液晶稳态和瞬态多波混频与非线性光学特性

在掺杂（～3%重量比）碳纳米管和光敏取向基团的向列态液晶薄膜（5μm厚）中，在使用Ar⁺(514.5nm)为激发光做前向多波混频实验时，观察到7级的自衍射和探测光He-N e(632.8nm )的多级衍射均呈多环状结构.高斯光束中心处的光致非线性折射率系数δn～0.8. Ar⁺ (514.5nm)连续光形成光栅的时间和弛豫时间都与写入光的偏振态强烈相关.在使用Nd :YAG（532 nm）为激发光时，光栅的弛豫时间～200ms量级，且探测光He-Ne(632.8nm)的o光和e光所探 测到的动力学响应曲线是不同的. 关键词： 瞬态 稳态 多波混频 液晶     

Zn∶Fe∶LiNbO_3晶体二波耦合和相位共轭效应的研究

采用二波耦合和四波混频实验,研究了Zn:Fe:LN(Fe:0.03wt.%,Zn:5.0mol)晶体的光折变二波耦合衍射效率和长时间照射下透射光强随时间的动态变化行为,以及其相位共轭效应,分别测试了其二波耦合衍射效率和其相位共轭反射率,结果表明该晶体的衍射率可达到56%,且其衍射效率随着其信号光的减小先增大后减小,相位共轭反射率随信号光的增大呈减小的趋势,最高共轭反射率可达到650%。     

Ce:KNSBN晶体中超短激光脉冲二波耦合和四波混频相位共轭

脉宽为50～60ps的超短激光脉冲列在Ce:KNSBN晶体中实现二波耦合和四波混频相位共轭。环境的微振动使二波耦合和四波混频相位共轭信号变得不稳定。当泵浦光脉冲从相对于探测光脉冲早到变为迟到时,二波耦合探测光信号从缩小变到放大。四波混频相位共轭信号出现双脉冲。晶体中存在纳秒光折变效应。     

掺杂C_(60)向列相液晶全息光栅衍射增强的研究

利用二波耦合(2BC)实验研究了掺杂G60垂直排列的向列相液晶(5CB)样品中形成光折变全息光栅的动态衍射特性.利用厚度为20μm的样品中记录的光折变全息光栅(光栅间距A≈24μm)获得了高达40%的一阶衍射效率,且衍射强度不对称分布.根据取向光折变效应体机制和表面电荷调制机制对此现象给出了解释,认为液晶中电场的增强是...     

向列型液晶中简并四波混频相位共轭的理论研究

研究向列型液晶中由光致分子重取向引起的简并四波混频光学相位共轭现象,着重讨论液晶薄膜厚度d、探测光与一泵浦光之间的夹角θ_ω以及光的入射面和液晶指向矢之间的夹角β对相位共轭光产生效率的影响.     

高非线性光纤中四波混频的磁控机理研究

将磁光效应和光纤非线性效应作为微扰,采用导波光耦合理论分析了高非线性光纤中导波光发生磁光四波混频的机理;实验测试了磁场对四波混频偏振依赖性的影响,理论分析与实验结果符合.研究表明,当输入的探测光和抽运光为相互正交的线偏振光时,四波混频的磁控效果最为明显,输出的闲频光功率随磁光耦合系数振荡变化,施加适当的外加磁场可使四波混频效率得到进一步提高.选择适当费尔德常数的光纤材料,利用磁光效应对四波混频偏振依赖性的影响,可实现不同范围的磁场测量.     

偶氮化合物中级联作用引起的高阶多波混频的研究

用三维简并四波混频的实验装置，在偶氮化合物中观察到了多波混频效应，在接收屏上，除了三个泵浦光斑，还观察到了由于多波耦合产生的另外１４个排列整齐的信号光斑，这个现象可望被广泛用光计算，信息处理和光互连中。     

飞秒激光在双折射微结构光纤中模式控制的四波混频效应的实验研究

利用飞秒激光脉冲在长度为10cm，包层具有大空气比的双折射微结构光纤中通过高阶模相位 匹配的四波混频获得了波长可调谐的反斯托克斯波.实验中脉冲宽度为35fs，中心波长820nm ，单脉冲能量4nJ的飞秒激光脉冲耦合到长轴直径为5μm，短轴为46μm的双折射微结构光 纤中.在高阶模传输情况下，通过调制耦合光的偏振方向，获得了具有不同中心波长的反斯 托克斯波.通过对比分析，讨论了输入光的偏振态对双折射微结构光纤中高阶模式下四波混 频效应的影响情况.理论计算分析很好的解释了实验结果. 关键词： 微结构光纤 飞秒脉冲激光 四波混频     

偶氮苯液晶薄膜相位共轭的光学记录研究

利用间并四波混频研究了一种偶氮苯液昌聚合物的相位共轭和光学记录特性，在近共振条件下，用低功率Ｎｄ：ＹＡＧ倍频激光得到高效率的相位共轭光和高阶衍射光，当光强达到１０Ｗ／ｃｍ＾２量级时，薄膜显示出光记录效应，即在撒掉写入光之后，相位共轭波并不消失，进一步大光强到１０＾３Ｗ／ｃｍ＾２量级时，出现三组分别只与前向泵浦光，后向泵浦光和信号有关的高阶衍射光。其中观察到第三阶衍射光，且在撒掉任两束光后，所剩一束     

冷~(85)Rb原子中的非共线非简并四波混频的实验研究

文章介绍了在磁光阱制备的Rb85冷原子团中通过特定时序的光场进行四波混频的实验研究,我们观察到了混频光强度的空间分布,简要讨论了三束作用光场的频率和光强对混频光产生的影响.时序调制下的四波混频实验为利用冷原子系综制备非经典关联光子对提供了基础.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.