Miscibility in poly(vinyl chloride)/chlorinated poly(vinyl chloride) blends,and blends of different chlorinated poly(vinyl chlorides)

Blends of poly(vinyl chloride) with chlorinated poly(vinyl chloride) (PVC), and blends of different chlorinated poly(vinyl chlorides) (CPVC) provide an opportunity to examine systematically the effect that small changes in chemical structure have on polymer-polymer miscibility. Phase diagrams of PVC/CPVC blends have been determined for CPVC's containing 62 to 38 percent chlorine. The characteristics of binary blends of CPVC's of different chlorine contents have also been examined using differential calorimetry (DSC) and transmission electron microscopy. Their mutual solubility has been found to be very sensitive to their differences in mole percent CCl₂ groups and degree of chlorination. In metastable binary blends of CPVC's possessing single glass transition temperatures (T_g) the rate of phase separation, as followed by DSC, was found to be relatively slow at temperatures 45 to 65° above the T_g of the blend.     

Miscibility of segmented polyurethane/poly(vinyl chloride) blends

Miscibilities of segmented polyurethanes (SPUs) and poly(vinyl chloride) (PVC) or functionalized poly(vinyl chloride) (FPVC) were studied with dynamic mechanical analysis, differential scanning calorimetry, and X‐ray diffraction. Mechanical properties of the blends were also studied with tensile measurements. The miscibility of the blends depended greatly on the hard‐segment content of SPU and the existence of the functional groups. The combination of SPU with a low hard‐segment content and PVC with functional groups made the blend system miscible. Moreover, controlling the blend composition of SPU/FPVC allowed us to modify the mechanical properties of SPU, where the elongation at break was multiplied without a significant change in its tensile strength. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3022–3029, 2001     

Miscibility of C60-end-capped poly(ethylene oxide) with poly(vinyl chloride)

The miscibility of blends of single [60]fullerene (C₆₀)-end-capped poly(ethylene oxide) (FPEO) or double C₆₀-end-capped poly(ethylene oxide) (FPEOF) with poly(vinyl chloride) (PVC) has been studied. Similar to poly(ethylene oxide) (PEO), both FPEO and FPEOF are also miscible with PVC over the entire composition range. X-ray photoelectron spectroscopy showed the development of a new low-binding-energy Cl2p doublet and a new high-binding-energy O1s peak in FPEO/PVC blends. The results show that the miscibility between FPEO and PVC arises from hydrogen bonding interaction between the α-hydrogen of PVC and the ether oxygen of FPEO. From the melting point depression of PEO, FPEO or FPEOF in the blends, the Flory-Huggins interaction parameters were found to be −0.169, −0.142, −0.093 for PVC/PEO, PVC/FPEO and PVC/FPEOF, respectively, demonstrating that all the three blend systems are miscible in the melt. However, the incorporation of C₆₀ slightly impairs the interaction between PEO and PVC.     

Miscibility of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and poly(vinyl chloride) blends

The miscibility behaviour of biodegradable poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHB-HV) blended with poly(vinyl chloride) (PVC) was investigated by using differential scanning calorimetry, dynamic mechanical thermal analysis, Fourier-transform infra-red spectroscopy and a mechanical testing system. A blend of PHB-HV containing 8% HV (PHB-8HV) with PVC was immiscible, showing two separate T_g values in all compositions: whereas a blend of PHB-HV containing 18% HV (PHB-18HV) with PVC was miscible, showing a melting-point depression and a single T_g in the whole range of compositions. For the PHB-18HV/PVC system, the C-O-C stretching vibration at 1183 cm⁻¹ of PHB-18HV and the CHCl deformation at 1254cm⁻¹ of PVC were shifted, indicating that there exists a specific intermolecular interaction between the two components. In addition, as the PVC component was increased, tensile strength and Young's modulus were increased, while the inverse behaviour was observed in elongation at break.     

Miscibility enhancement on the immiscible poly (vinyl pyrrolidone) and poly (ethyl methacrylate) with poly (vinyl phenol)

The miscibility behavior of ternary blends of poly (vinyl phenol) (PVPh)/poly (vinyl pyrrolidone) (PVP)/poly (ethyl methacrylate) (PEMA) was investigated mainly with calorimetry. PVPh is miscible with both PVP and PEMA on the basis of the single T_g observed over the entire composition range. FTIR was used to study the hydrogen bonding interaction between the hydroxyl group of PVPh and the carbonyl group of PVP and PEMA at various compositions. Furthermore, the addition of PVPh is able to enhance the miscibility of the immiscible PVP/PEMA and eventually transforms it into a miscible blend, especially when the ratio between PVP/PEMA is 3:1, probably because of favorable physical interaction. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1205–1213, 2006     

Miscibility and thermal behavior of poly(vinyl chloride)/feather keratin blends

Various poly(vinyl chloride) (PVC)/feather keratin (FK) blends were prepared via a solution blending method in the presence of N,N‐dimethylformamide as a solvent. The miscibility of the blends was studied with different analytical methods, such as dilute solution viscometry, differential scanning calorimetry, refractometry, and atomic force microscopy. According to the results obtained from these techniques, it was concluded that the PVC/FK blend was miscible in all the studied compositions. Specific interactions between carbonyl groups of the FK structure and hydrogen from the chlorine‐containing carbon of the PVC were found to be responsible for the observed miscibility on the basis of Fourier transform infrared spectroscopy. Furthermore, increasing the FK content in the blends resulted in their miscibility enhancement. The thermal stability of the samples, as an important characteristic of biobased polymer blends, was finally examined in terms of their FK weight percentage and application temperature. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The solubility of vinyl chloride in poly(vinyl chloride)

The solubility of vinyl chloride monomer (VCM) in PVC powders has been studied by equilibrium vapor pressure and microbalance gravimetric techniques at temperatures from 30 to 110°C. At temperatures and VCM concentrations above the glass transition, the solubility closely follows the Flory-Huggins equation with χ = 0.98 and is independent of temperature and of the PVC type, molecular weight, or history. In the glassy state, the VCM solubility is higher than the Flory-Huggins value and shows pronounced dependence upon time and the PVC history. These results have been interpreted through the dual-mode sorption concept of Michaels, Vieth, and Barrie: Normal dissolution follows the Flory-Huggins relation, and the additional glassy-state solubility represents the contribution of a hole-filling process. Changes in solubility with time and sample history parallel well-known volume relaxation processes, indicating that vapor solubility measurements offer a direct and sensitive measure of the free-volume state of glassy polymers.     

Modification of poly(vinyl chloride). XIX. Electroplating of poly(vinyl chloride)

As a preliminary treatment in the PVC-electroplating procedure, treatment with dimethylformamide followed by sensitization leads to a finely roughened and a highly hydrophilic surface with reducing power. This is caused by the formation of an ionic complex compound between dimethylformamide and tin(II) chloride absorbed in the PVC surface. A much more finely and deeply etched surface which exhibits higher adhesion through the mechanical interlocking effect is obtained with the PVC blends containing the plasticizer with a low value of interaction parameter and with a solubility parameter approximate to that of PVC. Adhesion of the metal layer to the PVC surface thus obtained is improved about 1.5 times by thermal aging at 120°C for 20 min.     

Compatibility of plasticizers with poly(vinyl chloride)

The tendency of a plasticizer to resist exudation from poly(vinyl chloride) (PVC) under compressive stress, known technologically as “compatibility,” is treated in terms of a network model, the plasticized composition being thought of as a rubber crosslinked by crystallites. Compatibility is increased by increased solvency (Flory-Huggins χ) and decreased by increasing plasticizer molar volume. A large crosslink density and/or insufficient melting of crosslinks during processing (thermal history) also decreases compatibility. All commercial primary plasticizers are believed to be infinitely miscible with amorphous PVC. Phase separation which occurs is syneresis and not related to any phase diagram. Swelling tests for compatibility and swelling measurements on dilute PVC gels are described. Some general principles relating to gel formation and association in polymer solutions are also discussed.     

Dehydrochlorination of poly(vinyl chloride)

PVC has been dehydrochlorinated with alcoholic alkali in soution at 7°C for different lengths of time. At early stages of dehydrochlorination the dominant reaction is intramolecular removal of HCl and this gives rise to two intense Raman bands at ～ 1126 (ν₁) and ～ 1518 cm^?1 (ν₂) and following UV irradiation, to a quadruplet ESR spectrum. Increasing polyene sequence length and intermolecular removal of HCl at later stages of reaction alters the quadruplet signal to a singlet, shifts ν₁ and ν₂ to lower frequencies and increases the molecular weight. The presence of polyene units stiffens the chain and increases the elastic modulus. The T_g is, however, lowered slightly due to the removal of bulky chlorine atoms which relieves steric hindrance and dipole interaction between neighboring chains. The β-transition is also rendered less distinct.     

Degradation of poly(vinyl chloride)

The decomposition of poly(vinyl chloride) below 155°C has been examined by thermogravimetric analysis. Degradation is enhanced by irradiation with 1 MeV electrons. Later stages of isothermal weight loss for thermal and radiolytic decomposition follow 3/2-order kinetics and a similar reaction scheme is inferred. A free radical mechanism for dehydrochlorination involving allyl and polyenyl radicals is postulated.     

Blends of plasticized poly(vinyl chloride) and waste flexible poly(vinyl chloride) with waste nitrile rubber powder

Blends of poly(vinyl chloride) (PVC) with varying contents of plasticizer and finely ground powder of waste nitrile rubber rollers were prepared over a wide range of rubber contents through high‐temperature blending. The effects of rubber and plasticizer (dioctyl phthalate) content on the tensile strength, percentage elongation, impact properties, hardness, abrasion resistance, flexural crack resistance, limiting oxygen index (LOI), electrical properties, and breakdown voltage were studied. The percentage elongation, flexural crack resistance, and impact strength of blends increased considerably over those of PVC. The waste rubber had a plasticizing effect. Blends of waste plasticized PVC and waste nitrile rubber showed promising properties. The electrical properties and LOI decreased with increasing rubber and plasticizer content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1552–1558, 2004     

Miscibility and morphology of the poly(vinyl chloride)/styrene-acrylonitrile copolymer/poly(methyl methacrylate) ternary blend system

The phase equilibrium of the ternary system poly (vinyl chloride) (PVC)/styrene-acrylonitrile copolymer (77/23) (SAN)/poly (methyl methacrylate) (PMMA) was investigated using a combination of turbidity, scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) measurements. Both turbidity and DSC were used to determine room temperature ternary phase diagrams. The results are basically similar, but the formulation based on the DSC results and the presumed phase model would seem more reliable since it is possible that immiscible blends may well have different phases with similar refractive indices.     

Effect of compatibility between solvent and poly(vinyl chloride) on dechlorination of poly(vinyl chloride)

In this study, the use of diethylene glycol (DEG), triethylene glycol (TEG), n-C₁₀H₂₁OH, and ethylene glycol (EG) as solvents for NaOH in the dechlorination of poly(vinyl chloride) (PVC) was investigated. In the early reaction time, the degrees of dechlorination for DEG, TEG, and n-C₁₀H₂₁OH were notably higher than that for EG. Further, the high compatibility between PVC and the solvents was considered to result in the easy penetration of the solvent and OH⁻ into PVC particles, leading to the acceleration of dechlorination in the early reaction stage. An improvement of the dechlorination was actually observed for DEG and TEG compared with EG. The solvent with the best compatibility to PVC, n-C₁₀H₂₁OH, however, showed little improvement due to the formation of a protective polyene layer on the surface of the PVC particles.     

Modification of poly(vinyl chloride). XXXIV. Crosslinked poly(vinyl chloride) via paste-processing

A novel PVC-crosslinking technique using 6-dibutylamino-1,3,5-triazine-2,4-dithiol (DB) was applied for a paste processing to produce a crosslinked PVC product. The paste formulation recommended in the present study consisted of 100 parts of PVC (Zeon 121), 60 parts of dioctyl phthalate, 0.2 parts of MgO, and 6 parts of a 50% solution of DB-Na in butylcarbitol, which gave a highly crosslinked and transparent sheet with an excellent stability for thermal discolouring. The increasing viscosity behaviour of the paste during storage is explained by the effect of interparticle attracting forces of DB-Na which coordinates to the ether oxygen atoms in the glycol derivatives adsorbed on the surface of PVC particles. The increased viscosity can be reduced by addition of 3 parts of N-butyl-benzene-sulfonamide. The tension-distortion properties at elevated temperatures were remarkably improved at the crosslinked product compared with the uncrosslinked. The mechanical properties of the two crosslinked products produced via paste processing and roll-blending are compared in regard to the differences of the uniformity of crosslinking units.     

Chemically crosslinked poly(vinyl chloride)

The effect of mixing time, temperature, and thermal treatment on mechanical properties of crosslinked PVC is investigated. The tensile properties and gel content of crosslinked and uncrosslinked PVC molded samples are evaluated. The cured samples exhibited higher tensile strength and thermal stability than unmodified PVC.     

Wet poly(vinyl chloride) membrane

Wet, porous, and semipermeable poly(vinyl chloride) (PVC) membrane prepared from a binary system, PVC and dimethylformamide, by immersing in alcohols or ethers was studied. The pore dimensions of the wet PVC membrane were from 0.01 to 0.05 μm, calculated from hydrodynamic permeability by using experimental values such as water flux and water content. They agreed reasonably well with the dimension of the pores which prevented the protein passing through the membrane, observed by SEM photographs. Formation of the wet PVC membrane can be explained by slow phase separation and slow leaching of the casting solution immersed in alcohols and ethers such as methanol and ethylene glycol monomethyl ether.