羧甲基纤维素钠修饰的聚氨酯泡沫制备磁性吸油材料

采用聚氨酯泡沫为模板,依次修饰羧甲基纤维素钠(CMC)、Fe~(3+),在惰性气氛中高温热处理反应,制备多孔结构的磁性吸油材料.用光学显微镜、扫描电子显微镜、红外吸收光谱、X-射线衍射、接触角等技术对材料进行表征.详细考察了加热反应温度、CMC浓度和Fe~(3+)浓度对材料吸油性能和磁性的影响规律.实验表明,当加热反应温度选择230°C,CMC浓度为0.3 wt%,FeCl_3浓度为0.1 mol/L时,材料吸油性能最佳,对正己烷、二甲苯、环己烷、甲苯、乙酸乙酯、氯仿、机油、原油等有机溶剂和油类分子的吸附容量为10倍左右.磁性多孔材料具有明显的亲油、疏水特性,水的接触角达115.9°,同时材料密度只有0.036g/cm~3,能够漂浮于水面,实现对水面有机溶剂的快速吸附.吸附后的材料在外界磁场控制下,能够通过磁分离方式从水面快速分离.该材料具有良好的循环利用性能,可重复使用20次以上,吸油性能仍然保持良好.     

木棉纤维接枝聚苯乙烯吸油材料的制备及性能

以过氧化苯甲酰为引发剂,制备了木棉纤维接枝聚苯乙烯吸油材料。考察了引发剂浓度、单体浓度、反应温度和反应时间等因素对吸油材料吸油性能的影响。红外光谱表明苯乙烯接枝到了木棉纤维分子骨架上。在引发剂浓度为1.77 mmol/L、单体浓度为0.16 mol/L、反应温度80°C和反应2 h的条件下,吸油材料有最大的吸油倍率,对...     

石墨烯及其复合材料吸油性能研究进展

石油化工产品在国民经济生活中占有重要地位,但在石油开采和运输过程中漏油事件频发,对海洋生态环境造成重大污染.物理吸附除油方式以其成本低、污染小、可回收利用、操作简单等优点得到广泛应用.传统吸附材料往往具有双亲性,选择吸附性较差,需要进行表面疏水处理.石墨烯凭借其超大比表面积和亲油疏水的特性引起广泛关注.重点综述了石墨烯...     

原位缩聚制备聚氨酯/碳纳米管复合泡沫材料

采用球磨方法制备了均匀分散的碳纳米管(CNTs)/聚丙二醇分散体系,解决了碳纳米管在高黏滞聚醚醇中的分散问题,进一步以水为发泡剂,采用两步的原位缩聚法制备了碳纳米管均匀分散的聚氨酯(PU)/碳纳米管复合泡沫材料.通过FTIR、SEM、压缩实验、亲水性实验等表征了材料的结构和性能.结果表明碳纳米管的加入使聚氨酯材料的压缩强度和保水率得到显著提高.     

水性聚氨酯的制备及其性能的研究

本文以琥珀酸酐与三羟甲基丙烷反应,制得了含有羟基和羧基的酯类亲水性单体,并以此单体与ＴＤＩ和ＰＰＧ－１０００反应,制得了含有羧基的聚氨酯预聚体,在三乙醇胺水溶液中分散得到了水性聚氨酯（简称ＷＰＵ）。本文对预聚体的溶剂种类和用量,对乳胶粒的大小及形状的影响进行了研究,确认溶剂的用量越大,乳胶的粒径就越小;以丙酮作溶剂,乳胶粒为棒状或橄榄球状,而以丁酮为溶剂,得到的乳胶粒为圆球状。通过改变亲水单体的用     

PHMG化学键合改性抗菌聚氨酯软质泡沫的制备及性能

通过一步法模塑发泡工艺,将聚六亚甲基胍盐酸盐(PHMG)键合到聚氨酯(PU)分子链上,制备了抗菌聚氨酯软质泡沫。通过红外光谱表征抗菌聚氨酯的化学结构,并用紫外光谱测试聚氨酯中PHMG的键合率,同时测试了聚氨酯的泡孔结构、力学性能、抗菌性能和防霉性能。结果表明,当PHMG的质量分数为0.5%时,聚氨酯中PHMG的键合率达到76.0%,对大肠杆菌和金黄色葡萄球菌的抑菌率均超过99.5%,其防霉等级为0级。     

水性聚氨酯荧光材料的制备及其荧光性能

将4-胺基-4′-(N,N-二苯基氨基)-1,2-二苯乙烯(ADAS)溶解于N,N-二甲基甲酰胺(DMF)中后分别以混合和接枝的方式引入水性聚氨酯,制备了不同软段和扩链剂的水性聚氨酯荧光材料(FWPU)。采用傅里叶变换红外光谱、荧光光谱表征了FWPU的结构和荧光性能。结果表明:水性聚氨酯的软段和扩链剂结构均可影响FWPU的荧光强度;与溶解同样浓度ADAS的DMF溶液相比,混合法制备的FWPU其荧光强度最大可以增加76倍,接枝法制备的FWPU最大可增加47倍。     

PVA-SiO_2复合物改性棉纤维及其吸油性能

首先以棉纤维为主要原材料,通过一步浸渍将聚乙烯醇-二氧化硅粒子(PVA-SiO_2)复合物涂覆在棉纤维表面;然后对其进行疏水改性,制得一种超疏水吸油材料。通过扫描电子显微镜(SEM)和水接触角(WCA)测试对改性纤维的表面结构及润湿性进行了分析表征。研究了PVA和SiO_2纳米粒子的质量分数对纤维吸油性能的影响,并评价了改性纤维的疏水性、润湿耐受性、吸油速率和重复使用性能。结果表明:棉纤维经过PVA-SiO_2复合物涂覆后具有稳定的超疏水性,吸油量比改性前显著提高,对正己烷、甲苯和氯仿的吸油量分别提高了47%、18.6%和26.2%。     

球型木质素碳化树脂的制备及性能研究

利用酸法制桨的木质素磺酸盐废液合成的球形木质素阳离子交换树脂,直接制备木质素碳化树脂;考察了碳化条件,运用电子显微镜,热重分析,Ｘ射线衍射等仪器对木质素碳化树脂的结构,碳化失重,孔结构,比表面和吸附量等性能进行了研究。     

活性碳纤维/聚氨酯泡沫复合载体的制备及其性能研究

将活性碳纤维与聚氮酯原料混合发泡,制备一种新型活性碳纤维/聚氨酯泡沫复合载体.活性碳纤维的加入提高聚氨酯泡沫的亲水性、孔隙率,改善了聚酯酯泡沫载体生物相容性、化学和生物稳定性 能,延长了聚氨酯泡沫的使用寿命.在活性碳纤维的添加量为3(wt)%～5(wt)%时效果最佳.     

Synthesis of CO2 Copolymer Based Polyurethane Foams

CO2-copolymer based polyurethane foams were synthesized and characterized in this paper. The foams were found to have higher strength and lower heat of combustion than the conventional polyether polyurethane foams. They may find wide applications in many fields.     

树莓状超疏水多孔复合棉纤维的制备及油水分离性能

基于聚多巴胺（PDA）的化学性质和树莓状纳米粒子的粗糙结构,以聚多巴胺包覆的棉纤维为基底,制备了具有多重粗糙度的树莓状超疏水多孔复合棉纤维材料.通过扫描电子显微镜观察树莓状超疏水多孔复合棉纤维表面的微观形貌,PDA-SiO₂纳米粒子稳定地固定在聚多巴胺涂覆的棉纤维表面.经过氟化改性的树莓状超疏水多孔复合棉纤维具有超疏水性,水接触角为158.2°,油接触角为0°.油/水分离实验结果表明,树莓状超疏水多孔复合棉纤维对己烷/水混合物的分离效率可达99.4%以上,使用20次后仍维持较高的分离效率.同时,其具有较高的溶剂吸附能力（13~34 g/g）、重复使用性及机械稳定性,吸油能力可与硅气凝胶相媲美.     

Silicon Oxycarbide Foams from a Silicone Preceramic Polymer and Polyurethane

Ceramic open-cell foams were obtained from a preceramic polymer (a silicone resin) and blown polyurethanes, by pyrolysis at 1200°C in nitrogen. Silicon carbide submicron powders were also added to the silicone resin to give SiOC + SiC composite foams. The morphology of the foams was dependent on the architecture of the blown polyurethanes. The crushing strength as well as the elastic modulus increased with increasing relative density, reaching values as high as 14 and 450 MPa, respectively. Some of the foams displayed an excellent thermal stability (resistance to oxidation in air and decomposition in inert atmosphere) up to elevated temperatures.     

Sorption-Photometric Determination of 1-Naphthol with Polyurethane Foams

Abstract

Two approaches to sorption-photometric determination of 1-naphthol in waters with application of polyurethane foams are offered. The first approach was based on sorption of a coloured 1-naphthol azoderivative, which was formed by the reaction with 4-nitrophenyldiazonium tetrafluoroborate (NFD). In the second variant, 1-naphthol is first sorbed by a polyurethane foam, and it is then transformed into a coloured azoderivative by sorbent treatment of a NFD solution. A coloured 1-naphthol azoderivative was determined immediately in the polyurethane foam using diffuse reflectance spectroscopy. Calibration graphs are linear in the interval of concentrations of 0.01 - 1 μg/ml. The analytical results indicated that a selective and sensitive analytical procedure could be easily applied to determination of 1-naphthol concentration in waters.     

Chemo- and Regioselective Additions of Nucleophiles to Cyclic Carbonates for the Preparation of Self-Blowing Non-Isocyanate Polyurethane Foams

Polyurethane (PU) foams are indisputably daily essential materials found in many applications, notably for comfort (for example, matrasses) or energy saving (for example, thermal insulation). Today, greener routes for their production are intensively searched for to avoid the use of toxic isocyanates. An easily scalable process for the simple construction of self-blown isocyanate-free PU foams by exploiting the organocatalyzed chemo- and regioselective additions of amines and thiols to easily accessible cyclic carbonates is described. These reactions are first validated on model compounds and rationalized by DFT calculations. Various foams are then prepared and characterized in terms of morphology and mechanical properties, and the scope of the process is illustrated by modulating the composition of the reactive formulation. With impressive diversity and accessibility of the main components of the formulations, this new robust and solvent-free process could open avenues for construction of more sustainable PU foams, and offers the first realistic alternative to the traditional isocyanate route.     

Optimization of Polyurethane Foams for Enhanced Stir Bar Sorptive Extraction of Triazinic Herbicides in Water Matrices

In this work, polyurethane foams (PU) were developed, characterized and applied as new generation polymeric phases for stir bar sorptive extraction (SBSE) using seven triazinic herbicides (simazine, atrazine, prometon, ametryn, propazine, prometryn and terbutryn) as model compounds in water matrices. Assays performed for PU synthesis and characterization demonstrated that seven formulations presented remarkable stability and excellent mechanical and chemical resistance, for which the P₆ formulation showed the best results. By performing systematic assays on 25 mL of water samples spiked at the 10 μg/L level, it was established that the best experimental conditions using stir bars coated with P₆ were an equilibrium time of 6 h (1250 rpm), 5% of methanol as organic modifier, followed by liquid desorption with methanol as back extraction solvent under ultrasonic treatment (20 min) and high performance liquid chromatography with diode array detection (SBSE(PU)-LD-HPLC-DAD). This methodology provided good recoveries (20.4-62.0%) and remarkable reproducibility (R.S.D. <7.0%). Furthermore, excellent linear dynamic ranges between 0.9 and 16.7 μg/L (r² > 0.9949) and detection limits (0.1-0.5 μg/L) at trace level were also achieved. The application of the proposed analytical approach to analyze triazinic herbicides in ground and superficial water matrices, showed remarkable performance and by using the standard addition methodology the matrix effects are negligible. By comparing the best PU formulation (P₆, 71 μL) with commercial stir bars coated with PDMS (126 μL), recoveries normalized to the polymeric volume up to five times higher (atrazine) were attained. The ability of PU foams to extract the more polar compounds rather than PDMS makes this polymer a very valuable contribution for SBSE.     

环氧丁羟型聚氨酯弹性体的制备与性能

以间氯过氧苯甲酸(mCPBA)为氧化剂对降解法制备的端羟基聚丁二烯(DHTPB)中的部分双键进行环氧化改性,通过控制mCPBA和双键的比例制得具有不同环氧率的环氧化端羟基聚丁二烯(EHTPB),经1H-NMR分析测试表明EHTPB的环氧率分别为5%、10%和15%,与设计值基本一致.进一步以EHTPB为多元醇、4,4'-二苯基甲烷二异氰酸酯(MDI)为异氰酸酯、1,4-丁二醇为扩链剂制备了环氧丁羟型聚氨酯弹性体(EPU),并对其性能进行了测试,研究结果表明:丁羟胶的环氧化改性对聚氨酯弹性体的力学性有着一定的提升作用,其杨氏模量和拉伸强度随环氧率的上升而提高,而断裂伸长率则随环氧率的上升有所下降;环氧丁羟型聚氨酯弹性具有优异的弹性恢复能力;环氧化改性后,聚氨酯弹性体的热稳定性有一定程度的提高;聚氨酯弹性体的玻璃化转变温度随环氧率的上升而升高.