Bimodal Sintering of Al2O3/Al2O3 Platelet Ceramic Composites

The sintering behavior of an Al₂O₃ compact containing uniformly dispersed Al₂O₃ platelets has been investigated. The results reveal a significant decrease in the sintering rate as well as the formation of voids and cracklike defects in the presence of nonsinterable platelets. The addition of a small amount (2 vol%) of tetragonal-ZrO₂ particles enhances the sintering rate, increases end-point density (∼99.5% of theoretical density) and prevents formation of sintering defects.     

Grain-Boundary Segregation and Final-Stage Sintering of Y2O3

The addition of ThO₂ to Y₂O₃ inhibits grain growth during sintering and allows the sintering process to proceed to theoretical density by maintaining a high diffusion flux of vacancies from the pores to the grain boundaries. The inhibition of grain growth is accomplished by the segregation of ThO₂ solute at the grain boundaries, causing a decrease in the grain-boundary mobility. The segregation of ThO₂ at the grain boundaries can be inferred from the results of the microhardness and grain-growth studies presented. Further evidence for segregation is provided by quenching experiments and surface activity experiments.     

Interfaces in Oriented Al2O3-ZrO2 (Y2O3) Eutectics

Oriented samples of Al₂O₃-ZrO₂ (Y₂O₃) eutectics consisting of an alumina matrix with zirconia dispersoids were grown by directional solidification. Preferred growth directions and epitaxial relations were determined from X-ray and electron diffraction analyses. Imaging of interfaces was performed by high-resolution transmission electron microscopy on oriented platelets. Semicoherent interfaces were observed with faceting along crystallographic planes of both phases.     

Defect Models for Sintering and Densification of Al2O3: Ti and Al2O3: Zr

A defect model proposed to explain the effect of titanium doping on the rate of sintering of Al₂O₃ is revised to fit the oxidizing conditions of the experiments. The model accounts for the observed change in sintering rate by a change from rate limitation by ions to rate limitation by electrons, but requires the presence of an unusually large concentration of acceptor impurities in the material. Models similar to the ones originally proposed account for the rate of densification of Al₂O₃:Zr by hot-pressing in vacuo, provided it is extended by including electronics defects.     

Hydrolysis and Dispersion Properties of Aqueous Y2Si2O7 Suspensions

The dispersion of aqueous γ-Y₂Si₂O₇ suspensions, which contain only one component but have a complex ion environment, was studied by the introduction of two different polymer dispersants, polyethylenimine (PEI) and polyacrylic acid (PAA). The suspension without any dispersant remains stable in the pH range of 9–11.5 because of electrostatic repulsion, while it is flocculated upon stirring due to the readsorption of hydrolyzed ions on the colloid surface. However, suspensions with 1 dwb% PEI exhibit greater stability in the pH range of 4–11.5. The addition of PEI shifts the isoelectric point (IEP) of the suspensions from pH 5.8 to 10.8. Near the IEP (pH_IEP=10.8), the stability of the suspensions with PEI is dominated by the steric effect. When the pH is decreased to acid direction, the stabilization mechanism is changed from steric hindrance to an electrosteric effect little by little. PAA also has the effect of reducing the hydrolysis speed via a "buffer effect" in the basic pH range, but the lack of adsorption between the highly ionized anionic polymer molecules and the negative colloid particle surfaces shows no positive effect on hydrolysis of colloids and on the stabilization of Y₂Si₂O₇ suspensions.     

Field-Assisted Densification of Superhard B6O Materials with Y2O3/Al2O3 Addition

B₆O is a possible candidate of superhard materials with a hardness of 45 GPa measured on single crystals. Up to now, densification of these materials was only possible at high pressure. However, recently it was found that Al₂O₃ can be utilized as an effective sintering additive, similar to the addition of Y₂O₃/Al₂O₃ that was used in this work. The densification behavior of the material as a function of applied pressure, its microstructure evolution, and the resulting mechanical properties were investigated. A strong dependence of the densification with increasing pressure was found. The material revealed characteristic triple junctions filled with amorphous residue composed of B₂O₃, Al₂O₃, and Y₂O₃, while no amorphous grain-boundary films were observed along internal interfaces. Mechanical testing revealed on average a hardness of 33 GPa, a fracture toughness of 4 MPa·m^1/2, and a strength value of 520 MPa.     

High-Temperature Strength and Fracture Toughness of Y2O3-Partially-Stabilized ZrO2/Al2O3 Composites

The temperature dependence of bending strength, fracture toughness, and Young's modulus of composite materials fabricated in the ZrO₂ (Y₂O₃)-Al₂O₃ system were examined. The addition of A1203 enhanced the high-temperature strength. Isostatically hot-pressed, 60 wt% ZrO₂ (2 mol% Y₂O₃)/40 wt% Al₂O₃ exhibited an extremely high strength, 1000 MPa, at 1000°C.     

Slow Crack Growth Behavior in Transformation-Toughened Al2O3-ZrO2(Y2O3) Ceramics

Significant increases in the critical fracture toughness (K _IC ) over that of alumina are obtained by the stress-induced phase transformation in partially stabilized ZrO₂ particles which are dispersed in alumina. More importantly, improved slow crack growth resistance is observed in the alumina ceramics containing partially stabilized ZrO₂ particles when the stress-induced phase transformation occurs. Thus, increasing the contribution of the ZrO₂ phase transformation by tailoring the Y₂O₃ stabilizer content not only increases the critical fracture toughness (K_IC) but also the K _Ia to initiate slow crack growth. For example, crack velocities ( v )≥10^–9 m/s are obtained only at K _Ia≥5 MPa.m^1/2 in transformation-toughened ( K _IC=8.5 MPa.m^1/2) composites vs K _Ia≥2.7 MPa.m^1/2 for comparable velocities in composites where the transformation does not occur ( K _IC=4.5 MPa.m^1/2). This behavior is a result of crack-tip shielding by the dissipation of strain energy in the transformation zone surrounding the crack. The stress corrosion parameter n is lower and A greater in these fine-grained composite materials than in fine-grained aluminas. This is a result of the residual tensile stresses associated with larger (≥1 μm) monoclinic ZrO₂ particles which reside along the intergranular crack path.     

Metastable Phase Formation in Plasma-Sprayed ZrO2 (Y2O3)–Al2O3

Rapidly solidified ZrO₂ (Y₂O₃)–Al₂O₃ powders were prepared by melting fine-particle aggregates in a high-enthalpy plasma flame and then rapidly quenching them in cold water or on a copper chill plate. To ensure complete melting and homogenization of all the particles before quenching, the water-quenching treatment was often repeated two or even three times. The resulting melt-quenched powders and splats displayed a variety of metastable structures, depending on composition and cooling rate. ZrO₂-rich material developed an extended solid solution phase, whereas eutectic material formed a nanofibrous or amorphous structure. Under high cooling rate conditions, the ZrO₂-rich material developed a nanocomposite structure ( t -ZrO₂+α-Al₂O) directly by melt-quenching, whereas, more typically, such a structure was developed only after postannealing of the as-quenched metastable material.     

Low-Temperature High-Pressure Consolidation of Amorphous Al2O3–15 mol% Y2O3

This study examined pressure consolidation of amorphous Al₂O₃–15 mol% Y₂O₃ powders prepared by co-precipitation and spray pyrolysis. The two amorphous powders had similar true densities and crystallization sequences. Uniaxial hot pressing was carried out at 450°–600°C with a moderate pressure of 750 MPa. The co-precipitated powder could be hot pressed to a maximum relative density of 98% and remained amorphous. Pressure adversely affected the densification of the spray-pyrolyzed powder by favoring an early crystallization of γ-Al₂O₃ phase at 580°C. Plastic deformation of the amorphous phase is believed to be responsible for the large densification of the amorphous powders.     

Oxidation-Induced Toughening and Strengthening of Y2O3/SiC Nanocomposites

Effects of oxidation on mechanical properties have been investigated for Y₂O₃/5 vol% SiC nanocomposite. The roomtemperature fracture strength and toughness substantially increased after oxidation around 900–1000°C for 5 h. On the other hand, little improvement was identified for specimens treated in an inert atmosphere under the same conditions. A TEM study of the oxidized specimen surfaces revealed formation of extensive residual strain contours around SiC nanoparticles. The improved strength and toughness could be caused by compressive surface stress, which was generated by volume expansion of the nanoparticles due to oxidation.     

Strength and Fracture Toughness of Isostatically Hot-Pressed Composites of Al2O3 and Y2O3-Partially-Stabilized ZrO2

Composites of Al₂O₃ and Y₂O₃ partially-stabilized ZrO₂ were isostatically hot-pressed using submicrometer powders as the starting material. The addition of Al₂O₃ resulted in a large increase in bending strength. The average bending strength for a composite containing 20 wt% Al₂O₃ was 2400 MPa, and its fracture toughness was 17 MN·w^−3/2     

Dynamic Fracture Characterization of Al2O3 and SiCw/Al2O3

The dynamic stress intensity factors, which were determined with newly developed bar impact facilities and a new data reduction procedure, for an Al₂O₃ ceramic and 29 vol% SiC_w/Al₂O₃ composite were virtually identical, thus indicating that the short SiC whiskers were ineffective under dynamic fracture. SEM studies revealed five distinct fracture morphologies with increased percentage area of transgranular fracture in both materials with rapid crack propagation. Also, the high dynamic stress intensity factor caused multiple microscopic crack planes to form and then join as the crack advanced.     

Effect of TiO2 on Initial Sintering of Al2O3

Alpha alumina with additions of TiO₂ sintered more rapidly than "pure" alumina. The rate of initial sintering increased approximately exponentially with titania concentration up to a percentage beyond which the rate of sintering remained approximately constant or decreased slightly with additional titania. The concentration which produces the maximum rate of sintering is thought to be the solubility limit of TiO₂ in Al₂O₃. For alumina particles larger than about 2 μm, the kinetic process was mainly grain-boundary diffusion. With smaller particles, volume diffusion increased. The "solubility limit" increased with decreasing particle size, indicating an excess surface concentration of TiO₂. The data may be interpreted in terms of a region of enhanced diffusion at the grain boundary that increases with TiO₂ concentration. With small alumina particles, this region is large enough to become a significant portion of the volume of the particle, and the small particles appear to sinter by volume diffusion kinetics, but the diffusion coefficient corresponds to an enhanced diffusion coefficient.     

Sulfanilic Acid: A Novel Consolidation Agent for Al2O3 in Aqueous Media

A new solidifying agent, 4-aminobenzene sulfonic acid (sulfanilic acid), is reported in this paper. The consolidation process and mechanism were followed using on viscoelastic, FTIR, SEM, and Hg porosimetry measurements. It was shown that the Al₂O₃ slurries with PAA-Na as dispersant exhibited a high degree of particle stabilization. After the addition of sulfanilic acid, we observed an exponential increase in the storage modulus ( G ') as a function of consolidation time. Correspondingly, Al₂O₃ slurries exhibited a transition from a viscous to an elastic state (in 62 min). FTIR analysis indicated that the consolidation process might follow two steps: first, the adsorption of sulfanilic acid on the Al₂O₃ particle surface; second, the acid–base interaction between the adsorbed PAA-Na molecules and the sulfanilic acid molecules. This interaction could possibly induce the formation of three-dimensional networks through a bridging or charge neutralization mechanism. The as-consolidated Al₂O₃ green samples were homogeneous, with the relative green density being 54.69%. Results showed that it was feasible to introduce sulfanilic acid for the consolidation of Al₂O₃ slurries in aqueous media.