Synthesis of fluorinated polybenzoxazoles with low dielectric constants

Two fluorinated aromatic bis(o‐aminophenol)s, 1,1‐bis(3′‐amino‐4′‐hydroxyphenyl)‐1‐(3′‐trifluoromethylphenyl)‐2,2,2‐trifluoroethane (6FAP) and 1,1‐bis(3′‐amino‐4′‐hydroxyphenyl)‐1‐(3′,5′‐ditrifluoromethylphenyl)‐2,2,2‐trifluoroethane (9FAP) were synthesized, which were allowed to polycondense with aromatic diacyl chlorides to afford the fluorinated aromatic polybenzoxazoles (PBOs) via a conventional two‐step procedure in which the low‐temperature solution polycondensation process was first performed to yield poly(o‐hydroxyamide)s (PHAs) followed by the thermal cyclodehydration to give the PBOs. Experimental results indicated that the PHAs had inherent viscosities in the range of 0.29–0.68 dL/g, showing excellent solubility in organic solvents. The PHAs could be thermally cyclodehydrated into the corresponding PBOs at 260–370 °C. The obtained PBOs exhibited enhanced glass‐transition temperature but decreased solubility with respect to the PHAs. The PBOs showed glass‐transition temperatures in the range of 315–337 °C and excellent thermal stabilities with 5% original weight‐loss temperatures (T₅) of >513 °C. Additionally, the PBO films had average refractive index of 1.5298–1.5656, birefringence of 0.0051–0.0092, and low dielectric constants of 2.57–2.70. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

The synthesis,characterization, and crystal structures of poly(2,6‐naphthalenebenzobisoxazole) and poly(1,5‐naphthalenebenzobisoxazole)

The rigid‐rod polymers, poly(2,6‐naphthalenebenzobisoxazole) (Naph‐2,6‐PBO) and poly(1,5‐naphthalenebenzobisoxazole) (Naph‐1,5‐PBO) were synthesized by high temperature polycondensation of isomeric naphthalene dicarboxylic acids with 4,6‐diaminoresorcinol dihydrochloride in polyphosphoric acid. Expectedly, these polymers were found to have high thermal as well as thermooxidative stabilities, similar to what has been reported for other polymers of this class. The chain conformations of Naph‐2,6‐PBO and Naph‐1,5‐PBO were trans and the crystal structures of Naph‐2,6‐PBO and Naph‐1,5‐PBO had the three‐dimensional order, although the axial disorder existed for both Naph‐2,6‐PBO and Naph‐1,5‐PBO. Naph‐2,6‐PBO exhibited a more pronounced axial disorder than Naph‐1,5‐PBO because of its more linear shape. The repeat unit distance for Naph‐2,6‐PBO (14.15 Å) was found to be larger compared with that of Naph‐1,5‐PBO (12.45 Å) because of the more kinked structure of the latter. The extents of staggering between the adjacent chains in the ac projection of the crystal structure were 0.25c and 0.23c for Naph‐2,6‐PBO and Naph‐1,5‐PBO, respectively. Naph‐1,5‐PBO has a more kinked and twisted chain structure relative to Naph‐2,6‐PBO. The kinked and twisted chain structure of Naph‐1,5‐PBO in the crystal seems to prevent slippage between adjacent chains in the crystal structure. The more perfect crystal structure of Naph‐1,5‐PBO may be due to this difficulty in the occurrence of the slippage. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1948–1957, 2006     

In situ polymerization and characterization of graphene oxide‐co‐poly(phenylene benzobisoxazole) copolymer fibers derived from composite inner salts

A facile and efficient strategy for preparing well dispersed graphene oxide (GO)‐co‐Poly(phenylene benzobisoxazole) (PBO) copolymer fibers was carried out by direct in situ polycondensation of composite inner salts. The composite inner salts were achieved to improve the dispersivity, solubility, reactivity, and interfacial adhesion of GO in PBO polymer matrix. The structure and morphology of GO‐co‐PBO copolymer fibers have been characterized. It was demonstrated that GO were covalently incorporated with PBO molecular chains and dispersed considerably well in PBO fiber even the GO reach to 3 wt %. Meanwhile, the tensile modulus, tensile strength and thermal stability of GO‐co‐PBO copolymer fibers increased considerably with GO. The mechanism and theoretical calculation of GO enhanced PBO fiber were also discussed. The main reasons for the improvement on performance of PBO fiber should be attributed to good dispersion GO in PBO matrix and covalent bonding networks at the interface between GO and PBO molecular chains. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of high thermal stability polybenzoxazoles via ortho‐imide‐functional benzoxazine monomers

We report our work for preparing cross‐linked polyimide via a series of imide functional benzoxazine resins as precursors. The structures of synthesized monomers have been confirmed by ¹H NMR and FT‐IR. Among this class of benzoxazine monomers, the ortho‐imide functional benzoxazine resins show useful features both in the synthesis of benzoxazine monomers and the properties of the corresponding thermosets. For the cross‐linked polyimides based on ortho‐imide functional benzoxazine, an additional route is adopted to form a more thermally stable cross‐linked polybenzoxazole with the release of carbon dioxide. The ortho‐imide functional benzoxazine resins show the possibility to form high performance and even super high performance thermosets with low cost and easy processability. The thermal properties are evaluated by DSC and TGA. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1330–1338     

Montmorillonite‐based nanocomposites of polybenzoxazole: Synthesis and characterization (I)

Poly(amic acid) was synthesized by means of low‐temperature‐solution polymerization of 3,3′‐dihydroxybenzidine and pyromellitic dianhydride in N,N‐dimethylacetamide. The precursor polymer was heat‐treated at different temperatures to create a polybenzoxazole (PBO) through a polyimide (PI). PI containing the hydroxyl group was rearranged by decarboxylation with heat treatment, resulting in a fully aromatic PBO. Hexadecylamine was used as an organophilic alkylamine in organo‐clay. We have tried to clarify the intercalation of heterocyclic polymer chains to hexadecylamine–montmorillonite (C₁₆‐MMT) and improve tensile properties. It was found that the addition of only a small amount of organo‐clay was enough to improve the mechanical properties of PBO. Maximum enhancement in the ultimate tensile strength for PBO hybrids was observed for the blends containing 4% C₁₆‐MMT. The initial modulus monotonically increased with further increases in the C₁₆‐MMT content. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 471–476, 2001     

Layer effects of photovoltaic heterojunction of fully conjugated heterocyclic aromatic rigid‐rod polymer poly‐p‐phenylenebenzobisoxazole

Poly‐p‐phenylenebenzobisoxazole (PBO) contains a fully conjugated rod‐like backbone entailing excellent optoelectronic properties and superior stabilities. Poly(2,3‐dihydrothieno‐1,4‐dioxin):polystyrenesulfonate (PEDOT:PSS) is a hole transferring medium, which was spun into a thin‐film between PBO and indium‐tin‐oxide to facilitate photovoltaic (PV) effect by forming a donor‐acceptor interlayer to separate and to transport photoinduced charges. Optimum PBO thickness for PV heterojunctions was about 71 nm at which the hole transferring PEDOT:PSS generated the maximum short circuit current (I_sc) at a thickness of 115 nm. By using a layer of lithium fluoride (LiF) as an electron transferring layer adhering to Al cathode, the most open circuit voltage (V_oc) and I_sc were achieved with a LiF thickness of 1–2 nm because of possible electric dipole effect leading to an increase of V_oc from 0.7 to 0.92 V and of I_sc from about 0.1 to 0.2 μA. No PV response was observed for all PBO homojunctions because of insufficient exciton separation into electrons and holes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 988–993, 2007     

Synthesis and properties of gradient copolymers based on 2‐phenyl‐2‐oxazoline and 2‐nonyl‐2‐oxazoline

In this study, the structure–property relationships for a series of statistical 2‐nonyl‐2‐oxazoline (NonOx) and 2‐phenyl‐2‐oxazoline (PhOx) copolymers were investigated for the first time. The copolymerization kinetics were studied and the reactivity ratios were calculated to be r_NonOx = 7.1 ± 1.4 and r_PhOx = 0.02 ± 0.1 revealing the formation of gradient copolymers. The synthesis of a systematical series of NonOx–PhOx copolymers is described, whereby the amount of NonOx was increased in steps of 10 mol %. The thermal and surface properties were investigated for this series of well‐defined copolymers. The thermal properties revealed a linear decrease in glass transition temperature for copolymers containing up to 39 wt % NonOx. Furthermore, the melting temperature of the copolymers containing 0 to 55 wt % PhOx linearly decreased most likely due to disturbance of the NonOx crystalline domains by incorporation of PhOx in the NonOx part of the copolymer. The surface energies of spincoated polymer films revealed a strong decrease in surface energy upon incorporation of NonOx in the copolymers due to strong phase separation between NonOx and PhOx allowing the NonOx chains to orient to the surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6433–6440, 2009     

Significant glass‐transition‐temperature increase through hydrogen‐bonded copolymers

The role of hydrogen bonding in promoting intermolecular cohesion and higher glass‐transition temperatures of polymer is a subject of longstanding interest. A series of poly(vinylphenol‐co‐vinylpyrrolidone) copolymers were prepared by the free‐radical copolymerization of acetoxystyrene and vinylpyrrolidone; this was followed by the selective removal of the acetyl protective group, with corresponding and significant glass‐transition‐temperature increases after this procedure. The incorporation of acetoxystyrene into poly(vinylpyrrolidone) resulted in lower glass‐transition temperatures because of the reduced dipole interactions in its homopolymers. However, the deacetylation of acetoxystyrene to transform the poly(vinylphenol‐co‐vinylpyrrolidone) copolymer enhanced the higher glass‐transition temperature because of the strong hydrogen bonding in the copolymer chain. The thermal properties and hydrogen bonding of these two copolymers were investigated with differential scanning calorimetry and Fourier transform infrared spectroscopy, and good correlations between the thermal behaviors and IR results were observed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2313–2323, 2002     

Resonance raman spectra of poly‐(p‐phenylenebenzobisoxazole), poly‐(p‐phenylenebenzobisthiazole), and poly(pyridobisimidazole)

Resonance Raman spectra of poly(p‐phenylenebenzobisoxazole) (PBO), poly(p‐phenylenebenzobisthazole) (PBZT), and poly(pyridobisimidazole) (PIPD) were measured. In the case of PBO, no large dependence on wavelength of excited laser can be observed, whereas in the cases of PBZT and PIPD, the spectra depends on wavelength of excited laser. This difference may be attributed to the colors of the samples: PBO is gold, and PBZT and PIPD are metallic blue, which show the different conjugated states. The spectra of PBO are rather simpler than those of PBZT and PIPD. This is considered to be reflected by the fact that only a chain passes through the unit cell of PBO, while two chains pass through the unit cell of PBZT and PIPD. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1791–1793, 2001     

Synthesis and characterization of novel fluorosilicone rubber using imide modified vinyl‐containing fluorosilicone resin as cross‐linker

A novel imide modified vinyl‐containing fluorosilicone resin (MP‐VFS) was firstly prepared from maleopimaric acid (MPA), and characterized by ¹H NMR and ¹³C NMR. Containing MPA based imide heterocycle (MPABI), MP‐VFS was further used as a novel cross‐linker to prepare MPA modified fluorosilicone rubber (MP‐FSR). Morphology, mechanical and oil‐resistance properties, thermal properties, and low temperature resistance of MP‐FSR had been studied. Microphase separation was observed in MP‐FSR. Although the tensile strength of fluorosilicone rubber was not significantly enhanced, the tearing strength, breaking elongation, rebound resilience and hardness were effectively improved. When the MP‐VFS content was 2.0 wt %, the tearing strength of MP‐FSR was increased by 23.5%, breaking elongation by 18.6% and rebound resilience by 9.7%. The thermal stability was enhanced due to the incorporation of MPABI. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1769–1776     

Thermal stability of porous it‐PMMA thin film obtained by the extraction of st‐PMAA from it‐PMMA/st‐PMAA stereocomplex with layer‐by‐layer assembly on a substrate

The functionality of porous isotactic (it) poly(methyl methacrylate) (PMMA) thin films, which were previously developed by the selective extraction of syndiotactic (st) poly(methacrylic acid) (PMAA) from the it‐PMMA/st‐PMAA stereocomplex thin film on a substrate using the layer‐by‐layer assembly method was investigated after thermal treatment (70, 80, and 90 °C) in water for 4 h. Quartz crystal microbalance analysis and infrared spectra measurements revealed that the st‐PMAA incorporation ability of the porous it‐PMMA thin film decreased in order at 80 and 90 °C, while there was no decrease observed at 70 °C. X‐ray diffraction analysis also supported the thermal stability of the porosity at 70 °C, whereas two it‐PMMA crystalline peaks (2θ = 9° and 14°) were generated during heating at 90 °C. The loss of the functionality of the it‐PMMA thin film was thus shown to be due to crystallization, which was caused by the increase in polymer‐chain mobility during the heating process. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3265–3270, 2010     

Chain‐growth condensation polymerization approach to synthesis of well‐defined polybenzoxazole: Importance of higher reactivity of 3‐amino‐4‐hydroxybenzoic acid ester compared to 4‐amino‐3‐hydroxybenzoic acid ester

Application of chain‐growth condensation polymerization (CGCP) to obtain well‐defined polybenzoxazole (PBO) was examined. CGCP of both phenyl 3‐{(2‐methoxyethoxy)methoxy (MEM‐oxy)}‐4‐(octylamino)benzoate ( 1b ) (para‐substituted monomer) and phenyl 4‐MEM‐oxy‐3‐(octylamino)benzoate ( 3b ) (meta‐substituted monomer) was examined in the presence of metal disilazide base and phenyl 4‐nitro‐ or methylbenzoate 2 as an initiator. Polymerization of the latter monomer, but not the former, afforded polymer with controlled molecular weight based on the feed ratio of monomer to initiator and with a narrow molecular weight distribution. Accordingly, monomer 3c , in which the octyl group on the amino nitrogen of 3b was replaced with a 4‐(octyloxy)benzyl (OOB) group, was polymerized in the presence of lithium 1,1,1,3,3,3‐hexamethyldisilazide (LiHMDS), phenyl 4‐methylbenzoate ( 2b ), and LiCl in THF at 0 °C to yield poly 3c with well‐defined molecular weight (M_n = 4520–9080) and low polydispersity (M_w/M_n ≤ 1.11). Treatment of poly 3c with trifluoroacetic acid simultaneously removed the MEM and OOB groups, affording poly(o‐hydroxyamide) (poly 4 ) without scission of the amide linkages. Cyclodehydration of poly 4 proceeded at 350 °C to yield PBO (poly 5 ), which was insoluble in organic solvents and acids. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1730–1736     

Syntheses and properties of new aromatic polybenzoxazoles bearing ether and phenylethylidene or 1‐phenyl‐2,2,2‐trifluoroethylidene linkages

Two new bis(ether acyl chloride)s, 1,1‐bis[4‐(4‐chloroformylphenoxy)phenyl]‐1‐phenylethane and 1,1‐bis[4‐(4‐chloroformylphenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane, were prepared from readily available reagents. Aromatic polybenzoxazoles with both ether and phenylethylidene or 1‐phenyl‐2,2,2‐trifluoroethylidene linkages between phenylene units were obtained by a conventional two‐step procedure including the low‐temperature solution polycondensation of the bis(ether acyl chloride)s with three bis(o‐aminophenol)s, yielding poly(o‐hydroxyamide) precursors, and subsequent thermal cyclodehydration. The intermediate poly(o‐hydroxyamide)s exhibited inherent viscosities of 0.39–0.98 dL/g. All of the poly(o‐hydroxyamide)s were amorphous and soluble in polar organic solvents such as N,N‐dimethylacetamide, and most of them could afford flexible and tough films via solvent casting. The poly(o‐hydroxyamide)s exhibited glass‐transition temperatures (T_g's) of 129–194 °C and could be thermally converted into corresponding polybenzoxazoles in the solid state at temperatures higher than 300 °C. All the polybenzoxazoles were amorphous and showed an enhanced T_g but a dramatically decreased solubility with to respect to their poly(o‐hydroxyamide) precursors. They exhibited T_g's of 216–236 °C through differential scanning calorimetry and were stable up to 500 °C in nitrogen or air, with 10% weight‐loss temperatures being recorded between 538 and 562 °C in nitrogen or air. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 914–921, 2003     

Aromatic polybenzoxazoles containing ether–sulfone linkages

A series of poly(o‐hydroxy amide)s having both ether and sulfone linkages in the main chain were synthesized via the low‐temperature solution polycondensation of 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoyl chloride and 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoyl chloride with three bis(o‐aminophenol)s including 4,4′‐diamino‐3,3′‐dihydroxybiphenyl, 3,3′‐diamino‐4,4′‐dihydroxybiphenyl, and 2,2‐bis(3‐diamino‐4‐hydroxyphenyl)hexafluoropropane. Subsequent thermal cyclodehydration of the poly(o‐hydroxy amide)s afforded polyethersulfone benzoxazoles. Most of the poly(o‐hydroxy amide)s were soluble in polar organic solvents such as N‐methyl‐2‐pyrrolidone; however, the polybenzoxazoles without the hexafluoroisopropylidene group were organic‐insoluble. The polybenzoxazoles exhibited glass‐transition temperatures (T_g) in the range of 219–282 °C by DSC and softening temperatures (T_s) of 242–320 °C by thermomechanical analysis. Thermogravimetric analyses indicated that most polybenzoxazoles were stable up to 450 °C in air or nitrogen. The 10% weight loss temperatures were recorded in the ranges of 474–593 °C in air and 478–643 °C in nitrogen. The methyl‐substituted polybenzoxazoles had higher T_g's but lower T_s's and initial decomposition temperatures compared with the corresponding unsubstituted polybenzoxazoles. For a comparative purpose, the synthesis and characterization of a series of sulfonyl polybenzoxazoles without the ether group that derived from 4,4′‐sulfonyldibenzoyl chloride and bis(o‐aminophenol)s were also reported. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2262–2270, 2001     

Polyamide‐6,6‐based blocky copolyamides obtained by solid‐state modification

Copolyamides based on polyamide‐6,6 (PA‐6,6) were prepared by solid‐state modification (SSM). Para‐ and meta‐xylylenediamine were successfully incorporated into the aliphatic PA‐6,6 backbone at 200 and 230 °C under an inert gas flow. In the initial stage of the SSM below the melting temperature of PA‐6,6, a decrease of the molecular weight was observed due to chain scission, followed by a built up of the molecular weight and incorporation of the comonomer by postcondensation during the next stage. When the solid‐state copolymerization was continued for a sufficiently long time, the starting PA‐6,6 molecular weight was regained. The incorporation of the comonomer into the PA‐6,6 main chain was confirmed by size exclusion chromatography (SEC) with ultraviolet detection, which showed the presence of aromatic moieties in the final high‐molecular weight SSM product. The occurrence of the transamidation reaction was also proven by ¹H nuclear magnetic resonance (NMR) spectroscopy. As the transamidation was limited to the amorphous phase, this SSM resulted in a nonrandom overall structure of the PA copolymer as shown by the degree of randomness determined using ¹³C NMR spectroscopy. The thermal properties of the SSM products were compared with melt‐synthesized copolyamides of similar chemical composition. The higher melting and higher crystallization temperatures of the solid state‐modified copolyamides confirmed their nonrandom, block‐like chemical microstructure, whereas the melt‐synthesized copolyamides were random. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5118–5129     

Characterization of poly(styrene‐co‐methacrylonitrile)s obtained by low‐temperature radiation polymerization and thermal degradation behavior measured by Py‐GC and CRTG

Poly(styrene‐co‐methacrylonitrile)s were polymerized in solutions with different polarities (n‐hexane and THF) by low‐temperature γ‐ray irradiation polymerization in a temperature range of −83.6–30 °C. It was found by IR measurement that the composition of the copolymers changed remarkably due to the effects of the polarity of solvents and the polymerization temperature. The thermal degradation behavior in the flash pyrolysis and in the continuous heating pyrolysis of these copolymers was measured by Py‐GC and controlled rate thermogravimetry (CRTG). The effects of the copolymer composition and sequence distribution on the thermal degradation behavior were investigated. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3569–3577, 2000     

Stress distribution in poly‐p‐phenylenebenzobisoxazole (PBO) fiber as viewed from vibrational spectroscopic measurement under tension. I. Stress‐induced frequency shifts of Raman bands and molecular deformation mechanism

To clarify the relationship between a molecular deformation mechanism and a high Young's modulus of poly‐p‐phenylenebenzobisoxazole (PBO), Raman spectra were measured for fibers subjected to a tensile stress along the chain axis. The stress‐induced frequency shift of the observed Raman bands could be reproduced reasonably by the normal‐mode calculation under a quasi‐harmonic approximation. The frequency position at zero stress and the shift factor of Raman bands were predicted for a PBO chain that agreed with the actually evaluated values. On the basis of these analyses, the molecular deformation mechanism of the PBO chain has been discussed in detail. The crystalline modulus of the PBO chain was calculated theoretically to be 458 GPa, in good agreement with the X‐ray observed value of 460 GPa. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1269–1280, 2002     

Stress distribution in poly‐p‐phenylenebenzobisoxazole (PBO) fiber estimated from vibrational spectroscopic measurement under tension. II. Analysis of inhomogeneous stress distribution in PBO fiber

Fourier transform Raman spectra were measured for poly‐p‐phenylenebenzobisoxazole (PBO) fiber subjected to a tensile stress, and the Raman shift factor (the frequency shift caused by 1 GPa tensile stress) depended strongly on the sample‐preparation condition. To clarify the reasons of this dependency, a mechanical series parallel model was adopted that could successfully and quantitatively explain the observed Raman shift factors and gave a concreate heterogeneous stress distribution in the PBO fibers. As a result, a mechanical series model was reasonable for PBO fiber. Broadening of Raman bands, which was observed when the PBO fiber was tensioned, could also be interpreted on the basis of an idea of heterogeneous stress distribution. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1281–1287, 2002     

Photoluminescent,liquid‐crystalline,and electrochemical properties of para‐phenylene‐based alternating conjugated copolymers

Novel liquid‐crystalline alternating conjugated copolymers [ P(P(6)CN‐alt‐Cz) and P(P(6)CN‐alt‐MeP) ] with phenylene and carbazolylene or phenylene with methyl substitution onto the main chain have been synthesized through palladium‐catalyzed Suzuki coupling reactions. The influence of the incorporation of carbazolylene and the substituted phenylene into the main chain on the thermal, mesomorphic, and luminescent properties has been investigated by Fourier transform infrared spectroscopy, thermogravimetry, differential scanning calorimetry, polarized optical microscopy, ultraviolet–visible spectroscopy, photoluminescence (PL), and cyclic voltammetry. These polymers show highly thermal stability, losing little of their weights when heated to 360 °C. The conjugated copolymers exhibit liquid crystallinity at elevated temperature. The existence of the chromophoric terphenyl core endows the copolymers with high PL and the polymer P(P(6)CN‐alt‐Cz containing carbazolylene unit can emit more pure blue light. All the copolymer films with low band gaps about 2.3–2.4 eV undergo reversible oxidation and reduction processes, significantly lower than the band gap of poly(p‐phenylene). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 434–442, 2010     

Synthesis and film formation of polycarbonate‐co‐ poly(p‐ethylphenol)

The enzyme‐catalyzed synthesis of poly(p‐ethylphenol) (PEP) has received considerable interest in recent years. Nevertheless, the limited molecular weights restricts its application. In our preliminary research, PEP was modified by copolymerization with polycarbonates through both transesterification at high temperature, and triphosgene at low temperature to form polycarbonate‐co‐poly(p‐ethylphenol) (PC‐co‐PEP). FTIR, NMR, GPC, and thermal analysis verified the formation of PC‐co‐PEP. The copolymers have an optical absorption in the UV range. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 169–178, 1999