Surface and interface electronic properties of AlGaN(0001) epitaxial layers

AlGaN layers with Al content varying over the whole range of compositions were grown by molecular beam epitaxy (MBE) on n-6H-SiC substrates. The band gap energy is obtained from the vanishing of Fabry–Pérot oscillations in a fit to optical reflection spectra near the band gap absorption edge. The surface potential was determined by in-situ X-ray photoemission spectroscopy (XPS) and is found to increase as a function of the Al content from (0.5±0.1) eV to (1.3±0.1) eV, from GaN to AlN. A Si₃N₄ thin passivation layer was formed in-situ onto a 2DEG AlGaN/GaN structure. The mechanism underlying the passivation of high electron mobility transistor (HEMT) structures is suggested to be based on the formation of interface states, which keep the Fermi level fixed at a position close to that of the free AlGaN surface. PACS 73.20.-r; 73.40.-c; 73.40.Kp     

Investigation of AlInN HEMT structures with different AlGaN buffer layers grown on sapphire substrates by MOCVD

We investigate the structural and electrical properties of Al_xIn_1–xN/AlN/GaN heterostructures with AlGaN buffers grown by MOCVD, which can be used as an alternative to AlInN HEMT structures with GaN buffer. The effects of the GaN channel thickness and the addition of a content graded AlGaN layer to the structural and electrical characteristics were studied through variable temperature Hall effect measurements, high resolution XRD, and AFM measurements. Enhancement in electron mobility was observed in two of the suggested Al_xIn_1?xN/AlN/GaN/Al_0.04Ga_0.96N heterostructures when compared to the standard Al_xIn_1–xN/AlN/GaN heterostructure. This improvement was attributed to better electron confinement in the channel due to electric field arising from piezoelectric polarization charge at the Al_0.04Ga_0.96N/GaN heterointerface and by the conduction band discontinuity formed at the same interface. If the growth conditions and design parameters of the Al_xIn_1?xN HEMT structures with AlGaN buffers can be modified further, the electron spillover from the GaN channel can be significantly limited and even higher electron mobilities, which result in lower two-dimensional sheet resistances, would be possible.     

Effects of the strain relaxation of an AlGaN barrier layer induced by various cap layers on the transport properties in AlGaN/GaN heterostructures

The strain relaxation of an AlGaN barrier layer may be influenced by a thin cap layer above, and affects the transport properties of AlGaN/GaN heterostructures. Compared with the slight strain relaxation found in AlGaN barrier layer without cap layer, it is found that a thin cap layer can induce considerable changes of strain state in the AlGaN barrier layer. The degree of relaxation of the AlGaN layer significantly influences the transport properties of the two-dimensional electron gas (2DEG) in AlGaN/GaN heterostructures. It is observed that electron mobility decreases with the increasing degree of relaxation of the AlGaN barrier, which is believed to be the main cause of the deterioration of crystalline quality and morphology on the AlGaN/GaN interface. On the other hand, both GaN and AlN cap layers lead to a decrease in 2DEG density. The reduction of 2DEG caused by the GaN cap layer may be attributed to the additional negative polarization charges formed at the interface between GaN and AlGaN, while the reduction of the piezoelectric effect in the AlGaN layer results in the decrease of 2DEG density in the case of AlN cap layer.     

High power photoconductive switches of 4H SiC with Si3N4 passivation and n -GaN subcontact

The effect of a Si₃N₄ passivation layer on the breakdown voltage in 4H SiC high power photoconductive semiconductor switching devices has been investigated. An n⁺-GaN epitaxial layer was also used for these devices as a subcontact layer, which was between the contact metal and the high resistivity SiC bulk, to improve the ohmic contact and mitigate current spreading: the GaN subcontact layer protects the contact from damage occurring at high power levels. The Si₃N₄ passivation layer was grown by ultrahigh vacuum plasma enhanced chemical vapor deposition. By using the Si₃N₄ passivation, the dark leakage current of the devices was suppressed effectively and decreased by one order of magnitude, and the breakdown voltage of the switching devices was improved significantly from 2.9 to 5 kV without degrading the high photocurrent.     

Properties of Si-doped GaN and AlGaN/GaN heterostructures grown by RF-MBE on high resistivity Fe-doped GaN

Silicon-doped GaN epilayers and AlGaN/GaN heterostructures were developed by nitrogen plasma-assisted molecular beam epitaxy on high resistivity iron-doped GaN (0001) templates and their properties were investigated by atomic force microscopy, x-ray diffraction and Hall effect measurements. In the case of high electron mobility transistors heterostructures, the AlN mole fraction and the thickness of the AlGaN barrier employed were in the range of from 0.17 to 0.36 and from 7.5 to 30 nm, respectively. All structures were capped with a 2 nm GaN layer.Despite the absence of Ga droplets formation on the surface, growth of both GaN and AlGaN by RF-MBE on the GaN (0001) surfaces followed a step-flow growth mode resulting in low surface roughness and very abrupt heterointerfaces, as revealed by XRD. Reciprocal space maps around the reciprocal space point reveal that the AlGaN barriers are fully coherent with the GaN layer.GaN layers, n-doped with silicon in the range from 10¹⁵ to 10¹⁹ cm⁻³ exhibited state of the art electrical properties, consistent with a low unintentional background doping level and low compensation ratio. The carrier concentration versus silicon cell temperatures followed an Arhenius behaviour in the whole investigated doping range. The degenerate 2DEG, at the AlGaN/GaN heteroiterfaces, exhibited high Hall mobilities reaching 1860 cm²/V s at 300 K and 10 220 cm²/V s at 77 K for a sheet carrier density of 9.6E12 cm⁻².The two dimensional degenerate electron gas concentration in the GaN capped AlGaN/GaN structures was also calculated by self-consistent solving the Schrödinger–Poisson equations. Comparison with the experimental measured values reveals a Fermi level pinning of the GaN (0001) surface at about 0.8 eV below the GaN conduction band.     

Si3N4在h-AlN上的晶体化与AlN/Si3N4纳米多层膜的超硬效应

采用反应磁控溅射法制备了一系列具有不同Si₃N₄层厚度的AlN/Si₃N₄纳米多层膜,利用X射线衍射仪、高分辨透射电子显微镜和微力学探针表征了多层膜的微结构和力学性能.研究了Si₃N₄层在AlN/Si₃N₄纳米多层膜中的晶化现象及其对多层膜生长结构与力学性能的影响.结果表明,在六方纤锌矿结构的晶体AlN调制层的模板作用下,通常溅射条件下以非晶态存在的Si₃N₄层在其厚度小于约1nm时被强制晶化为结构与AlN相同的赝形晶体,AlN/Si₃N₄纳米多层膜形成共格外延生长的结构,相应地,多层膜产生硬度升高的超硬效应.Si₃N₄随层厚的进一步增加又转变为非晶态,多层膜的共格生长结构因而受到破坏,其硬度也随之降低.分析认为,AlN/Si₃N₄纳米多层膜超硬效应的产生与多层膜共格外延生长所形成的拉压交变应力场导致的两调制层模量差的增大有关. 关键词： 3N₄纳米多层膜')" href="#">AlN/Si₃N₄纳米多层膜 外延生长 赝晶体 超硬效应     

Effects of GaN cap layer thickness on an AlN/GaN heterostructure

In this study, we investigate the effects of GaN cap layer thickness on the two-dimensional electron gas (2DEG) electron density and 2DEG electron mobility of AlN/GaN heterostructures by using the temperature-dependent Hall measurement and theoretical fitting method. The results of our analysis clearly indicate that the GaN cap layer thickness of an AlN/GaN heterostructure has influences on the 2DEG electron density and the electron mobility. For the AlN/GaN heterostructures with a 3-nm AlN barrier layer, the optimized thickness of the GaN cap layer is around 4 nm and the strained a-axis lattice constant of the AlN barrier layer is less than that of GaN.     

AlN/Si3N4纳米多层膜的外延生长与力学性能

采用射频磁控溅射方法制备单层AlN, Si₃N₄薄膜和不同调制周期的AlN/Si₃N₄纳米多层膜.采用X射线衍射仪、高分辨透射电子显微镜和纳米压痕仪对薄膜进行表征.结果发现,多层膜中Si₃N₄层的晶体结构和多层膜的硬度依赖于Si₃N₄层的厚度.当AlN层厚度为4.0nm、 Si₃N₄层厚度 关键词： 3N₄纳米多层膜')" href="#">AlN/Si₃N₄纳米多层膜 外延生长 应力场 超硬效应     

AlGaN/AlN/GaN结构中二维电子气的输运特性

对使用金属有机物汽相沉积法生长的AlGaN/AlN/GaN结构进行的变温霍尔测量，测量结果指出在AlN/GaN界面处有二维电子气存在且迁移率和浓度在2K时分别达到了1.4×10⁴cm²·V^-1·s^-1和9.3×10¹²cm^-2，且在200K到2K范围内二维电子气的浓度基本不变，变磁场霍尔测量发现只有一种载流子(电子)参与导电.在2K温度下，观察到量子霍尔效应，Shubnikov-de Haas (SdH) 振荡在磁场约为3T时出现，证明了此结构呈现了典型的二维电子气行为.通过实验数据对二维电子气散射过程的半定量分析，推出量子散射时间为0.23ps，比以往报道的AlGaN/GaN结构中的散射时间长，说明引入AlN层可以有效减小合金散射，进一步的推断分析发现低温下以小角度散射占主导地位.     

Comparison of electrical characteristic between AlN/GaN and AlGaN/GaN heterostructure Schottky diodes

Ni/Au Schottky contacts on AlN/GaN and AlGaN/GaN heterostructures are fabricated.Based on the measured current–voltage and capacitance–voltage curves,the electrical characteristics of AlN/GaN Schottky diode,such as Schottky barrier height,turn-on voltage,reverse breakdown voltage,ideal factor,and the current-transport mechanism,are analyzed and then compared with those of an AlGaN/GaN diode by self-consistently solving Schrdinger’s and Poisson’s equations.It is found that the dislocation-governed tunneling is dominant for both AlN/GaN and AlGaN/GaN Schottky diodes.However,more dislocation defects and a thinner barrier layer for AlN/GaN heterostructure results in a larger tunneling probability,and causes a larger leakage current and lower reverse breakdown voltage,even though the Schottky barrier height of AlN/GaN Schottky diode is calculated to be higher that of an AlGaN/GaN diode.     

High-electric-field-stress-induced degradation of SiN passivated AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) are fabricated by employing SiN passivation, this paper investigates the degradation due to the high-electric-field stress. After the stress, a recoverable degradation has been found, consisting of the decrease of saturation drain current I_Dsat, maximal transconductance g_m, and the positive shift of threshold voltage V_TH at high drain-source voltage V_DS. The high-electric-field stress degrades the electric characteristics of AlGaN/GaN HEMTs because the high field increases the electron trapping at the surface and in AlGaN barrier layer. The SiN passivation of AlGaN/GaN HEMTs decreases the surface trapping and 2DEG depletion a little during the high-electric-field stress. After the hot carrier stress with V_DS=20 V and V_GS=0 V applied to the device for 10⁴ sec, the SiN passivation decreases the stress-induced degradation of I_Dsat from 36% to 30%. Both on-state and pulse-state stresses produce comparative decrease of I_Dsat, which shows that although the passivation is effective in suppressing electron trapping in surface states, it does not protect the device from high-electric-field degradation in nature. So passivation in conjunction with other technological solutions like cap layer, prepassivation surface treatments, or field-plate gate to weaken high-electric-field degradation should be adopted.     

The effect of SixNy interlayer on the quality of GaN epitaxial layers grown on Si(1 1 1) substrates by MOCVD

In the present paper, the effects of nitridation on the quality of GaN epitaxial films grown on Si(1 1 1) substrates by metal–organic chemical vapor phase deposition (MOCVD) are discussed. A series of GaN layers were grown on Si(1 1 1) under various conditions and characterized by Nomarski microscopy (NM), atomic force microscopy (AFM), high resolution X-ray diffraction (HRXRD), and room temperature (RT) photoluminescence (PL) measurements. Firstly, we optimized LT-AlN/HT-AlN/Si(1 1 1) templates and graded AlGaN intermediate layers thicknesses. In order to prevent stress relaxation, step-graded AlGaN layers were introduced along with a crack-free GaN layer of thickness exceeding 2.2 μm. Secondly, the effect of in situ substrate nitridation and the insertion of an Si_xN_y intermediate layer on the GaN crystalline quality was investigated. Our measurements show that the nitridation position greatly influences the surface morphology and PL and XRD spectra of GaN grown atop the Si_xN_y layer. The X-ray diffraction and PL measurements results confirmed that the single-crystalline wurtzite GaN was successfully grown in samples A (without Si_xN_y layer) and B (with Si_xN_y layer on Si(1 1 1)). The resulting GaN film surfaces were flat, mirror-like, and crack-free. The full-width-at-half maximum (FWHM) of the X-ray rocking curve for (0 0 0 2) diffraction from the GaN epilayer of the sample B in ω-scan was 492 arcsec. The PL spectrum at room temperature showed that the GaN epilayer had a light emission at a wavelength of 365 nm with a FWHM of 6.6 nm (33.2 meV). In sample B, the insertion of a Si_xN_y intermediate layer significantly improved the optical and structural properties. In sample C (with Si_xN_y layer on Al_0.11Ga_0.89N interlayer). The in situ depositing of the, however, we did not obtain any improvements in the optical or structural properties.     

Different influences of Schottky metal on the strain and relative permittivity of barrier layer between AlN/GaN and AlGaN/GaN heterostructure Schottky diodes

Ni/Au Schottky contacts on AlN/GaN and AlGaN/GaN heterostructures are fabricated.Based on the measured current–voltage and capacitance-voltage curves,the polarization sheet charge density and relative permittivity are analyzed and calculated by self-consistently solving Schrdinger’s and Poisson’s equations.It is found that the values of relative permittivity and polarization sheet charge density of AlN/GaN diode are both much smaller than the ones of AlGaN/GaN diode,and also much lower than the theoretical values.Moreover,by fitting the measured forward I–V curves,the extracted dislocations existing in the barrier layer of the AlN/GaN diode are found to be much more than those of the AlGaN/GaN diode.As a result,the conclusion can be made that compared with AlGaN/GaN diode the Schottky metal has an enhanced influence on the strain of the extremely thinner AlN barrier layer,which is attributed to the more dislocations.     

A study on Al2O3 passivation in GaN MOS-HEMT by pulsed stress

This paper studies systematically the drain current collapse in AlGaN/GaN metal-oxide-semiconductor high electron mobility transistors （MOS-HEMTs） by applying pulsed stress to the device. Low-temperature layer of Al2O3 ultrathin film used as both gate dielectric and surface passivation layer was deposited by atomic layer deposition （ALD）. For HEMT, gate turn-on pulses induced large current collapse. However, for MOS-HEMT, no significant current collapse was found in the gate turn-on pulsing mode with different pulse widths, indicating the good passivation effect of ALD Al2O3. A small increase in Id in the drain pulsing mode is due to the relieving of self-heating effect. The comparison of synchronously dynamic pulsed Id - Vds characteristics of HEMT and MOS-HEMT further demonstrated the good passivation effect of ALD Al2O3.     

Strain modification of AlGaN layers using swift heavy ions

Epitaxial AlGaN/GaN layers grown by molecular beam epitaxy (MBE) on SiC substrates were irradiated with 150 MeV Ag ions at a fluence of 5×10¹² ions/cm². The samples used in this study are 50 nm Al_0.2Ga_0.8N/1 nm AlN/1 μ m GaN/0.1 μ m AlN grown on SI 4H-SiC. Rutherford backscattering spectrometry/channeling strain measurements were carried out on off-normal axis of irradiated and unirradiated samples. In an as-grown sample, AlGaN layer is partially relaxed with a small tensile strain. After irradiation, this strain increases by 0.22% in AlGaN layer. Incident ion energy dependence of dechanneling parameter shows E ^1/2 dependence, which corresponds to the dislocations. Defect densities were calculated from the E ^1/2 graph. As a result of irradiation, the defect density increased on both GaN and AlGaN layers. The effect of irradiation induced-damages are analyzed as a function of material properties. Observed results from different characterization techniques such as RBS/channeling, high-resolution XRD and AFM are compared and complemented with each other to deduce the information. Possible mechanisms responsible for the observations have been discussed in detail.     

Two-dimensional electron gas densities in AlGaN/AlN/GaN heterostructures

The dependence of two-dimensional electron gas (2DEG) density and distribution in an Al_xGa_1-xN/AlN/GaN heterostructure on the thicknesses of the Al_xGa_1-xN barrier layer and the AlN interfacial layer are investigated theoretically. A competitive contribution of the AlGaN and AlN layers to the 2DEG density is revealed. For an AlN interfacial layer thinner than a critical value d_cAlN, the 2DEG density is dominated by the AlGaN barrier and the 2DEG density increases with the increase of the AlGaN barrier thickness, as in the case of a simple AlGaN/GaN heterostructure. While the AlN interfacial layer will take the dominant contribution to the 2DEG density as its thickness exceeds d_cAlN. In this case, the increase of AlGaN barrier layer thickness leads to the decrease of the 2DEG density. Detailed calculations show that the critical AlN thickness increases with the increase of Al content in the AlGaN barrier. PACS 85.30.De; 73.40.Kp; 02.60.Cb     

Influence of thermal stress on the relative permittivity of the AlGaN barrier layer in an AlGaN/GaN heterostructure Schottky contacts

Ni Schottky contacts on AlGaN/GaN heterostructures were fabricated. Some samples were thermally treated in a furnace with N₂ ambience at 600 °C for different times (0.5 h, 4.5 h, 10.5 h, 18 h, 33 h, 48 h, and 72 h), the others were thermally treated for 0.5 h at different temperatures (500 °C, 600 °C, 700 °C, and 800 °C). With the measured current—voltage (I—V) and capacitance—voltage (C—V) curves and by self-consistently solving Schrodinger's and Poisson's equations, we found that the relative permittivity of the AlGaN barrier layer was related to the piezoelectric and the spontaneous polarization of the AlGaN barrier layer. The relative permittivity was in proportion to the strain of the AlGaN barrier layer. The relative permittivity and the strain reduced with the increased thermal stress time until the AlGaN barrier totally relaxed (after 18 h at 600 °C in the current study), and then the relative permittivity was almost a constant with the increased thermal stress time. When the sample was treated at 800 °C for 0.5 h, the relative permittivity was less than the constant due to the huge diffusion of the contact metal atoms. Considering the relation between the relative permittivity of the AlGaN barrier layer and the converse piezoelectric effect, the conclusion can be made that a moderate thermal stress can restrain the converse piezoelectric effect and can improve the stability of AlGaN/GaN heterostructure devices.     

AlGaN/GaN-based HEMT on SiC substrate for microwave characteristics using different passivation layers

In this paper, a new gate-recessed AlGaN/GaN-based high electron mobility transistor (HEMT) on SiC substrate is proposed and its DC as well as microwave characteristics are discussed for Si₃N₄ and SiO₂ passivation layers using technology computer aided design (TCAD). The two-dimensional electron gas (2DEG) transport properties are discussed by solving Schr?dinger and Poisson equations self-consistently resulting in various subbands having electron eigenvalues. From DC characteristics, the saturation drain currents are measured to be 600?mA/mm and 550?mA/mm for Si₃N₄ and SiO₂ passivation layers respectively. Apart from DC, small-signal AC analysis has been done using two-port network for various microwave parameters. The extrinsic transconductance parameters are measured to be 131.7?mS/mm at a gate voltage of V _gs?= ?0.35?V and 114.6?mS/mm at a gate voltage of V _gs?= ?0.4?V for Si₃N₄ and SiO₂ passivation layers respectively. The current gain cut-off frequencies (f _t) are measured to be 27.1?GHz and 23.97?GHz in unit-gain-point method at a gate voltage of ?0.4?V for Si₃N₄ and SiO₂ passivation layers respectively. Similarly, the power gain cut-off frequencies (f _max) are measured to be 41?GHz and 38.5?GHz in unit-gain-point method at a gate voltage of ?0.1?V for Si₃N₄ and SiO₂ passivation layers respectively. Furthermore, the maximum frequency of oscillation or unit power gain (MUG = 1) cut-off frequencies for Si₃N₄ and SiO₂ passivation layers are measured to be 32?GHz and 28?GHz respectively from MUG curves and the unit current gain, ?O?h ₂₁??O?=?1 cut-off frequencies are measured to be 140?GHz and 75?GHz for Si₃N₄ and SiO₂ passivation layers respectively from the abs ?O?h ₂₁??O curves. HEMT with Si₃N₄ passivation layer gives better results than HEMT with SiO₂ passivation layer.     

Determination of the series resistance under the Schottky contacts of AlGaN/AlN/GaN Schottky barrier diodes

Rectangular AlGaN/AlN/GaN heterostructure field-effect transistors (HFETs) were fabricated, and the gate and the source of the HFETs consisted of AlGaN/AlN/GaN Schottky barrier diodes (SBDs). Based on the measured forward current-voltage and the capacitance-voltage characteristics of the AlGaN/AlN/GaN SBDs, the series resistance under the Schottky contacts (R_S) was calculated using the method of power consumption, which has been proved to be valid. Finally, the method of power consumption for calculating R_S was successfully used to study the two-dimensional electron gas electron mobility for a series of circular AlGaN/AlN/GaN SBDs. It is shown that the series resistance under the Schottky contacts cannot be neglected and is important for analysing and characterizing the AlGaN/AlN/GaN SBDs and the AlGaN/AlN/GaN HFETs.     

Degradation mechanism of two-dimensional electron gas density in high Al-content AlGaN/GaN heterostructures

This paper finds that the two-dimensional electron gas density in high Al-content AlGaN/GaN heterostructures exhibits an obvious time-dependent degradation after the epitaxial growth. The degradation mechanism was investigated in depth using Hall effect measurements, high resolution x-ray diffraction, scanning electron microscopy, x-ray photoelectron spectroscopy and energy dispersive x-ray spectroscopy. The results reveal that the formation of surface oxide is the main reason for the degradation, and the surface oxidation always occurs within the surface hexagonal defects for high Al-content AlGaN/GaN heterostructures.