Adhesion and permeability of polyimide–clay nanocomposite films for protective coatings

A polyimide (PI)–clay nanocomposite was prepared from a solution of poly(amic acid), a precursor of 2,2‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]propane dianhydride and p‐phenylenediamine, and dodecylamine–montmorillonite. Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, and atomic absorption spectroscopy were used to verify the incorporation of the modifying agents into the clay structure and the intercalation of the modified clay into the PI matrix. Both PI and PI–clay films were subsequently prepared by solution casting. The gas permeability, resistivity, and adhesion properties were determined. In the case of gas permeability, only a 3 wt % addition of clay reduced oxygen permeability to less than half that of unfilled PI. Furthermore, this hybrid showed an improvement in electrical resistivity because of the prevention of electrical tree growth by clay particles. More importantly, adhesion between the films and silicon increased with increasing clay content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2875–2881, 2003     

Preparation and properties of polyimide–clay nanocomposite materials for anticorrosion application

A series of polymer–clay nanocomposite (PCN) materials that consist of organosoluble polyimide and layered montmorillonite clay were prepared by the solution dispersion technique. The organosoluble polyimide containing non‐coplanar moiety in diamine monomer and flexible bridging linkages in dianhydride monomer was synthesized by chemical imidization. The as‐synthesized PCN materials were characterized by infrared spectroscopy, wide‐angle powder X‐ray diffraction, and transmission electron microscopy. The organosoluble polyimide showed better corrosion resistance compared to polyaniline, poly(o‐ethoxyaniline) and poly(methyl methacrylate) by using a series of standard electrochemical corrosion measurements of corrosion potential, polarization resistance, and corrosion current in 5 wt % aqueous NaCl electrolyte. Polyimide–clay nanocomposite materials incorporated with low loading of clay were found to further improve corrosion inhibition over pure polyimide. Effects of the material composition on the O₂/H₂O molecular permeability, optical clarity, and thermal properties of polyimide–clay nanocomposite materials were studied by molecular permeability analysis, UV–visible transmission spectra, thermogravimetric analysis, and differential scanning calorimetry, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3573–3582, 2004     

Preparation and properties of heterocyclically conjugated poly(3‐hexylthiophene)–clay nanocomposite materials

A series of heterocyclically conjugated polymer–clay nanocomposite (PCN) materials that consisted of organic poly(3‐hexylthiophene) (P3HT) and inorganic montmorillonite (MMT) clay platelets were prepared by in situ oxidative polymerization with FeCl₃ as an oxidant. The as‐synthesized PCN materials were characterized by Fourier transform infrared (FTIR) spectroscopy, wide‐angle powder X‐ray diffraction (WAXRD), and transmission electron microscopy (TEM). The effects of the material composition on the anticorrosion, gas barrier, thermal stability, flammability, mechanical strength, and electrical conductivity properties of the P3HT and PCN materials were studied by electrochemical corrosion measurements, gas‐permeability analysis (GPA), thermogrametric analysis (TGA), limiting oxygen index (LOI) measurements, dynamic mechanical analysis (DMA), and a four‐point probe technique, respectively. The molecular weights of extracted and bulk P3HT were determined by gel permeation chromatography (GPC) with THF as an eluant. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3438–3446, 2004     

Effective enhancement of anticorrosive properties of polystyrene by polystyrene–clay nanocomposite materials

A series of polymer–clay nanocomposite (PCN) materials consisting of polystyrene (PS) and layered montmorillonite (MMT) clay was prepared by effectively dispersing the inorganic nanolayers of MMT clay in the organic PS matrix via in situ thermal polymerization. Organic styrene monomers were first intercalated into the interlayer regions of organophilic clay hosts, followed by a typical free radical polymerization with BPO as the initiator. The as‐synthesized PCN materials were characterized by infrared spectroscopy (IR), wide‐angle powder X‐ray diffraction (XRD) and transmission electron microscopy (TEM). PCN coatings with low clay loading (1 wt %) on cold‐rolled steel (CRS) were found to be superior in anticorrosion to those of bulk PS, based on a series of electrochemical measurements of corrosion potential, polarization resistance and corrosion current in a 5 wt % aqueous NaCl electrolyte. The molecular weights of PS extracted from PCN materials and bulk PS were determined by gel permeation chromatography (GPC) with tetrahydrofuran (THF) as the eluent. The effects of material composition on molecular barrier and thermal stability of PS and PCN materials, in the form of both free‐standing films and fine powders, were also studied by molecular permeability analysis, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1970–1976, 2004     

Effect of clay on properties of polyimide‐clay nanocomposites

Effect of clay on mechanical, thermal, moisture absorption, and dielectric properties of polyimide‐clay nanocomposites was investigated. Nanocomposites of polyimide (ODA‐BSAA) hybridized with two modified clay (PK‐802 and PK‐805) were synthesized for comparison. The silicate layers in the polymer matrix were intercalated/exfoliated as confirmed by wide‐angle X‐ray diffraction and transmission electron microscopy. Thermal stability, moisture absorption, and storage modulus for these nanocomposites are improved as hybridized clay increases. Reduced dielectric constants due to the hybridization of layered silicates are observed at frequencies of 1 kHz–1 MHz and temperatures of 35–150°C. The tetrahedrally substituted smectite (PK‐805) resulted in higher mechanical strength and dielectric constants than those of octahedrally substituted smectite (PK‐802), which could be attributed to their stronger ionic bonding between clay layer and polymer matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 318–324, 2007     

Synthesis and dielectric properties of polystyrene‐clay nanocomposite materials

Polystyrene‐clay nanocomposite (PsCN) materials were synthesized and their properties of crystallinity, thermal behavior, and dielectric characteristics were investigated. A polymerizable cationic surfactant, [2‐(dimethylamino)ethyl]triphenylphonium bromide, was used for the intercalation of montmorillonite (MMT). The organophilic MMT was prepared by Na⁺‐exchanged MMT and ammonium cations of a cationic surfactant in an aqueous medium. Organophilic styrene monomers were intercalated into the interlayer regions of organophilic clay hosts followed by a free‐radical polymerization. Exfoliation to 2 wt % MMT in the polystyrene (PS) matrix was achieved as revealed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Thermal properties by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were also studied. The dielectric properties of PsCNs in the form of film with clay loading from 1.0 to 5.0 wt % were measured under frequencies of 100 Hz–1 MHz at 25–70°C. A decreased dielectric constant and low dielectric loss were observed for PsCN materials. The dielectric response at low frequency that originated from dipole orientation was suppressed due to the intercalation of clay materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1368–1373, 2004     

Organo‐soluble polyimde (ODA–BSAA)/montmorillonite nanocomposite materials prepared by solution dispersion technique

A series of polymer–clay nanocomposite materials, consisting of organo‐soluble polyimide (ODA‐BSAA) matrix and dispersed nanolayers of inorganic montmorillonite clay, were successfully prepared by solution dispersion technique and subsequently characterized by FTIR, powder X‐ray diffraction patterns, transmission electron microscopy, and atomic force microscopy. Effects of the materials composition on the corrosion protection performance, gas barrier, and optical properties, in the form of both coating and film, were also studied by electrochemical corrosion measurements (e.g., corrosion potential, polarization resistance, corrosion current, impedance spectroscopy), gas permeability analysis, and UV–visible transmission spectroscopy, respectively. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1082–1090, 2005     

Preparation,structure, and properties of a novel rectorite/styrene–butadiene copolymer nanocomposite

Rectorite/styrene–butadiene copolymer (SBR) nanocomposite was prepared by cocoagulating SBR latex and rectorite/water suspension. Transmission electron microscopy showed that the layers of rectorite were well dispersed in the SBR matrix and the aspect ratio (width/thickness) of it was higher than that of montmorillonite (MMT). X‐ray diffraction indicated that the nanocomposite produced by this method was of neither intercalated type nor exfoliated type. The gas barrier properties and mechanical properties of the novel nanocomposites were excellent. The nanocomposites are expected to be candidates for tire tube or inner materials. Rectorite appears to be a promising filler for the nanocomposite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 324–328, 2005     

Comparative studies of the properties of poly(methyl methacrylate)–clay nanocomposite materials prepared by in situ emulsion polymerization and solution dispersion

A series of polymer–clay nanocomposite (PCN) materials consisting of organic poly(methyl methacrylate) (PMMA) and inorganic montmorillonite (MMT) clay platelets were prepared successfully by the effective dispersion of nanolayers of the MMT clay in the PMMA framework through both in situ emulsion polymerization and solution dispersion. The as‐prepared PCN materials obtained with both approaches were subsequently characterized with wide‐angle powder X‐ray diffraction and transmission electron microscopy. For a comparison of the anticorrosion performance, a PCN material (e.g., 3 wt % clay loading) prepared by in situ emulsion polymerization, showing better dispersion of the clay platelets in the polymer matrix, exhibited better corrosion protection in the form of a coating on a cold‐rolled steel coupon than that prepared by solution dispersion, which showed a poor dispersion of the clay nanolayers according to a series of electrochemical corrosion measurements. Comparative studies of the optical clarity, molecular barrier properties, and thermal stability of samples prepared in both ways, as membranes and fine powders, were also performed with ultraviolet–visible transmission spectroscopy, molecular permeability analysis, thermogravimetric analysis, and differential scanning calorimetry. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1936–1946, 2004     

Effects of dispersion and arrangement of clay on thermal diffusivity of polyimide‐clay nanocomposite film

Polymer‐clay nanocomposites are well‐known high‐performance materials with a superior tensile modulus. However, in the case of composites with polyimide (PI), additional functions require study because PI is a high‐performance material in itself. Significant enhancement of thermal conductivity, which is closely related to the state of clay dispersion, is expected for a polymer‐clay nanocomposite. In this study, variations in the thermal diffusivity of PI‐clay nanocomposite films prepared by different methods were investigated. The thermal diffusivity of PI‐clay nanocomposite film increased at low clay content only when unmodified clay was used, where the clay morphology was a layered structure dispersed on a nanometer scale. Moreover, the thermal diffusivity could be enhanced by controlling the tensile stress induced by spontaneous shrinkage of the film during thermal imidization. These results demonstrated that the thermal diffusivity of PI‐clay nanocomposite films is significantly affected by the dispersion and/or arrangement states of the clay. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Polyacrylamide–clay nanocomposite materials prepared by photopolymerization with acrylamide as an intercalating agent

A series of nanocomposite materials consisting of water‐soluble polyacrylamide (PAA) and layered montmorillonite (MMT) clay platelets were prepared by the effective dispersion of the inorganic nanolayers of the MMT clay in the organic PAA matrix via in situ ultraviolet‐radiation polymerization. The acrylamide monomers functioned as both the intercalating agent and the reacting monomers. As a representative procedure for the preparation of the nanocomposites, organic acrylamide monomers were first intercalated into the interlayer regions of acrylamide‐treated organophilic clay hosts, and this was followed by one‐step ultraviolet‐radiation free‐radical polymerization with benzil as a photoinitiator. The as‐prepared polyacrylamide–clay nanocomposite (PCN) materials were subsequently characterized by Fourier transform infrared spectroscopy, wide‐angle powder X‐ray diffraction, and transmission electron microscopy. The effects of the material composition on the thermal stability, optical clarity, and gas‐barrier properties of pristine PAA and PCN materials, in the forms of fine powders and membranes, were also studied by differential scanning calorimetry, thermogravimetric analysis, ultraviolet–visible transmission spectroscopy, and gas permeability analysis. The molecular weights of PAA extracted from PCN materials and pristine PAA were determined by gel permeation chromatography with tetrahydrofuran as an eluant. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3489–3496, 2004     

High‐performance polyimide–clay nanocomposite materials based on a dual intercalating agent system

BACKGROUND: Polymer–clay nanocomposites (PCNs) have attracted considerable interest in recent years owing to their unique physical and chemical properties that lead to a wide range of applications. A series of PCN materials consisting of polyimide and layered montmorillonite (MMT) clay were successfully prepared by in situ polymerization. RESULTS: Silicate layers are better dispersed in polymer matrices when dual intercalating agents (hexadecyltrimethylammonium bromide–4,4′‐oxydianiline) are applied for MMT modification according to wide‐angle X‐ray diffraction and transmission electron microscopy studies. Effects of single and dual intercalating agents on thermal stability, mechanical strength and the molecular barrier of PCN materials consisting of organo‐modified MMT were studied by means of thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analyses, gas permeability analysis and vapor permeability analysis. CONCLUSION: Improved thermal and mechanical stabilities, as well as barrier properties were observed for the PCN materials containing dual intercalating agent‐modified MMT. Copyright © 2008 Society of Chemical Industry     

Preparation and properties of ethylene propylene rubber (EPR)–clay nanocomposites based on maleic anhydride‐modified EPR and organophilic clay

Ethylene propylene rubber–clay nanocomposites (EPR–CNs) were prepared by melt‐compounding maleic anhydride modified EPR (EPR‐MA) with organophilic clay, and their properties were examined. Silicate layers of organophilic clay were found to exfoliate and homogeneously disperse into the nanometer level in the nanocomposites by transmission electron microscopy observation. EPR–CNs exhibited higher tensile moduli compared to EPR‐MA and composites containing conventional fillers such as carbon black, talc. The storage moduli of EPR–CNs were also higher than those of EPR‐MA and the conventional composites. Creep resistances of EPR–CNs were much improved compared for EPR‐MA. Degree of swelling in hexadecane was remarkably restricted. Improvement of these properties is caused because dispersed silicate layers have much large interface with the EPR matrix and are thought to strongly restrain the EPR polymer chains. Nanocomposite technology using small amount of silicate layers is useful to improve properties of thermoplastic elastomer. Various kinds of thermoplastic elastomers are expected to be produced by loading of silicate layers with or without conventional fillers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 758–764, 2004     

Synthesis and properties of BCDA‐based polyimide–clay nanocomposites

Bicyclo[2.2.2]oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride (BCDA)‐based polyimide–clay nanocomposites were prepared from their precursor, namely polyamic acid, by a solution‐casting method. The organoclay was prepared by treating sodium montmorillonite (Kunipia F) clay with dodecyltrimethylammonium bromide at 80 °C. Polyamic acid solutions containing various weight percentages of organoclay were prepared from 4,4′‐(4,4′‐isopropylidenediphenyl‐1,1′‐diyldioxy)‐dianiline and BCDA in N‐methyl‐2‐pyrrolidone containing dispersed particles of organoclay at 20 °C. These solutions were cast on a glass plate using a Doctor's blade and then heated subsequently to obtain nanocomposite films. The nanocomposites were characterized using Fourier transform infrared spectroscopy, differential scanning calorimetry, thermal mechanical analysis, dynamic mechanical analysis, polarizing microscopy, scanning electron microscopy, transmission electron microscopy, wide‐angle X‐ray diffraction (WAXD) and thermogravimetric analysis. The glass transition temperature of the nanocomposites was found to be higher than that of pristine polymer. The coefficient of thermal expansion of the nanocomposites decreased with increasing organoclay content. WAXD studies indicated that the extent of silicate layer separation in the nanocomposite films depended upon the organoclay content. Tensile strength and modulus of the nanocomposite containing 1% organoclay were significantly higher when compared to pristine polymer and other nanocomposites. The thermal stability of the nanocomposites was found to be higher than that of pristine polymer in air and nitrogen atmosphere. Copyright © 2007 Society of Chemical Industry     

Enhanced corrosion prevention effect of polysulfone–clay nanocomposite materials prepared by solution dispersion

A series of polymer–clay nanocomposite (PCN) materials containing polysulfone (PSF) and layered MMT clay were successfully prepared by effectively dispersing inorganic nanolayers of MMT clay in an organic PSF matrix via a solution dispersion technique. The synthesized PCN materials were subsequently investigated with a series of characterization techniques, including Fourier transform infrared (FTIR) spectroscopy, wide‐angle powder X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The prepared PCN coatings with low clay loading (1 wt %) on cold‐rolled steel (CRS) were found to be superior in corrosion prevention to those of bulk PSF, based on a series of electrochemical measurements of corrosion potential, polarization resistance, corrosion current and electrochemical impedance spectroscopy (EIS) in a 5 wt % aqueous NaCl electrolyte. The effects of material composition on the molecular barrier, mechanical strength and optical clarity of PSF and PCN materials, in the form of membranes, was also studied by molecular permeability analysis (GPA), dynamic mechanical analysis (DMA) and UV‐Visible transmission spectra, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 631–637, 2004     

Synthesis and dielectric properties of poly(methyl methacrylate)–clay nanocomposite materials

Poly(methyl methacrylate) (PMMA)–clay nanocomposite (PCN) materials were synthesized through in situ intercalative polymerization. A cationic surfactant, [2(dimethylamino)ethyl]triphenylphosphonium bromide, was used as an intercalating agent with pristine Na⁺‐montmorillonite (MMT). The synthesized PCN materials were subsequently investigated by a series of characterization techniques, including wide‐angle powder X‐ray diffraction, Fourier transform IR spectroscopy, transmission electron microscopy, thermogravimetric analysis, and differential scanning calorimetry. Compared to pure PMMA, the PCN materials exhibit higher thermal degradation temperatures and glass‐transition temperatures. The dielectric properties of PCN blending with a commercial PMMA material in film form with clay loading from 0.5 to 5.0 wt % were measured under frequencies of 100 Hz–1 MHz at 35–100°C. Significantly depressed dielectric constants and losses were observed for these PCN‐blending materials. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2175–2181, 2005     

Structure and properties of poly(o‐methoxyaniline)–clay nanocomposite materials

In this study, we prepared a series of polymer–clay nanocomposite (PCN) materials that consisted of an emeraldine base of poly(o‐methoxyaniline) and layered montmorillonite. Organic o‐methoxyaniline monomers were first intercalated into the interlayer regions of organophilic clay hosts followed by a one‐step in situ oxidative polymerization. The as‐synthesized PCN materials were subsequently characterized by FTIR spectroscopy, wide‐angle powder X‐ray diffraction, and transmission electron microscopy. The molecular weights of PMA extracted from PCN materials and bulk PMA were determined by GPC with THF as eluant. Effects of the material composition on the thermal stability, flame resistance, electrical conductivity, and corrosion inhibition performance of PMA, along with a series of PCN materials in the form of fine powder and coating, were also studied by TGA, limiting oxygen index measurements, four‐point probe technique, and electrochemical corrosion measurements, respectively. Morphological images of as‐synthesized materials were also investigated by SEM. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1072–1080, 2003     

Rubber–clay nanocomposite by solution blending

Ethylene vinyl acetate rubber (45% vinyl acetate content, EVA‐45) and organomodified clay (12Me‐MMT) composites were prepared by solution blending of the rubber and the clay. A combination of X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy studies showed that the composites obtained are on the nanometer scale. The measurements of the dynamic mechanical properties for different compositions over a temperature range (?100 to +100°C) showed that the storage moduli of these rubber–clay nanocomposites are higher above the glass to rubber transition temperature compared to the neat rubber. The tensile strength of the nanocomposites is about 1.6 times higher than that of the EVA‐45. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2216–2220, 2003     

Rigid polyurethane–clay nanocomposite foams: Preparation and properties

Rigid polyurethane–clay nanocomposite foams considered in this work are made with different clay types and for different clay concentrations. The densities of the foams are in the range of 140–160 kg/m³ with possible application as structural materials and for underwater buoyancy‐related uses. Wide‐angle X‐ray diffraction and transmission electron microscopy studies confirm the formation of nanocomposites. The compressive modulus and the storage modulus of the foams increase and the mean cell size decreases with addition of clay. However, the hydraulic resistance of the nanocomposite foams, a measure of the strength of the foam lamellae, is lower than that of the foams without clay. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2802–2809, 2007     

Properties of poly(vinyl alcohol)—Bentonite clay nanocomposite films in relation to polymer–clay interactions

This study describes an effective way for the preparation of well‐dispersed, high‐loaded PVA/bentonite nanocomposites with improved properties, based on nanoscale interactions. To this end, a series of Poly(vinyl alcohol)—bentonite clay nanocomposites have been prepared via solvent casting technique and their properties were thoroughly investigated by atomic force microscopy, transmission electron microscopy, X‐Ray diffraction, oxygen and water permeability, water sorption along with mechanical and thermal studies. Microscopic and XRD techniques revealed highly organized regions. Clay content up to 10% led to nanocomposites with high degree of exfoliation. In addition samples with increased filler content (20%) demonstrated also, apart from the delaminated, well‐organized intercalated regions. The nanocomposites exhibited increased mechanical, thermal and gas barrier properties, though they retained their optical clarity. Thus, the Young's modulus of the sample containing 20% clay was increased by 193 times, while the oxygen permeability was decreased about seven times, in regard to the corresponding values of the neat polymer. The obtained results were explored on the basis of nanoscale phenomena and it was concluded that the organized structures and intercalated regions observed on highly loaded samples are attributed to the competitive effect between weaker polymer–polymer interactions in relation to stronger polymer–clay ones. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012