Tribo-mechanical characterization of reinforced epoxy resin under dry and lubricated contact conditions

The aim of the present work is to investigate the influence of the reinforcing material and architecture on the voids content, mechanical properties and tribological behavior of fiber reinforced epoxy composite laminates manufactured by VARTM under different processing conditions. Two different textile architectures, namely unidirectional non-crimp fabrics (UD) and 0/90 plain wave (PW), were considered, reinforcing an EPIKOTE RIMR 135 epoxy matrix with glass (GF) as well as carbon (CF) continuous fibers. Optical observations revealed an unexpected trend relatively to the intra- and inter-bundle voids concentration with respect to the impregnation velocity, especially using UD-CF and UD-GF reinforcements and low impregnation rate. Tensile and three points bending tests highlighted the dominant role of fiber material and architecture on mechanical properties, whereas the presence of voids played a minor role with respect to the analyzed features. Tribological outcomes evidenced a reduction of the friction coefficient (μ) when the resin is reinforced by carbon or glass fibers. The lowest values were detected when the sliding direction of the counterbody is oriented parallel to the fiber direction for UD samples. Further reduction of μ, for both UD and PW specimens, was obtained by interposing a lubricant at the interface.     

Fluorinated graphene reinforced polyimide films with the improved thermal and mechanical properties

In order to explore the addition effect of fluorinated graphene (FG) on the mechanical and thermal performances of polyimide (PI) matrix, FG sheets are first prepared and employed as the nanofillers to construct PI/FG nanocomposite films. The prepared film is optically transparent at low content of FG and experimental results demonstrate that the addition of FG can effectively enhance the properties of PI matrix. Especially, compared with pure PI matrix, the addition of 0.5 wt% FG in PI can endow 30.4% increase in tensile stress and 115.2% increase in elongation at break. Experimental analyses considering the morphology and microstructure are also conducted, and the results indicate that the improved mechanical properties of the PI/FG nanocomposite films are mainly attributed to the good dispersibility of FG sheets in PI host, and the effective stress transfer between the polymer and the FG.     

Hybrid effect of nanoparticles with carbon fibers on the mechanical and wear properties of polymer composites

Polyetheretherketone (PEEK) composites reinforced with carbon fibers (CFs) and nano-ZrO₂ particles were prepared by incorporating nanoparticles into PEEK/CF composites via twin-screw extrusion. The effects of nanoparticles on the mechanical and wear properties of the PEEK/CF composites were studied. The results showed that the incorporation of nano-ZrO₂ particles with carbon fiber could effectively enhance the tensile properties of the composites. The tensile strength and Young’s modulus of the composites increased with the increasing nano-ZrO₂ content. The enhancement effect of the particle was more significant in the hybrid reinforced composites. The compounding of the two fillers also remarkably improved the wear resistance of the composites under water condition especially under high pressures. It was revealed that the excellent wear resistance of the PEEK/CF/ZrO₂ composites was due to a synergy effect between the nano-ZrO₂ particles and CF. CF carried the majority of load during sliding process and prevented severe wear to the matrix. The incorporation of nano-ZrO₂ effectively inhibited the CF failures through reducing the stress concentration on the carbon fibers interface and the shear stress between two sliding surfaces. It was also indicated that the wear rates of the hybrid composites decreased with the increasing applied load and sliding distance under water lubrication. And low friction coefficient and low wear rate could be achieved at high sliding velocity.     

Tunable BT@SiO2 core@shell filler reinforced polymer composite with high breakdown strength and release energy density

Barium titanate@silicon dioxide (BT@SiO₂) core@shell fillers with an average diameter of 100 nm were prepared by a facile sol–gel synthesis. The thickness of SiO₂ shell can be easily tuned by varying different mass ratio of BT to tetraethyl orthosilicate (TEOS). Polyvinylidene fluoride (PVDF) based composite films reinforced by BT and BT@SiO₂ were fabricated via a solution casting method. The effects of SiO₂ shell on morphology structure, wettability, interfacial adhesion, dielectric, electrical and energy performances of composites were investigated. Compared with BT/PVDF, BT@SiO₂/PVDF composites show significantly increased breakdown strength due to enhanced interfacial adhesion and suppressed charge carrier conduction. Benefiting from enhanced breakdown strength and reduced remnant polarization induced by SiO₂ shell, BT@SiO₂/PVDF shows increased release energy density (energy density which can be fully discharged and applicable). Especially, BT@SiO₂/PVDF with SiO₂ thickness of 4 nm exhibits the highest release energy density of 1.08 J/cm³ under applied electric field of 145 kV/mm.     

Preparation, morphology and properties of acylchloride-grafted multiwall carbon nanotubes/fluorinated polyimide composites

A fluorinated polyimide (PI) was synthesized by a two-step reaction from 4,4′-(hexafluoroisopropylidene) diphthalic anhydride and 2,2′-bis(trifluoromethyl)-4,4′diaminobiphenyl. A series of PI composites with various mass fractions of multi-walled carbon nanotubes (MWNTs) were prepared by either an in situ polymerization or blending process. To increase the chemical compatibility of carbon nanotubes with the PI matrix, MWNTs were treated with an acid mixture and sulfoxide chloride by turns. Results show that the dispersion of the MWNTs is highly improved in the PI by modification. The modified MWNTs are dispersed homogeneously in the matrix, while the structures of the PI and MWNTs are stable in the preparation process. The thermal stability of the nanocomposites is slightly lower than that of the pure PI. With incorporating MWNTs, the storage modulus and glass transition temperature of the composite films enhanced comparing to that of PI matrix. The dielectric constants of the composites increase sharply, which is favorable to their practical use in anti-static materials and embedded capacitors.     

Evaluation of the interfacial properties of polypropylene composite laminates,reinforced with paper sheets

Laminates, composed of different papers and polypropylene (PP), were fabricated by a manual stacking and hot pressing. The laminates were characterized by mechanical testing and the results were compared to glass fiber reinforced PP. Furthermore, a detailed evaluation of the interfacial properties and the paper structures was carried out by means of data modeling via rule of mixtures (ROM), as well as electron microscope (SEM) analysis. For investigating the influence of the laminate’s composition on the water adsorption behavior, water diffusion coefficients were determined. As a result, laminates with a tensile modulus up to 6 GPa and a tensile strength of 80 MPa were obtained. The property changes of the papers upon processing were successfully modeled, revealing a significant increase of the paper’s mechanical properties after fiber embedding. In general, the obtained results indicate a high potential of paper as a suitable reinforcement material for low to middle strained applications.     

In situ preparation of reinforced polyimide nanocomposites with the noncovalently dispersed and matrix compatible MWCNTs

High performance MWCNT-reinforced polyimide nanocomposites were prepared through in situ polymerization route. 2,6-Diaminoanthraquinone (2,6-DAAQ) was selected to serve as both a diamine comonomer, and a noncovalent dispersant of MWCNTs through π–π interaction. The good dispersion of MWCNTs in both solution and polymer matrix, and high compatibility derived from the structural similarity have been proved to be particularly advantageous for the interfacial adhesion and load transfer from the polymer matrix to MWCNTs. The nanocomposites with 0.50–0.75 wt% MWCNTs had the most excellent thermal stability, thermomechanical and tensile properties, and the electrical conductivity also achieved a sharp increase at such low content. The load transfer efficiency was calculated based on both theoretical model and microscopical size measurement, and the results were rather reasonable within accepted error range.     

Processing of graphene nanoribbon based hybrid composite for electromagnetic shielding

The advent of graphene heralded by the recent studies on carbon based conducting polymer composites has been a motivation for the use of graphene as an electromagnetic interference (EMI) shielding material. One of the variants of graphene, graphene nanoribbon (GNR) shows remarkably different properties from graphene. The EMI shielding effectiveness of the composite material mainly depends on fillers’ intrinsic conductivity, dielectric constant and aspect ratio. We have synthesized graphene nanoribbon (GNR) – Polyaniline (PANI) – epoxy composite film for effective shielding material in the X-band frequency range of 8.2–12.4 (GHz). We have performed detailed studies of the EMI shielding effect and the performance of the composite and found that the composite shows ∼−40 dB shielding which is sufficient to shield more than 95% of the EM waves in X Band. We checked the shielding effectiveness of the composite film by varying the GNR percentage and the thickness of the film. The strength properties of the synthesized composited were also studied with a aim to have a material having both high strength and EMI shielding properties.     

Enhanced thermal conductivity and retained electrical insulation for polyimide composites with SiC nanowires grown on graphene hybrid fillers

Polyimide (PI) composites containing one-dimensional SiC nanowires grown on two-dimensional graphene sheets (1D–2D SiC_NWs-GSs) hybrid fillers were successfully prepared. The PI/SiC_NWs-GSs composites synchronously exhibited high thermal conductivity and retained electrical insulation. Moreover, the heat conducting properties of PI/SiC_NWs-GSs films present well reproducibility within the temperature range from 25 to 175 °C. The maximum value of thermal conductivity of PI composite is 0.577 W/mK with 7 wt% fillers loading, increased by 138% in comparison with that of the neat PI. The 1D SiC nanowires grown on the GSs surface prevent the GSs contacting with each other in the PI matrix to retain electrical insulation of PI composites. In addition, the storage modulus and Young’s modulus of PI composites are remarkably improved in comparison with that of the neat PI.     

Effects of functional groups on the graphene sheet for improving the thermomechanical properties of polyurethane nanocomposites

Dispersibility of graphene sheets in polymer matrices and interfacial interaction are challenging for producing graphene-based high performance polymer nanocomposites. In this study, three kinds nanofillers; pristine graphene nanoplatelets (GNPs), graphene oxide (GO), and functionalized graphene sheet (FGS) were used to prepare polyurethane (PU) composite by in-situ polymerization. To evaluate the efficacy of functional groups on the graphene sheets, PU reinforced with GNPs, GO, and FGS were compared through tensile testing and dynamic mechanical thermal analysis. The Young's moduli of 2 wt% GO and FGS based PU nanocomposites were found significantly higher than that of same amount of GNPs loading as an evidence of the effect of functional groups on graphene sheets for the mechanical reinforcement. The strong interaction of FGS with PU was responsible to exhibit notably high modulus (25.8 MPa) of 2 wt% FGS/PU composite than the same amount of GNPs and GO loading even at elevated temperature (100 °C).     

Surface performance and physical properties of nanoscale ceramics reinforced laser alloying composite coatings

Si₃N₄–Ni60 is firstly used to improve the wear resistance of a TA7 (Ti–5Al–2.5Sn) titanium alloy surface by mean of a laser alloying (LA) technique. The synthesis of the hard composite coating on a TA7 titanium alloy by LA of Ni60–Si₃N₄ pre-placed powders was investigated by means of scanning electron microscope (SEM), energy dispersive spectrometer (EDS) and high resolution transmission electron microscope (HRTEM). Experimental results indicated that a number of the interdendritic lamellar eutectics, nanoscale ceramics (NC) and the amorphous phases were produced in such LA coating. The production of NC led the free energy to enhance, which increased the density of point defect, leading to the formation of hypersaturated state of point defect, causing lattice distortions. Compared with a TA7 alloy substrate, an improvement of the wear resistance was obtained for such LA composite coating.     

Fluorographene/polyimide composite films: Mechanical,electrical, hydrophobic,thermal and low dielectric properties

Nowadays, dielectric materials with excellent mechanical and hydrophobic properties are desired for use in the integrated circuits (ICs). For this reason, low dielectric constant fluorographene/polyimide (FG/PI) composite films were prepared by a facile solution blending method, suggesting that the mechanical, electrical, hydrophobic and thermal properties were significantly enhanced in the presence of FG. With addition of 1 wt% FG, the tensile strength, Young’s modulus and elongation at break were dramatically increased by 139%, 33% and 18% respectively when compared with pure PI film. Furthermore, composite films exhibit superior hydrophobic and thermal stability performance. Especially, the FG/PI film with 0.5 wt% of FG possessing a low dielectric constant of 2.48 and a good electrical insulativity that is lower than 10⁻¹⁴ S m⁻¹. Therefore, by their excellent performance, FG/PI hybrid films represent suitable candidate solutions with applications in the microelectronics and aerospace industries.     

A novel process to improve yield and mechanical performance of bamboo fiber reinforced composite via mechanical treatments

The aims of the present study are to produce bamboo fiber reinforced composite (BFRC) with high yield and to investigate the mechanical properties of BFRC comparing with those of commercial bamboo scrimber (BS) and laminated bamboo lumber (LBL). A novel process was developed for production of BFRC using oriented bamboo fiber mat (OBFM) made by a pilot machine. The yield and the mechanical properties of BFRC were investigated and analyzed in comparing with those of raw bamboo and other bamboo-based composites. The results show that the novel process produces 92.54% yield of OBFM due to without any chemical and special removing of inner and outer layer of bamboo during processing. In addition, all the mechanical properties and the variability of BFRC were significantly enhanced comparing with those of raw bamboo and other bamboo-based composites.     

Enhancement of dielectric and electrical properties in BT/SiC/PVDF three-phase composite through microstructure tailoring

A polymer composite with high dielectric permittivity was prepared by embedding silicon carbide (SiC) whisker with an average diameter of 500 nm–1 μm in poly(vinylidene fluoride) (PVDF). However, the high dielectric loss and electrical conductivity of the two-phase composite prohibits its potential applications. Barium titanate (BT) particles with average diameter of 100 nm and 1 μm were incorporated as a third phase to fabricate a three-phase composite. The morphology structure, dielectric and electrical properties before and after the addition of BT particles were investigated. The three-phase composite exhibits largely suppressed dielectric loss and electrical conductivity without sacrificing the high dielectric permittivity, which was extremely hard to be realized for two-phase composite. It is also found that the nano-size BT is more favorable in achieving high dielectric permittivity than the micro-size BT, where their dielectric loss and electrical conductivity are similar. Furthermore, electric modulus analysis confirms the largely suppressed electron conduction process which results in the enhanced dielectric and electrical properties in three-phase composite.     

Mechanical properties of carbon nanotube reinforced polymer nanocomposites: A coarse-grained model

In this work, a coarse-grained (CG) model of carbon nanotube (CNT) reinforced polymer matrix composites is developed. A distinguishing feature of the CG model is the ability to capture interactions between polymer chains and nanotubes. The CG potentials for nanotubes and polymer chains are calibrated using the strain energy conservation between CG models and full atomistic systems. The applicability and efficiency of the CG model in predicting the elastic properties of CNT/polymer composites are evaluated through verification processes with molecular simulations. The simulation results reveal that the CG model is able to estimate the mechanical properties of the nanocomposites with high accuracy and low computational cost. The effect of the volume fraction of CNT reinforcements on the Young's modulus of the nanocomposites is investigated. The application of the method in the modeling of large unit cells with randomly distributed CNT reinforcements is examined. The established CG model will enable the simulation of reinforced polymer matrix composites across a wide range of length scales from nano to mesoscale.     

Electrical conductivity and interlaminar shear strength enhancement of carbon fiber reinforced polymers through synergetic effect between graphene oxide and polyaniline

Utilizing synergetic effect of different ingredients is an important strategy to design new multi-functional composites. In this work, high-strength graphene oxide and conductive polyaniline were selected to dope into divinylbenzene to fabricate a new type carbon fiber reinforced polymer laminates, where a cooperative improvement of through-thickness electrical conductivity and interlaminar shear strength was observed. With addition of 15 wt% of PANI-GO at the optimized weight ratio of 60:1 in the CF/DVB-PANI-GO, 150% enhancement of the electrical conductivity compared to the CF/DVB-PANI, and 76% enhancement of the ILSS compared to the CF/DVB-GO were realized. Our laminates reach 66% in ILSS of that for the conventional CFRP made of epoxy, but the former features about 103 times higher AC conductivity. The mechanism for such a synergic enhancement for both electrical and mechanical performance was investigated by rheology measurement and scanning electron microscopy, where uniform 3-D network formed by PANI/GO has been clearly observed.     

Relation between repeated uniaxial compressive pressure and electrical resistance of carbon nanotube filled silicone rubber composite

Carbon nanotube filled polymer composite can be used as sensitive material of flexible pressure sensor. By using solution mixing method, carbon nanotubes are dispersed into silicone rubber matrix to fabricate the composite. The piezoresistivities of the composite with different carbon nanotube concentrations under repeated compressions are researched quantitatively. The monotonicity of the piezoresistivity is dependent on the content of carbon nanotube and the range of the applied pressure. The reproducibility error of the piezoresistivity decreases with the increase of the compression cycles. The experimental data of the piezoresistivity are fitted by the linear combination of two exponential functions. The piezoresistive mechanism is studied qualitatively by analyzing the changes in the carbon nanotube network.     

Functional shape memory composite nanofibers with graphene oxide filler

In the present study, we prepared a series of graphene oxide (GO) filled shape memory polyurethane (SMPU) nanofibers and systematically investigated the morphological, thermal and mechanical properties, surface wettability, and the shape memory effect (SME) followed by the proposed programming model. The results show that GO can be well dispersed within the SMPU matrix, and the introduction of GO significantly improves the mechanical strength, surface wettability, and thermal stability of the SMPU. Compared with pristine SMPU nanofibrous mats, the prepared SMPU/GO nanofibrous mats have better SME and lower thermal shrinkage. When the loading amount of GO increased to 4.0 wt%, the thermal shrinkage ratio (R_ts) of composite nanofibrous mats could be as low as 4.7 ± 0.3%, while the average fixation ratio (R_f) and recovery ratio (R_r) could be as high as 92.1% and 96.5%, respectively. The study indicates that GO is a desirable reinforcing filler for preparing shape memory nanofibers with improved properties.     

Mechanical properties of epoxy composites filled with silane-functionalized graphene oxide

In this work, the effects of as-produced GO and silane functionalized GO (silane-f-GO) loading and silane functionalization on the mechanical properties of epoxy composites are investigated and compared. Such silane functionalization containing epoxy ended-groups is found to effectively improve the compatibility between the silane-f-GO and the epoxy matrix. Increased storage modulus, glass transition temperature, thermal stability, tensile and flexural properties and fracture toughness of epoxy composites filled with the silane-f-GO sheets are observed compared with those of the neat epoxy and GO/epoxy composites. These findings confirm the improved dispersion and interfacial interaction in the composites arising from covalent bonds between the silane-f-GO and the epoxy matrix. Moreover, several possible fracture mechanisms, i.e. crack pinning/deflection, crack bridging, and matrix plastic deformation initiated by the debonding/delamination of GO sheets, were identified and evaluated.     

High performance polyimide composite films prepared by homogeneity reinforcement of electrospun nanofibers

Highly aligned polyimide (PI) and PI nanocomposite fibers containing carbon nanotubes (CNTs) were produced by electrospinning. Scanning electron microscopy showed the electrospun nanofibers were uniform and almost free of defects. Transmission electron microscopy indicated that the CNTs were finely dispersed and highly oriented along the CNT/PI nanofiber axis at a relatively low concentration. The as-prepared well-aligned electrospun nanofibers were then directly used as homogeneity reinforcement to enhance the tensile strength and toughness of PI films. The neat PI nanofiber reinforced PI films showed good transparency, decreased bulk density and significantly improved mechanical properties. Compared with neat PI film prepared by solution casting, the tensile strength and elongation at break for the PI film reinforced with 2 wt.% CNT/PI nanofibers were remarkably increased by 138% and 104%, respectively. The significant increases in the overall mechanical properties of the nanofibers reinforced polyimide films can be ascribed to good compatibility between the electrospun nanofibers and the matrix as well as high nanofiber orientation in the matrix. Our study demonstrates a good example for fabricating high performance and high toughness polyimide nanocomposites by using this facile homogeneity self-reinforcement method.