添加碱金属对甲烷与空气制合成气的催化剂性能的影响

考察了添加在镍基催化剂中的碱金属助剂 ,对甲烷与空气制合成气的催化反应性能的影响 ;并用 TPO、TPR、CO2 程序升温脱附 (TPD)、XPS及 CO脉冲色谱技术 ,对催化剂进行了表征 .实验表明 ,碱金属助剂对降低催化剂结炭有一定的作用 ,催化剂的抗积炭性能为 Ni- K2 O/Ca O- Al2 O3>Ni- L i2 O/Ca O- Al2 O3>Ni- Na2 O/Ca O-Al2 O3>Ni/Ca O- Al2 O3.在实验中发现 ,碱金属的添加 ,可使催化剂的 Ni比表面积变小、吸附 CO2 的能力增强 ,且结合能可发生不同程度的改变 .从而解释了碱土金属助剂对催化剂活性和抗积炭性的影响 .实验显示 ,Ni-L i2 O/Ca O- Al2 O3具有较好的活性和抗积炭性能     

Ni/Al2 O3 催化剂上甲烷的分解温度和时间对积炭的影响

用在线质谱法研究了Ni/Al2O3催化剂上甲烷分解温度和时间对积炭的影响。实验结果表明：在600～800℃内甲烷在还原的Ni/Al2O3催化剂上可分解为表面碳物种（即NiXC）和氢气,这种表面碳物种在较低的温度下可扩散进入体相,在高温下可逐步转化为低活性的碳物种。在800℃下由于表面碳物种不能扩散进入体相,金属镍中心迅速被表面碳物种覆盖,导致甲烷分解反应失活。     

Carbon Dioxide Reforming of Methane over Ni Catalysts Supported on Al2O3 Modified with La2O3, MgO, and CaO

The preparation of synthesis gas from carbon dioxide reforming of methane (CDR) has attracted increasing attention. The present review mainly focuses on CDR to produce synthesis gas over Ni/MO_x/Al₂O₃ (X = La, Mg, Ca) catalysts. From the examination of various supported nickel catalysts, the promotional effects of La₂O₃, MgO, and CaO have been found. The addition of promoters to Al₂O₃-supported nickel catalysts enhances the catalytic activity as well as stability. The catalytic performance is strongly dependent on the loading amount of promoters. For example, the highest CH₄ and CO₂ conversion were obtained when the ratios of metal M to Al were in the range of 0.04–0.06. In the case of Ni/La₂O₃/Al₂O₃ catalyst, the highest CH₄ conversion (96%) and CO₂ conversion (97%) was achieved with the catalyst (La/Al = 0.05 (atom/atom)). For Ni/CaO/Al₂O₃ catalyst, the catalyst with Ca/Al = 0.04 (atom/atom) exhibited the highest CH₄ conversion (91%) and CO₂ conversion (92%) among the catalysts with various CaO content. Also, Ni/MgO/Al₂O₃ catalyst with Mg/Al = 0.06 (atom/atom) showed the highest CH₄ conversion (89%) and CO₂ conversion (90%) among the catalysts with various Mg/Al ratios. Thus it is most likely that the optimal ratios of M to Al for the highest activities of the catalysts are related to the highly dispersed metal species. In addition, the improved catalytic performance of Al₂O₃-supported nickel catalysts promoted with metal oxides is due to the strong interaction between Ni and metal oxide, the stabilization of metal oxide on Al₂O₃ and the basic property of metal oxide to prevent carbon formation.     

Influence of Support Type and Metal Loading in Methane Decomposition over Iron Catalyst for Hydrogen Production

Natural gas resources, stimulate the method of catalytic methane decomposition. Hydrogen is a superb energy carrier and integral component of the present energy systems, while carbon nanotubes exhibit remarkable chemical and physical properties. The reaction was run at 700 °C in a fixed bed reactor. Catalyst calcination and reduction were done at 500 °C. MgO, TiO₂ and Al₂O₃ supported catalysts were prepared using a co‐precipitation method. Catalysts of different iron loadings were characterized with BET, TGA, XRD, H₂‐TPR and TEM. The catalyst characterization revealed the formation of multi‐walled nanotubes. Alternatively, time on stream tests of supported catalyst at 700 °C revealed the relative profiles of methane conversions increased as the %Fe loading was increased. Higher %Fe loadings decreased surface area of the catalyst. Iron catalyst supported with Al₂O₃ exhibited somewhat higher catalytic activity compared with MgO and TiO₂ supported catalysts when above 35% Fe loading was used. CH₄ conversion of 69% was obtained utilizing 60% Fe/Al₂O₃ catalyst. Alternatively, Fe/MgO catalysts gave the highest initial conversions when iron loading below 30% was employed. Indeed, catalysts with 15% Fe/MgO gave 63% conversion and good stability for 1 h time on stream. Inappropriateness of Fe/TiO₂ catalysts in the catalytic methane decomposition was observed.     

Effect of Calcined Temperature on Coke Deposition for Autothermal Reforming of Methane with Ni-Cu Catalyst

Ni/CuO-ZrO₂-CeO₂-Al₂O₃ catalysts were prepared by co-precipitation method at pH=9 and using Na₂CO₃ as the precipitant. The Ni loading (mass fraction) of the catalysts was 10%. The catalysts were characterized by X-ray diffraction, temperature-programmed oxidation (TPO), scanning electron microscope (SEM), and X-ray photoelectron spectroscopy (XPS). The effects of calcined temperature of support on coke deposition were studied. TPO, SEM and XPS results indicated there was no peak of higher temperature oxygen consumption on Ni/CuO-ZrO₂-CeO₂-Al₂O₃catalyst (support was calcined at 800 ^oC), which could lead to the deactivation of the catalyst. The carbon species were carbonate and inactive carbon (filamentous carbon species) on the surface of catalyst reacting for 40 h which perhaps led to the deactivation of the catalyst.     

Ni／MgO／Al2O3催化剂中Ni前体对甲烷—二氧化碳重整反应活性的影响

考察了以硝酸镍、氯化镍、硫酸镍、醋酸镍及硝酸六氨合镍5种Ni盐制备的Ni/MgO/Al2O3催化剂在CO2与CH4重整制合成气反应中的催化活性,发现Ni前体对活性有明显的影响,以硝酸镍、醋酸镍、硝酸六氨合镍为前体制备的Ni催化剂,反应性较高;以硫酸镍为前体制备的Ni催化剂,可能由于硫中毒等原因而显示出很低的活性;以氯化镍为前体制备的 Ni催化剂,其活性与制备方法有关,未经烧而直接还原的催化剂显示出较好的活性,X－射线粉末衍射（XRD）、BET比表面积及反应后的积量测定结果表明,以硝酸镍、醋酸镍、硝酸六氨合镍为前体制备的Ni催化剂,表面分散性好,比表面积大,积炭量少。     

焙烧温度对 Pd/Al2O3 催化剂上甲烷燃烧反应性能的影响

 考察了载体与催化剂焙烧温度对 Pd/Al2O3 催化剂上低浓度甲烷催化燃烧反应性能的影响. 采用 X 射线衍射、透射电镜、N2 物理吸附、NH3 程序升温脱附和 O2 程序升温氧化等手段对载体和催化剂进行了表征. 结果表明, 焙烧温度对催化剂活性及稳定性的影响显著. 随着载体焙烧温度的升高, Al2O3 的比表面积、物相结构、酸中心的数量及强度明显改变, 相应的 Pd/Al2O3 催化剂中载体与 Pd 的相互作用减弱, Pd 分散度降低. 当载体焙烧温度为 1 100 °C, Pd/Al2O3 焙烧温度为 200 °C 时, 所得催化剂在 260 h 的连续反应中, 甲烷转化率始终维持在 99%以上.     

La2O3 和CeO2对CH4-CO2重整Ni/MgO催化剂结构和性能的影响

采用共沉淀方法制备了NiO-MgO、NiO-La2O3-MgO、NiO-CeO2-MgO三种催化剂，用BET、XRD、TPR、XPS、TG及活性评价等方法考察了La2O3、CeO2助剂对NiO-MgO物化性质和CH4-CO2重整反应性能的影响.实验结果表明，三种催化剂中镍物种以镍镁固溶体形式存在.与NiO-MgO相比， NiO-La2O3-MgO、NiO-CeO2-MgO具有较高比表面积，且其镍物种可还原能力有所增强， NiO-CeO2-MgO尤为明显. La2O3、CeO2均在一定程度上改善了NiO-MgO的CH4-CO2重整反应性能，提高了镍晶粒的抗烧结能力.但二者的作用机制有所差异， La2O3和CeO2分别主要作为结构助剂和电子助剂发挥作用.     

焙烧温度对乙苯脱氢催化剂Fe2O3-K2O性能的影响

用混合法制备了Fe2O3-K2O乙苯脱氢催化剂,并用压汞法、X射线衍射、穆斯堡尔谱、程序升温还原和热重-差热分析等表征手段,考察了焙烧温度对催化剂的催化活性、比表面积、体相结构和还原性能的影响.结果表明,随着焙烧温度的升高,催化剂的比表面积逐渐减小,平均孔径逐渐增大;尖晶石K2Fe22O34中正四面体Fe3 的含量逐渐减少,正八面体Fe3 的含量逐渐增多,催化剂逐渐变得容易被还原;催化剂的催化活性差别不大,但达到平稳时所需的诱导期逐渐缩短.过高的焙烧温度不利于催化剂的稳定性.     

一种新的甲烷低温燃烧催化剂Au—Pt／Co3O4

考察了Pt和Pd的引入对Au/Co3O4催化剂的甲烷燃烧活性的影响,发现在Au/Co3O4（Au的质量分数为2%-5%）催化剂中掺入少量的Pt(如0.2%）,可使甲烷的催化燃烧活性得到显著的提高;相对于Au/Co3O4催化剂,其甲烷的最低全转化温度降低了50℃。便Pd的引入未提高甲烷燃烧的活性。表明Au-Pt/Co3O4是一个很有应用潜力的甲烷低温燃烧催化剂。     

Influence of Electronic Effect on Methane Catalytic Combustion over PdNi/Al2O3

A series of PdNi/Al₂O₃ catalysts with different compositions was prepared by co-reduction method. The influence of Ni amount on the catalytic combustion of methane was studied. X-ray diffractometry and X-ray photo-electron spectroscopy were employed to characterize the dispersion and electronic state of the active phase. Tempe-rature-programmed oxidation was carried out to study the thermal stability affected by Ni doping. It has been demonstrated that Ni addition changed particle size and oxidation state of PdO_x. The results indicate that the promotion of Ni to the Pd/Al₂O₃ resulted from both size effect and electronic effect. In addition, the thermal stability of the Ni-doped catalysts were enhanced.     

Synthesis of Tungsten Oxide Nanorods by the Controlling Precipitation Reaction: Application for Hydrogen Evolution Reaction on a WO3 Nanorods/Carbon Nanotubes Composite Film Modified Electrode

Tungsten trioxide nanorods (WO₃) were prepared by controlling the precipitation reaction of sodium tungstate dehydrates solution and hydrothermal process. The synthesized tungsten trioxide nanorods have been characterized by X‐ray diffraction (XRD), energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), cyclic voltammetry (CV) and linear sweep voltammetry (LSV). Electrochemical activity for hydrogen evolution reaction (HER) on WO₃ nanorods / carbon nanotube (WO₃/CNT) composite electrocatalyst was first studied in acid solution (0.1 M H₂SO₄) at room temperature. The overall experimental results revealed that the electrocatalytic activity for HER on WO₃/CNT is two order magnitude higher than those obtained with WO₃ nanorods and is four times than in the case of commercial WO₃ in 0.1 M H₂SO₄. On the other hand, the kinetic reaction mechanisms were discussed on WO₃/CNT electrocatalysts in acid solution for HER. However, the rate‐determining step carries through Tafel reaction on commercial WO₃, CNT, WO₃ nanorods and WO₃/CNT electrocatalysts in acidic solution was introduced.     

TiO2-Al2O3复合氧化物载体焙烧温度对Au-Pd催化剂加氢脱硫性能的影响

 采用溶胶-凝胶法制备了介孔TiO2-Al2O3复合氧化物载体,考察了载体的焙烧温度对负载型Au-Pd双金属催化剂加氢脱硫性能的影响,并采用X射线衍射、吸附吡啶的程序升温脱附、程序升温还原、红外光谱和N2物理吸附等技术对载体及催化剂进行了表征. 结果表明,不同温度焙烧的TiO2-Al2O3复合载体都具有介孔结构,其中773 K焙烧制得的TiO2-Al2O3复合载体的比表面积和孔容较大, B酸中心较多,以其为载体的Au-Pd 催化剂具有较好的加氢脱硫活性. 表征结果表明, 773 K焙烧制得的Au-Pd/TiO2-Al2O3催化剂中Au-Pd活性组分与载体的相互作用较强,催化剂上形成的AuxPdy合金的晶粒较小且数量较多,催化剂的酸量和活性组分的分散度较大,并且其上进行的加氢脱硫反应的活化能较低,这些因素均有利于催化剂活性的提高.     

Effect of Calcination Temperature and Pretreatment with Reaction Gas on Properties of Co/γ‐Al2O3 Catalysts for Partial Oxidation of Methane

The effects of calcination temperature and feedstock pretreatment on the catalytic performance of Co/γ‐Al₂O₃ catalysts were studied for partial oxidation of methane (POM) to synthesis gas, with emphasis on the role of feedstock pretreatment. The physicochemical properties of the catalysts were characterized by N₂ adsorption, X‐ray diffraction (XRD), transmission electron microscopy (TEM), H₂ temperature‐programmed reduction (H₂‐TPR), and Raman spectroscopy. The results showed that the pretreatment of the catalyst by reaction gas significantly improved the catalytic activity and stability for the POM reaction. On the other hand, the effect of calcination temperature was less significant. Although the initial activity was increased by an increased calcination temperature, the catalyst without the feedstock pretreatment suffered a rapid deactivation. The reaction‐atmosphere pretreatment was revealed as a process that mainly modified the surface structure of the catalyst. In that process, the formation of a CoAl₂O₄‐like compound led to high Co metal dispersion after reduction, and the transformation of the carrier into α‐Al₂O₃ occurred over the catalyst surface. Both the high dispersion of cobalt and the presence of α‐Al₂O₃ surface phase were assumed as the important factors resulting in an excellent catalytic performance in terms of high activity and high stability.     

Ni-Al2O3催化剂焙烧温度对丙烷催化还原NO反应性能的影响

环境污染与防治问题全球瞩目,而一氧化氮作为最难消除的大气污染物之一,已日益受到世界各国的重视.金属氧化物催化剂是研究贫燃条件下烃类选择催化还原NO的一个重要方向[1~3],以氧化铝为载体的镍催化剂虽然表现出很高的活性[4,5],但是催化剂结构对NO转化活性的影响并未见详细报     

Pd/Co3O4纳米颗粒负载于Al2O3纳米片高效催化甲烷燃烧

We report an efficient catalyst composed of ternary components prepared by inlaying Pd/Co₃O₄ nanoparticles in alkaline Al₂O₃ nanosheets for catalytic oxidation of methane. Pd/Co₃O₄ inlaid in alkaline Al₂O₃ exhibited a higher ability to break the C-H bond of methane than Pd/Co₃O₄ supported on SiO₂, ZrO₂, CeO₂, and acidic or neutral Al₂O₃. Our results show more oxygen vacancies and higher amounts of surface adsorbed oxygen on the surface of Pd/Co₃O₄/alkaline Al₂O₃ than on other catalysts, which is responsible for methane activation and conversion. Further, the Pd/Co₃O₄/alkaline Al₂O₃ catalyst can almost restore to its initial value in the absence of water when 5% (volume fraction) vapor water was cut off, although a decrease in activity occurred when water vapor was introduced to the reaction system. Even under a condition similar to the exhaust of a lean-burn natural gas engine, the catalytic performance of the Pd/Co₃O₄/alkaline Al₂O₃ catalyst is excellent, that is, methane could be completely converted when the sample temperature in the reaction atmosphere was ramped to 400℃.     

CO偶联临氢反应Pd-Fe/Al2O3催化剂的XPS研究

 利用XPS及氩离子溅射等技术对CO偶联和临氢反应中所用催化剂\r\n表面活性组分和助剂的含量及其化学状态进行了分析，并通过测定氢在\r\n催化剂表面的化学吸附，以及氢浓度对催化剂活性的影响，探讨了CO偶\r\n联反应中催化剂临氢失活的主要原因．XPS表征结果表明，CO偶联反应\r\n中催化剂活性组分以Pd0和Pd2＋形式共存；而临氢反应后仅以Pd0形式\r\n存在，助剂FeO从催化剂的内部向表面迁移且有少量Fe2＋转变为Fe3＋\r\n．催化剂临氢失活的主要原因是H2在活性组分Pd及助剂Fe（主要是FeO\r\n）表面均可形成解离吸附，形成的金属氢化物可在低活化能条件下发生\r\n迁移．这种迁移有利于副产物乙醇的生成，从而削弱了CO偶联主反应，\r\n催化剂表面活性组分Pd的相对含量减少，并几乎处于钝化状态，导致临\r\n氢反应中CO转化率、草酸二乙酯选择性及空时收率均下降．停止通入H\r\n2后，催化剂的活性可恢复至正常状态．     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n（Ce）／n（Zr）比为0．67／0．33,用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体,采用这些固溶体作载体,以Fe2O3为活性组分,用浸渍法制备了一系列催化剂,BET结果显示,将适量Ce0.67Zr0．33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积,TPR结果显示,载体中引入适量的Ce0．67Zr0.33O2可以改善催化剂的氧化还原性能,XRD结果表明,Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况,老化前后催化剂的晶相结构基本无明显变化,特别是当载体中m（Ce0.67Zr0.33O2）：m（Al2O3）的值为1：2时,Fe2O3／CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能。     

Ni/Al2O3催化剂上甲烷部分氧化制合成气反应CO2主要来源

负载型金属催化上甲烷催化部分氧化剂合成反应机理存在着燃烧－重整机理和直接氧化之争,如果反应按燃烧－重整机理进行,则ＣＯ２则是反应的一次产物而ＣＯ２是二次产物;如果反应按直接氧化机理进行,则ＣＯ是一次产物。本文采用同位素瞬变技术,对Ｎｉ／Ａｌ２Ｏ３催化上甲烷部分氧化制合成气反应中ＣＯ２的来源进行了研究,结果表明ＣＯ２同ＣＯ－样,主要来源于催化剂表面ＮｉＯ与甲烷分解生成的ＮｉｘＣ的反应,这就有力地证明     

Pt/Al2O3和Pt/CeO2/Al2O3催化甲烷部分氧化制合成气反应

研究了Pt/Al₂O₃和Pt/CeO₂/Al₂O₃对甲烷部分氧化制合成气反应的催化活性,发现Pt/CeO₂/Al₂O₃显示了更高的甲烷转化率和合成气选择性.用H₂-TPR、H₂-TPD、SEM-EDX和XRD等技术对催化剂进行了表征.CeO₂和Pt相互作用促进Pt在催化剂表面的分散,抑制Pt在催化剂表面的迁移;降低了催化剂的燃烧活性,提高了催化剂的部分氧化活性和选择性,可避免因催化剂床层局部温度过高而导致催化剂活性下降或失活,提高了催化剂的稳定性.同时,CeO₂通过促进水汽变换反应使反应体系迅速达到平衡,提高了催化剂对H₂的选择性.