Nanocomposites based on poly(butylene adipate‐co‐terephthalate) and montmorillonite

Nanocomposites based on biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and layered silicates were prepared by the melt intercalation method. Nonmodified montmorillonite (MMT) and organo‐modified MMTs (DA‐M, ODA‐M, and LEA‐M) by the protonated ammonium cations of dodecylamine, octadecylamine, and N‐lauryldiethanolamine, respectively, were used as the layered silicates. The comparison of interlayer spacing between clay and PBAT composites with inorganic content 3 wt % measured by X‐ray diffraction (XRD) revealed the formation of intercalated nanocomposites in DA‐M and LEA‐M. In case of PBAT/ODA‐M (3 wt %), no clear peak related to interlayer spacing was observed. From morphological studies using transmission electron microscopy, the ODA‐M was found to be finely and homogeneously dispersed in the matrix polymer, indicating the formation of exfoliated nanocomposite. When ODA‐M content was increased, the XRD peak related to intercalated clay increased. Although the exfoliated ODA‐M (3 wt %) nanocomposite showed a lower tensile modulus than the intercalated DA‐M and LEA‐M (3 wt %) composites, the PBAT/ODA‐M composite with inorganic content 5 wt % showed the highest tensile modulus, strength, and elongation at break among the PBAT composites with inorganic content 5 wt %. Their tensile properties are discussed in relation to the degree of crystallinity of the injection molded samples. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 386–392, 2005     

Formulation and characterization of compatibilized poly(lactic acid)‐based blends and their nanocomposites with silver‐loaded kaolinite

Biodegradable polymer nanocomposites have been developed in this study as materials for use in the packaging of moisture‐sensitive products. Poly(lactic acid) (PLA) was the main component of the nanocomposites with poly(butylene adipate‐co‐terephthalate) (PBAT) as flexibility enhancer. Tetrabutyl titanate was also added as a compatibilizer to enhance the interfacial affinity between PLA and PBAT by inducing the formation of some PLA/PBAT via transesterification during the melt blending process, thereby improving the mechanical properties of the blends. Silver‐loaded kaolinite synthesized via chemical reduction was also incorporated into the compatibilized blends for further property improvement. Herein, we report a novel biodegradable quaternary nanocomposite system with intercalated‐exfoliated clay dispersion that was uniquely achieved by increasing the interlamellar space between kaolinite layers through silver nanoparticle insertion. The resultant nanocomposites containing as little as 4 phr modified clay reduced the elongation at break from 213.0 ± 5.85% to 53.8 ± 1.81%, enhanced thermal stability (initial decomposition temperature increased from 378 °C to 399 °C) and exhibited a water vapor permeability reduction of 41.85%. On the basis of these properties, the developed nanocomposites are considered to be promising candidates for use in bio‐packaging applications to replace non‐biodegradable and petro‐based plastics. © 2014 Society of Chemical Industry     

Bio‐based polymer nanocomposites based on layered silicates having a reactive and renewable intercalant

Soybean oil‐based polymer nanocomposites were synthesized from acrylated epoxidized soybean oil (AESO) combined with styrene monomer and montmorillonite (MMT) clay by using in situ free radical polymerization reaction. Special attention was paid to the modification of MMT clay, which was carried out by methacryl‐functionalized and quaternized derivative of methyl oleate intercalant. It was synthesized from olive oil triglyceride, as a renewable intercalant. The resultant nanocomposites were characterized by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The effect of increased nanofiller loading in thermal and mechanical properties of the nanocomposites was investigated by thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). The nanocomposites exhibited improved thermal and dynamic mechanical properties compared with neat acrylated epoxidized soybean oil based polymer matrix. The desired exfoliated nanocomposite structure was achieved when the OrgMMT loading was 1 and 2 wt % whereas partially exfoliated nanocomposite was obtained in 3 wt % loading. It was found that about 400 and 500% increments in storage modulus at glass transition and rubbery regions, respectively were achieved at 2 wt % clay loading compared to neat polymer matrix while the lowest thermal degradation rate was gained by introducing 3 wt % clay loading. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2031–2041, 2013     

Effect of clay exfoliation and organic modification on morphological,dynamic mechanical,and thermal behavior of melt‐compounded polyamide‐6 nanocomposites

Polyamide‐6/clay nanocomposites were prepared employing melt bending or compounding technique followed by injection molding using different organically modified clays. X‐ray diffraction and transmission electron microscopy were used to determine the molecular dispersion of the modified clays within the matrix polymer. Mechanical tests revealed an increase in tensile and flexural properties of the matrix polymer with the increase in clay loading from 0 to 5%. C30B/polyamide‐6 nanocomposites exhibited optimum mechanical performance at 5% clay loading. Storage modulus of polyamide‐6 also increased in the nanocomposites, indicating an increase in the stiffness of the matrix polymer with the addition of nanoclays. Furthermore, water absorption studies confirmed comparatively lesser tendency of water uptake in these nanocomposites. HDT of the virgin matrix increased substantially with the addition of organically modified clays. DSC measurements revealed both γ and α transitions in the matrix polymer as well as in the nanocomposites. The crystallization temperature (T_c) exhibited an increase in case of C30B/polyamide‐6 nanocomposites. Thermal stability of virgin polyamide‐6 and the nanocomposites has been investigated employing thermogravimetric analysis. POLYM. COMPOS., 28:153–162, 2007. © 2007 Society of Plastics Engineers     

Synthesis and characterization of polystyrene/layered double‐hydroxide nanocomposites via in situ emulsion and suspension polymerization

Polystyrene (PS)/ZnAl layered double‐hydroxide (LDH) nanocomposites were synthesized via in situ emulsion and suspension polymerization in the presence of N‐lauroyl‐glutamate surfactant and long‐chain spacer and characterized with elemental analysis, Fourier transform infrared spectrum, X‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetric analysis. The XRD and TEM results demonstrate that the exfoliated ZnAl–LDH layers were well dispersed at molecular level in the PS matrix. The completely exfoliated PS/LDH nanocomposites were obtained even at the 20 and 10 wt % LDH loadings prepared by emulsion polymerization and suspension polymerization, respectively. The PS/LDH nanocomposites with a suitable amount of LDH showed apparently enhanced thermal stability. When the 50% weight loss was selected as a comparison point, the decomposition temperature of the exfoliated PS/LDH sample prepared by emulsion polymerization with a 5 wt % LDH loading was about 28°C higher than that of pure PS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3758–3766, 2006     

Synthesis and characterization of biodegradable aliphatic–aromatic nanocomposites fabricated using maleic acid‐grafted poly[(butylene adipate)‐co‐terephthalate] and organically modified layered zinc phenylphosphonate

A new series of biodegradable aliphatic–aromatic nanocomposites containing maleic acid‐grafted poly[(butylene adipate)‐co‐terephthalate] (g‐PBAT) and organically modified layered zinc phenylphosphonate (m‐PPZn) were successfully synthesized through transesterification and polycondensation processes with covalent linkages between the polymeric and inorganic materials. Fourier transform infrared and ¹³C NMR spectra demonstrate the successful grafting of maleic acid to PBAT. The morphology of g‐PBAT/m‐PPZn nanocomposites was investigated using wide‐angle X‐ray diffraction and transmission electron microscopy. Results showed that the stacking layers of m‐PPZn were distributed and intercalated into the g‐PBAT polymer matrix. The incorporation of m‐PPZn into the g‐PBAT matrix significantly enhanced the storage modulus at ?70 °C as compared to that of neat g‐PBAT. A reduction in thermal stability was observed for all g‐PBAT/m‐PPZn systems, which is probably due to the lower thermal stability of m‐PPZn. The biodegradation of neat g‐PBAT copolymers and g‐PBAT/m‐PPZn nanocomposites was investigated using lipase from Pseudomonas sp. The degradation rates of neat g‐PBAT copolymers decrease in the order g‐PBAT‐80 > g‐PBAT‐50 > g‐PBAT‐20. The faster degradation rate of g‐PBAT‐80 is a result of the higher content of adipate acid units and the chain flexibility of the polymer backbone. Furthermore, the weight loss increases as the loading of m‐PPZn increases, indicating that the presence of m‐PPZn improves the degradation of the g‐PBAT copolymers. This result might be accounted for by the lower degree of crystallinity for g‐PBAT/m‐PPZn nanocomposites. © 2019 Society of Chemical Industry     

The Effect of Clay Loading on the Morphology and Properties of Poly(styrene‐co‐butyl acrylate)/Clay Nanocomposites

This paper investigates the effect of both the clay loading and the monomer feed rate on the morphology and properties of poly(styrene‐co‐butyl acrylate)‐clay nanocomposites prepared in emulsion polymerization. Analysis by X‐ray diffraction (XRD) and transmission electron microscopy (TEM) of the nanocomposites prepared by batch polymerization showed that the polymer clay nanocomposites (PCNs) with 1–3 wt.‐% clay loading resulted in intercalated structures, while exfoliated structures were obtained at 10 wt.‐% clay loading. The polymerization was also carried out with semi‐batch polymerization. The morphology, thermal stability, and mechanical properties of nanocomposites obtained were found to be more strongly dependent on the clay/polymer ratio than the monomer feed rate.

     

Improving heat ageing and thermal properties of silicone rubber using montmorillonite clay

Heat ageing and thermal stability of a silicone rubber (SR) filled with montmorillonite clay (MMT) was investigated. Three types of rubber nanocomposites were prepared with highly exfoliated Cloisite 30B (SR/C30B), intercalated/exfoliated Cloisite Na⁺ (SR/Na⁺MMT), and highly intercalated Cloisite 20A (SR/C20A). This study showed that the SR/C30B nanocomposite exhibited excellent heat resistance in comparison to the other two nanocomposites and neat SR as revealed by higher retention strength. The thermal stability of the rubber in air was strongly dependent on the clay morphology and increased in the following order: highly intercalated/exfoliated SR/Na⁺MMT < highly intercalated SR/C20A < highly exfoliated SR/C30B. The thermogravimetric analyses of the SR/C30B nanocomposite showed a substantial increase in the final residue in comparison with the neat SR. This indicated a major improvement in the thermal stability of the rubber containing the exfoliated clay, which was also supported by the higher activation energy of decomposition measured for the nanocomposite. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41061.     

A new model for estimation of the thermal conductivity of polymer/clay nanocomposites

High density polyethylene– and polypropylene–clay nanocomposites are synthesized by melt blending, in which polyethylene glycol and polypropylene glycol are used as compatibilizers to increase the space of galleries. The morphology properties of nanocomposites are explored by X‐ray diffraction and transition electron microscopy. The thermal conductivity coefficient (K) of nanocomposites is also measured along with the thermal stability. A conventional model based on developed Maxwell‐Garnett formula is also established to predict the thermal conductivity of polymer/clay nanocomposites with clay loading. Morphology results indicate that two intercalated and exfoliated structures are formed. The established model satisfactorily predicts the K values of nanocomposites for low range of clay content. Thermogravimetric analysis shows remarkable thermal stability of nanocomposites with 10 wt % of clay content. The deviation of our model from experimental result for 10 wt % of clay can be attributed to the intercalated structure of layered silicates into the matrices. Although the K values do not considerably increase in 5 wt % with respect to the increase occurs for 10 wt % of clay, but it increases about 28 and 37% at 50°C for high density polyethylene– and polypropylene–clay nanocomposites, respectively. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical,Thermal and Viscoelastic Behavior of Nylon 6/Clay Nanocomposites with Cotreated Montmorillonites

Nylon 6 nanocomposites were prepared using melt intercalation technique. Sodium montmorillonite (Na-MMT) was modified with octadecyl ammonium salt to evaluate the effect of clay modification on the performance of the nanocomposites. A comparative account with the nanocomposites prepared, using commercial clay cloisite 30B has been presented. X-ray diffraction (XRD) studies indicated an increase in the basal spacing of organically modified clays. Further, X-ray diffractograms of the nanocomposites displayed the absence of basal reflections suggesting the formation of an exfoliated structure. Transmission electron microscopy (TEM) investigations also confirmed exfoliation of clay galleries in the nanocomposites. Differential scanning calorimetry (DSC) measurements revealed both γ and α transitions in the matrix polymer as well as the nanocomposites. The crystallization temperature (T_c) exhibited a marginal increase in the C30B/Nylon 6 nanocomposites. Thermal stability of virgin Nylon 6 and the nanocomposites has been investigated using thermogravimetric analysis. Mechanical test revealed an increase in the tensile and flexural properties of Nylon 6 with the incorporation of nanoclays. Storage and loss modulus of virgin matrix increased with the incorporation of nanoclays. C30B/Nylon 6 nanocomposites exhibited optimum performance at 5% clay loading. Further, water absorption studies also confirmed comparatively lesser tendency of water uptake in these nanocomposites.     

Biopolyester‐based nanocomposites: Structural,thermo‐mechanical and biocompatibility characteristics of poly(3‐hydroxybutyrate)/montmorillonite clay nanohybrids

In this work, the structural, thermal, mechanical, and biocompatibility characteristics of biopolyester‐based nanocomposites with phyllosilicate clays, namely those of poly(3‐hydroxybutyrate) (PHB) with octadecylamine‐modified montmorillonite (C₁₈MMT), are reported. PHB/clay nanocomposites with various loadings were prepared by melt mixing. X‐ray diffraction measurements and transmission electron microscopy images revealed the coexistence of intercalated and exfoliated states in the produced nanocomposites. Atomic force microscopy imaging also shed light to the morphological characteristics of the pure PHB and the prepared nanocomposites. The thermal stability of the nanohybrid materials was improved with the 5 wt % loading nanocomposite to show the best improvement. In addition, the nanohybrids have lower melting point compared to pure PHB and enhanced storage modulus (E′). Finally, the biocompatibility of pristine PHB and the 5 wt % nanocomposite was assessed by studying the morphology and proliferation of osteoblast cells attached on their surfaces. The results after 3 and 7 days of cell culturing indicate the incorporation of nanoclays does not change the cell adhesion and spreading as compared to those on pure PHB. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41628.     

Effect of oligomeric‐modified montmorillonite on morphology and properties of polycarbonate/montmorillonite nanocomposites

Low‐molecular‐weight copolymers of styrene and vinylbenzyl ammonium salts (oligomeric surfactant) were used to modify montmorillonite (MMT). The oligomeric‐modified MMT showed good thermal stability, which made it suitable to be used for preparing polycarbonate(PC)/MMT nanocomposites at high temperature. A different series of PC/MMT nanocomposites had been prepared by melt processing using a twin screw extruder. The effect of oligomeric surfactant structure and clay loading on the morphology, mechanical property, thermal stability, and color appearance of the nanocomposites were explored. The results of X‐ray diffraction and transmission electron microscopy analyses indicated that the PC/MMT nanocomposites had partially exfoliated structures. The PC/MMT nanocomposites were found to retain light colored, which was important for optical application. Compared to neat PC, the nanocomposites showed better properties of thermal stability and heat insulation. The mechanical properties of the nanocomposites are significantly enhanced by incorporating clay into the PC matrix. The tensile strength of nanocomposites with 2 wt% clay content was up to 55 MPa, which was much higher than that of the neat PC (37 MPa). The maximum tensile modulus value was 19% higher than that of neat PC. POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Synthesis of bio‐based polymeric nanocomposites from acrylated epoxidized soybean oil and montmorillonite clay in the presence of a bio‐based intercalant

Polymeric nanocomposites were synthesized from functionalized soybean‐oil‐based polymer matrix and montmorillonite (MMT) clay using an in situ free radical polymerization reaction. Acrylated epoxidized soybean oil combined with styrene was used as the monomer. Organophilic MMT (OrgMMT) was obtained using a quaternized derivative of methyl oleate, which was synthesized from olive oil triglyceride, as a renewable intercalant. The resultant nanocomposites were characterized using X‐ray diffraction and atomic force microscopy. The effect of increased nanofiller loading on the thermal and mechanical properties of the nanocomposites was investigated using thermogravimetric analysis and dynamic mechanical analysis. It was found that the desired exfoliated nanocomposite structure was achieved when the OrgMMT loading was 1 and 2 wt%, whereas a partially exfoliated or intercalated nanocomposite was obtained for 3 wt% loading. All the nanocomposites were found to have improved thermal and mechanical properties as compared with virgin acrylated epoxidized soybean‐oil‐based polymer matrix. The nanocomposite containing 2 wt% OrgMMT clay was found to have the highest thermal stability and best dynamic mechanical performance. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of polypropylene/clay nanocomposites

Polypropylene/clay (PP/clay) nanocomposites were synthesized via intercalative polymerization. The nanostructure of the composites was investigated by wide‐angle X‐ray diffractometry (WAXD) and transmission electron microscopy (TEM). The WAXD patterns of the PP/clay nanocomposites indicated that the characteristic diffraction peak of the clay disappeared. The TEM image showed the clay was exfoliated into nanometer size and dispersed uniformly in the PP matrix. The composites exhibited much higher storage modulus compared to that of pure PP. At temperatures higher than T_g, the storage modulus of the PP/clay nanocomposites with 8.1 wt % clay content increased three times that of the pure PP. Additionally, the thermal stability of the nanocomposites significantly increased. The maximum decomposition temperature was increased by 44°C with the introduction of about 10 wt % clay. The heat‐distortion temperatures (HDTs) of the nanocomposites also increased. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3611–3617, 2001     

Morphology,thermal, and mechanical properties of polyamide 66/clay nanocomposites with epoxy‐modified organoclay

A new kind of organophilic clay, cotreated by methyl tallow bis‐2‐hydroxyethyl quaternary ammonium and epoxy resin into sodium montmorillonite (to form a strong interaction with polyamide 66 matrix), was prepared and used in preparing PA66/clay nanocomposites (PA66CN) via melt‐compounding method. Three different types of organic clays, CL30B–E00, CL30B–E12, and CL30B–E23, were used to study the effect of epoxy resin in PA66CN. The morphological, mechanical, and thermal properties have been studied using X‐ray diffraction, transmission electron microscopy (TEM), mechanical, and thermal analysis, respectively. TEM analysis of the nanocomposites shows that most of the silicate layers were exfoliated to individual layers and to some thin stacks containing a few layers. PA66CX–E00 and PA66CX–E12 had nearly exfoliated structures in agreement with the SAXS results, while PA66CX–E23 shows a coexistence of intercalated and exfoliated structures. The storage modulus of PA66 nanocomposites was higher than that of the neat PA66 in the whole range of tested temperature. On the other hand, the magnitude of the loss tangent peak in α‐ or β‐transition region decreased gradually with the increase in the clay loading. Multiple melting behavior in PA66 was also observed. Thermal stability more or less decreased with an increasing inorganic content. Young's modulus and tensile strength were enhanced by introducing organoclay. Among the three types of nanocomposites prepared, PA66CX–E12 showed the highest improvement in properties, while PA66CX–E23 showed properties inferior to that of PA66CX–E00 without epoxy resin. In conclusion, an optimum amount of epoxy resin is required to form the strong interaction with the amide group of PA66. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1711–1722, 2006     

Thermal–oxidative degradation and accelerated aging behavior of polyamide 6/epoxy resin‐modified montmorillonite nanocomposites

Polyamide 6 (PA6) nanocomposites based on epoxy resin‐modified montmorillonite (EP‐MMT) were prepared by melt processing using a typical twin‐screw extruder. X‐ray diffraction combined with transmission electron microscopy was applied to elucidate the structure and morphology of PA6/EP‐MMT nanocomposites, suggesting a nearly exfoliated structure in the nanocomposite with 2 wt % EP‐MMT (PA6/2EP‐MMT) and a partial exfoliated‐partial intercalated structure in PA6/4 wt %EP‐MMT nanocomposite (PA6/4EP‐MMT). The thermogravimetric analysis under air atmosphere was conducted to characterize the thermal–oxidative degradation behavior of the material, and the result indicated that the presence of EP‐MMT could inhibit the thermal‐oxidative degradation of PA6 effectively. Accelerated heat aging in an air circulating oven at 150°C was applied to assess the thermal–oxidative stability of PA6 nanocomposites through investigation of reduced viscosity, tensile properties, and chemical structure at various time intervals. The results indicated that the incorporation of EP‐MMT effectively enhanced the thermal–oxidative stability of PA6, resulting in the high retention of reduced viscosity and tensile strength, and the low ratio of terminal carboxyl group to amino group. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40825.     

Synthesis and characterization of epoxy based nanocomposites

Epoxy‐clay nanocomposites were synthesized to examine the effects of the content and type of different clays on the structure and mechanical properties of the nanocomposites. Diglycidyl ether of bisphenol‐A (epoxy) was reinforced by 0.5–11 wt % natural (Cloisite Na⁺) and organically modified (Cloisite 30B) types of montmorillonite. SEM results showed that as the clay content increased, larger agglomerates of clay were present. Nanocomposites with Cloisite 30B exhibited better dispersion and a lower degree of agglomeration than nanocomposites with Cloisite Na⁺. X‐ray results indicated that in nanocomposites with 3 wt % Cloisite 30B, d‐spacing expanded from 18.4 Å (the initial value of the pure clay) to 38.2 Å. The glass transition temperature increased from 73°C, in the unfilled epoxy resin, to 83.5°C in the nanocomposite with 9 wt % Cloisite 30B. The tensile strength exhibited a maximum at 1 wt % modified clay loading. Addition of 0.5 wt % organically modified clay improved the impact strength of the epoxy resin by 137%; in contrast, addition of 0.5 wt % unmodified clay improved the impact strength by 72%. Tensile modulus increased with increasing clay loading in both types of nanocomposites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1081–1086, 2005     

Effect of clay type and loading on thermal,mechanical properties and biodegradation of poly(lactic acid) nanocomposites

PLA nanocomposites based on two different clays (CLO30B and SOMMEE) at 5 and 10 wt.% clay loading were prepared by melt-blending, obtaining a good level of clay dispersion as well as considerable thermo-mechanical improvements in PLA, according to WAXS, SEM, TEM, DMTA and tensile strength analysis.Addition of clays induced PLA crystallization by nucleation, especially upon addition of SOMMEE, promoting kinetics and extent of crystallization of the polymer, especially at high clay content. Concerning the thermal and mechanical properties, the highest improvements in PLA matrix were obtained upon 10% clay addition, especially SOMMEE, becoming more noticeable with increasing temperature.An effective degradation of PLA and nanocomposites in compost at 40 °C was also achieved. It was found that addition of nanoparticles, especially SOMMEE, accelerated the degradation process of PLA, particularly at higher clay content, probably due to catalysis by the hydroxyl groups belonging to the silicate layers surface and/or to their organic modifier.     

Crystallization behavior of poly(p‐dioxanone)‐PU/montmorillonite nanocomposites prepared by chain‐extending reaction

Organo‐modified montmorillonites and poly(p‐dioxanone) (PPDO) diol prepolymers were used to prepare Poly(p‐dioxanone)‐PU/organic montmorillonite (PPDO‐PU/OMMT) nanocomposites by chain‐extending reaction. The crystallization behavior and spherulitic morphology of PPDO‐PU/OMMT nanocomposites were investigated by WXRD, differential scanning calorimetry, and polarized optical microscopy. The results show that the regularity of the chain structure plays a dominant role during the crystallization process rather than that of OMMT content and its dispersion status in PPDO matrix. With similar molecular weight and same OMMT content, PPDO‐PU/OMMT nanocomposite, which derived from lower molecular weight PPDO prepolymer, exhibits lower crystallization rate, melting point, and crystallinity. The influence of the clay content on the crystallization behavior highly depends on its dispersing state. The nucleating effect of OMMT can be only observed at high loading percentage. For the nanocomposites with low clay loading percentage, the retarding effect of exfoliated platelets on the chain‐ordering into crystal lamellae became the key factor. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Supercritical carbon dioxide (scCO2) dispersion of poly(ethylene terephthalate)/clay nanocomposites: Structural,mechanical, thermal,and barrier properties

Dispersed poly(ethylene terephthalate) (PET)/clay nanocomposites can lead to materials with superior barrier and mechanical properties. PET/clay nanocomposites were prepared by melting extrusion of PET with as‐received or supercritical carbon dioxide (scCO₂) predispersed Cloisite^® 30B (30B). The predispersion of 30B was assessed by WAXD, SEM, and TGA, and results indicated that scCO₂ processing could predisperse 30B and the surface modification of the clay was preserved after processing. The structure of PET/30B nanocomposites was investigated by WAXD and TEM confirming that PET has penetrated into the clays inter‐galleries and the predispersed clays lead to improved interfacial interaction and homogenous clay dispersion. Both tensile strength and Young's modulus were improved by 12.1% and 24.9% respectively, as incorporating of 3 wt % of scCO₂ processed clay. Differential scanning calorimetry (DSC) results indicated that clay particles served as nucleation agent could increase the crystallinity whereas had no impact on melting process. In addition, with the addition of 1 wt % of predispersed clay, a significant reduction of oxygen permeation (～33%) was achieved at 23 °C and the maximum reduction (44%) was achieved by adding 3 wt % processed clay. Moreover, we confirmed the effect of temperature on the permeation of PET/30B nanocomposites depended both on the Arrhenius behavior of the organic phases and tortuous path effects, where improved clay dispersion resulted in a higher effective activation energy. Moreover, the transparency of PET matrix was preserved for all nanocomposites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44779.