准相位匹配倍频系统的带宽性质研究

根据准相位匹配倍频原理,讨论了实现宽带二次谐波转换需要满足的条件.以周期性极化铌酸锂晶体和掺杂氧化镁（7mol%）周期性极化铌酸锂（7mol%MgO-PPLN）晶体为例,分别比较了0型（e+e→e）和Ⅰ型（o+o→e）两种准相位匹配情况下宽带高效二次谐波转换的特性.研究表明,对于7mol%MgO-PPLN晶体,同时满足准相位匹配条件和群速度匹配条件的中心波长和带宽向短波方向移动,且0型（e+e→e）准相位匹配情况下可以获得更大的带宽.     

准晶非线性光子晶体中二次谐波波长和温度调谐的研究

在八重准周期极化的铌酸锂非线性光子晶体中,通过调节基频光波长实现了多个波长的同时共线准相位匹配倍频,最高转换效率达36%.同时,测量了准晶非线性光子晶体中二次谐波转换效率随晶体温度以及入射波长的变化,结果表明二次谐波在长波处具有更宽的温度以及波长调谐带宽.该项研究对于准周期非线性光子晶体在实际工作中的运用具有重要的指导意义. 关键词： 准周期 非线性光子晶体 温度调谐 波长调谐     

Ⅰ型准相位匹配周期性极化铌酸锂倍频蓝光输出

在周期为14．5μm的周期性极化铌酸锂中,利用d31得到了一阶Ⅰ型EY^ωEY^ω-Ez^2ω(oo-e)准相位匹配蓝光二次谐波。在150C下,由114μJ抽运光,得到了52μJ,0．473μm倍频蓝光,对应于平均最大转换效率45．6%。制备了一阶和三阶周期分别为4．5μm和13．5μm的周期性极化铌酸锂。在EY^ωEY^ω-Ez^2ω(ee-e)准相位匹配0．473μm蓝光倍频中。150C下,分别得到了41．3%和19%的倍频转换效率。oo-e准相位匹配比传统的ee-e准相位匹配有较大的光栅周期,尤其在短波长区域倍频输出应用中,降低了周期性结构制作的困难,其较大的容许带宽在实验中提高了频率转换效率。实验结果表明了在周期性极化铌酸锂中准相位匹配倍频的偏振相关性。     

宽带准连续光纤激光在周期极化铌酸锂中倍频特性的研究

双包层光纤激光器和非线性光学材料(如周期性极化的铌酸锂晶体,PPLN)相结合,开辟了实用性非线性光学器件的一个新领域。研究了准相位匹配周期性极化反转铌酸锂晶体对宽带准连续光纤激光倍频的温度特性和频谱特性。在理论上,从准相位匹配相位失配关系出发,推导了晶体温度与抽运源中心波长的关系以及温度响应带宽,并和已报道实验结果进行了比较,二者符合得很好。此外,还推导了倍频周期极化铌酸锂晶体对抽运基频光源的响应谱线带宽。在实验上,采用长度20mm,极化周期6．5μm,厚度0．5mm的周期极化铌酸锂晶体光纤激光器准连续宽带输出进行了倍频,获得了在不同控制温度下的倍频光光谱,并对此进行了详细分析。     

I型准相位匹配周期性极化铌酸锂倍频蓝光输出

在周期为 14 .5 μm的周期性极化铌酸锂中 ,利用d3 1,得到了一阶I型EωYEωY-E2ωZ (oo-e)准相位匹配蓝光二次谐波。在 15 0℃下 ,由 114 μJ抽运光 ,得到了 5 2 μJ ,0 .4 73μm倍频蓝光 ,对应于平均最大转换效率 4 5 .6 %。制备了一阶和三阶周期分别为 4 .5 μm和 13.5 μm的周期性极化铌酸锂。在EωZEωZ-E2ωZ (ee -e)准相位匹配 0 .4 73μm蓝光倍频中 ,15 0℃下 ,分别得到了 4 1.3%和 19%的倍频转换效率。oo -e准相位匹配比传统的ee -e准相位匹配有较大的光栅周期 ,尤其在短波长区域倍频输出应用中 ,降低了周期性结构制作的困难 ,其较大的容许带宽在实验中提高了频率转换效率。实验结果表明了在周期性极化铌酸锂中准相位匹配倍频的偏振相关性。     

周期性极化铌酸锂晶体中半非共线型宽带光学参变放大理论研究

基于周期性极化铌酸锂晶体(PPLN)的准相位匹配光参变放大过程,通过倾斜周期极化铌酸锂晶体中极化域(极化光栅)一定角度,实现了介于共线匹配方式和非共线匹配方式之间的一种半非共线型准相位匹配方式,并以该匹配方式下的各光矢量几何关系得出相位匹配曲线,找到在特定抽运光和信号光波长下能获得宽带增益放大的周期极化长度。并研究其极化倾斜角度与温度特性。模拟计算表明,在合适的角度与温度条件下,该方式可以532 nm抽运光抽运的信号光在800 nm和1064 nm处均获得宽带光参变放大。     

准相位匹配PPLN倍频理论研究与优化设计

对准相位匹配周期性极化铌酸锂(PPLN)倍频进行了理论研究，并对聚焦高斯光束条件下的倍频耦合波方程进行了求解，给出了准相位匹配倍频转换效率公式，分析了晶体长度与聚焦程度的关系，在此基础上对倍频谐振腔进行了优化设计，以期获得最大的倍频转换效率.本结果对准相位匹配倍频器件的设计具有一定的指导意义. 关键词： 倍频 准相位匹配 周期性极化铌酸锂     

周期性极化铌酸锂晶体光参量振荡调谐与容差特性分析

研究了周期性极化铌酸锂晶体光参量振荡的工作机理,并讨论了其波长调谐特性与极化反转光栅周期、抽运光波长与晶体温度的关系.在此基础上,通过对相位失配因子求微分的方案,分析了光参量振荡的增益与光栅周期、抽运光波长与晶体温度的关系,以及光栅周期、抽运光波长与晶体温度容差的关系 关键词： 准相位匹配 周期性极化铌酸锂 光参量振荡     

一阶准相位匹配周期性极化铌酸锂倍频产生18 mW绿光连续输出

通过高压脉冲电场极化 ,制备了周期为 6 5 μm、长为 12mm、宽为 10mm、厚为 0 5mm的一阶准相位匹配周期性极化铌酸锂 ;由 1 1W连续 1 0 6 μmNd∶YAG激光器抽运 ,在 5°时产生了约 18mW、0 .5 32 μm的倍频连续绿光 ,其对应的二次谐波转换效率约为 1 6 % ,二次谐波的归一化转换效率约为 1 5 %cm- 1 W- 1 ,相当于 79%的周期性极化铌酸锂的理想非线性系数。测量了抽运光功率与倍频光功率的关系     

高功率宽调谐输出的多周期极化铌酸锂晶体光学参量振荡器

利用掺杂浓度为5 mol%的掺氧化镁多周期极化铌酸锂晶体实现了高效单谐振的准相位匹配光参量振荡器,所使用的周期极化铌酸锂晶体有6个周期,且以1 μm为间隔,从26.5~31.5 μm. 该光参量振荡器以脉宽为150 ns,重复频率为10 kHz的声光调Q Nd∶YAG激光器为泵浦源,且泵浦光波长为1.064 μm. 通过控制晶体的温度（50~200℃）以及改变晶体的极化周期（26.5~31.5 μm）,可由该光参量振荡器获得2.83~2.89 μm,3.10~3.38 μm,3.57~3.78 μm,3.95~4.12 μm, 4.28~4.46 μm,4.65~4.79 μm的闲频光连续调谐输出. 且当泵浦功率为8.15 W时,在闲频光输出波长为3.33 μm处,获得了最大输出功率2.17 W.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.