TiO2一维纳米材料及其纳米结构的合成

本文对合成TiO₂一维纳米材料及其有序纳米阵列的阳极氧化法、模板法以及水热法进行了全面而系统的评述，着重介绍了它们的最新研究进展。阳极氧化法能制备牢固负载于基体上的TiO₂纳米管阵列，这有助于构筑TiO₂纳米结构及其在纳米器件上的应用；与多种制备技术如溶胶－凝胶工艺、电化学沉积以及原子层沉积等相结合，模板法可以合成出多种形貌的TiO₂纳米材料如纳米管、纳米线和纳米棒，并可以通过改变所用模板的微观尺寸来调控TiO₂一维纳米材料及其有序阵列的微结构参数；水热合成法可以制备出直径小且比表面积大的TiO2纳米管粉末。但从目前看来，该法还不能制备出牢固负载于基体上的有序纳米阵列。文章最后指出了TiO₂一维纳米材料及其有序纳米阵列合成中存在的问题及今后发展方向。     

NiO/MnO2分级纳米片阵列复合材料的制备与超电容性能

通过化学浴沉积和水热法在泡沫镍上制备了NiO/MnO₂分级纳米片阵列复合材料,XRD和SEM测试表明NiO纳米片垂直生长在泡沫镍上,交叉形成网状阵列结构;MnO₂纳米介孔泡沫进一步生长在NiO纳米片两侧,与NiO形成了壳核式的复合结构。循环伏安和恒流充放电测试发现,NiO/MnO₂分级纳米片阵列复合材料的电化学性能相比复合前得到明显改善,在1 A·g^-1的电流密度下,比电容提高至1 297 F·g^-1;2 A·g^-1下循环1 000次,比电容保持率高达97%,比电容和循环性能的改善是由于分级纳米片阵列复合结构方便了电解液传质,扩大了活性材料与电解液的接触,促进了赝电容反应,提高了NiO和MnO₂的结构稳定性。     

TiO2/P(VdF-HFP)杂化纤维微孔膜的制备及其电化学性能

用电纺法制备了TiO₂/P(VdF-HFP)(聚偏氟乙烯-六氟丙烯共聚物)杂化纤维微孔膜, 用SEM观察了杂化纤维微孔膜的形貌, 并测算了这类由超细纤维相互搭接而形成的微孔膜的孔隙率. 这种微孔膜吸附LiPF₆/EC-DMC-EMC(碳酸乙烯酯-二甲基碳酸酯-碳酸甲乙酯)电解质溶液后得到凝胶聚合物电解质膜. 用电化学方法测试了聚合物电解质膜的离子电导率、锂离子迁移数等参数, 并研究了TiO₂纳米晶的掺入对聚合物电解质电化学性能的影响. 结果表明, TiO₂的掺入降低了P(VdF-HFP)聚合物基体的结晶度, 改善了凝胶聚合物电解质的低温电化学性能.     

多孔氧化铝有序膜的制备研究

本文用阳极氧化法分别在硫酸和草酸电解液中成功制备出高度有序、具有纳米级孔洞的氧化铝有序阵列模板。采用饱和HgCl₂去除Al基体后,得到典型六方形结构的多孔Al₂O₃有序膜。通过改变氧化电压、氧化时间等条件使模板的孔径、孔深可调、膜厚度可控,并系统研究了对模板有序性、孔径、膜厚度等的影响因素,总结出制备Al₂O₃有序膜的最佳工艺。     

Bi2S3量子点敏化TiO2纳米阵列结构的制备及光电性能

利用水热法制备一维TiO₂纳米棒阵列,并采用化学浴沉积法(CBD)结合自组装技术在TiO₂纳米棒上敏化Bi₂S₃量子点,形成TiO₂/Bi₂S₃复合纳米棒阵列。系统研究了复合结构的表面形貌、晶体结构、光学及光电性能。结果表明:在修饰有三氨丙基三乙氧基硅烷自组装单分子膜(APTS-SAMs)的TiO₂纳米棒表面形成一层致密的Bi₂S₃量子点敏化层,这一技术的关键是含-NH₂末端的APTS-SAMs可有效促进Bi₂S₃的异相成核作用;Bi₂S₃的沉积时间对复合结构的光吸收及光电响应性能有决定性的影响,薄膜的光电流随着沉积时间呈先增加后减小的趋势,在沉积时间为20min时,光电流密度最大。这是因为随着沉积时间的增加,TiO₂纳米棒表面Bi₂S₃量子点密度增大,光吸收增加;而当沉积时间进一步延长时,Bi₂S₃在TiO₂纳米棒表面的大量负载而形成堆积和团聚,导致表面缺陷增多,光生电子复合几率增大,从而使光电流密度减小。     

Bi2S3量子点敏化TiO2纳米阵列结构的制备及光电性能研究

利用水热法制备一维TiO₂纳米棒阵列,并采用化学浴沉积法(CBD)结合自组装技术在TiO₂纳米棒上敏化Bi₂S₃量子点,形成TiO₂/Bi₂S₃复合纳米棒阵列.系统研究了复合结构的表面形貌、晶体结构、光学及光电性能.结果表明:在修饰有三氨丙基三乙氧基硅烷自组装单分子膜(APTS-SAMs)的TiO₂纳米棒表面形成一层致密的Bi₂S₃量子点敏化层,这一技术的关键是含-NH₂末端的APTS-SAMs可有效促进Bi₂S₃的异相成核作用;Bi₂S₃的沉积时间对复合结构的光吸收及光电响应性能有决定性的影响,薄膜的光电流随着沉积时间呈先增加后减小的趋势,在沉积时间为20 min时,光电流密度最大.这是因为随着沉积时间的增加,TiO₂纳米棒表面Bi₂S₃量子点密度增大,光吸收增加;而当沉积时间进一步延长时,Bi₂S₃在TiO₂纳米棒表面的大量负载而形成堆积和团聚,导致表面缺陷增多,光生电子复合几率增大,从而使光电流密度减小.     

溶胶-凝胶-水热晶化法制备锐钛矿TiO2纳米膜的耐蚀性能

以钛酸正丁酯为前驱体, 采用溶胶-凝胶-水热晶化法在不锈钢(SS)表面制备TiO₂纳米膜. 利用X射线衍射(XRD)、Raman光谱、场发射扫描电子显微镜(SEM)、原子力显微镜(AFM)和俄歇电子能谱(AES)表征了TiO₂纳米膜的晶型、表面形貌和表面化学组成. 通过极化曲线和电化学阻抗谱(EIS)研究了TiO₂纳米膜的耐蚀性能. 170 °C下水热晶化制备的锐钛矿TiO₂与450 °C焙烧制备的锐钛矿TiO₂的结晶度类似, 但两种TiO₂薄膜的表面结构存在明显差异, 水热晶化法制备的TiO₂纳米膜在3.5% (w) NaCl溶液中的耐蚀性能优于焙烧法制备的.     

Pt/g-C3N4/KB纳米复合催化剂的制备及其甲醇氧化性能

采用溶液中等离子放电法制备出了Pt纳米颗粒,用热氧化刻蚀和水热法成功的对石墨相氮化碳（g-C₃N₄）进行处理进而均匀吸附在科琴黑（KB）表面,最终制备出了Pt/g-C₃N₄/KB纳米复合催化剂。通过XRD分析,扫描电镜,透射电镜和电化学工作站探究了催化剂的组成、结构、颗粒大小以及电化学性能。Pt/g-C₃N₄/KB纳米复合催化剂展现出了良好的甲醇电氧化性能,性能的提升可能是由于g-C₃N₄良好的化学稳定性,N元素的存在改变Pt外层电子结构从而提高催化活性,这些因素提高了Pt的催化效率。     

纳米多孔结构镍基复合膜电极的电化学法制备及其电容特性

通过对电沉积法得到的Ni-Cu合金镀层进行电化学去合金化处理, 制备了纳米多孔结构金属镍膜. 采用循环伏安法对多孔金属镍膜在1 mol·L^-1 KOH溶液中进行阳极氧化处理, 获得了纳米多孔结构的镍基复合膜电极. 应用扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和电化学技术对所制备的膜电极的物理性质及赝电容特性进行了表征. SEM、XRD和XPS的测试结果表明, 所制备的纳米多孔结构镍基复合膜由Ni、Ni(OH)₂和NiOOH组成. 电化学实验结果显示, 该复合膜在20 A·g^-1的充放电电流密度下, 给出了578 F·g^-1的初始比电容; 在1000次充放电循环后, 它的比电容值为544 F·g^-1, 电容保持率为94%. 纳米多孔结构有利于KOH电解液的渗透, 从而促进反应物种在电极内部的传输; 纳米多孔的金属镍基体可以提高Ni(OH)₂膜的电子导电性; 纳米大小的Ni(OH)₂颗粒能够缩短质子的固相扩散路径. 上述因素是所制备的纳米多孔结构镍基复合膜电极具有优异赝电容特性的主要原因.     

CdTe/CdS共敏化TiO2电极材料的制备与光电性能

将电沉积法和化学浴沉积法结合,分别将CdTe和CdS量子点纳米晶材料引入到TiO₂纳米管阵列上制备CdTe/CdS量子点共敏化TiO₂光电极。利用扫描电镜、X射线衍射和X射线能量色散光谱等测试手段对所得样品的形貌、晶型和组分进行表征。在模拟太阳光照射条件下,通过电化学工作站测试其光电化学性能。研究结果表明,相对于单一量子点敏化CdS/TiO₂和CdTe/TiO₂光电极而言,共敏化CdTe/CdS/TiO₂光电极表现出更好的光电转化性能,短路电流密度和光电转换效率分别可以达到3.1 mA·cm^-2和1.85%。此外,采用电化学阻抗测试技术对材料性能提升的原因进行深入的探究。     

In-depth profile analysis of filled alumina and titania nanostructured templates by radiofrequency glow discharge coupled to optical emission spectrometry

The development of highly ordered and self-assembled magnetic nanostructures such as arrays of Fe or Ni nanowires and their alloys is arousing increasing interest due to the peculiar magnetic properties of such materials at the nanoscale. These nanostructures can be fabricated using nanoporous anodic alumina membranes or self-assembled nanotubular titanium dioxide as templates. The chemical characterization of the nanostructured layers is of great importance to assist the optimization of the filling procedure or to determine their manufacturing quality. Radiofrequency glow discharge (RF-GD) coupled to optical emission spectrometry (OES) is a powerful tool for the direct analysis of either conducting or insulating materials and to carry out depth profile analysis of thin layers by multi-matrix calibration procedures. Thus, the capability of RF-GD-OES is investigated here for the in-depth quantitative analysis of self-aligned titania nanotubes and self-ordered nanoporous alumina filled with arrays of metallic and magnetic nanowires obtained using the template-assisted filling method. The samples analysed in this work consisted of arrays of Ni nanowires with different lengths (from 1.2 up to 5 μm) and multilayer nanowires of alternating layers with different thicknesses (of 1–2 μm) of Ni and Au, or Au and FeNi alloy, deposited inside the alumina and titania membranes. Results, compared with other techniques such as scanning electron microscopy and energy-dispersive X-ray spectroscopy, show that the RF-GD-OES surface analysis technique proves to be adequate and promising for this challenging application.     

Electrodeposition of Fe70Pd30 nanowires from a complexed ammonium–sulfosalicylic electrolyte with high stability

A highly stable plating bath for the electrodeposition of Fe–Pd nanowires into nanoporous alumina templates has been developed. Complexing of both metal ions and exchanging Fe²⁺ by Fe³⁺ avoid chemical reduction of Pd ions and, therefore, undesirable deposition. By using a pulse potential mode and appropriate adjustment of deposition potentials homogeneously filled templates without surface deposits and nanowires close to the desired composition of Fe₇₀Pd₃₀ have been achieved. These alloy nanowires represent a key step towards nanoactuators based on magnetic shape memory alloys.     

Paired cell for the preparation of AgI nanowires using nanoporous alumina membrane templates

This communication describes a relatively new and simple method for the preparation of AgI nanowires using nanoporous alumina membrane templates which can be easily extended to prepare nanowires of many other materials.     

Synthesis of europium-doped zinc oxide micro- and nanowires

Single crystalline Eu³⁺-doped wurtzite ZnO micro- and nanowires were synthesized by a chemical vapor deposition method (CVD). The nanostructures were grown by autocatalytic mechanism at walls of an alumina boat. The structure and properties of the doped ZnO is fully characterized by X-ray diffraction (XRD), energy-dispersive X-ray spectrometry (EDX), scanning and transmission electron microscopy (SEM and TEM), and photoluminescence (PL) methods. The synthesis was carried out for 10 min giving vertically aligned nanowires with mean diameter of 50–400 nm and with length of up to several microns. The nanowires were grown along ±[0001] direction. The concentration of Eu³⁺ dopant in the synthesized nanowires was varied from 0.7 to 0.9 at %. The crystal structure and microstructures of the doped nanomaterials were discussed and compared with undoped ZnO. The photoluminescence spectra show that emission of doped samples were shifted towards orange-red region (2.02 eV) relative to undoped zinc oxide nanostructures (2.37 eV) due to Eu³⁺ intraionic transitions from ZnO/Eu.     

Nanocatalysts Fabricated by a Dealloying Method

Two types of nanomaterials with different morphologies are described in this article: nanoporous metals and titanate nanowires. Both materials are fabricated by a dealloying method. In the former case, the catalytic properties of nanoporous gold and palladium are exemplified by many chemical transformations. The reactions proceed without any support, stabilizer, or ligands. The catalyst can be easily recovered by a simple separation process and reused many times without significant loss of catalytic activity. In the latter case, the dealloying of Ti–Al alloy is described as a new fabrication method for producing ultrafine titanate nanowires. This method does not require high‐temperature conditions, which is advantageous for the construction of fine structures. The key to this process is achieving a fine dispersion of intermetallic TiAl₃ nanocrystals in the Al matrix in the mother alloy. The resulting nanowires exhibit remarkable Sr²⁺ ion‐exchange properties.     

Surface molecularly imprinted nanowires for biorecognition

Herein we present a novel method for preparation of surface molecularly imprinted size-monodisperse nanowires. The imprint molecule is immobilized on the pore walls of a silane-treated nanoporous alumina membrane. The nanopores are then filled with the monomer mixture, and the polymerization is initiated. The alumina membrane is subsequently removed by chemical dissolution, leaving behind polypyrrole nanowires with glutamic acid binding sites situated at the surface. These nanowires can be dissolved in aqueous media, and their applications therefore should be compatible with procedures in which biological antibodies might otherwise be used. For example, the analyte molecule can be tagged with various markers, such as fluorescence probes and enzymes, whereby the problem of steric hindrance is avoided. Furthermore, these surface-imprinted nanowires are likely suited for imprinting and recognition of large-molecular-weight peptides and proteins. Related work is currently being undertaken in our laboratory.     

TiO2纳米管的模板法制备及表征

TiO2纳米材料在太阳能的储存与利用、光电转换、光致变色及光催化降解大气和水中的污染物等方面具有广阔的应用前景,成为重点研究的课题之一[1～5].目前,以TiO2纳米粉体和纳米膜的研究较为普遍,而TiO2纳米管的报道不多.由于纳米管比纳米膜具有更大的比表面积,因而具有较高的吸附能力,可望提高TiO2的光电转换效率.模板法(包括多孔阳极氧化铝膜(PAA)、光刻蚀制备的纳米模板、聚碳酸酯纳米滤膜等)在制备导电聚合物、金属、碳、无机半导体等纳米管或线型材料方面已得到广泛应用[6～9],在这些模板中,PAA膜具有均匀分布的垂直于表面的相互平行的密集纳米孔,且孔径、孔间距、膜厚可以通过电化学手段加以控制[10～13].     

Overcoming Steric Hindrance in Aryl-Aryl Homocoupling via On-Surface Copolymerization

On-surface synthesis is a unique tool for growing low-dimensional carbon nanomaterials with precise structural control down to the atomic level. This novel approach relies on carefully designed precursor molecules, which are deposited on suitable substrates and activated to ultimately form the desired nanostructures. One of the most applied reactions to covalently interlink molecular precursors is dehalogenative aryl-aryl coupling. Despite the versatility of this approach, many unsuccessful attempts are also known, most of them associated to the poor capability of the activated precursors to couple to each other. Such failure is often related to the steric hindrance between reactants, which may arise due to their coplanarity upon adsorption on a surface. Here, we propose a copolymerization approach to overcome the limitations that prevent intermolecular homocoupling. We apply the strategy of using suitable linkers as additional reactants to the formation of fully conjugated polycyclic nanowires incorporating non-benzenoid rings.     

Conducting polymer nanostructures and their application in biosensors

Nowadays, functionalized conducting polymer nanomaterials have been received great attention in nanoscience and nanotechnology because of their large surface area. This article reviews various methods for synthesis of conducting polymer nanostructures and their applications in sensing materials, focusing on hard-template, soft-template and other methods and the formation mechanism of conducting polymer nanostructures by these methods. Conducting polymer nanostructures, such as nanotubes, nanowires, and nanoparticles, as sensing platforms for various applications are also summarized.     

Assembly of one dimensional inorganic nanostructures into functional 2D and 3D architectures. Synthesis, arrangement and functionality

This review will focus on the synthesis, arrangement, structural assembly, for current and future applications, of 1D nanomaterials (tubes, wires, rods) in 2D and 3D ordered arrangements. The ability to synthesize and arrange one dimensional nanomaterials into ordered 2D or 3D micro or macro sized structures is of utmost importance in developing new devices and applications of these materials. Micro and macro sized architectures based on such 1D nanomaterials (e.g. tubes, wires, rods) provide a platform to integrate nanostructures at a larger and thus manageable scale into high performance electronic devices like field effect transistors, as chemo- and biosensors, catalysts, or in energy material applications. Carbon based, metal oxide and metal based 1D arranged materials as well as hybrid or composite 1D materials of the latter provide a broad materials platform, offering a perspective for new entries into fascinating structures and future applications of such assembled architectures. These architectures allow bridging the gap between 1D nanostructures and the micro and macro world and are the basis for an assembly of 1D materials into higher hierarchy domains. This critical review is intended to provide an interesting starting point to view the current state of the art and show perspectives for future developments in this field. The emphasis is on selected nanomaterials and the possibilities for building three dimensional arrays starting from one dimensional building blocks. Carbon nanotubes, metal oxide nanotubes and nanowires (e.g. ZnO, TiO(2), V(2)O(5), Cu(2)O, NiO, Fe(2)O(3)), silicon and germanium nanowires, and group III-V or II-VI based 1D semiconductor nanostructures like GaS and GaN, pure metals as well as 1D hybrid materials and their higher organized architectures (foremost in 3D) will be focussed. These materials have been the most intensively studied within the last 5-10 years with respect to nano-micro integration aspects and their functional and application oriented properties. The critical review should be interesting for a broader scientific community (chemists, physicists, material scientists) interested in synthetic and functional material aspects of 1D materials as well as their integration into next higher organized architectures.