半干法烧结烟气脱硫灰的氧化改性

半干法烧结烟气脱硫灰中含有大量CaSO_3,而CaSO_3对于脱硫灰的稳定性具有重要影响,限制了脱硫灰的处理和综合利用。为了解决该问题,采用低温静态氧化改性实验和高温动态焙烧改性实验,在掺加和不掺加催化剂条件下,对含CaSO_3的脱硫灰进行了氧化改性研究,并结合热重实验考察了半干法烧结烟气脱硫灰中CaSO_3的高温动态氧化改性效果。结果表明,在低温为45、75和90℃时,掺入不同催化剂对半干法烧结烟气脱硫灰中CaSO_3进行氧化改性2 h,效果依次为:MnO_2Fe_2O_3不掺催化剂V_2O_5,且CaSO_3的氧化率均低于2.2%;在不掺催化剂的条件下,在350℃以上焙烧30~60 min,CaSO_3的氧化率均可达到85%以上。结合热重分析结果发现,选择合适的焙烧温度和时间对提高CaSO_3的氧化率有重要作用。     

烧结烟气脱硫剂性能的研究

为了提高脱硫效率和合理利用烧结过程中产生的机头灰,在半干法烟气脱硫剂生石灰中,加入一定量的烧结机头灰作为脱硫催化剂。在测定机头灰与生石灰化学成分、粒度和比表面积的基础上,研究和分析了机头灰与生石灰的质量配比对于脱硫效率的影响。结果表明,脱硫剂与机头灰在粒径分布和比表面积上都较接近,但经过消化活化后的混合脱硫剂的比表面积明显增大。当机头灰添加量为脱硫剂质量的2%～5%时,脱硫效率提高了2%～3%。机头灰与生石灰的胶凝反应以及机头灰中Fe2O3的催化作用是主要的作用机理。     

脱硫灰中杂质对石灰石脱硫活性的影响

研究脱硫灰中杂质对石灰石脱硫活性的影响具有重要意义,采用烟气湿法脱硫用石灰石粉反应速率的测定方法,使用瑞士万通902智能电位滴定仪,分析了SiO2、Al2O3、Fe2O3、CaSO3与MgO等脱硫灰中5种杂质对石灰石脱硫活性的影响。结果表明,在实验浓度范围内,SiO2、Al2O3、CaSO3的加入在一定程度上促进了石灰石的溶解,而MgO、Fe2O3的加入在一定程度上抑制了石灰石的溶解。将脱硫灰与石灰石掺合作脱硫剂时,要综合考虑这5种杂质对石灰石溶出的影响,选择适宜的脱硫灰和石灰石掺合比。     

金属负载型催化剂对烟气脱硫性能的影响

介绍了国内外烟气脱硫催化剂的研究现状,研究了金属氧化物负载型催化剂对烟气脱硫性能的影响。以活性炭(AC)为载体,选用8种不同的金属硝酸盐作为浸渍液,采用等体积浸渍法制备金属氧化物负载型催化剂。以脱硫效果较好的Fe2O3/AC为例,研究了不同焙烧温度、金属负载量以及焙烧时间对催化剂脱硫性能的影响。实验结果表明,Fe2O3/AC催化剂脱硫率随着金属负载量的增加呈递增趋势,最优金属负载量为10.0%(质量分数);脱硫率随着焙烧温度的增加显著提高,最优焙烧温度为350℃;脱硫率随着焙烧时间的增加而提高,最优焙烧时间为3.0h。     

催化超临界水氧化对氨基苯酚

采用CuO/γ-Al2O3和MnO2/γ-Al2O3为催化剂、H2O2为氧化剂,在一连续流固定床反应器中进行了超临界水氧化对氨基苯酚实验.实验结果表明,CuO和MnO2催化剂对于对氨基苯酚的氧化降解具有显著的促进作用.对氨基苯酚的去除率随反应温度和压力的升高、停留时间的延长而提高,在24～26 MPa和400～450℃条件下,数秒钟内COD去除率可达到99%以上,催化剂CuO/γ-Al2O3的催化效果优于MnO2/γ-Al2O3.证明了催化超临界水氧化技术的高效性.     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9％ ～5.4％.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3％的系统脱硫效率整体高于含湿量为5％和4％的样品,最大值达93.56％.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3％的循环脱硫灰较含湿量为5％的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5％样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaS03干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

高活性脱硫剂脱硫工艺的实验研究

对以粉煤灰为原料制备的高活性脱硫剂进行了半干法烟气脱硫实验研究,考虑添加剂、脱硫剂加入量、反应温度、烟气流量工艺因素的影响时该活性脱硫剂的脱硫性能;实验结果表明,加入添加剂后,脱硫效率提高1.5%～8.1%;当烟气流量＜2 m3/min,钙硫比取1.5～2.0范围时,脱硫效率较高;一定范围内反应温度变化对脱硫效率影响不大.     

催化超临界水氧化对氨基苯酚

采用CuO／γ-Al2O3和MnO2/γ-Al2O3为催化剂、H2O2为氧化剂，在一连续流固定床反应器中进行了超临界水氧化对氨基苯酚实验。实验结果表明，CuO和MnO2催化剂对于对氨基苯酚的氧化降解具有显著的促进作用。对氨基苯酚的去除率随反应温度和压力的升高、停留时间的延长而提高，在24～26MPa和400～450℃条件下，数秒钟内COD去除率可达到99％以上，催化剂CuO／γ-Al2O3的催化效果优于MnO2／γ-Al2O3。证明了催化超临界水氧化技术的高效性。     

半干半湿法烟气脱硫主要影响因素分析

建立了半干法气流床烟气脱硫实验反应装置。实验研究了温度、绝对含湿量和飞灰对烟气脱硫的影响。烟气温度在65～130℃之间,绝对含湿量通过改变蒸汽量调节,在0%～10%之间,并且采用飞灰一次加入来模拟返灰,石灰与粉煤灰的比例分别为1∶3,1∶5和1∶8。结果表明,没有水蒸气加入时,温度的升高对脱硫效率影响不大,加入水蒸气后温度为68℃左右时,脱硫效率最高;65℃时,绝对含湿量在73%时脱硫效率最高;在T=68℃、Ca/S=12时,与不加粉煤灰的脱硫剂相比,利用石灰/粉煤灰=1∶8的混合脱硫剂时,脱硫效率提高了128%。     

半干半湿法烟气脱硫主要影响因素分析

建立了半干法气流床烟气脱硫实验反应装置。实验研究了温度、绝对含湿量和飞灰对烟气脱硫的影响。烟气温度在65～130℃之间，绝对含湿量通过改变蒸汽量调节，在0％～10％之间，并且采用飞灰一次加入来模拟返灰，石灰与粉煤灰的比例分别为1：3，1：5和1：8。结果表明，没有水蒸气加入时，温度的升高对脱硫效率影响不大，加入水蒸气后温度为68℃左右时，脱硫效率最高；65℃时，绝对含湿量在7．3％时脱硫效率最高；在T=68℃、Ca／S：1．2时，与不加粉煤灰的脱硫剂相比，利用石灰／粉煤灰=1：8的混合脱硫剂时，脱硫效率提高了12．8％。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

有机官能团对改性硅吸附微囊藻毒素的影响

考察了不同有机改性硅对微囊藻毒素LR(mLR)和LA(mLA)的等温吸附行为。结果表明,有机改性硅可有效吸附去除水体中<0.1×10-6(质量分数)的微囊藻毒素,并且吸附去除效果随表面改性官能团中碳原子数量的增加而增加;相同条件下,有机改性硅在微囊藻毒素异构体之间存在着一定的吸附选择性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.