木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂对二元重金属离子溶液中Pb^2＋的吸附

采用自制木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂R1、R2、R3对二元金属离子Cu2＋/Pb2＋和Zn2＋/Pb2＋溶液中的吸附性能进行了较系统考察。Pb2＋离子溶液中存在竞争离子Cu2＋、Zn2＋时,随竞争离子浓度增加,3种吸附树脂R1、R2、R3对Pb2＋的吸附量明显下降,而竞争离子吸附量显著增加。二元溶液中各金属离子浓度相同时,3种树脂对竞争离子Cu2＋、Zn2＋的吸附量大于对Pb2＋的吸附量;各溶液中分别加入NaCl及NaNO3、尿素后,对Pb2＋离子的吸附量下降迅速。随吸附树脂用量增加,竞争离子Cu2＋、Zn2＋的吸附量逐渐减小,Pb2＋的吸附量在吸附树脂用量0.10 g/L（Zn2＋/Pb2＋溶液）或0.15 g/L（Cu2＋/Pb2＋溶液）时出现最大值。溶液pH值对树脂吸附性能有显著影响。3.0     

橘子皮皂化交联改性及其对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、NaOH和CaCl2处理,得到皂化交联改性橘子皮(SCOP)生物吸附剂,将其用于对重金属离子Cu2+、pb2+、Cd2+、Zn2+和Ni2+的吸附,并研究了溶液pH、吸附时间和重金属离子初始浓度对SCOP吸附性能的影响.结果表明,重金属离子在改性橘子皮上的吸附速率快,符合准二级动力学方程;改性橘子皮对Cu2+、pb2+、Zn2+和Ni2+的吸附等温线符合Langmuir方程,对Cd2+的吸附等温线符合Freundlich方程,根据Langmuir方程计算对Cu2+、pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为72.73、209.80、85.84、56.18、33.80mg/g,均高于改性前.改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂.     

三乙二醇二甲基丙烯酸酯为交联剂制备的高吸水树脂对重金属的吸附

以前期工作中合成的树脂PAANa-TE为吸附剂进行重金属吸附测试,考察吸附剂用量、丙烯酸中和度、吸附时间、溶液pH、初始浓度和吸附温度对树脂吸附重金属离子Cu2+、Pb2+、Cr3+和Co2+性能的影响,用原子吸收分光光度计测定了树脂吸附Cu2+、Pb2+、Cr3+和Co2+后的残留浓度,树脂对4种金属离子的吸附容量分别为21.59、2.39、5.66和4.98 mmol/g,吸附容量大小为Cu2+Cr3+Co2+Pb2+,吸附速率顺序为Cr3+Pb2+Cu2+Co2+。结果表明,该树脂对高浓度重金属离子有较快速,高效率的吸附,吸附过程在100 min左右吸附容量达到最大,并用不同浓度的酸对吸附重金属离子的树脂进行脱附处理,脱附量很小,据此可考虑进一步对金属离子进行回收处理。且脱附率较低,因此,可对工业化和城市化进程所产生的各种化学形态的重金属水体污染物造成的生态环境和质量问题起到重要的改善作用。     

皂化改性橘子皮生物吸附剂对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、氢氧化钠处理,得到改性橘子皮生物吸附剂SOP,将其用于对重金属离子Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的吸附。研究了溶液pH、吸附时间和重金属离子初始浓度对SOP吸附性能的影响。结果表明,重金属离子在生物吸附剂上的吸附速率快,符合准二级动力学方程。SOP对重金属离子的吸附等温线符合Lang-muir模型,根据Langmuir模型计算SOP对Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为56.82、152.4、66.27、33.90和23.02 mg/g,均高于改性前。常见阳离子的存在对重金属离子吸附的影响较小,改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂。     

重金属离子在钠基膨润土中的吸附特征与机理

膨润土是一种天然粘土矿物,比表面积大、吸附能力强。通过钠基膨润土对复合重金属离子Cu2+、Zn2+和Cd2+的竞争吸附实验研究,探讨了钠基膨润土对Cu2+、Zn2+和Cd2+的吸附特征。结果表明,钠基膨润土对Cu2+、Zn2+和Cd2+的吸附随离子浓度增加而增大。吸附具有选择性,Cu2+、Zn2+和Cd2+的吸附能力大小顺序为Cu2+>Zn2+>Cd2+。并通过XRD及IR等分析探讨了钠基膨润土的吸附机理主要表现为离子交换吸附。     

改性甘蔗渣对Cu2+和Zn2+的吸附机理

研究了均苯四甲酸二酐(PMDA)和乙二胺四乙酸二酐(EDTAD)改性甘蔗渣对重金属离子Cu2+和Zn2+的吸附性能,包括吸附动力学和吸附等温线。结果表明,改性后的甘蔗渣对重金属离子Cu2+和Zn2+的吸附容量有显著提高,对Cu2+和Zn2+吸附等温线均符合Langmuir方程,吸附为单分子层吸附。根据Langmuir方程,PMDA和EDTAD改性甘蔗渣对Cu2+的吸附量分别为60.21和33.45 mg/g,对Zn2+的吸附量分别是70.53和36.53 mg/g。两种改性甘蔗渣对两种金属离子的吸附在30 min内均可完成,用准二级吸附动力学方程模拟动力学过程得到较好的线性相关性。以EDTA溶液为洗脱剂对吸附Cu2+和Zn2+的改性甘蔗渣进行洗脱再生,再生的吸附剂可反复使用。     

重金属离子在腐植酸上吸附的研究

对4种代表性重金属离子在腐植酸上吸附、pH对竞争吸附的影响及其吸附机理进行了研究。结果表明，Cu2＋、Pb2＋、Zn2＋的吸附等温线为F型，而Cd2＋等温线为L型；2．5＜pH＜3．5时，竞争吸咐次序为Cu2＋＞Pb2＋＞Cd2＋＞Zn2＋；pH＞5．0时，Cd2＋＞Cu2＋＞Zn2＋＞Pb2＋；Cu2＋在腐植酸上的吸附主要是以与腐植酸形成配合物的方式相互结合。     

原位帽封材料对水体中Pb(Ⅱ)与Cd(Ⅱ)静态吸附

用无纺布包裹珊瑚和丙烯酸树脂制成帽封材料,将底泥中重金属离子原位固定的同时吸附水体中的重金属离子pb2和Cd2.通过红外光谱,电镜扫描和火焰原子吸收仪器来分析该帽封材料的吸附性能.通过改变pH值,吸附剂投放量来检测其吸附效果.结果表明,该帽封材料在pH等于5的时候,Cd2最大吸附量达到434.67 mg/g,pb2+最大吸附量达到524.27 mg/g.pH和吸附剂量保持不变,随着底物浓度增加吸附量也增加;电镜扫描图和红外光谱图表明,该材料能很好地吸附重金属离子.     

花生壳、大豆壳和柚子皮对Cr3+、Cu2+和Ni2+的吸附研究

采用农林废弃物花生壳、大豆壳、柚子皮对重金属离子Cr3+、Cu2+和Ni2+进行吸附研究,探讨反应时间、吸附剂用量、pH、重金属离子初始浓度以及温度对吸附的影响.结果表明:柚子皮对Cr3+、Cu2+、Ni2+的吸附效果优于花生壳和大豆壳,其在20℃、pH 5.00、10.0 mg/kg条件下,反应360 min,Cr3+、Cu2+、Ni2+的吸附率分别可达83.20％、84.50％、59.10％;花生壳、大豆壳和柚子皮对Ni2+的吸附率远低于Cr3+和Cu2+;花生壳、大豆壳和柚子皮对Cr3+、Cu2+、Ni2+的吸附动力学可以用准二级动力学方程描述;吸附率随初始重金属离子浓度增加而降低,其吸附等温线可以用Langmuir方程描述;在一定范围内,吸附率随吸附剂用量增加而增加;溶液初始pH在2～5时,吸附率随pH增大而增加;Cu2、Ni2+的吸附量随温度的上升而逐渐减少,但Cr3+的吸附量随着温度的上升而略增加.     

改性甘蔗渣吸附废水中低浓度Cu2+的研究

利用离子液氯化-1-己基-3-甲基咪唑对甘蔗渣进行改性,利用改性甘蔗渣吸附去除模拟废水中低浓度的Cu2+,并对比了较优条件下甘蔗渣改性前后的Cu2+吸附性能.结果表明,溶液pH、改性甘蔗渣投加量、吸附时间对改性甘蔗渣吸附Cu2+均有一定的影响,较佳的溶液pH为5.41、改性甘蔗渣投加量为0.30 g、吸附时间为130 min;吸附温度升高Cu2+吸附率反而降低,因此选择在室温下进行吸附反应为宜;在以上较优条件下,改性甘蔗渣和甘蔗渣的Cu2+吸附率分别为83.20％和53.83％,前者的Cu2+吸附率提高了30.35％.     

Multi-component adsorption of copper,nickel and zinc from aqueous solutions onto activated carbon prepared from date stones

The removal of Cu²⁺, Ni²⁺, and Zn²⁺ ions from their multi-component aqueous mixture by sorption on activated carbon prepared from date stones was investigated. In the batch tests, experimental parameters were studied, including solution pH, contact time, initial metal ions concentration, and temperature. Adsorption efficiency of the heavy metals was pH-dependent and the maximum adsorption was found to occur at around 5.5 for Cu, Zn, and Ni. The maximum sorption capacities calculated by applying the Langmuir isotherm were 18.68 mg/g for Cu, 16.12 mg/g for Ni, and 12.19 mg/g for Zn. The competitive adsorption studies showed that the adsorption affinity order of the three heavy metals was Cu²⁺?>?Ni²⁺?>?Zn²⁺. The test results using real wastewater indicated that the prepared activated carbon could be used as a cheap adsorbent for the removal of heavy metals in aqueous solutions.     

4种脂肪多胺修饰硅胶对铅离子的吸附

为了合成高效铅离子吸附剂,了解其对铅离子的吸附规律。采用(3-氯丙基)三甲氧基硅烷(CPTS)架桥法,以硅胶(SG)为载体,乙二胺(EDA)、二乙烯三胺(DETA)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)为表面修饰剂,合成了4种胺化硅胶,测定了它们的红外光谱、热重等性质以及对Cu2+、Zn2+和Pb2+的吸附能力。结果表明,4种胺化硅胶对Pb2+的吸附量均大于Cu2+和Zn2+的吸附量,其中DETA修饰硅胶对Pb2+的吸附量较高。4种胺化硅胶对Pb2+的吸附过程较好地符合拟二级动力学模型以及Langmuir和Scatchart等温吸附热力学模型,其对Pb2+吸附的速率常数、饱和吸附量以及吸附位点数由大到小的顺序一致,均为SG-DETASG-TEPASG-EDASG-TETA。4种胺化硅胶对Pb2+的吸附速率和吸附量呈现"奇数胺"增强效应,亲和常数则依次减小。阐明了脂肪多胺修饰硅胶对Pb2+的吸附规律,并进一步讨论了Scatchart和Langmuir热力学模型的统一性。     

Effect of Ca2+-ions on the absorption of Pb2+, Cu2+, Cd2+ and Zn2+ by humic substances

Distribution coefficients for the sorption of Pb²⁺, Cu²⁺, Cd²⁺ and Zn²⁺ by peat were determined as a function of the Ca²⁺-content of peat as well as of the Ca²⁺-concentration in the solution. The amount of heavy metal ions taken up was measured for Cu²⁺, Cd²⁺ and Zn²⁺ by atomic absorption spectrometry and for Pb²⁺ by using Pb-212 as a radioactive tracer.The results show that the distribution coefficients of the heavy metal ions increase, if one increases the initial ratio of the $\text{Ca}{}^{\mathrm{2+}}\text{H}{}^{\mathrm{+}}\text{-}\text{ions}$ in the peat phase. The distribution coefficients for the heavy metal ions decrease, however, if - at constant initial Ca²⁺-content of the peat - the Ca²⁺-concentration of the solution is increased.     

Cadmium (Cd2+) removal by nano zerovalent iron: surface analysis, effects of solution chemistry and surface complexation modeling

Nano zerovalent iron (nZVI) is an effective remediant for removing various organic and inorganic pollutants from contaminated water sources. Batch experiments were conducted to characterize the nZVI surface and to investigate the effects of various solution properties such as pH, initial cadmium concentration, sorbent dosage, ionic strength, and competitive ions on cadmium removal by nZVI. Energy-dispersive X-ray and X-ray photoelectron spectroscopy results confirmed removal of Cd²⁺ ions by nZVI through adsorption. Cd²⁺ adsorption decreased in the presence of competitive cations in the order: Zn²⁺?>?Co²⁺?>?Mg²⁺?>?Mn²⁺?=?Cu²⁺?>?Ca²⁺?>?Na²⁺?=?K⁺. Higher concentrations of Cl^? significantly decreased the adsorption. Cadmium removal increased with solution pH and reached a maximum at pH 8.0. The effects of various solution properties indicated Cd²⁺ adsorption on nZVI to be a chemisorption (inner-sphere complexation) process. The three surface complexation models (diffuse layer model, constant capacitance model, and triple layer model) fitted well to the adsorption edge experimental data indicating the formation of nZVI–Cd bidentate inner-sphere surface complexes. Our results suggest that nZVI can be effectively used for the removal of cadmium from contaminated water sources with varying chemical conditions.     

矸石基X型分子筛对水中Co2+、Cu2+、Cd2+和Cr3+的去除

以煤矸石为原料,采用碱熔后水热合成法制备X型分子筛并进行XRD、SEM、BET和Zeta电位分析。研究其对水中Co2+、Cu2+、Cd2+和Cr3+4种离子的吸附性能,包括吸附等温线、吸附动力学以及初始金属离子浓度、pH值对吸附性能的影响。所合成的矸石基X型分子筛的BET比表面积为676.02 m2/g,微孔孔容为0.263 cm3/g。吸附实验表明,矸石基X型分子筛能有效去除上述4种离子,同时实现煤矸石的资源化和金属离子的去除。4种离子的平衡吸附量均随初始浓度的增大而增大,相同条件下平衡吸附量的大小顺序为Cd2+>Cr3+>Cu2+>Co2+。准二级动力学模型能很好地描述4种离子的吸附动力行为。Langmuir模型对Co2+、Cu2+和Cd2+吸附的拟合较Freundlich模型高,说明其主要表现为物理吸附过程。4种离子的吸附速率均由液膜扩散和颗粒内扩散共同控制。     

Simultaneous adsorption and degradation of Zn2+ and Cu2+ from wastewaters using nanoscale zero-valent iron impregnated with clays

Clays such as kaolin, bentonite and zeolite were evaluated as support material for nanoscale zero-valent iron (nZVI) to simultaneously remove Cu²⁺ and Zn²⁺ from aqueous solution. Of the three supported nZVIs, bentonite-supported nZVI (B-nZVI) was most effective in the simultaneous removal of Cu²⁺ and Zn²⁺ from a aqueous solution containing a 100 mg/l of Cu²⁺ and Zn²⁺, where 92.9 % Cu²⁺ and 58.3 % Zn²⁺ were removed. Scanning electronic microscope (SEM) revealed that the aggregation of nZVI decreased as the proportion of bentonite increased due to the good dispersion of nZVI, while energy dispersive spectroscopy (EDS) demonstrated the deposition of copper and zinc on B-nZVI after B-nZVI reacted with Cu²⁺ and Zn²⁺. A kinetics study indicated that removing Cu²⁺ and Zn²⁺ with B-nZVI accorded with the pseudo first-order model. These suggest that simultaneous adsorption of Cu²⁺and Zn²⁺ on bentonite and the degradation of Cu²⁺and Zn²⁺ by nZVI on the bentonite. However, Cu²⁺ removal by B-nZVI was reduced rather than adsorption, while Zn²⁺ removal was main adsorption. Finally, Cu²⁺, Zn²⁺, Ni²⁺, Pb²⁺ and total Cr from various wastewaters were removed by B-nZVI, and reusability of B-nZVI with different treatment was tested, which demonstrates that B-nZVI is a potential material for the removal of heavy metals from wastewaters.     

Adsorptive removal of Pb2+ form aqueous solution by macrocyclic calix[4]naphthalene: kinetic, thermodynamic, and isotherm analysis

Background

The adsorption characteristics of Pb²⁺ ions from aqueous solutions onto calix[4]naphthalene have been investigated.

Method

Calix[4]naphthalene was prepared by the condensation of 1-naphthol and formaldehyde (1:2) in presence of hydrochloric acid at 80°C. The effect of various operation parameters, such as solution pH, initial metal ion concentration, contact time, and temperature, on the adsorption capacity of calix[4]naphthalene for Pb²⁺ have been investigated.

Result

Experimental results showed that the adsorption of Pb²⁺ ions increased with the increase in solution pH and temperature. Langmuir and Freundlich isotherms models were used to describe the adsorption behavior of Pb²⁺ by calix[4]naphthalene. Equilibrium data fitted well with the Langmuir isotherm model and the maximum adsorption capacity of calix[4]naphthalene for Pb²⁺ at 30°C was found to be 29.15 mg g^?1. Kinetic studies indicated that the adsorption followed pseudo-second order model and the thermodynamic studies revealed that the adsorption process was spontaneous and endothermic in nature. The obtained results demonstrated that calix[4]naphthalene can be used as an effective adsorbent for Pb²⁺ ions removal from water.