Ag/TiO2纳米材料的制备和光致变色性能研究

 采用光催化还原法在不同温度热处理的TiO2薄膜表面沉积Ag纳米颗粒,制备了Ag/TiO2纳米薄膜材料。通过UV-Vis吸收光谱表征对比了不同温度热处理的TiO2对Ag粒子光催化沉积的影响,发现500℃退火处理TiO2薄膜较利于Ag纳米粒子的光催化沉积;在650 nm红色激光照射下,500℃退火处理的Ag/TiO2样品具有明显的光致变色现象,对此变色过程中涉及的机理进行了讨论,且发现随着Ag纳米颗粒光催化沉积时间的增长,Ag/TiO2薄膜光致变色的响应速率提高,但Ag纳米颗粒过多会抑制Ag/TiO2薄膜的变色响应速率。     

Au/SiO2纳米多层薄膜的制备及其性质表征

利用多靶磁控溅射技术制备了Au/SiO₂纳米颗粒分散氧化物多层复合薄膜.研究了在保持Au单层颗粒膜沉积时间一定时薄膜厚度一定、变化SiO₂的沉积时间及SiO₂的沉积时间一定而改变薄膜厚度时，多层薄膜在薄膜厚度方向的微观结构对吸收光谱的影响.研究结果表明：具有纳米层状结构的Au/SiO₂多层薄膜在560 nm波长附近有明显的表面等离子共振吸收峰，吸收峰的强度随Au颗粒的浓度增加而增强，在Au颗粒浓度相同的情况下，复合薄膜 关键词： 2纳米复合薄膜')" href="#">Au/SiO₂纳米复合薄膜 多靶磁控溅射 吸收光谱 有效介质理论     

脉冲激光沉积Ag:BaTiO3纳米复合薄膜及其光学特性

在MgO(100)基片上利用脉冲激光沉积技术制备了掺有Ag纳米颗粒的BaTiO₃复合薄膜.通过X射线衍射对薄膜的结构进行了表征,利用透射电子显微镜对Ag纳米颗粒的尺寸、形态进行了观测,X射线光电子能谱结果表明Ag呈金属态.在410—500nm范围内观测到了Ag纳米颗粒引起的等离子振荡峰,随着后处理温度和Ag颗粒浓度的增加,吸收峰发生红移,并出现了双峰现象. 关键词： 金属纳米复合薄膜 激光沉积 光吸收     

脉冲激光沉积Ag:BaTiO3纳米复合薄膜及其光学特性

在MgO(100)基片上利用脉冲激光沉积技术制备了掺有Ag纳米颗粒的BaTiO3复合薄膜.通过X射线衍射对薄膜的结构进行了表征,利用透射电子显微镜对Ag纳米颗粒的尺寸、形态进行了观测,X射线光电子能谱结果表明Ag呈金属态.在410-500 nm范围内观测到了Ag纳米颗粒引起的等离子振荡峰,随着后处理温度和Ag颗粒浓度的增加,吸收峰发生红移,并出现了双峰现象.     

不同厚度溅射Ag膜的微结构及光学常数研究

用直流溅射法在室温Si基片上制备了4．9nm-189.0nm范围内不同厚度的Ag薄膜，并用X射线衍射及反射式椭偏光谱技术对薄膜的微结构和光学常数进行了测试分析。结构分析表明：制备的Ag膜均呈多晶状态，晶体结构仍为面心立方；随膜厚增加薄膜的平均晶粒心潮6．3nm逐渐增大到14．5nm；薄膜晶格常数均比标准值（0．40862nm)稍小，随膜厚增加，薄膜晶格常数由0．40585nm增大到0.40779nm。250nm-830nm光频范围椭偏光谱测量结果表明：与Johnson的厚Ag膜数据相比，我们制备的Ag薄膜光学折射率n总体上均增大，消光系数k变化复杂；在厚度为4．9nm-83.7nm范围内，实验薄膜的光学常数与Johnson数据差别很大，厚度小于33．3nm的实验薄膜k谱线中出现吸收峰，峰位由460nm红移至690nm处，且其对应的峰宽逐渐宽化；当膜厚达到约189nm时，实验薄膜与Johnson光学常数数据已基本趋于一致。     

中空Ag纳米球壳的制备及性能表征

 以改性聚苯乙烯微球为模板,采用化学镀法在聚苯乙烯微球表面包覆一层银,在四氢呋喃溶液中将聚苯乙烯微球溶解,得到中空Ag纳米球壳。采用扫描电镜、透射电镜和X射线衍射仪对样品进行了表征及分析,并用紫外可见分光光度计研究了粒子的光学性质。实验结果表明：运用此法成功地制备出中空Ag纳米球壳的内径为250 nm,壁厚约为15 nm,并且成功地使纳米粒子的紫外吸收光谱由600 nm红移至900 nm左右,实现了在可见光至近红外光区调节Ag纳米结构的吸收峰。     

光电变色器件用纳米晶氧化钛薄膜的微结构与特性

纳米晶TiO2薄膜在光电变色器件中具有很重要的作用。它的微结构直接影响染料的吸附、光的散射以及电荷输运的特性。因此，探索TiO2薄膜的微结构(如粒径、表面形貌和厚度等)及光电性能是非常有意义的。采用电子束蒸发工艺制备了光电变色器件用纳晶TiO2薄膜，利用原子力显微镜、X射线衍射、俄歇电子能谱等手段对纳米晶TiO2薄膜的表面形貌、结晶状态及组分进行了分析。从理论上研究和讨论了纳米晶TiO2薄膜晶粒尺寸对光电性能的影响，并用量子限制效应解释了吸收光谱峰值波长随粒径减小而发生蓝移的现象。     

Au/SiO2纳米多层薄膜的制备及其性质表征

利用多靶磁控溅射技术制备了Au/SiO2纳米颗粒分散氧化物多层复合薄膜.研究了在保持Au单层颗粒膜沉积时间一定时薄膜厚度一定、变化SiO2的沉积时间及SiO2的沉积时间一定而改变薄膜厚度时,多层薄膜在薄膜厚度方向的微观结构对吸收光谱的影响.研究结果表明:具有纳米层状结构的Au/SiO2多层薄膜在560nm波长附近有明显的表面等离子共振吸收峰,吸收峰的强度随Au颗粒的浓度增加而增强,在Au颗粒浓度相同的情况下,复合薄膜光学吸收强度随薄膜厚度的增加而增强.但当金属颗粒的浓度增加到一定程度时,金属颗粒相互接触,没有观察到纳米层状结构,薄膜不显示共振吸收峰特征.用修正后的M-G(Maxwell-Garnett)理论对吸收光谱进行了模拟,得到了与实验一致的结果.     

掺Ag纳米颗粒的BaTiO3复合薄膜的非线性光学特性

通过准分子激光(XeCl,308 nm,20 ns)在MgO(100)单晶衬底上制备了不同掺杂浓度的Ag:BaTiO3纳米复合薄膜,通过X射线衍射和X射线光电子能谱对薄膜的结构和组分进行了表征.在430 nm和470 nm附近观测到了不同浓度Ag纳米颗粒引起的等离子体吸收峰,通过z扫描技术对复合薄膜的三阶非线性光学特性进行了测量,并对其光学非线性的增强机制进行了讨论.     

(Au,Ag)/Si复合纳米颗粒薄膜的微结构与光谱特性

采用复合靶共溅射方法制备了(Au,Ag)/Si复合纳米颗粒薄膜,分别采用Maxwell-Garnett理论和微分有效媒质(DEM)理论计算了Ag/Si复合薄膜的吸收光谱,实验测量结果与DEM理论计算更接近,讨论了(Au,Ag)/Si体系复合薄膜共振吸收峰宽化的微观机制. 关键词：     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.