Preparation of carbon nanosheets deposited on carbon nanotubes by microwave plasma-enhanced chemical vapor deposition method

Carbon nanosheets were synthesized by microwave plasma-enhanced chemical vapor deposition method on carbon nanotubes substrate which was treated by hydrogen plasma. The results showed that the diameters of carbon nanotubes first got thick and then “petal-like” carbon nanosheets were grown on the outer wall of carbon nanotubes. The diameters of carbon nanotubes without and with carbon nanosheets were 100-150 and 300-500 nm, respectively. Raman spectrum indicated the graphite structure of carbon nanotubes/carbon nanosheets. The hydrogen plasma treatment and reaction time greatly affected the growth and density of carbon nanosheets. Based on above results, carbon nanosheets/carbon nanotubes probably have important applications as cold cathode materials and electrode materials.     

Influence of TaCl5 partial pressure on texture structure of TaC coating deposited by chemical vapor deposition

TaC was deposited on graphite substrate with different TaCl₅ partial pressure at 800 °C and 1200 °C by chemical vapor deposition. Microstructures and texture structures of the prepared coatings were researched with X-ray diffraction and scanning electronic microscopy. When the coating deposition process is controlled by surface reaction kinetics (800 °C), TaCl₅ partial pressure had little influence on the microstructure and texture structure of the coating. When the coating formation process is controlled by diffusion kinetics (1200 °C), the microstructure, texture structure of the prepared TaC grains vary greatly with TaCl₅ partial pressure. In the diffusion controlled process, the increasing of TaCl₅ partial pressure will result in the changing of gas supersaturation, and then the occurrence of secondary nucleation, which is the main reason for the changing of coating morphology and texture structure. With the help of competitive growth in (1 0 0) and (1 1 1) directions, the formation mechanism of the different texture coatings are discussed in detail. In addition, a diffusion model of deposition species around step-edge-corner was also proposed to explain the growth mechanism of the texture coatings.     

纳米TiO2薄膜的低温等离子体制备技术

以四氯化钛为源物质,氩气为载气,氧气为反应气体,利用低温等离子体增强化学气相沉积在硅基表面制备出了TiO2薄膜。使用场发射扫描电子显微镜、X射线衍射仪等检测分析表征TiO2薄膜的性能与性质,并探讨了工艺条件如基片材料、沉积时间和基片温度对薄膜性能的影响。结果表明：制备的薄膜表面光滑均匀,结构致密,最小晶粒尺寸约15 nm;薄膜的晶型主要依赖于沉积温度,低于300 ℃沉积的薄膜是无定形的,300 ℃之上沉积的薄膜是锐钛矿结构。     

Nanomechanical characteristics of SnO2:F thin films deposited by chemical vapor deposition

The nanoindentation characterizations and mechanical properties of fluorine-doped tin oxide (SnO₂:F) films deposited on glass substrates, using chemical vapor deposition (CVD) method, were studied, which included the effects of the indentation loads, the loading time and the hold time on the thin film. The surface roughness, fractal dimension and frictional coefficient were also studied by varying the freon flow rates. X-ray diffraction (XRD), atomic force microscopy (AFM) and frictional force microscopy (FFM) were used to analyze the morphology of the microstructure. The results showed that crystalline structure of the film had a high intensity (1 1 0) peak orientation, especially at a low freon flow rate. According to the nanoindentation records, the Young's modulus ranged from 62.4 to 75.1 GPa and the hardness ranged from 5.1 to 9.9 GPa at a freon flow rate of 8000 sccm. The changes in measured properties were due to changing loading rate.     

Preparation and characterization of boron nitride coatings on carbon fibers from borazine by chemical vapor deposition

Boron nitride (BN) coatings were deposited on carbon fibers by chemical vapor deposition (CVD) using borazine as single source precursor. The deposited coatings were characterized by scanning electron microscopy (SEM), Auger electron spectroscopy (AES), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy. The effect of temperatures on growth kinetics, morphology, composition and structure of the coatings was investigated. In the low temperature range of 900 °C-1000 °C, the growth rate increased with increasing temperature complying with Arrhenius law, and an apparent active energy of 72 kJ/mol was calculated. The coating surface was smooth and compact, and the coatings uniformly deposited on individual fibers of carbon fiber bundles. The growth was controlled by surface reaction. At 1000 °C, the deposition rate reached a maximum (2.5 μm/h). At the same time, the limiting step of the growth translated to be mass-transportation. Above 1100 °C, the growth rate decreased drastically due to the occurrence of gas-phase nucleation. Moreover, the coating surface became loose and rough. Composition and structure examinations revealed that stoichiometric BN coatings with turbostratic structure were obtained below 1000 °C, while hexagonal BN coatings were deposited above 1100 °C. A penetration of carbon element from the fibers to the coatings was observed.     

等离子体增强脉冲激光沉积o-BN薄膜

利用等离子体增强脉冲激光沉积系统在Si（100）基底上沉积出了高质量的o-BN薄膜,利用红外光谱（FTIR）、X射线衍射谱（XRD）和原子力显微镜照片对o-BN薄膜进行了表征.通过红外光谱（FTIR）得到o-BN薄膜的红外峰特征峰值为1189cm^-1,1585cm^-1和1450cm^-1;由XRD谱得到o-BN薄膜的（111）,（020）,（021）,（310）和（243）各晶面的衍射峰, 特别是（310）和（243）晶面的衍射峰非常强;通过原子力显微镜照片清楚看到BN薄膜具有尖状突起的表面形貌. 关键词： 等离子体增强脉冲激光沉积 氮化硼薄膜 X射线衍射谱     

Effect of freon flow rate on tin oxide thin films deposited by chemical vapor deposition

High quality fluorine-doped tin oxide (SnO₂:F) films on glass substrates were been prepared using chemical vapor deposition (CVD) method. The electrical properties, surface morphologies, structural properties and optical properties of the films were studied by varying the freon flow rates. The structure was analyzed by X-ray diffraction (XRD). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to study the morphology. Energy-dispersive spectroscopy (EDS) was conducted to understand the surface fluorine composition of the film. The results showed that crystalline structure of the film had a have cassiterite-like diffraction patterns with a preferred orientation of (1 1 0). Surface roughness was evaluated by atomic force microscopy, characterized by root mean square (RMS) and average value (Ra). The SnO₂:F resistivity decreased as the freon flow rate increased. The films had a uniform thickness and a transmittance of 80–90% within the visible region of the spectrum.     

等离子体增强热丝CVD生长碳纳米尖端的研究

用CH₄，NH₃和H₂为反应气体，利用等离子体增强热丝化学气相沉积系统在不同偏压电流的条件下制备了碳纳米尖端，并用扫描电子显微镜和显微Raman光谱仪对碳纳米尖端进行了研究.结果表明碳纳米尖端是石墨结构，随着偏压电流的增大，碳纳米尖端的顶角减小，生长速率增大.结合有关等离子体和溅射的理论，分析讨论了碳纳米尖端的形成和碳纳米尖端的生长随偏压电流的变化. 关键词： 碳纳米尖端 等离子体 化学气相沉积     

Composite SiO2/TiO2 and amine polymer/TiO2 nanoparticles produced using plasma-enhanced chemical vapor deposition

Plasma-enhanced chemical vapor deposition was used to conformally coat commercial TiO₂ nanoparticles to create nanocomposite materials. Hexamethyldisiloxane (HMDSO)/O₂ plasmas were used to deposit SiO₂ or SiO_xC_yH_z films, depending on the oxidant concentration; and hexylamine (HexAm) plasmas were used to deposit amorphous amine-containing polymeric films on the TiO₂ nanoparticles. The composite materials were analyzed using Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). These analyses reveal film composition on the nanoparticles was virtually identical to that deposited on flat substrates and that the films deposit a conformal coating on the nanoparticles. The performance of the nanocomposite materials was evaluated using UV-vis spectroscopy to determine the dispersion characteristics of both SiO_x and HexAm coated TiO₂ materials. Notably, the coated materials stay suspended longer in distilled water than the uncoated materials for all deposited films.     

Effects of annealing treatment on the formation of CO2 in ZnO thin films grown by metal-organic chemical vapor deposition

Post-growth annealing was carried out on ZnO thin films grown by metal-organic chemical vapor deposition (MOCVD). The grain size of ZnO thin film increases monotonically with annealing temperature. The ZnO thin films were preferential to c-axis oriented after annealing as confirmed by X-ray diffraction (XRD) measurements. Fourier transformation infrared transmission measurements showed that ZnO films grown at low temperature contains CO₂ molecules after post-growth annealing. A two-step reaction process has been proposed to explain the formation mechanism of CO₂, which indicates the possible chemical reaction processes during the metal-organic chemical vapor deposition of ZnO films.     

等离子体增强化学气相沉积法实现硅纳米线掺硼

用等离子体增强化学气相沉积(PECVD)方法成功实现硅纳米线的掺B.选用Si片作衬底，硅烷 （SiH4）作硅源，硼烷（B2H6）作掺杂气体， Au作催化剂，生长温度440℃.基于气-液-固(VLS)机制，探讨了掺B硅纳米线可能的生长机制.PECVD法化学成分配比更灵活，更容易实现纳米线掺杂，进一步有望生长硅纳米线pn结，为研制纳米量级器件提供技术基础. 关键词： 硅纳米线 化学气相沉积 纳米器件     

A chemical kinetic model for chemical vapor deposition of carbon nanotubes

Carbon nanotubes (CNTs) are classified among the most promising novel materials due to their exceptional physical properties. Still, optimal fabrication of carbon nanotubes involves a number of challenges. Whatever be the fabrication method, a process optimization can be evolved only on the basis of a good theoretical model to predict the parametric influences on the final product. The work reported here investigates the dependence of the deposition parameters on the controllable parameters for carbon nanotube growth during Chemical vapor deposition (CVD), through a chemical kinetic model. The theoretical model consisted of the design equations and the energy balance equations, based on the reaction kinetics, for the plug flow and the batch reactor, which simulate the CVD system. The numerical simulation code was developed in-house in a g++ environment. The results predicted the growth conditions for CNT: the deposition temperature, pressure and number of atoms, which were found to be influenced substantially by the initial controllable parameters namely the temperature, volumetric flow rate of the carbon precursor, and the reaction time. An experimental study was also conducted on a CVD system developed in the laboratory, to benchmark the computational results. The experimental results were found to agree well with the theoretical predictions obtained from the model.     

Deposition of thin rhodium films by plasma-enhanced chemical vapor deposition

Thin films of rhodium have been prepared starting from dicarbonyl-2.4-pentadionato-rhodium(I), Rh(CO)₂C₅H₇O₂, by plasma enhanced CVD. The dependence of the deposition rate and film properties on substrate temperature, partial pressure of the organometallic and on hydrogen has been studied. Metal contents of 100% and thin-film resistivities as low as 5 times the bulk resistivity of rhodium have been achieved.     

纳米TiO_2薄膜的低温等离子体制备技术

以四氯化钛为源物质,氩气为载气,氧气为反应气体,利用低温等离子体增强化学气相沉积在硅基表面制备出了TiO2薄膜。使用场发射扫描电子显微镜、X射线衍射仪等检测分析表征TiO2薄膜的性能与性质,并探讨了工艺条件如基片材料、沉积时间和基片温度对薄膜性能的影响。结果表明:制备的薄膜表面光滑均匀,结构致密,最小晶粒尺寸约15 nm;薄膜的晶型主要依赖于沉积温度,低于300℃沉积的薄膜是无定形的,300℃之上沉积的薄膜是锐钛矿结构。     

立方氮化硼薄膜生长过程中的界面控制

在立方氮化硼薄膜气相生长过程中生成的无定形初期层和乱层结构氮化硼中间层，一直是阻碍立方氮化硼薄膜外延生长的主要原因.系统地分析了硅衬底预处理对立方氮化硼薄膜中无定形初期层成分的影响，发现在等离子体化学气相生长法制备薄膜时，硅衬底上形成无定形初期层的可能原因有氧的存在、离子轰击以及高温下硅的氮化物的形成.在H₂气氛中1200K热处理硅衬底可以有效地减少真空室中残留氧浓度，除去硅表面的自然氧化层，保持硅衬底表面晶体结构.控制衬底温度不超过900 K，就能防止硅的氮化物的形成，成功地除去无 关键词： 立方氮化硼薄膜 等离子体化学气相生长 界面 电子显微镜     

Controllable growth of individual, uniform carbon nanotubes by thermal chemical vapor deposition

We report on the controllable growth of individual, uniform carbon nanotubes using thermal chemical vapor deposition (CVD). We performed a detailed study of the various factors influencing the growth of single nanotubes. In particular, we investigated the role played by catalyst layer thickness, catalyst dot size, deposition temperature, and gas source pressure on the growth process of straight, single nanotubes. Straight, individual nanotubes with uniform diameter can be obtained by decomposition of 0.1 mbar of acetylene at a temperature of 800 °C over a 5 nm thick nickel film that is patterned into square dots with dimensions below 500 nm. We compare the performance of thermal CVD and of plasma enhanced CVD for growing individual nanotubes.     

线性微波化学气相沉积制备SiNx薄膜的微结构及光学性能研究

利用自主研发的线性微波化学气相沉积系统在不同微波功率、微波占空比、基片温度、特气比例条件下制备了SiN_x薄膜. 通过扫描电子显微镜、椭圆偏振仪等表征测量技术, 研究了不同工艺参数对SiN_x薄膜表面形貌、元素配比、折射率、沉积速度的影响, 并探讨了薄膜元素配比、折射率、沉积速度间的关系. 结果表明: 利用线性微波沉积技术, 不同工艺参数下制备的SiN_x薄膜组成元素分布均匀, 同时具有平整的表面状态; 特气比例和微波占空比是影响薄膜折射率的最主要因素, 薄膜折射率在1.92–2.33之间连续可调; 微波功率、微波占空比、沉积温度、特气比例都对SiN_x 薄膜沉积速度影响较大, 制备的SiN_x薄膜最大沉积速度为135 nm·min^-1.     

Preparation of nanowall Bi2S3 films by chemical bath deposition

Nanowall shaped Bi₂S₃ films were prepared by chemical bath deposition in which ammonium citrate and thioacetamide were used as chelating reagent and sulfur source, respectively. The nanowall Bi₂S₃ films show large-surface-area nanowall shaped morphology. It is found that the pH value (pH = 6 or pH = 6.5) of the solution is a crucial parameter to obtain the nanowall shaped Bi₂S₃ films. The composition of the nanowall Bi₂S₃ films is close to the stoichiometric ratio of Bi₂S₃. The absorption edge of the nanowall shaped Bi₂S₃ films is located at around 900 nm, indicating that the optical bandgap of the Bi₂S₃ films is around 1.4 eV. The nanowall Bi₂S₃ films show obvious photo-sensitivity. The photo-to-dark conductivity ratios of the nanowall Bi₂S₃ films prepared at pH = 6 and pH = 6.5 are all around 50. This value is around five times than that of the non-nanowall shaped Bi₂S₃ films which is prepared at pH = 7.     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

Synthesis and characterization of graphenated carbon nanotubes on IONPs using acetylene by chemical vapor deposition method

The graphenated carbon nanotubes (G-CNTs) were synthesized on monodisperse spherical iron oxide nanoparticles (IONPs) using acetylene as carbon precursor by simple chemical vapor deposition method. The reaction parameters such as temperature and flow of carbon source were optimized in order to achieve G-CNTs with excellent quality and quantity. Transmission electron microscopy (TEM) clearly illustrated that the graphene flakes are forming along the whole length on CNTs. The degree of graphitization was revealed by X-ray diffraction (XRD) analysis and Raman spectroscopic techniques. The intensity of D to G value was less than one which confirms the obtained G-CNTs have high degree of graphitization. The optimum reaction temperature for the IONPs to form metallic clusters which in turn lead to the formation of G-CNTs with high carbon deposition yield is at 900 °C. The TEM shows the CNTs diameter is 50 nm with foiled graphene flakes of diameter around 70 nm. Our results advocate for IONPs as a promising catalytic template for quantitative and qualitative productivity of nanohybrid G-CNTs. The produced G-CNTs with high degree of graphitization might be an ideal candidate for nanoelectronic application like super capacitors and so on.