双波长二极管合束端面抽运掺镨氟化钇锂单纵模360nm紫外激光器

报道了一种双波长半导体激光二极管(LD)合束端面抽运掺镨氟化钇锂晶体(Pr~(3+):LiYF_4)全固态、单纵模360nm紫外激光器.该激光器采用V形折叠腔结构,利用反射式体布拉格光栅作为波长选择反射镜来压缩光谱线宽,与法布里-珀罗(F-P)标准具组合构成窄带滤波器进行单纵模的有效选取,通过Ⅰ类位相匹配切割的倍频晶体三硼酸锂对腔内720nm基频光进行倍频.在444nmLD输出功率为1200mW和469nmLD输出功率为1400mW时,合束抽运获得了功率为112mW的连续单纵模360nm紫外激光稳定输出,光-光转换效率为4.3%.测量结果表明,边摸抑制比大于60dB,4h功率均方根值稳定性优于0.5%,1h频率漂移小于220MHz,激光振幅噪声小于0.5%.     

利用自相位延迟方法测量单块腔反馈半导体外腔激光器的线宽

提出了采用单块折叠法布里-珀罗(F-P)腔作为外腔反馈元件实现窄线宽半导体激光器,采用单块腔的光学反馈来锁定外腔激光器,使用自相位延迟法测量该窄线宽激光器的线宽。实验结果表明,激光器线宽小于35kHz。实验还观测到由于单块腔耦合面上各耦合点的几何量和物理量误差不一样,随着折叠面兼输入输出耦合面上的耦合点的变化,外腔激光器的线宽发生改变。     

F-P腔不同扫频段透射谱锁频精度实验

针对窄线宽激光器输出谱线窄,难以被锁定的情况,利用F-P腔特有极窄线宽、高精细度特性对激光器谱线线宽实施压窄及频率锁定。通过设计实验方案并搭建锁频测试平台,利用F-P腔外部光反馈将窄线宽半导体激光器线宽压窄来提高锁频精度。通过监测正弦波调制下F-P腔对于4种不同直流电压下激光PZT扫频段的透射谱线,并对其分别进行解调和锁频精度测试,得到直流高压放大器电压为73 V时对窄线宽激光器进行扫频,激光器反馈锁频精度最高可达1.5 MHz。     

基于自制超稳定F-P腔压窄632.8nm外腔半导体激光线宽的实验研究

窄线宽激光由于其具有单色性好、稳定度高、相干长度长等优点,广泛应用于光电检测领域,包括相干通信、精密测量、光学频率标准、吸收光谱计量以及光与物质相互作用研究等。目前频率稳定的氦氖激光器线宽可以达到MHz量级,分布反馈式（DFB）光纤激光器线宽可达kHz量级,DFB半导体激光器线宽可以达到MHz量级,然而光栅反馈半导体激光器可以实现百kHz量级线宽的输出。为了进一步压窄各类激光器线宽,需要通过反馈控制技术来锁定激光到某一频率参考。该研究将自行设计的超稳腔作为频率参考,实现了632.8 nm外腔半导体激光器（ECDL）线宽的有效压窄。本窄线宽激光产生系统的研制包括超稳腔设计、光路设计、ECDL频率控制以及系统集成。超稳腔采用两镜法布里-珀罗腔（F-P腔）结构,腔体是膨胀系数约为10-6 K-1的微晶玻璃,腔镜为一对反射率达99.988 5%(±0.003 5%）的平面镜和凹面镜。为进一步减小外界环境对F-P腔腔长的影响,需要对腔体进行温度控制,本系统采用四片总功率为96 W的半导体制冷片以及水冷散热设计。同时为了降低声音和空气流动对腔模频率的影响,将F-P腔置于真空度为10-5 torr的真空室中;另外为了有效隔振,腔体与真空室用硅橡胶材料隔离。该系统采用的ECDL为德国Toptica公司的DL pro系列激光器,其具有压电陶瓷（PZT）和电流调制两个频率控制端,响应带宽分别为1 kHz和100 MHz。激光器的频率控制采用了Pound-Drever-Hall （PDH）锁频技术,18 MHz的调制频率加载到激光器的电流调制端,通过对F-P腔的反射信号进行解调获得误差信号,通过两路反馈控制,实现了近1 MHz的锁定带宽。通过对系统的不断优化,最后将自由运转状态下约300 kHz的激光线宽压窄到了10 kHz量级,并且系统运行稳定,连续12小时锁定的频率漂移量约为30 MHz。该研究研制的632.8 nm窄线宽激光源不仅可以应用到吸收光谱计量领域,同时也可以在光学面型精密测量领域发挥重要作用。     

Short-term and long-term frequency characteristics of 2 μm single frequency Tm:YAG laser at room temperature

Placing one 0.1 mm YAG F-P etalon at nearly Brewster angle and combined use 1 mm fused silica in the cavity, a diode-pumped linear-polarized single-longitudinal-mode (SLM) Tm:YAG laser operating at 2 μm is achieved. This paper is focused on the stability of the linear-polarized SLM laser, including power stability, long-term frequency stability and short-term frequency stability. And the factors affecting the frequency characteristics of laser were also analyzed. The instability of the linear-polarization SLM laser is less than 1%. The long-term frequency stability is in the range from 1.16 × 10⁻⁷ to 1.75 × 10⁻⁷ monitored by the wave meter. And the short-term frequency stability is 97 Hz/μs measured with the self-beating heterodyne detection method.     

Diode-end-pumped linear-polarized single-frequency Tm:YAG laser at room temperature

By using two solid uncoated etalons, we present a diode-pumped linear-polarized single-frequency Tm:YAG laser operating at 2 μm. Placing one 0.1 mm F-P etalon at nearly Brewster angle in the cavity, the linear-polarization laser is achieved. The other 1 mm F-P etalon was turned in the range of very small angle, single-longitudinal-mode (SLM) could be obtained. The maximum output power of linear-polarized single-frequency laser of 60 mW is achieved at the wavelength of 2013 nm. The degree of the polarization is over 30 dB. Long-term frequency stability was also investigated, with the results of wavelength fluctuation about 2.55 × 10⁻¹³ m within 3 min and frequency change about 18.86 MHz, corresponding to a frequency stability of 1.27 × 10⁻⁷.     

激光二极管抽运的高输出单频稳频Nd∶YVO4激光器

研制了光纤耦合的激光二极管抽运的单频稳频Nd∶YVO4激光器。在输入抽运功率为 6W的情况下 ,获得 2W稳定单频红外输出 ,光光转换效率为 33 3% ,电光转换效率为 10 %。通过边带稳频系统将输出激光频率锁定在法布里珀罗共焦参考腔的中心频率上 ,频率稳定性优于 40 0kHz     

用157 nm激光制作的光子晶体光纤法布里-珀罗传感器

157nm准分子激光用于微加工具有单光子能量高,峰值功率高,材料吸收系数高,分辨率高等优点。利用157nm激光微加工的方法,在光子晶体光纤上融切出微小矩形孔,从而构成腔长为45.6μm的微光纤法布里-珀罗干涉腔,得到的干涉条纹平滑,衬比度约为26dB,并从激光与石英材料的相互作用上分析了形成较好干涉条纹的原因。把这种微腔应用于应变测量,在550μm范围内,腔长增量相对于应变的灵敏度为0.32nm/μm,线形度达0.9994。实验证明该微腔对温度不敏感,800℃范围内腔长变化仅20nm。157nm准分子激光加工光纤法布里-珀罗腔方法简单,一次成型,具有较高的加工效率和精度,有望实现光纤法布里-珀罗腔的规模化批量制造,具有较好的应用前景。     

Operating Parameter Comparison of Pulsed Optically Pumped NH3 and CH3OH F-P Cavity Far-Infrared Laser

Based on the density matrix theory of quantum system, the optimum operating parameters of pulsed optically pumped NH3 and CH3OH F-P cavity far-infrared laser (NH3/CH3OH-OPFIRL) were studied and compared theoretically. The differences of the operating parameters between the NH3-OPFIRL and CH3OH-OPFIRL were found and discussed. Experimentally, the curves of output power verses gas pressure in NH3 and CH3OH F-P cavity lasers pumped by TEA-CO2 laser were measured, and the optimum operating gas pressure were obtained. The experimental results were in agreement with theoretical calculations.     

利用稳频激光稳定F-P腔腔长的研究

为实现对F-P腔腔长的控制,设计了F-P腔腔长锁定控制系统。该系统以633nm稳频激光作为基准光源,通过控制系统驱动压电陶瓷调节F-P腔的腔长,以实现将F-P腔的谐振频率锁定到基准光源的频率上。实验结果表明,该方案切实可行,锁定后的F-P腔腔长的不确定度可达10-10量级。该方法在原子沉积技术中对于实现沉积台的稳定具有重要的指导意义。     

输出功率5.2 W的全固态连续单横模671 nm红光激光器

设计了全固态连续单横模671 nm红光激光器.利用880 nm LD双端端面泵浦Nd:YVO4复合晶体,实现了均匀泵浦并改善了激光晶体热效应;考虑到影响倍频转化效率的各种因素,优化设计了Z字形四镜激光谐振腔,采用I类临界相位匹配晶体LBO作为腔内倍频晶体;当泵浦功率为42.5W时,获得了5.2W的连续单横模671 nm红光输出,光-光转化效率达到12.2％,激光器长期功率稳定性优于±2.5％(1 h).     

Experiment Research on a Highly Stable LD-pumped Solid State Laser

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｈｉｇｈｐｏｗｅｒｌａｓｅｒｓｙｓｔｅｍｈｉｇｈｌｙｓｔａｂｌｅｓｏｌｉｄｓｔａｔｅｌａｓｅｒｉｓｖｉｔａｌｌｙｉｍｐｏｒｔａｎｔ.Ｈｏｗｅｖｅｒ,ｄｕｅｔｏｔｈｅｔｅｍｐｅｒａｔｕｒｅｆｌｕｃｔｕａｔｉｏｎｉｎｔｈｅＬＤｐｕｍｐｓｏｕｒｃｅａｎｄｔｈｅｌｅｎｇｔｈｆｌｕｃｔｕａｔｉｏｎｏｆｌａｓｅｒｒｅｓｏｎａｎｔｃａｖｉｔｉｅｓＬＤ ｐｕｍｐｅｄｓｏｌｉｄｓｔａｔｅｌａｓｅｒｓｈａｖｅｐｏｗｅｒｉｎｓｔａｂｉｌｉｔｉｅｓｏｆａｒｏｕｎｄ± 10 % .Ｗｉｔｈａｍｏ…     

Achieving single-longitudinal-mode output about Tm:YAG laser at room temperature

We report on the single-longitudinal-mode Tm:YAG laser with a volume Bragg grating pumped by laser diode at room temperature. The maximum SLM power of 142 mW was achieved under incident pump power of 3.22 W. The central wavelength was 2012.6 nm accords with the resonant wavelength of the VBG. Three cavity lengths were used to achieve high efficiency and clear spectrum. The maximum output power were measured to be 450.5, 451.4, and 457.3 mW at incident pump power of 3.22 W, corresponding to a slope efficiency of 17.1, 16.9, and 16.7% for the cavity length of 30, 40, and 50 mm, respectively. 40 mm cavity length having the cleanest spectrum among the three was used for SLM laser with one 1 mm F-P etalon inserted into the cavity.     

Experiment Research on a Highly Stable LD-pumped Solid State Laser

In high power laser systems, the stability of the seed laser is vitally important. This paper presents the work on the design and manufacture of a highly stable LD pumped solid state seed laser which has the advantages of being all solid state, compact, easy to manufacture and low cost. The laser was composed of two parts. One was an LD pumped 0.5 mm thin Nd: YLF laser system in which the instability was around±6% (3σ). The other was a close-looped laser power control system using external cavity power feedback. Using an electro-optic modulator, a 1×2 optical fiber splitter and a signal processing circuit, we successfully realized the highly stable LD pumped Nd: YLF laser in which the instability of laser output power was lower than±0.2 %/hour (3σ). A digital PID (Proportion, Integration and Differentiation) control method was used with a control frequency of 40 kHz. The 3 mW of highly stable laser power through the optical fiber was obtained.     

光泵THz激光器输出频率稳定特性研究

在太赫兹(THz)成像、雷达探测、相干通信等许多应用领域中,THz辐射源的频率稳定性是直接影响其应用效果的核心问题之一。基于双光子迁移效应建立了光泵THz激光器输出激光频率漂移的物理模型,推导出THz激光频率漂移的解析计算公式。以光泵甲醇(CH₃OH)为例, 给出了不同压强下的甲醇吸收谱线,定量分析了泵浦光频率漂移和泵浦功率对THz激光频率稳定性的影响,并讨论了THz激光腔内工作气体压强对THz激光频率漂移的影响。研究结果表明：随着泵浦光功率的增加,THz激光频率的漂移量逐渐增加;随着THz腔内工作气体压强升高,THz激光的频率漂移逐渐下降;当泵浦光频率漂移量在一定范围时,将出现THz激光的频率漂移量极值,且泵浦光的频率漂移量等于工作气体吸收谱线宽度的1/4时,THz激光输出的频率漂移达到极值。由此可见,在实际工作中,不仅需要合理选择腔内的工作条件(压强、温度),而且还需要采取措施将泵浦光的频率漂移控制在一定范围以内,以提高THz激光的输出频率稳定性。     

减敏控制光纤法布里-珀罗腔单值性用于解调振动频率

通过对光纤法布里-珀罗(Fabry-Perot cavity,F-P)腔单波长功率监测,对时域信号进行快速傅里叶变换(FFT),检测振动信号频率.建立了F-P腔的瞬时响应模型.发现透射响应比反射响应有微小延时,证明了F-P腔的多次反射原理对于一般频率不超过几十千赫兹的振动信号的测量没有影响.直接作用在F-P腔上的振动较强时,超过解调单值范围,波形发生畸变.通过增大振动源与F-P腔的距离控制解调单值性,当距离增至8 cm时,获得相对准确的解调结果.     

Frequency stabilization of a single-frequency all-solid-state laser for Doppler wind lidar

The master laser of an injection-seeded laser for Doppler wind lidar is frequency stabilized to a FabryPerot (FP) cavity using Pound-Drever-Hall technique. The FP cavity is specially designed to gain high temperature stability with Zerodur cavity and spacer. A computer based controller is used to sample and process the error signal. After the master laser is locked, the relative frequency drift is±25 kHz in 1 s,and ±55 kHz in 1 h, which can satisfy the need of Doppler wind lidar.     

High-power continuous wave green beam generation by use of simple linear cavity with side-pumped module

High-power continuous wave green radiation has been generated by means of type-II phase-matched frequency doubling in a KTP crystal located in a simple linear cavity incorporating a diode side-pumped Nd:YAG laser module. The cavity was designed to make the fundamental beam radius at the KTP crystal smaller than that at the gain medium, as is required for obtaining large mode volume in Nd:YAG crystal and realizing efficient CW intracavity frequency doubling. Output power of 51.2 W is obtained in the experiment with a diode-to-green optical conversion efficiency of 10.3%. The M²-parameters of the laser are measured at different output powers. For the output power of about 47 W, the power fluctuation is measured less than 1%. The experimental results show that the continuous wave green laser system using this simple linear cavity offers good laser performance and output stability.     

分布反馈激光器中剩余法布里-珀罗腔模对非简并四波混频特性的影响

基于四波混频(FWM)的全光波长转换技术是未来多波长通信系统的核心技术之一。除半导体光放大器(SOA)外,半导体激光器也是进行波长变换的器件。实验研究了小频率失谐到大频率失谐下分布反馈(DFB)激光器中剩余法布里珀罗腔模对非简并四波混频(NDFWM)的影响,并对其四波混频转换效率进行了分析。结果表明:当探测光波长与法布里珀罗腔的某一谐振波长一致时,分布反馈激光器中的四波混频转换效率将得到显著的增强;当频率失谐为太赫兹时,仍可得到较高的四波混频转换效率。     

2μm波段全光纤保偏被动锁模掺铥光纤激光器

报道了2μm波段的全光纤保偏锁模掺铥光纤激光器,通过在法布里-珀罗(F-P)腔内加入半导体可饱和吸收镜做为被动锁模器件,采用主振-放大构型,获得了最高输出平均功率为1.08W,重复频率为10.24MHz,脉冲宽度为15.24ps,中心波长为2054.68nm,光谱宽度约为0.3nm的2μm线偏振激光脉冲输出,激光脉冲的消光比为24.17dB。