Pr含量对Bi_5Fe_(0.5)Co_(0.5)Ti_3O_(15)室温多铁性的影响

采用改良的固相烧结工艺制备了Bi5-xPrxFe0.5Co0.5Ti3O15(BPFCT-x,x=0.25,0.50,0.75,0.80)陶瓷样品.X射线衍射结构分析表明:镨(Pr)含量对样品微观结构产生了影响,但所有样品均为层状钙钛矿结构;BPFCT-x样品的剩余极化强度(2Pr)随着掺杂量的增加呈现出先增大后减小的变化趋势,当Pr含量为0.75时,样品的2Pr达到最大值,为6.43μC/cm2.样品的磁性与铁电性能具有相同的变化规律,室温下样品的剩余磁化强度(2Mr)也呈现出先增大后减小的趋势,并且也在x=0.75时达到最大为0.097 emu/g.随着Pr掺杂量增大,样品的室温下铁电和铁磁性能得到明显改善,并且当掺杂量为0.75时,样品室温多铁性最好.Pr掺杂降低了样品中的缺陷浓度,从而提高了样品铁电畴动性,这有助于提高样品铁电性能.而样品铁磁性能的改善可能与Pr对样品晶格畸变产生的影响有关.     

Ca~(2+)掺杂对SmFeO_3的介电、铁磁特性及磁相变温度的影响

采用固相反应法制备Sm_(1-x)Ca_xFeO_3(x=0,0.1,0.2,0.3)样品,研究Ca~(2+)掺杂对SmFeO_3介电性能、铁磁性及磁相变温度的影响.X射线衍射图谱分析表明:所有样品的主衍射峰与SmFe03相符合且具有良好的晶体结构.随着x的增加,SmFeO_3样品的晶粒尺寸由原来的0.5μm逐渐增大到2μm.当f=1 kHz时,Sm_(1-x)Ca_xFeO_3(x=0.1,0.2,0.3)样品的ε_r分别是SmFe03的5倍、3倍和2.6倍,而tgσ增大一个数量级.在3T磁场作用下,SmFe03样品的M-H呈线性,随着x的增加,M-H逐渐趋向饱和,Sm_(1-x)Ca_xFeO_3(x=0.1,0.2,0.3)样品的M_r分别是SmFeO_3的20倍、31倍和68倍.X射线光电子能谱分析表明:Fe~(2+)和Fe3+共存于Sm_(1-x)Ca_xFeO_3样品中,Fe~(2+)/Fe~(3+)比例随着x的增加而增大,证明Ca~(2+)掺杂增加了Fe~(2+)的含量,形成Fe~(2+)—O~(2-)—Fe~(3+)超交换作用,增强SmFe03的铁磁特性.测量了Sm_(1-x)Ca_xFeO_3样品在外加磁场为1000 Oe(1 Oe=79.5775 A/m)的M-T变化关系,观测到其自旋重组温度(T_(SR))和尼尔温度(T_N)分别为438 K和687 K,发现SmFe03样品的T_(SR)和T_N均随着x的增加向低温方向移动,当x=0.3时,自旋重组现象消失.这主要是SmFeO_3样品磁结构的稳定性和Fe~(3+)—O~(2-)—Fe~(3+)及Sm~(3+)—O~(2-)—Fe~(3+)超交换三者共同作用的结果.     

Co含量对Bi6Fe2-xCoxTi3O18样品多铁性的影响

用固相工艺制备了Bi₆Fe_2-xCo_xTi₃O₁₈ (BFCT-x, x=0, 0.2, 0.6, 0.8, 1.0, 1.2, 1.6, 1.8, 和2.0)多铁陶瓷样品, 样品X射线谱分析发现, 随着Co含量的增加, 样品晶格常数出现了先增大后减小的变化. 室温下, BFCT-0.6样品呈现出相对较高的饱和磁化强度, 2M_s约为4.49 emu/g, BFCT-1.0具有最高的剩余磁化强度, 2M_r约为0.89 emu/g. Co含量在0.2 ≤x≤qslant 1.2范围内, 随着Co含量的增加样品顺磁–铁磁相变温度从752 K降至372 K. 小量的Co改善了样品的铁电性能, 当x=0.6时样品样品的铁电性能最佳, 随着含量增大样品铁电性能下降, 但当x >1.2时样品的铁电性能又得到了改善.     

钆掺杂对0.7BiFe_(0.95)Ga_(0.05)O_3-0.3BaTiO_3陶瓷的结构、介电性能和多铁性能的影响

采用固相烧结法制备了不同Gd掺杂含量的0.7Bi_(1-x)Gd_(x)Fe_(0.95)Ga_(0.05)O_(3)-0.3BaTiO_3(BG_xFG-BT,x=0,0.05,0.1,0.15,0.2)陶瓷,系统研究了Gd掺杂对BG_xFG-BT陶瓷的晶体结构、微观形貌、介电性能以及多铁性能的影响.通过X射线衍射图谱分析、扫描电镜形貌分析、X射线光电子能谱分析等工具表明,Gd掺杂会使BG_xFG-BT陶瓷由菱面体(R3c)结构转变为赝立方(P4mm)结构,晶粒尺寸会明显减小,从未掺入Gd时的6.2μm)降低到约3.2μm左右,同时发现少量的Gd掺杂能够抑制BFG-BT陶瓷中Fe~(2+)离子的产生,减少氧空位的存在.最终导致,在适量的Gd掺杂下,陶瓷的介电性能和铁电性能均得到明显改善.适量的Gd掺杂可使介电常数增加、介电损耗减少、电滞回线形状改善、剩余电极化强度增加(最高达9.06μC/cm~2).同时,在磁性能方面,Gd掺杂陶瓷均表现铁磁性,剩余磁极化强度与饱和磁化强度均有显著提高.     

La掺杂对钇铁石榴石陶瓷磁性及磁介电性能的影响

采用传统的固相烧结法制备了La掺杂的Y_3Fe_5O_(12)系列陶瓷样品。详细研究了La掺杂对肯磁性和磁介电性能的影响.研究结果表明:随着La掺杂量的增加,饱和磁化强度和本征磁介电效应先增加后减小,归因于Fe~(2+)离子含量的非单调变化.分析认为,具有较大离子半径的La~(3+)对Y~(2+)替代导致Y_3 Fe_5 O_(12)晶格扩张和可能的离子移位,这两个因素的竞争作用引起Fe~(2+)含量随La含量的增加先增加后减小.Fe~(2+)离子含量的非单调变化导致饱和磁化强度和磁介电效应的相应变化趋势,并在La含量为0.3时同时获得了大的饱和磁化强度和磁介电效应,在10~6Hz和0.9 T条件下的室温磁介电系数达-5%.     

近红外长余辉纳米探针ZnGa_2O_4∶Cr~(3+),Sn~(4+)的制备及Fe~(3+)含量的时间分辨检测

鉴于长余辉材料免实时激发特性可有效消除激发光源及复杂样品自体荧光的干扰,近红外长余辉材料在生物成像领域受到了广泛关注。但其在荧光传感应用方面的报道相对较少,尤其是利用长余辉纳米粒子来检测金属阳离子鲜有报道。本文采用水热法制备了Sn~(4+)共掺的近红外长余辉纳米材料ZnGa_2O_4∶Cr~(3+),Sn~(4+)(ZGSC),再以包硅处理得到在水溶液中分散性良好的荧光探针ZnGa_2O_4∶Cr~(3+),Sn~(4+)@SiO_2(ZGSC@SiO_2)。基于Fe~(3+)对长余辉材料ZGSC@SiO_2的荧光猝灭效应,构建了一种选择性好、无背景干扰的近红外长余辉荧光探针ZGSC@SiO_2,用于Fe~(3+)的定量检测。采用时间分辨光谱可有效地消除背景干扰,实现了高信噪比检测,其线性范围为50～800μmol/L,检出限为25.12μmol/L。选取了3种补铁口服液作为实际样品,对其总铁含量以及Fe~(3+)的含量进行检测,并进行了加标实验。实验结果表明,测定结果中总铁含量与标示值吻合;3种样品中总铁含量的加标回收率为99.00%～99.79%,相对标准偏差(RSD)为2.416%～3.808%;Fe~(3+)含量的加标回收率为99.90%～102.69%,RSD为3.263%～4.296%,满足测定要求。根据样品中总铁含量和Fe~(3+)含量,可计算得出Fe~(2+)含量,因此该荧光传感体系具有可同时检测Fe~(3+)与Fe~(2+)的优点,可以用于补铁口服液中有效价态Fe~(2+)的质量控制检测。     

(Bi, La)4Ti3O12-Sr(Bi, La)4Ti4O15共生结构铁电材料性能研究

采用固相烧结工艺,制备了不同La掺杂量(x=0.00,0.25,0.50,0.75,1.00,1.25和1.50)的(Bi, La)4Ti3O12-Sr(Bi, La)4Ti4O15 (SrBi8-xLaxTi7O27)共生结构铁电陶瓷样品.用x射线衍射对其进行微结构分析,并测量铁电、介电性能.结果发现,La掺杂未改变Bi4Ti3O12-SrBi4Ti4O15共生结构铁电材料的晶体结构.随掺杂量的增加,样品的矫顽场(Ec)略有增加,剩余极化(2Pr)先增大,后减小.在x＝0.50时,2Pr达到极大值,为25.6 μC*cm-2,与Bi4Ti3O12-SrBi4Ti4O15相比,2Pr增加了近60%,而Ec仅增加约10%.随La掺杂量的增加,样品的居里温度TC逐渐降低,x＝0.50时,TC=556 ℃.在x=1.50时,样品出现弛豫铁电体的典型特征.     

La_(2)ATiO_(6)(A=Mg,Zn)∶Er^(3+)荧光材料的上转换发光特性及温度传感特性调控EI北大核心CSCD

Er^(3+)的上转换性能强烈依赖局部位置对称畸变。在本研究中,采用高温固相法制备了La_(2)Mg_(1-w)Zn_(w)TiO_(6)∶xEr^(3+)(x=0,0.02,0.04,0.06,0.08,0.10;w=0,0.3,0.5,0.7,1.0)系列荧光粉。基于XRD精修,Zn^(2+)的掺杂改变了La_(2)Mg⁃TiO_(6)晶体的配位环境,晶相由Pbnm转变为P2_(1/n)。在980 nm激光激发下,样品上转换荧光强度随Er^(3+)离子浓度改变,当Er^(3+)离子浓度为x=0.06时样品的上转换荧光强度最强。基于荧光强度比技术研究了样品La_(2)Mg_(1-w)ZnwTiO_(6)∶xEr^(3+)(x=0.06;w=0,0.3,0.5,0.7,1.0)在303~583 K温度范围内的上转换荧光温度传感特性。实验结果表明,灵敏度随着Mg^(2+)和Zn^(2+)掺杂浓度比例的改变而改变,在w=1.0时达到最大绝对灵敏度0.90%·K^(-1),说明Zn^(2+)的掺杂提高了La_(2)MgTiO_(6)的灵敏度。     

钙钛矿钴氧化物La_(0.5-x)Nd_xSr_(0.5)CoO_3(x=0,0.1,0.15)的磁性和电输运性质

本文采用传统固相反应法制备多晶La_(0.5-x)Nd_xSr_(0.5)CoO_3(x=0,0.1,0.15)系列样品,通过测量其磁化强度与温度变化曲线(M~T)、磁化强度与外场变化曲线(M~H)、电子自旋共振谱(ESR)和电阻率与温度变化曲线(ρ~T)对样品的磁性和电输运性质进行了研究.结果表明:由于Nd~(3+)离子掺杂,使得系统中Co~(3+)和Co~(4+)离子之间的铁磁耦合增大,自旋与晶格的耦合作用增强,从而导致掺杂前后样品的磁性方面发生了改变:样品的铁磁转变温度TC和磁熵变值|ΔSM|均随掺杂量x的增加而增大,三个样品的TC分别为:190K、205K和233K,x=0.0样品在TC附近的相变为二级相变,x=0.1和x=0.15样品在TC附近的相变为一级相变.同样的,Nd~(3+)离子掺杂使得样品在电输运性质方面也发生了改变:由于Nd~(3+)离子掺杂,体系内Co离子的自旋态和无序性等均发生改变,从而使x=0.1样品中铁磁导电区域增大,尽管x=0.0和x=0.1样品均表现出绝缘体行为,但是随着掺杂量x的增加,电阻率大幅降低.     

Dy掺杂对Sr2Bi4Ti5O18铁电陶瓷性能的影响

用传统固相烧结法制备了Sr₂Bi_4-xDy_xTi₅ O₁₈(SBDT-x, x=0—0.20)陶瓷样品. x射线衍射分析表明, 微量的Dy掺杂没有影 响Sr₂Bi₄Ti₅O₁₈(SBTi) 原有的层状钙钛 矿结构. 通过研究样品的介电特性, 发现Dy掺杂减小了材料的损耗因子, 降低了样品铁电- 顺电相转变的居里温度. 铁电性能测量结果表明, 随Dy含量的增加, SBDT-x系列样品的剩余 极化先增大, 后减小. 当Dy掺杂量为0.01时, 剩余极化达到最大值, 约为20.1 μC·cm^-2. 掺杂引起剩余极化的变化, 与材料中缺陷浓度、内应力以及晶格畸变程度等因 素有关, 是多种作用机理相互竞争的结果. (Bi₂O₂)²⁺ 层通常被看作是绝缘层和空间电荷库, 对材料的铁电性能起关键作用. 掺杂离子进入(Bi2O₂)²⁺层会导致铁电性能变差. 关键词： 2Bi₄Ti₅O₁₈陶瓷')" href="#">Sr₂Bi₄Ti₅O₁₈陶瓷 Dy掺 杂 铁电性能 居里温度     

Magnetic properties in BaFe12O19 nanoparticles prepared under a magnetic field

It was observed that the nanocrystallites of BaFe₁₂O₁₉ formed at 140°C under a 0.25 T magnetic field exhibited a higher saturation magnetization (6.1 emu/g at room temperature) than that of the sample (1.1 emu/g) obtained under zero magnetic field. Both of the two approaches yielded plain-like particles with an average particle size of 12 nm. However, the Curie temperature (T_c), a direct measuring of the strength of superexchange interaction of Fe³⁺–O²⁻–Fe³⁺, increased from 410°C for the nanoparticles prepared without an external field applied to 452°C for the particles formed under a 0.25 T magnetic field, which indicates that external magnetic fields can improve the occupancy of magnetic ions and then increase the superexchange interaction. This was confirmed by electron paramagnetic resonance and Mössbauer spectrum analysis. The results present in this paper suggest that in addition to oxygen defects, surface non-magnetic layer and a fraction of finer particles in the superparamagnetic range, cation vacancies should be responsible for the decreasing of saturation magnetization in magnetic nanoparticles.     

Effects of pH and citric acid contents on characteristics of ester-derived BaFe12O19 powder

The single domain size of BaFe₁₂O₁₉ powder with crystallite sizes less than 200 nm was produced using a citric acid precursor method. Fe³⁺ and Ba²⁺, in a molar ratio of 12, were chelated by COOH⁻ in an aqueous solution. After ethylene glycol additions, esterification, dehydration, and calcination led to the formation of ester-derived BaFe₁₂O₁₉ powder. High pH and/or high citric acid contents in the starting solution are required to complete chelate metallic ions in the solution and to form pure barium ferrite powder at 1073 K. Pure single magnetic domain BaFe₁₂O₁₉ particles of M(30 kOe)≈54 emu/g, M_r≈28 emu/g, and H_c≈3.7 kOe were produced using [citric acid]/[metallic ions]=1.5 and pH7.     

Sonochemically assisted synthesis of zinc-doped maghemite

Nanoparticles of zinc-doped maghemite were prepared using ultrasonic radiation. As a precursor, a suspension of maghemite in an alkaline aqueous solution of zinc nitrate at pH 9 was sonicated. The zinc-doped maghemite nanoparticles were investigated by X-ray diffraction, Mössbauer spectroscopy, high-resolution electron microscopy (HREM) and SQUID magnetometry. The Mössbauer measurements, which cover the temperature range 4.2 K to room temperature, were acquired in zero field and an applied field of 5 T. The results show that by using ultrasound radiation, zinc Zn²⁺ can substitute for Fe³⁺ up to a composition close to zinc ferrite (ZnFe₂O₄), which has a random distribution of Fe³⁺ ions over both A and B sublattices in the spinel structure with an inversity parameter of δ = 0.322. This leads to a maximum saturation magnetization (M_s) of 64.1 emu/g at 300 K and 73.5 emu/g at 2 K.     

Electrical and magnetic properties of polyaniline/Fe3O4 nanostructures

We report on electrical and magnetic properties of polyaniline (PANI) nanotubes (150 nm in diameter) and PANI/Fe₃O₄ nanowires (140 nm in diameter) containing Fe₃O₄ nanoparticles with a typical size of 12 nm. These systems were prepared by a template-free method. The conductivity of the nanostructures is 10⁻¹–10⁻² S/cm; and the temperature dependent resistivity follows a ln ρT^−1/2 law. The composites (6 and 20 wt% of Fe₃O₄) show a large negative magnetoresistance compared with that of pure PANI nanotubes and a considerably lower saturated magnetization (M_s=3.45 emu/g at 300 K and 4.21 emu/g at 4 K) compared with the values measured from bulk magnetite (M_s=84 emu/g) and pure Fe₃O₄ nanoparticles (M_s=65 emu/g). AC magnetic susceptibility was also measured. It is found that the peak position of the AC susceptibility of the nanocomposites shifts to a higher temperature (>245 K) compared with that of pure Fe₃O₄ nanoparticles (190–200 K). These results suggest that interactions between the polymer matrix and nanoparticles take place in these nanocomposites.     

Ferromagnetic Zr1−xMnxCo2 laves phase compounds

Structure and magnetic properties of the Zr_1−xMn_xCo_2+δ alloys were studied for 0 x <0.7, δ=0, 0.45. The cubic C15 Laves phase structure shows Mn solubility up to x≈0.4. The other Laves phase with the hexagonal C36 structure found for x0.5 apparently has a small region of Mn solubility in the vicinity of Zr_0.4Mn_0.6Co₂. Though the parent Mn-free compounds are known to be paramagnetic, the Mn-substituted alloys show ferromagnetic behavior with the Curie temperatures up to 625 K and the room-temperature saturation magnetization of about 100 emu/g. The onset of ferromagnetism with the Mn substitution for Zr may be caused by polarization of itinerant 3d electrons, like it was earlier supposed for the off-stoichiometric ZrCo_2+δ. The universal composition dependencies of the intrinsic magnetic properties for different δ can be obtained, if plotted against the amount of zirconium atoms missing in its sublattice. The room-temperature anisotropy with the noticeable anisotropy field of 24 kOe and the 1 1 0 easy magnetization direction laying in a basal plane was found in the hexagonal Zr_0.5Mn_0.5Co₂.     

顺磁性La2/3Sr1/3MnO3层对Bi0.8Ba0.2FeO3薄膜多铁性能的影响

界面效应在提升异质结构材料的多铁性能方面有着重要的作用. 本文采用脉冲激光沉积技术在SrTiO₃(STO)基片上制备了Bi_0.8Ba_0.2FeO₃(BBFO)/La_2/3Sr_1/3MnO₃(LSMO)异质结. X-射线衍射图谱表明异质结呈现单相外延生长, 利用高分辨透射电镜进一步证实了BBFO为四方相结构. X-射线光电子能谱证实异质结中只存在Fe³⁺ 离子, 没有产生价态的变化, 揭示了异质结铁电和铁磁性的增强与BBFO/LSMO的界面有关. 同时, 测试了磁电阻(MR)和磁介电(MD), 当磁场强度为0.8 T, 温度为70 K时, MR约为-42.2%, MD约为21.2%. 并且发现在180 K时出现磁相的转变. 实验结果揭示出异质界面效应在提升材料的多铁性和磁电耦合效应方面具有超常的优点, 是加快多铁材料实际应用的有效途径.     

Magnetic properties of xFe2O3(1−x)[B2O3 · PbO] glasses

The magnetic measurements performed on xFe₂O₃(1-x)[B₂O₃ · PbO] glasses show that for x 5 mol.% Fe₂O₃ the thermal variation of reciprocal susceptibility obeys a Curie behaviour. For higher iron content, at T 50 K, a nonlinear variation, typical for systems with random distribution of exchange interactions is observed. At greater temperatures than 50 K a Curie-Weiss behaviour is shown. The composition dependence of the Curie constants is analysed in correlation with the number of Fe³⁺ and Fe²⁺ ions as determined from Mössbauer effect measurements. A comparison with the data obtained in case of xFe₂O₃(1-x)[3B₂O₃ · PbO] glasses is made.     

R型铁氧体BaFe4-xTi2+xO11的化学组态以及磁性行为的研究

本文通过传统的固相反应法制备了R型六角铁氧体BaFe_4-xTi_2+xO₁₁ (x= 0, 0.25, 0.5, 0.75, 1), 并且对它的原子价态以及磁性行为进行了研究. X 射线光电子能谱(XPS)结果显示了随着掺杂含量的增加, 体系中Fe³⁺离子逐渐减少而Fe²⁺离子逐渐增加. 由于具有非对称结构的阻挫晶格中存在各种关联作用的竞争, 使得BaFe_4-xTi_2+xO₁₁体系表现出了复杂的磁有序行为, 在T₁～250 K和T₂～83 K两处存在磁转变. 对这一系列掺杂样品, 在相变温度T₁之上表现顺磁行为, 而在相变温度T₂前后的磁化强度都表现出低场下随磁场的增加快速增加, 高场下则线性变化且在5×10⁴ Oe时还未达到饱和的行为, 表明这一系列掺杂样品是典型的倾斜反铁磁态(canted antiferromagnetic) 或者亚铁磁态.