 16% lower exhaust carbon monoxide and hydrocarbons, respectively. No statistically significant difference was found between the oxides of nitrogen and smoke emissions from oxidized and unoxidized biodiesel.     

Effect of biodiesel fuels on diesel engine emissions

The call for the use of biofuels which is being made by most governments following international energy policies is presently finding some resistance from car and components manufacturing companies, private users and local administrations. This opposition makes it more difficult to reach the targets of increased shares of use of biofuels in internal combustion engines. One of the reasons for this resistance is a certain lack of knowledge about the effect of biofuels on engine emissions. This paper collects and analyzes the body of work written mainly in scientific journals about diesel engine emissions when using biodiesel fuels as opposed to conventional diesel fuels. Since the basis for comparison is to maintain engine performance, the first section is dedicated to the effect of biodiesel fuel on engine power, fuel consumption and thermal efficiency. The highest consensus lies in an increase in fuel consumption in approximate proportion to the loss of heating value. In the subsequent sections, the engine emissions from biodiesel and diesel fuels are compared, paying special attention to the most concerning emissions: nitric oxides and particulate matter, the latter not only in mass and composition but also in size distributions. In this case the highest consensus was found in the sharp reduction in particulate emissions.     

Heat transfer and crevice flow in a hydrogen-fueled spark-ignition engine: Effect on the engine performance and NO exhaust emissions

The present work investigates the effect of heat and mass transfer on the combustion process of a hydrogen-fueled spark-ignition engine, using an in-house CFD code. The main scope is to compare the calculated local heat fluxes with the available measured ones, using three heat transfer models of increasing complexity (two existing and one developed by the authors). Moreover, the effect of mass transfer through the crevice regions is also investigated using a phenomenological crevice model. The calculated results (cylinder pressure traces, local heat fluxes and NO exhaust emissions) are compared with the corresponding measured data, at various operating conditions, maintaining constant engine speed and altering the compression ratio and the equivalence ratio. It is revealed, that the proposed heat transfer model is more accurate than the standard wall-function formulation, while with the use of the crevice model a more reliable prediction of engine performance is achieved.     

The effect of biodiesel fuel obtained from waste frying oil on direct injection diesel engine performance and exhaust emissions

In this study, usage of methyl ester obtained from waste frying oil (WFO) is examined as an experimental material. A reactor was designed and installed for production of methyl ester from this kind of oil. Physical and chemical properties of methyl ester were determined in the laboratory. The methyl ester was tested in a diesel engine with turbocharged, four cylinders and direct injection. Gathered results were compared with No. 2 diesel fuel. Engine tests results obtained with the aim of comparison from the measures of torque, power; specific fuel consumptions are nearly the same. In addition, amount of emission such as CO, CO₂, NO_x, and smoke darkness of waste frying oils are less than No. 2 diesel fuel.     

Performance and exhaust emissions of a gasoline engine with ethanol blended gasoline fuels using artificial neural network

The purpose of this study is to experimentally analyse the performance and the pollutant emissions of a four-stroke SI engine operating on ethanol–gasoline blends of 0%, 5%, 10%, 15% and 20% with the aid of artificial neural network (ANN). The properties of bioethanol were measured based on American Society for Testing and Materials (ASTM) standards. The experimental results revealed that using ethanol–gasoline blended fuels increased the power and torque output of the engine marginally. For ethanol blends it was found that the brake specific fuel consumption (bsfc) was decreased while the brake thermal efficiency (η_b.th.) and the volumetric efficiency (η_v) were increased. The concentration of CO and HC emissions in the exhaust pipe were measured and found to be decreased when ethanol blends were introduced. This was due to the high oxygen percentage in the ethanol. In contrast, the concentration of CO₂ and NO_x was found to be increased when ethanol is introduced. An ANN model was developed to predict a correlation between brake power, torque, brake specific fuel consumption, brake thermal efficiency, volumetric efficiency and emission components using different gasoline–ethanol blends and speeds as inputs data. About 70% of the total experimental data were used for training purposes, while the 30% were used for testing. A standard Back-Propagation algorithm for the engine was used in this model. A multi layer perception network (MLP) was used for nonlinear mapping between the input and the output parameters. It was observed that the ANN model can predict engine performance and exhaust emissions with correlation coefficient (R) in the range of 0.97–1. Mean relative errors (MRE) values were in the range of 0.46–5.57%, while root mean square errors (RMSE) were found to be very low. This study demonstrates that ANN approach can be used to accurately predict the SI engine performance and emissions.     

Experimental investigation of the influence of blending on engine emissions of the diesel engine fueled by mahua biodiesel oil

The present article elaborates on the various emission characteristics of mahua oil with diesel fuel in a diesel engine at various blending conditions. Experimental investigation results are studied for various parameters such as exhaust emission of carbon monoxide (CO), hydrocarbon (HC), and oxides of nitrogen (NO) gases and exhaust gas temperature. Results show that residual oxygen, CO, HC, and NO emission were the lowest for mahua biodiesel compared with diesel. The experimental results proved that the use of mahua oil biodiesel as fuel in the diesel engine is a viable alternative to diesel fuel. Mahua biodiesel oil may be beneficial in decreasing greenhouse gas emissions without any engine modification. Mahua oil has the possibility of becoming a sustainable fuel source as biodiesel.     

Effect of ethanol–gasoline blends on engine performance and exhaust emissions in different compression ratios

Renewable energy sources for the gasoline engines alcohols gain importance recently. These renewable energy sources have attracted the attention of researchers as alternative fuel due to their high octane number. In addition, these are also clean energy sources and can be obtained from the biomass alcohols with low carbon like ethanol. In this study, the effect of compression ratio on engine performance and exhaust emissions was examined at stoichiometric air/fuel ratio, full load and minimum advanced timing for the best torque MBT in a single cylinder, four stroke, with variable compression ratio and spark ignition engine.     

Investigation on performance,combustion and emission characteristics of biodiesel - Ethanol blends with hydrogen in CI engine

The current research work focus on the utilization of hydrogen as a fuel in CI engine has been increased tremendously, since it is a zero-emission fuel. But higher self-ignition temperature than conventional fuel, makes to operate in dual fuel mode condition in CI engine. The diesel or biodiesel along with hydrogen in a CI engine results in the improvement in the performance but increase of NO. In order to minimize the NO emission, addition of ethanol with jamun B20 biodiesel blend (biodiesel-diesel-ethanol) and two ternary blends such as B20E05 and B20E10 are formed. In the present study, biodiesel along with H₂ is admitted in the CI engine. Ethanol addition reduces combustion temperature and act as cetane improver for the biodiesel. This induces better combustion of the fuel and reduce NO. The biodiesel production from jamun seed is carried out through transesterification process. H₂ of 4 lpm is allowed at the air inlet and jamun B20 blend is injected through the fuel injector. Improvement of brake thermal efficiency and increase in the NO are observed for the hydrogen with biodiesel operated CI engine. The performance and emission behaviors of CI engine done for the test samples. At full load condition (ternary blend) B20E05 assisted H₂ shows the drastic reduction of NO emission of 8.2% than B20 assist H₂ blend. In other hand emission like hydrocarbon, carbon monoxide and smoke opacity show a notable reduction for B20E05 blend assist H₂ than other test sample fuel. The thermal efficiency is 30.98% for B20E05 assist H₂ and it is 7.55% and 4.7% higher than B20 and B20E05 assist H₂ blend respectively.     

排气温度对乙醇氧化生成甲醛的影响

文章搭建了用于研究乙醇氧化的流反应器试验台,并将流反应器安装在发动机排气管中,借助高温排气对流反应器加热,研究发动机排气温度对流反应器中乙醇氧化生成甲醛的影响。研究结果表明:在恒温和变温环境下,乙醇的质量浓度均随着排气温度的升高而降低,且恒温环境下的乙醇质量浓度明显低于变温环境下的乙醇质量浓度;当排气温度与临界温度相等时,甲醛质量浓度存在最大值4.7μg/L;乙醇的氧化反应以及甲醛的生成与氧化反应均主要发生在温度为733～983 K的条件下;在试验所选的流速范围内,恒温环境下甲醛生成与氧化的临界温度区间为838～869 K。     

Experimental study of engine performance and emissions for hydrogen diesel dual fuel engine with exhaust gas recirculation

With an alarming enlargement in vehicular density, there is a threat to the environment due to toxic emissions and depleting fossil fuel reserves across the globe. This has led to the perpetual exploration of clean energy resources to establish sustainable transportation. Researchers are continuously looking for the fuels with clean emission without compromising much on vehicular performance characteristics which has already been set by efficient diesel engines. Hydrogen seems to be a promising alternative fuel for its clean combustion, recyclability and enhanced engine performance. However, problems like high NOx emissions is seen as an exclusive threat to hydrogen fuelled engines. Exhaust gas recirculation (EGR), on the other hand, is known to overcome the aforementioned problem. Therefore, this study is conducted to study the combined effect of hydrogen addition and EGR on the dual fuelled compression ignition engine on a single cylinder diesel engine modified to incorporate manifold hydrogen injection and controlled EGR. The experiments are conducted for 25%, 50%, 75% and 100% loads with the hydrogen energy share (HES) of 0%, 10% and 30%. The EGR rate is controlled between 0%, 5% and 10%. With no substantial decrement in engine's brake thermal efficiency, high gains in terms of emissions are observed due to synergy between hydrogen addition and EGR. The cumulative reduction of 38.4%, 27.4%, 33.4%, 32.3% and 20% with 30% HES and 10% EGR is observed for NOx, CO2, CO, THC and PM, respectively. Hence, the combination of hydrogen addition and EGR is observed to be advantageous for overall emission reduction.     

Effect of nanoparticles and hydrogen on combustion performance and exhaust emission of corn blended biodiesel in compression ignition engine with advanced timing

In this study, we have evaluated the influence of Zinc oxide and Titanium dioxide nanoparticles addition in hydrogen-corn blended biodiesel combustion performance and exhaust emission using a dual direct-injection compression-ignition engine. 5% of Zinc oxide and Titanium dioxide were mixed with corn-vegetable oil methyl ester under ultrasonication. Results revealed that the addition of nanoparticles improved the Brake power by 22% (Titanium dioxide) and 4% (Zinc oxide). Consequently, 18% and 15% reduction in brake specific fuel consumption indeed at 50% load compared to neat diesel. Furthermore, the addition of nanoparticles also resulted in a reduction of emission values of 37% and 26% in hydrocarbon, 26% and 36% for carbon monoxide, 19% and 15% in nitrogen oxide and followed by 13% and 8% of smoke opacity. Therefore, the results proved that hydrogen-corn biodiesel blended with nanoparticles additive reports a positive effect on compression-ignition diesel engines without major modifications in engine.     

The effect of clove oil and diesel fuel blends on the engine performance and exhaust emissions of a compression-ignition engine

Diesel engines provide the major power source for transportation in the world and contribute to the prosperity of the worldwide economy. However, recent concerns over the environment, increasing fuel prices and the scarcity of fuel supplies have promoted considerable interest in searching for alternatives to petroleum based fuels. Based on this background, the main purpose of this investigation is to evaluate clove stem oil (CSO) as an alternative fuel for diesel engines. To this end, an experimental investigation was performed on a four-stroke, four-cylinder water-cooled direct injection diesel engine to study the performance and emissions of an engine operated using the CSO–diesel blended fuels. The effects of the CSO–diesel blended fuels on the engine brake thermal efficiency, brake specific fuel consumption (BSFC), specific energy consumption (SEC), exhaust gas temperatures and exhaust emissions were investigated. The experimental results reveal that the engine brake thermal efficiency and BSFC of the CSO–diesel blended fuels were higher than the pure diesel fuel while at the same time they exhibited a lower SEC than the latter over the entire engine load range. The variations in exhaust gas temperatures between the tested fuels were significant only at medium speed operating conditions. Furthermore, the HC emissions were lower for the CSO–diesel blended fuels than the pure diesel fuel whereas the NO_x emissions were increased remarkably when the engine was fuelled with the 50% CSO–diesel blended fuel.     

Effect of changing injection pressure on Mahua oil and biodiesel combustion with CeO2 nanoparticle blend on CI engine performance and emission characteristics

Alternative fuels have sparked a lot of interest as oil deposits have decreased and environmental concerns have grown. Biodiesel is an alternative fuel that is being researched as a possible replacement for fossil fuels. In the current investigation, the combustion performance, and emission characteristics of CI(Compression Ignition) engine were examined by changing the fuel injection pressure (180, 200, 220 and 240 bar). The biodiesel (B20) used in this analysis was obtained from Mahua oil at 20% v/v blended with neat diesel (20% Mahua Biodiesel + 80% Diesel). CeO₂(Cerium Oxide) nanoparticles were introduced to the B20 fuel at four distinct concentrations are 25, 50, 75, and 100 ppm. Performance characteristics such as BTE(Brake Thermal Efficiency) and BSFC(Brake Specific Fuel Consumption) were inferior to diesel, at 240 bar B20 with 25 ppm CeO₂ indicated 1.9% increased BTE and 3.8% reduced BSFC compared B20 and 6% lower EGT (Exhaust Gas Temperature) compared diesel. At 200 bar, fuel samples indicated slightly higher In-Cylinder pressure and lower HRR (Heat release rate) compared to diesel. At 200 bar FIP(Fuel Injection Pressure), HC(Hydro Carbon) and CO(Carbon Monoxide) emissions were reduced significantly compared to diesel. The largest reduction in smoke opacity and NOx(Nitrous Oxide) emissions were observed at 240 bar with 75 ppm dosage, but CO₂(Carbon Dioxide) emissions were higher at 220 bar.     

The effect of biodiesel and bioethanol blended diesel fuel on nanoparticles and exhaust emissions from CRDI diesel engine

Biofuel (biodiesel, bioethanol) is considered one of the most promising alternative fuels to petrol fuels. The objective of the work is to study the characteristics of the particle size distribution, the reaction characteristics of nanoparticles on the catalyst, and the exhaust emission characteristics when a common rail direct injection (CRDI) diesel engine is run on biofuel-blended diesel fuels. In this study, the engine performance, emission characteristics, and particle size distribution of a CRDI diesel engine that was equipped with a warm-up catalytic converters (WCC) or a catalyzed particulate filter (CPF) were examined in an ECE (Economic Commission Europe) R49 test and a European stationary cycle (ESC) test. The engine performance under a biofuel-blended diesel fuel was similar to that under D100 fuel, and the high fuel consumption was due to the lowered calorific value that ensued from mixing with biofuels. The use of a biodiesel–diesel blend fuel reduced the total hydrocarbon (THC) and carbon monoxide (CO) emissions but increased nitrogen oxide (NO_x) emissions due to the increased oxygen content in the fuel. The smoke emission was reduced by 50% with the use of the bioethanol–diesel blend. Emission conversion efficiencies in the WCC and CPF under biofuel-blended diesel fuels were similar to those under D100 fuel. The use of biofuel-blended diesel fuel reduced the total number of particles emitted from the engine; however, the use of biodiesel–diesel blends resulted in more emissions of particles that were smaller than 50 nm, when compared with the use of D100. The use of a mixed fuel of biodiesel and bioethanol (BD15E5) was much more effective for the reduction of the particle number and particle mass, when compared to the use of BD20 fuel.     

Effect of hydrogen addition on combustion and emissions performance of a spark-ignited ethanol engine at idle and stoichiometric conditions

Regarding the limited fossil fuel reserves, the renewable ethanol has been considered as one of the substitutional fuels for spark ignition (SI) engines. But due to its high latent heat, ethanol is usually hard to be well evaporated to form the homogeneous fuel–air mixture at low temperatures, e.g., at idle condition. Compared with ethanol, hydrogen possesses many unique combustion and physicochemical properties that help improve combustion process. In this paper, the performance of a hydrogen-enriched SI ethanol engine under idle and stoichiometric conditions was investigated. The experiment was performed on a modified 1.6 L SI engine equipped with a hydrogen port-injection system. The ethanol was injected into the intake ports using the original engine gasoline injection system. A self-developed hybrid electronic control unit (HECU) was adopted to govern the opening and closing of hydrogen and ethanol injectors. The spark timing and idle bypass valve opening were governed by the engine original electronic control unit (OECU), so that the engine could operate under its original target idle speed for each testing point. The engine was first fueled with the pure ethanol and then hydrogen volume fraction in the total intake gas was gradually increased through increasing hydrogen injection duration. For a specified hydrogen addition level, ethanol flow rate was reduced to keep the hydrogen–ethanol–air mixture at stoichiometric condition. The test results showed that hydrogen addition was effective on reducing cyclic variations and improving indicated thermal efficiency of an ethanol engine at idle. The fuel energy flow rate was reduced by 20% when hydrogen volume fraction in the intake rose from 0% to 6.38%. Both flame development and propagation periods were shortened with the increase of hydrogen blending ratio. The heat transfer to the coolant was decreased and the degree of constant volume combustion was enhanced after hydrogen addition. HC and CO emissions were first reduced and then increased with the increase of hydrogen blending fraction. The acetaldehyde emission from the hydrogen-enriched ethanol engine is lower than that from the pure ethanol engine. However, the addition of hydrogen tended to increase NO_x emissions from the ethanol engine at idle and stoichiometric conditions.