Sintering of Si3N4-Y2O3 Under Nitrogen Pressure

This study shows that the amount ofAl₂O₃ needed to form high density Si₃N₄-15Y₂-O₃ samples can be reduced by using high surface area Si₃N₄ powder and high N₂ overpressure (high sintering temperatures) during the sintering process. The reduction in AI₂O₃ content results in improved oxidation resistance of the sintered samples.     

The System Si3N4-SiO2-Y2O3

Subsolidus phase relations were established in the system Si₃N₄-SiO₂-Y₂O₃. Four ternary compounds were confirmed, with compositions of Y₄Si₂O₇N₂, Y₂Si₃O₃N₄, YSiO₂N, and Y₁₀(SiO₄)₆N₂. The eutectic in the triangle Si₃N₄-Y₂Si₂O₇-Y₁₀(SiO₄)₆N₂ melts at 1500°C and that in the triangle Si₂N₂O-SiO₂-Y₂Si₂O₇ at 1550°C. The eutectic temperature of the Si₃N₄-Y₂Si₂O₇ join was ∼ 1520°C.     

Densification of Si3N4-Y2O3/Al2O3 by a Dual N2 Pressure Process

Sintering studies of Si₃N4-Y₂O3/Al₂O₃ compositions indicated that increased densification could be produced using a dual N₂ pressure process. RT modulus of rupture values and microstructures were found to be similar to hot-pressed material. The technique should be adaptable to complex shaped Si₃N₄ bodies where high density and strength are required .     

Oxidation and Strength Retention of Monolithic Si3N4 and Nanocomposite Si3N4-SiC with Yb2O3 as a Sintering Aid

The oxidation behaviors of monolithic Si₃N₄ and nanocomposite Si₃N₄-SiC with Yb₂O₃ as a sintering aid were investigated. The specimens were exposed to air at temperatures between 1200° and 1500°C for up to 200 h. Parabolic weight gains with respect to exposure time were observed for both specimens. The oxidation products formed on the surface also were similar, i.e., a mixture of crystalline Yb₂Si₂O₇ and SiO₂ (cristobalite). However, strength retention after oxidation was much higher for the nanocomposite Si₃N₄-SiC compared to the monolithic Si₃N₄. The SiC particles of the nanocomposite at the grain boundary were effective in suppressing the migration of Yb³⁺ ions from the bulk grain-boundary region to the surface during the oxidation process. As a result, depletion of yttribium ions, which led to the formation of a damaged zone beneath the oxide layer, was prevented.     

High-Temperature Failure Mechanisms of Hot-Pressed Si3N4 and Si3N4/Si3N4-Whisker-Reinforced Composites

The high-temperature flexural strength of hot-pressed silicon nitride (Si₃N₄) and Si₃N₄-whisker-reinforced Si₃N₄-matrix composites has been measured at a crosshead speed of 1.27 mm/min and temperatures up to 1400°C in a nitrogen atmosphere. Load–displacement curves for whisker-reinforced composites showed nonelastic fracture behavior at 1400°C. In contrast, such behavior was not observed for monolithic Si₃N₄. Microstructures of both materials have been examined by scanning and transmission electron microscopy. The results indicate that grain-boundary sliding could be responsible for strength degradation in both monolithic Si₃N₄ and its whisker composites. The origin of the nonelastic failure behavior of Si₃N₄-whisker composite at 1400°C was not positively identified but several possibilities are discussed.     

Pressureless Sintering of Dense Si3N4 and Si3N4/SiC Composites with Nitrate Additives

The effect of aluminum and yttrium nitrate additives on the densification of monolithic Si₃N₄ and a Si₃N₄/SiC composite by pressureless sintering was compared with that of oxide additives. The surfaces of Si₃N₄ particles milled with aluminum and yttrium nitrates, which were added as methanol solutions, were coated with a different layer containing Al and Y from that of Si₃N₄ particles milled with oxide additives. Monolithic Si₃N₄ could be sintered to 94% of theoretical density (TD) at 1500°C with nitrate additives. The sintering temperature was about 100°C lower than the case with oxide additives. After pressureless sintering at 1750°C for 2 h in N₂, the bulk density of a Si₃N₄/20 wt% SiC composite reached 95% TD with nitrate additives.     

Microstructural Evolution of Gas-Pressure-Sintered Si3N4 with Yb2O3 as a Sintering Aid

Microstructural evolution of gas-pressure-sintered Si₃N₄ with Yb₂O₃ as a sintering aid was observed. Microstructures typical for in situ toughened Si₃N₄, i.e., large elongated grains randomly distributed in a fine matrix, were observed. However, the size of the elongated grains near the surface was much larger than that at the center, resulting in two distinct regions: an inner region and an outer region. The smaller the amount of Yb₂O₃ added, the larger the difference in the size of the elongated grains between the outer and inner regions. The difference between microstructures was diminished when 16 wt% Yb₂O₃ was added. The microstructural change with Yb₂O₃ content was attributed to the evaporation of Yb-containing liquid phase from the surface.     

Phase Relations and Stability Studies in the Si3N4-SiO2-Y2O3 Pseudoternary System

Composite powders were hot-pressed to determine the phase relations in the Si₃N₄-SiO₂-Y₂O₃ pseudoternary system. Four quaternary compounds, Si₃Y₂O₃N₄, YSiO₂N, Y₁₀Si₇O₂₃N₄, and Y₄Si₂O₇N₂, were identified. Studies of polyphase and single-phase materials in this system showed that these 4 compounds are unstable under oxidizing conditions. Materials within the Si₃N₄-Si₂N₂O-Y₂Si₂O₇ compatibility triangle precluded the unstable compounds, and are extremely resistant to oxidation.     

Crystallization of Ultrafine Amorphous Si3N4 During Sintering

Ultrafine amorphous Si₃N₄ powders were synthesized from laser-heated gases and cold-pressed into pellets for sintering experiments. At temperatures >1300°C, the powders crystallized with a concurrent, linearly proportional decrease in surface area. These powders densified on a local scale without additives or pressure.     

Phase Relations in the Si3N4-Rich Portion of the Si3N4–AlN–Al2O3–Y2O3

The phase relations in the Si₃N₄-rich portion of the Si₃N₄–AlN–Y₂O₃ rystem were investigated using hot-pressed bodies. The one-phase fields of β3 and α, the twophase fields of β+α, β+M (M=melilite), and α+M, and the three-phase fields of β+α+M were observed in the Si₃N₄-rich portion. The α- and β-sialons are not two different compounds but an allotropic transformation phase of the Si–Al–O–N system, and an α solid solution expands and stabilizes with increasing Y₂O₃ content. Therefore, the formulas of the two sialons should be the same.     

Hot Isostatic Pressing of Si3N4 Powder Compacts and Reaction-Bonded Si3N4

Hot isostatically pressed silicon nitride was produced by densifying Si₃N₄ powder compacts and reaction-bonded Si₃N₄ (RBSN) parts with yttria as a sintering additive. The microstructure was analyzed using scanning electron microscopy, X-ray diffraction, and density measurements. The influence of the microstructure on fracture strength, creep, and oxidation behavior was investigated. It is assumed that the higher amount of oxygen in the Si₃N₄ starting powder compared with the RBSN starting material leads to an increased amount of liquid phase during densification. This results in grain growth and in a larger amount of grain boundary phase in the hot isostatically pressed material. Compared with the hot isostatically pressed RBSN samples therefore, strength decreases whereas the creep rate and the weight gain during oxidation increase.