Ba(Mg1/3Nb2/3)O3电子结构第一性原理计算及光学性能研究

Ba(Mg_1/3Nb_2/3)O₃ (BMN)复合钙钛矿陶瓷具有高介电常数和高品质因子等介电性能, 预示了其在光学领域的应用前景. 本文采用第一性原理方法计算了BMN的电子结构, 对其本征光学性能进行分析和预测. 对固相合成六方相BMN的XRD 测试结果进行Rietveld精修(加权方差因子R_wp=6.73%, 方差因子R_p=5.05%), 在此基础上建立晶体结构模型并对其进行几何优化. 运用基于密度泛函理论(DFT)的平面波赝势方法, 对六方相BMN晶体模型的能带、态密度和光学性质进行理论计算. 结果表明BMN的能带结构为间接带隙, 禁带宽度E_g=2.728 eV. Mg-O和Ba-O以离子键结合为主, Nb-O以共价键结合为主, 费米面附近的能带主要由O-2p和Nb-4d 态电子占据, 形成了d-p轨道杂化. 修正带隙后, 计算了BMN沿[100]和[001]方向上的复介电函数、吸收系数和反射率等光学性质. 结果表明, BMN近乎光学各向同性, 在可见光区, 其本征透过率为77%< T <83%, 折射率为1.91< n <2.14, 并伴随一定的色散现象. 实验测试结果与理论计算结果相吻合.     

铁电磁体Pb(Fe1/2Nb1/2)O3的磁电性能研究

对铁电磁体Pb(Fe_1/2Nb_1/2)O₃单晶样品中的 介电和磁性能进行了研究. 认为在其反铁磁相变点观察到的介电常数和损耗的异常来自于自发极化序和自旋序的相互作用 引起的磁电耦合. 磁矩与温度的关系曲线在Nel点以下的低温段呈上升趋势，测得的磁滞 回线证明有弱铁磁性出现. 对铁电磁体磁电相互作用的Monte Carlo模拟得到与实验类似的 结果. 关键词： 铁电磁体 1/2Nb_1/2)O₃')" href="#">Pb(Fe_1/2Nb_1/2)O₃ 磁电耦合 Monte Carlo模拟     

The transverse laser induced thermoelectric voltages in step flow growth （1- x）PD（Mg1/3Nb2/3）O3-xPbTiO3 thin films

This paper reports that the transverse laser induced thermoelectric voltages （LITV） axe observed for the first time in the step flow growth （1- x）PD（Mg1/3Nb2/3）O3-xPbTiO3 （PMN-PT, x = 0.20, 0.33, 0.50） thin films deposited on vicinal-cut strontium titanate single crystal substrates. Because lead magnesium niobate-lead titanate is a solid solution of lead magnesium niobate （PMN） and lead titanate （PT）, there are two types of signals. One is wide with a time response of a microsecond, and the other superimposed with the wide signal is narrow with a time response of a nanosecond. The transverse LITV signals depend on the ratio of PMN to PT drastically. Under the irradiation of 28-ns pulsed KrF excimer laser with the 248-nm wavelength, the largest induced voltage is observed in the 0.50Pb（Mg1/3Nb2/3）O3-0.50 PbTiO3 films. Moreover, the effects of film thickness, substrates, and tilt angles of substrates are also investigated.     

铁电磁体Pb(Fe1/2Nb1/2)O3的磁电性能研究

对铁电磁体Pb(Fe1/2Nb1/2)O3单晶样品中的介电和磁性能进行了研究. 认为在其反铁磁相变点观察到的介电常数和损耗的异常来自于自发极化序和自旋序的相互作用引起的磁电耦合. 磁矩与温度的关系曲线在Néel点以下的低温段呈上升趋势,测得的磁滞回线证明有弱铁磁性出现. 对铁电磁体磁电相互作用的Monte Carlo模拟得到与实验类似的结果.     

Laser-induced voltage effects in Ca3Co4O9 thin films on tilted LaAlO3（001） substrates grown by chemical solution deposition

Laser-induced voltage effects in c-axis oriented Ca3Co4O9 thin films have been studied with samples fabricated on 10 tilted LaAlO3(001) substrates by a simple chemical solution deposition method. An open-circuit voltage with a rise time of about 10 ns and full width at half maximum of about 28 ns is detected when the film surface is irradiated by a 308-nm laser pulse with a duration of 25 ns. Besides, open-circuit voltage signals are also observed when the film surface is irradiated separately by the laser pulses of 532 nm and 1064 nm. The results indicate that Ca3Co4O9 thin films have a great potential application in the wide range photodetctor from the ultraviolet to near infrared regions.     

Ti/Sn（1-x）IrxO2电极制备及电生活性氯特性

通过热分解法制备了Ti/Sn(1-x)IrxO2电极,应用SEM观察了电极的表面形貌,通过线性伏安法、循环伏安法等实验方法测试了电极的电化学性能。实验结果表明,Ti/Sn0.7Ir0.3O2电极具有较好的析氯活性;电解产生的活性氯浓度随电流密度的增加先增加后降低;升高电解温度不利于活性氯的产生。     

Pb(Sc_(1/2)Nb_(1/2))O_3中有序-无序转变和铁电相变的Raman光谱研究

采用wolframite前驱物法制备了Pb(Sc1/2Nb1/2)O3陶瓷。通过调节陶瓷烧结工艺,获得了三种具有不同B位离子有序度的PSN陶瓷。测量了三种陶瓷样品在室温至160°C范围内的Raman光谱随温度变化。结果表明,随着温度的升高,三种不同B位有序度的陶瓷样品中,Raman光谱中位于530 cm-1的F2g模的峰位和半峰宽分别在100°C,85°C和80°C发生了突变,表明陶瓷分别在100°C,85°C和80°C三个温度点发生了铁电-顺电相变。上述结论得到了介电温度谱测量数据的支持。     

退火氧压对YBa2Cu3O7-x薄膜中的激光感生热电电压效应的影响

测量了在不同氧压下退火生长的YBa₂Cu₃O_7-x(YBCO)薄膜中的激光感生热电电压(LITV)信号,发现随退火氧压的增大可使LITV信号的峰值有2—4倍的增强,并且变化趋势与薄膜热电势的各向异性随氧含量的变化规律相同.波长在473—808nm范围内的连续激光辐照,在5000Pa的氧压下退火生长的YBCO薄膜中探测到的LITV信号最大;而紫外脉冲激光辐照时,LITV信号的最大值出现在退火氧压为10⁵Pa 关键词： 2Cu₃O_7-x薄膜')" href="#">YBa₂Cu₃O_7-x薄膜 激光感生热电电压 各向异性的Seebeck系数 氧含量     

Transverse laser induced thermoelectric voltage effect in tilted La0.5Sr0.5CoO3 thin films

The transverse laser induced thermoelectric voltage effect has been investigated in tilted La_0.5Sr_0.5CoO₃ thin films grown on vicinal cut LaAlO₃ (1 0 0) substrates when films are irradiated by pulse laser at room temperature. The detected voltage signals are demonstrated to originate from the transverse Seebeck effect as the linear dependence of voltage on tilted angle in the range of small tilted angle. The Seebeck coefficient anisotropy ΔS of 0.03 μV/K at room temperature is calculated and its distorted cubic structure is thought to be responsible for this. Films grown on a series of substrates with different tilted angles show the optimum angle of 19.8° for the maximum voltage. Film thickness dependence of voltage has also been studied.     

Microstructures and microwave dielectric properties of La1-xBx(Mg0.5Sn0.5)O3 ceramics

The microwave dielectric properties of La_1-xB_x(Mg_0.5Sn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La_1-xB_x(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The X-ray diffraction patterns of the La_0.995B_0.005(Mg_0.5Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. A maximum apparent density of 6.58 g/cm³, a dielectric constant (ε_r) of 19.8, a quality factor (Q × f) of 41,800 GHz, and a temperature coefficient of resonant frequency (τ_f) of −86 ppm/°C were obtained for La_0.995B_0.005(Mg_0.5Sn_0.5)O₃ ceramics that were sintered at 1500 °C for 4 h.     

Ag掺杂的La0.67Pb0.33MnO3薄膜中激光感生热电电压效应

采用脉冲激光沉积法在倾斜LaAlO₃衬底上制备了Ag掺杂的La_0.67Pb_0.33MnO₃(LPMO)系列薄膜，发现该类薄膜中有激光感生热电电压(LITV)效应.随着掺Ag量x(x为Ag的质量与LPMO的质量之比)从0.00增加到0.10，LPMO薄膜中的LITV信号的响应时间先递减后递增，但始终小于未掺Ag的薄膜，掺Ag量x=0.06时响应时间最小.研究发现LPMO薄膜存在一个最佳厚度，在这一厚度下可使得LITV信号 关键词： 3薄膜')" href="#">LaPbMnO₃薄膜 激光感生热电电压 各向异性Seebeck系数 响应时间     

Effect of different annealing methods on ferroelectric properties of 0.95Pb(Sc0.5Ta0.5)O3-0.05PbTiO3 thin films

0.95Pb(Sc_0.5Ta_0.5)O₃-0.05PbTiO₃ thin films were prepared on LaNiO₃/SiO₂/Si substrate by radio frequency magnetron sputtering, and the films were annealed subsequently with repeated many times by two approaches: normal one-step rapid thermal annealing and innovative two-steps rapid thermal annealing. X-ray diffraction demonstrates that all the films were preferred (1 0 0) oriented and an appropriate repeat of annealing process can enhance perovskite phase of the films. Scanning electron microscopy suggests that the films treated by two-steps rapid thermal annealing show crack-free, uniform size grains and dense microstructure. Measurement of remnant polarization and leakage current dependence of electric field confirms that the films treated by two-steps rapid thermal annealing exhibit better ferroelectric properties than the films treated by one-steps rapid thermal annealing. The results reveal that microstructure plays an important role in enhanced ferroelectric properties of the 0.95Pb(Sc_0.5Ta_0.5)O₃-0.05PbTiO₃ thin films.     

铌镁酸铅-钛酸铅铁电阴极电子发射特性

研究了铌镁酸铅-钛酸铅铁电材料的铁电、介电性能对阴极发射阈值电压的影响, 以及铁电阴极发射电流与激励脉冲电压和抽取电压之间的关系, 并分析了其发射机理. 结果表明, 室温介电常数高、极化强度变化量大的弛豫铁电体0.9Pb(Mg_1/3Nb_2/3)O₃-0.1PbTiO₃具有较小的发射阈值电压; 铁电阴极电子发射与快极化反转和等离子体的形成有关; 由极化反转所致电子发射的自发射电流随激励脉冲电压的增大呈幂律增长关系, 其发射电流开始于激励脉冲电压的下降沿; 在抽取电压较大时, 发射电流随抽取电压的增大呈线性增长关系, 说明大电流主要取决于抽取电压; 其发射电流开始于激励脉冲电压的上升沿, 与“三介点”处的场增强效应和等离子体的形成有关; 当抽取电压为2500 V 时, 得到的发射电流幅值为210 A, 相应的电流密度为447 A/cm².     

Effects of strontium on the characteristics of Pb(Zr1/2Ti1/2)O3--Pb(Zn1/3Nb2/3)O3 ceramics

The dielectric and piezoelectric properties of pyrochlore-free lead zirconate titanate-lead zinc niobate ceramics were investigated systematically as a function of Sr doping. The powders of Pb_{(1? x )}Sr _x [0.7(Zr_{1 / 2}Ti_{1 / 2})–0.3(Zn_{1 / 3}Nb_{2 / 3})]O₃, where x?=?0–0.06 were prepared using the columbite-(wolframite) precursor method. The ceramic materials were characterized using X-ray diffraction, dielectric spectra, hysteresis and electromechanical measurements. The phase-pure perovskite phase of Sr-doped PZN--PZT ceramics was obtained over a wide compositional range. The results showed that the optimized electrical properties were also achieved at composition x?=?0.0, which were K _P?=?0.69, d ₃₃?=?670?pC?N^?1, P _r?=?31.9?µC?cm^?2 and ε_rmax?=?18600. Maximum dielectric constant values of the systems decreased rapidly with increasing Sr concentration. Moreover, with increasing Sr concentration dielectric constant versus temperature curves become gradually broader. The diffuseness parameter increased significantly with Sr doping. Furthermore, Sr doping has been shown to produce a linear reduction in the transition temperature (T _m)?=?294.1–12.7x°C with concentration (x). Sr shifts the transition temperature of this system at a rate of 12.7°C?mol^?1%.     

氧压对SrTiO3和SrNb0.2Ti0.8O3薄膜晶格参数的影响及激光感生热电电压效应

采用脉冲激光沉积技术制备了SrTiO₃和SrNb_0.2Ti_0.8O₃薄膜.X射线衍射分析表明在LaAlO₃(100)单晶平衬底上生长的SrTiO₃及SrNb_0.2Ti_0.8O₃薄膜是沿［001］取向的近外延生长.随着氧压在一定范围内逐渐增大,SrTiO₃薄膜的晶格参数减小,而SrNb_0.2Ti_0.8O₃薄膜的晶格参数先减小后增大.同时摸索出制备具有二维电子气超晶格(SrTiO₃/SrNb_0.2Ti_0.8O₃)_L的最佳氧压为1.0×10^-2Pa.另外在LaAlO₃(100)倾斜衬底上制备的SrNb_0.2Ti_0.8O₃薄膜中观察到激光感生热电电压效应. 关键词： 0.2Ti_0.8O₃薄膜')" href="#">SrNb_0.2Ti_0.8O₃薄膜 晶格参数 激光感生热电电压 脉冲激光沉积     

(Bi1-x Agx)2(Te1-ySey)3粉体的机械合金化制备及其放电等离子烧结体的热电输运特性

采用机械合金化制备了n型(Bi_1-xAg_x)₂(Te_1-ySe_y)₃合金粉体,对其进行XRD分析表明Bi,Te,Ag,Se单质粉末,经2h球磨后实现了合金化;SEM分析表明随着机械合金化时间延长粉体颗粒变得均匀、细小,颗粒尺寸在微米至亚微米数量级.采用放电等离子烧结制备了块体样品,研究了合金成分和球磨时间对热电性能的影响.结果表明材料的热电性能与掺杂元素有密切关系,Ag有利于提高功率因子和降低晶格热导率,球磨10h的(Bi_0.99Ag_0.01)₂(Te_0.96Se_0.04)₃合金粉末的烧结块体具有最大的功率因子和最低的晶格热导率,并在323K取得最高ZT值0.52. 关键词： 1-xAg_x)₂(Te_1-ySe_y)₃合金')" href="#">(Bi_1-xAg_x)₂(Te_1-ySe_y)₃合金 机械合金化 放电等离子烧结 热电性能     

Improving microwave dielectric properties of La2.98/3Sr0.01(Mg0.5Sn0.5)O3 ceramics with CuO additive

The microwave dielectric properties of CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were investigated with a view to their application in microwave devices. CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method. The X-ray diffraction patterns of CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics exhibited no significant variation of phase with sintering temperature. By adding 0.75 wt.% CuO, a dielectric constant of 20.07, a quality factor (Q × f) of 63,000 GHz, and a temperature coefficient of resonant frequency τ_f (−77.0 ppm/°C) were obtained when La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were sintered at 1500 °C for 4 h.