Dependence of current-voltage characteristics of pseudomorphic AlAs/In0.53a0.47s/InAs resonant tunneling diodes on quantum well widths

This paper studies the dependence of I-V characteristics on quantum well widths in AlAs/In_0.53Ga_0.47As and AlAs/In_0.53Ga_0.47As/InAs resonant tunneling structures grown on InP substrates. It shows that the peak and the valley current density in the negative differential resistance region are closely related with quantum well width. The measured peak current density, valley current densities and peak-to-valley current ratio of resonant tunneling diodes are continually decreasing with increasing well width.     

Nanoelectronic devices---resonant tunnelling diodes grown on InP substrates by molecular beam epitaxy with peak to valley current ratio of 17 at room temperature

This paper reports that InAs/In$_{0.53}$Ga$_{0.47}$As/AlAs resonant tunnelling diodes have been grown on InP substrates by molecular beam epitaxy. Peak to valley current ratio of these devices is 17 at 300K. A peak current density of 3kA/cm$^{2}$ has been obtained for diodes with AlAs barriers of ten monolayers, and an In$_{0.53}$Ga$_{0.47}$As well of eight monolayers with four monolayers of InAs insert layer. The effects of growth interruption for smoothing potential barrier interfaces have been investigated by high resolution transmission electron microscope.     

Effects of AlN nucleation layer thickness on crystal quality of AlN grown by plasma-assisted molecular beam epitaxy

In this paper,the effects of thickness of AlN nucleation layer grown at high temperature on AlN epi-layer crystalline quality are investigated.Crack-free AlN samples with various nucleation thicknesses are grown on sapphire substrates by plasma-assisted molecular beam epitaxy.The AlN crystalline quality is analysed by transmission electron microscope and x-ray diffraction (XRD) rocking curves in both (002) and (102) planes.The surface profiles of nucleation layer with different thicknesses after in-situ annealing are also analysed by atomic force microscope.A critical nucleation thickness for realising high quality AlN films is found.When the nucleation thickness is above a certain value,the (102) XRD full width at half maximum (FWHM) of AlN bulk increases with nucleation thickness increasing,whereas the (002) XRD FWHM shows an opposite trend.These phenomena can be attributed to the characteristics of nucleation islands and the evolution of crystal grains during AlN main layer growth.     

Quantum dots-templated growth of strain-relaxed GaN on a c-plane sapphire by radio-frequency molecular beam epitaxy

We investigated the quantum dots-templated growth of a(0001) GaN film on a c-plane sapphire substrate.The growth was carried out in a radio-frequency molecular beam epitaxy system.The enlargement and coalescence of grains on the GaN quantum dots template was observed in the atom force microscopy images,as well as the more ideal surface morphology of the GaN epitaxial film on the quantum dots template compared with the one on the AlN buffer.The Ga polarity was confirmed by the reflected high energy electron diffraction patterns and the Raman spectra.The significant strain relaxation in the quantum dots-templated GaN film was calculated based on the Raman spectra and the X-ray rocking curves.Meanwhile,the threading dislocation density in the quantum dots-templated film was estimated to be 7.1×107cm-2,which was significantly suppressed compared with that of the AlN-buffered GaN film.The roomtemperature Hall measurement showed an electron mobility of up to 1860cm2 /V·s in the two-dimensional electron gas at the interface of the Al 0.25Ga0.75 N/GaN heterojunction.     

Piezoelectric polarization and quantum size effects on the vertical transport in AlGaN/GaN resonant tunneling diodes

In this work,the electronic properties of resonant tunneling diodes(RTDs) based on GaN-AlxGa(1-x)N double barriers are investigated by using the non-equilibrium Green functions formalism(NEG).These materials each present a wide conduction band discontinuity and a strong internal piezoelectric field,which greatly affect the electronic transport properties.The electronic density,the transmission coefficient,and the current–voltage characteristics are computed with considering the spontaneous and piezoelectric polarizations.The influence of the quantum size on the transmission coefficient is analyzed by varying GaN quantum well thickness,Al_xGa_(1-x)N width,and the aluminum concentration x_(Al).The results show that the transmission coefficient more strongly depends on the thickness of the quantum well than the barrier;it exhibits a series of resonant peaks and valleys as the quantum well width increases.In addition,it is found that the negative differential resistance(NDR) in the current–voltage(I–V) characteristic strongly depends on aluminum concentration xAl.It is shown that the peak-to-valley ratio(PVR) increases with xAlvalue decreasing.These findings open the door for developing vertical transport nitrides-based ISB devices such as THz lasers and detectors.     

Polarity control and residual strain in ZnO epilayers grown by molecular beam epitaxy on (0001) GaN/sapphire

We report on the polarity control of ZnO grown by plasma assisted molecular beam epitaxy on Ga polar (0001) GaN/sapphire templates simply via the oxygen‐to‐Zn (VI/II) ratio during the growth of a thin nucleation layer at 300 °C. Following Zn pre‐exposure, the ZnO layers nucleated with low VI/II ratios (<1.5) exhibited Zn‐polarity. Those nucleated with VI/II ratios above 1.5, exhibited O‐polarity. Supported by scanning transmission electron microscopic imaging, we have unequivocally demonstrated that polarity inversion takes place without formation of any vertical inversion domains and within one monolayer of presumably non‐stoichiometric GaO_x formed at the ZnO/GaN interface. A direct correlation between polarity and strain sign of ZnO layers has been found. The Zn‐polar ZnO layers were under tensile biaxial strain, whereas the O‐polar material exhibited compressive strain. Moreover, the amount of residual strain varied linearly with VI/II ratio used during the low‐temperature nucleation layer growth. Strain control with VI/II ratio has been explained by the potential formation of Zn interstitials.     

Influence of spacer layer thickness on the current-voltage characteristics of pseudomorphic AlAs/In0.53Ga0.47As/InAs resonant tunnelling diodes

This paper investigates the dependence of current voltage characteristics of AlAs/In0.53Ga0.47As/InAs resonant tunnelling diodes （RTDs） on spacer layer thickness. It finds that the peak and the valley current density J in the negative differential resistance （NDR） region depends strongly on the thickness of the spacer layer. The measured peak to valley current ratio of RTDs studied here is shown to improve while the current density through RTDs decreases with increasing spacer layer thickness below a critical value.     

Surface kinetics of GaN evaporation and growth by molecular-beam epitaxy

The kinetics of surface processes during the growth of GaN by molecular-beam epitaxy (MBE) with ammonia as the source of reactive nitrogen is studied theoretically and experimentally. A model of surface processes is developed taking into account specific effects of the blocking of NH₃ adsorption sites by Group III and Group V surface species. Parameters of the model (respective kinetic rate constants) are determined from comparison with experimental data. It is shown that the evaporation rate of GaN in ammonia atmosphere is much lower than that in vacuum. Kinetics of GaN growth under gallium-rich and nitrogen-rich conditions are compared. Under nitrogen-rich conditions the GaN surface is predicted to be enriched by NH_x surface radicals, in contrast to the case of growth under gallium-rich conditions or of free evaporation in vacuum. It is shown that use of the nitrogen-rich conditions allows one to increase the growth temperature by 80–90°C compared with the case of gallium-rich conditions or plasma-activated MBE. The increased growth temperature is favorable in improving the optical and electrical properties of the material grown.     

Comparison of resonant tunneling in AlGaAs/GaAs parabolic and diffusion modified quantum wells

Double barrier resonant tunneling diode using annealing induced diffusion modified quantum well is proposed as a viable alternative to that using parabolic quantum well which requires complex techniques to fabricate it. The transmission coefficients are calculated using the hybrid incremental airy function plane wave approach. The room temperature current-voltage characteristics have been calculated using transmission coefficients. The current-voltage characteristics are found to be similar in both diodes.     

A study of estimation method for conduction band offset in semiconductor heterostructure by using triple-barrier resonant tunneling diodes

A method for evaluating a band offset of a heterojunction is proposed by measuring temperature dependence of current–voltage (I–V) characteristics in triple-barrier resonant tunneling diodes (TBRTDs). The method was applied for investigating a conduction band offset by using GaAs_0.25P_0.75/GaAs TBRTDs with thin strain heterobarriers grown by MOCVD and ΔE_c was estimated as 200–240 meV. In the strain-barrier TBRTDs, negative differential resistance was observed below 100 K.     

Comparison of blue–green response between transmission-mode GaAsP-and GaAs-based photocathodes grown by molecular beam epitaxy

In order to develop the photodetector for effective blue–green response, the 18-mm-diameter vacuum image tube combined with the transmission-mode Al_(0.7)Ga_(0.3)As_(0.9)P_(0.1)/GaAs_(0.9)P_(0.1) photocathode grown by molecular beam epitaxy is tentatively fabricated. A comparison of photoelectric property, spectral characteristic and performance parameter between the transmission-mode GaAsP-based and blue-extended GaAs-based photocathodes shows that the GaAsP-based photocathode possesses better absorption and higher quantum efficiency in the blue–green waveband, combined with a larger surface electron escape probability. Especially, the quantum efficiency at 532 nm for the GaAsP-based photocathode achieves as high as 59%, nearly twice that for the blue-extended GaAs-based one, which would be more conducive to the underwater range-gated imaging based on laser illumination. Moreover, the simulation results show that the favorable blue–green response can be achieved by optimizing the emission-layer thickness in a range of 0.4 μm–0.6 μm.     

Relationship between the electric performance and the photoluminescence spectra of resonant tunnelling diodes

Resonant tunnelling diodes with different structures were grown. Their photoluminescence spectra were investigated. By contrast, the luminescence in the quantum well is separated from that of other epilayers. The result is obtained that the exciton of the luminescence in the quantum well is partly come from the cap layer in the experiment. So the photoluminescence spectrum is closely related to the electron transport in the resonant tunnelling diode structure. This offers a method by which the important performance of resonant tunnelling diode could be forecast by analysing the integrated photoluminescence intensities.     

Comparison of organic thin films deposited by supersonic molecular-beam epitaxy and organic molecular-beam epitaxy: The case of titanyl phthalocyanine

Recently, supersonic molecular-beam epitaxy (SuMBE) was invented as an alternative method for the deposition of organic material, using higher kinetic energies for deposition than conventional organic molecular-beam epitaxy (OMBE). Using titanyl phthalocyanine (TiOPc) as a model substance, we show that the SuMBE deposition results in increased crystal quality of the deposited material. This is induced by the high kinetic energy of the molecular-beam in SuMBE, which leads to increased molecular mobility on the surface, resulting in larger crystal sizes and higher crystal quality. Alternatively, similar films as made by OMBE can be deposited by SuMBE at lower substrate temperatures. This temperature reduction may be of interest for the deposition of stacked organic devices on underlying heat sensitive layers, as they are quite common in organic electronic devices.     

Optical properties and structural characteristics of ZnO thin films grown on a-plane sapphire substrates by plasma-assisted molecular beam epitaxy

We investigated structural and optical properties of ZnO thin films grown on (112?0) a-plane sapphire substrates using plasma-assisted molecular beam epitaxy. Negligible biaxial stress in ZnO thin films is due to the use of (112?0) a-plane sapphire substrates and slow substrate cooling. The 14 K photoluminescence spectrum shows a blueshift of energy positions compared with ZnO single crystal. A donor with binding energy of 43 meV and an acceptor with binding energy of ～170 meV are identified by well-resolved photoluminescence spectra. A characteristic emission band at 3.320 eV (so-called A-line) is studied. Based on analysis from photoluminescence spectra, the origin of the A-line, it seems, is more likely an (e, A°) transition, in which defect behaves as an acceptor. The room-temperature photoluminescence is dominated by the FX at 3.307 eV, which is an indication of strongly reduced defect density in ZnO thin films.     

Influence of Ga coverage on the sizes of GaAs quantum dash pairs grown by high temperature droplet epitaxy

We investigate the formation of GaAs quantum dash pairs with different coverages by droplet epitaxy. The GaAs quantum dash pairs of various sizes are fabricated by high temperature droplet epitaxy. Dual‐sized quantum dash pairs are observed along $[01\bar 1]$ orientation. Depending on the Ga cov‐ erage, the width of the quantum dash pairs can be tuned from ～100 nm to ～300 nm while keeping the height in the range of 4 nm to 10 nm. The coverage dependence of quantum dash pairs is also confirmed with photoluminescence measurement. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microstructural properties of GaN grown on a Si(110) substrate by gas-source molecular beam epitaxy: Dependence on the ammonia flux

The microstructural properties of a GaN thin film grown on a Si(110) substrate under various ammonia (NH₃)-flux conditions were observed to study growth mode and defect evolution. The surface flatness of GaN thin films was improved with the increase of the NH₃ flux while the thickness was decreased by increasing the NH₃ flux. In addition, the crystalline quality of the GaN film grown under the lower NH₃ flux (100 sccm) was better than that of the film under the higher NH₃ flux (400 sccm). The different dislocation behaviors depending on NH₃ fluxes were observed; the low density of dislocations was measured and most of dislocations penetrating the thin film was mixed- and edge-type dislocations when GaN was grown under the low NH₃ flux condition while the high density of dislocation and many mixed- and screw-type dislocations penetrating the film were observed in the GaN film grown under the high NH₃ flux. These phenomena are demonstrated by using a kinetic model related to the role of NH₃.     

分子束外延法在Sapphire衬底上生长的Zn1－xMgxO薄膜折射率及厚度的测试

利用偏振光椭圆率测量仪对分子束外延(MBE)法在Sapphire衬底上生长的Zn_1-xMg_xO 薄膜的薄膜折射率和厚度进行了测试. 结合ICP法测得的薄膜中的Mg组成量，经数值拟合，导出表征薄膜厚度与薄膜生长条件、薄膜折射率与薄膜中的Mg组成量之间关系的曲线，为MBE法在Sapphire衬底上生长Zn_1-xMg_xO 薄膜时控制薄膜厚度以及在制作Zn_1-xMg_xO 薄膜的波导时控制薄膜的折射率提供了理论依据. 关键词： ZnMgO薄膜 偏振光椭圆率测量仪 折射率 分子束外延(MBE)     

基于分子束外延生长的1.05 eV InGaAsP的超快光学特性研究

利用分子束外延方法制备了应用于四结光伏电池的1.05 eV InGaAsP薄膜, 并对其超快光学特性进行了研究. 温度和激发功率有关的发光特性表明: InGaAsP材料以自由激子发光为主. 室温下InGaAsP材料的载流子发光弛豫时间达到10.4 ns, 且随激发功率增大而增大. 发光弛豫时间随温度升高呈现S形变化, 在低于50 K时随温度升高而增大, 在50–150 K之间时减小, 而温度高于150 K时再次增大. 基于载流子弛豫动力学, 分析并解释了温度及非辐射复合中心浓度对样品材料载流子发光弛豫时间S形变化的影响.     

Microstructural study of MBE-grown ZnO film on GaN/sapphire (0001) substrate

Single crystalline ZnO film is grown on GaN/sapphire (0001) substrate by molecular beam epitaxy. Ga₂O₃ is introduced into the ZnO/GaN heterostructure intentionally by oxygen-plasma pre-exposure on the GaN surface prior to ZnO growth. The crystalline orientation and interfacial microstructure are characterized by X-ray diffraction and transmission electron microscopy. X-ray diffraction analysis shows strong c-axis preferred orientation of the ZnO film. Cross-sectional transmission electron microscope images reveal that an additional phase is formed at the interface of ZnO/GaN. Through a comparison of diffraction patterns, we confirm that the interface layer is monoclinic Ga₂O₃ and the main epitaxial relationship should be and .      

分子束外延制备的垂直易磁化MnAl薄膜结构和磁性

系统地研究了利用分子束外延方法在GaAs(001) 衬底上外延生长的MnAl_x薄膜的结构和垂直易磁化特性随组分及生长温度的依赖关系. 磁性测试表明, 可在较大组分范围内 (0.4≤x≤1.2) 获得大矫顽力的垂直易磁化MnAl_x薄膜, 然而同步辐射X射线衍射和磁性测试发现当x≤0.6时MnAl薄膜出现较多的软磁相, 当x >0.9时, MnAl薄膜晶体质量和化学有序度逐渐降低, 组分为MnAl_0.9时制备的薄膜有最好的[001]取向. 随着生长温度的增加, MnAl_0.9薄膜的有序度、垂直磁各向异性常数、矫顽力和剩磁比均增加, 350℃时制备的MnAl_0.9薄膜化学有序度高达0.9, 其磁化强度、剩磁比、矫顽力和垂直磁各向异性常数分别为265emu/cm³、93.3%、8.3kOe (1 Oe=79.5775A/m)和7.74Merg/cm³ (1 erg=10^-7J). 不含贵金属及稀土元素、良好的垂直易磁化性质、 与半导体材料结构良好的兼容性以及磁性能随不同生长条件的可调控 性使得MnAl薄膜有潜力应用于多种自旋电子学器件. 关键词： 分子束外延 大矫顽力材料 磁各向异性