PET/PTT共混聚酯的等温结晶行为

使用差示扫描量热仪(DSC)研究不同比例的PET/P1T共混聚酯在205℃的等温结晶行为,并使用Avrami方程对其等温结晶过程进行研究.结晶半周期t1/2,总结晶速率常数k和Avrami指数n的变化表明:在共混体系中,对于PET和PTT而言,另一组分的加入都会对结晶产生阻碍作用,PET与P1T相互影响成核与晶体生长机理.     

纳米SiO2粒子对PET结晶过程的影响

研究了纳米SiO2粒子对PET结晶过程的影响。通过差热分析(DSC),分别研究了改性纳米SiO2对PET的等温结晶和非等温结晶的影响。计算了在不同温度下,不同改性纳米SiO2含量PET的等温结晶动力学方程。结果表明:随着纳米SiO2的加入,可以显著提高PET的结晶性能,Avrami指数n变小,体系发生异相成核。当纳米SiO2的添加量在2％时,体系的结晶能力最好,在所测的5个等温结晶温度中,所有样品在170℃附近的结晶速度最快。     

成核剂在PET结晶中的应用

介绍了聚合物的结晶理论,在PET中加入成核剂进行共混,可以提高PET的结晶速度。阐述了国内外采用成核剂提高PET结晶速度的研究情况,并指出了适用于PET热熔胶的成核剂种类。     

PTT／PET共混体系结晶行为和形态研究

利用差示扫描量热仪、正交偏光显微镜研究了聚对苯二甲酸丙二醇酯(PTT)、聚对苯二甲酸乙二醇酯(PET)及PTT/PET共混体系(质量比为25∶75)的结晶行为、形态和等温结晶动力学。结果表明,PTT/PET共混物中,少量的PTT部分地起到了成核作用,但在一定程度上阻碍了PET链段规则地进入晶格,影响了结晶速率。偏光显微镜观察到PET、PTT和PTT/PET共混物在120℃下1、20min的溶液滴膜有较清晰的球晶。     

成核剂对PET/PEN共混体系非等温结晶的影响

采用差示扫描量热法(DSC)研究了三种成核剂苯甲酸钠(SB)、1,3∶2,4-二亚苄基-D-山梨醇(DBS)、碳酸钙(CaCO3)对聚对苯二甲酸乙二醇酯(PET)/聚2,6-萘二甲酸乙二醇酯(PEN)共混体系的非等温结晶动力学的影响。结果表明,在PET/PEN/成核剂共混体系的非等温熔融结晶过程中,随着冷却速率的升高,结晶起始温度、终止温度、结晶峰温度都向低温方向移动,成核剂的加入使得不同速率下PET/PEN的结晶温度明显提高,结晶更为容易,SB、CaCO3、DBS均起到了较好的成核作用。由于次级结晶的存在,采用Ozawa法不能很好地描述PET/PEN/成核剂共混体系的非等温熔融结晶过程;莫志深法能较好地描述体系的非等温熔融结晶过程。     

回收PET玻纤复合材料的结晶性能研究

制备了成核回收PET及其玻璃纤维复合材料，研究了成核回收PET及其玻璃纤维复合材料的结晶与熔融行为、力学性能和加工性能。结果表明，无论是有机羧酸盐成核剂还是无机成核剂都使回收PET的冷结晶温度逐渐降低，热结晶温度逐渐提高。PBT作为PET结晶促进剂，降低回收PET的冷结晶温度，提高热结晶温度。成核回收PET复合材料的力学性能提高，加工性能改善，成型周期缩短。     

纳米氧化物作为成核剂对PET结晶速率的影响

研究了成核剂纳米氧化镁和纳米氧化硅对聚对苯二甲酸乙二醇酯(PET)结晶速率的影响。通过等温结晶差热分析(DSC)研究了纳米氧化镁在不同含量、不同温度下对PET等温结晶行为的影响。用纳米氧化镁和纳米氧化硅填充PET体系的非等温结晶DSC,由所得冷结晶峰温度值和热结晶峰温度值的对比,探索纳米成核剂对PET结晶速率的影响及其规律。研究结果表明:纳米成核剂均能明显提高PET的结晶速率,而纳米氧化镁比纳米氧化硅对促进PET的结晶效果更好;添加不同含量的纳米氧化镁对PET在不同温度下的等温结晶影响不同,在所研究的范围内,1.0%的添加量较有利于PET的结晶。     

PP/纳米SiO2复合材料的非等温结晶动力学

采用差示扫描量热法研究了聚丙烯（PP）/纳米SiO2复合材料的非等温结晶动力学,研究了纳米粒子的成核活性及复合材料的结晶有效能垒。研究结果表明,纳米SiO2起到异相成核的作用,使PP的结晶峰温升高,结晶总速率增大;增容剂马来酸酐接枝聚丙烯(PP-g-MAH)提高了纳米SiO2的成核活性;添加纳米SiO2使复合材料的结晶有效能垒降低,PP-g-MAH使复合材料的结晶有效能垒增大,但低于纯PP的结晶有效能垒。     

PBT/PET共混切片结晶性质的研究

本研究采用JJY-Ⅰ型光学检偏振仪测试不同配比PBT/PET共混切片的等温结晶性质,用电子计算机处理数据,获得了PBT/PET共混切片的等温结晶动力学参数。并采用准等温处理方法,将等温结晶动力学参数用于非等温过程中,得到不同配比PBT/PET共混切片一系列结晶动力学特性参数。从其中的动力学结晶能力G,可判断在同一稳态纺丝条件下,不同配比PBT/PET卷绕丝的相对结晶度大小;采用PEDSC-Ⅱ型测试了不同共混配比的PBT/PET切片的非等温结晶性质,其结果和用JJY-Ⅰ型测试结果一致;本研究还探讨了添加剂(成核剂)对PBT/PET共混切片结晶性质的影响。     

PP/PET/POE-g-MAH共混合金的等温结晶动力学特性

应用差示扫描量热法(DSC),研究了加入不同份数增容剂POE-g-MAH的PP/PET共混合金及纯PP的等温结晶行为,采用Avrami方程处理等温结晶过程,计算结晶动力学参数。结果表明,随着结晶温度的升高各体系的结晶速率下降,结晶速率常数K、n降低,半结晶时间t1/2延长。同一温度下PET有明显的异相成核作用,提高了基体的结晶速率;POE-g-MAH的加入降低了基体的结晶速率,并且随着增容剂含量的增加,基体的结晶速率逐渐下降。纯PP的等温结晶过程具有异相成核与均相成核的机理,共混合金的等温结晶过程属于异相成核机理。     

PET/PTT共混体系的相容特性及力学性能研究

通过熔融共混法制备了聚对苯二甲酸乙二醇酯(PET)与聚对苯二甲酸醇酯(PTT)的共混物,采用差示扫描量热仪、动态热机械分析仪、万能电子试验机等对共混体系的热性能、动态力学性能及拉伸性能进行了测试。测得PET/PTT共混体系只有1个玻璃化转变温度(Tg)和损耗峰,表明在非晶区完全相容,其中纯PET的Tg为84℃,纯PTT的Tg低于50℃; 而双重熔融峰及热结晶峰宽化现象的出现表明,共混体系在晶区是部分相容,各组分倾向于分别进行有序化排列、单独结晶,其中纯PET的熔点为256℃,纯PTT的熔点为229 ℃;共混体系的拉伸模量和拉伸强度随PTT含量的增加呈上升趋势;但当共混比例接近时体系的拉伸模量和拉伸强度有所下降,共混比为5/5时的拉伸模量和拉伸强度分别低达1098MPa和51MPa。     

Non-isothermal Crystallization Behavior of Poly(ethylene terephthalate)/Poly(trimethylene terephthalate) Blends

Summary Non-isothermal crystallization behavior of Poly(ethylene terephthalate)/Poly(trimethylene terephthalate) blends was investigated by XRD and DSC. By XRD spectra analysis, it could be concluded that PET and PTT crystals coexisted. They did not form the cocrystals due to different chemical structures. The Avrami equations modified by Jeziorny and Ziabicki’s kinetic crystallizability analysis were employed to describe the non-isothermal crystallization process of PET/PTT blends. The results suggested that the entanglement of the two polymer chains decrease the crystallizability of PET and PTT in blend. The crystallization activation energies of the blend evaluated by the Friedman method also indicated that the presence of two components in the blends hinders the crystallization process of both components.     

PET/PTT共混纤维的制备及结构性能研究

将聚对苯二甲酸乙二酯(PET)与聚对苯二甲酸丙二醇酯(PTT)共混纺丝制备PET/PTT共混纤维,研究了共混纤维的结构与性能。结果表明,随着PTT含量的增加,PET/PTT共混纤维的晶粒尺寸逐渐增大;PET/PTT共混纤维的断裂强度较PTT纤维大,回弹性较PET纤维好,沸水收缩率较PET纤维大;当PTT质量分数为50%时,共混纤维的结晶度出现最小值,沸水收缩率出现最大值。     

CDPTT/PTT共混体系的结构和性能研究

将含有间苯二甲酸丙二醇酯-5-磺酸钠(SIPT)阳离子可染聚对苯二甲酸丙二醇酯(CDPTT)与聚对苯二甲酸丙二醇酯(PTT)进行共混制备CDPTT/PTT共混聚酯,讨论了共混比例、共混时间和共混温度对CDPTT/PTT共混聚酯的序列结构、热稳定性、结晶性能的影响。结果表明:CDPTT/PTT的特性粘数([η])随共混温度和共混时间的增加而降低,共混温度对[η]的影响更大;CDPTT/PTT质量比为20/80时,[η]出现最小值。随着CDPTT/PTT共混比的增加,结晶度、熔点、热结晶温度逐渐减小。当CDPTT/PTT中SIPT摩尔分数小于2%时,晶粒尺寸随SIPT含量的增加而增加。     

PET/PTT共混体系相容性的研究

根据B.Schneier公式计算了PET/PTT共混体系△H_m值,通过差示扫描量热法(DSC)、X射线衍射法等手段,对PET/PTT熔融共混体系进行相容性的研究。研究发现:PET/PTT共混体系为热力学相容体系;在无定形区是相容的,在晶区是部分相容的,PTT的加入对PET的结晶有促进作用。     

Miscibility and thermal and mechanical properties of melt‐mixed poly(lactic acid)/poly(trimethylene terephthalate)/(methyl methacrylate)‐butadiene‐styrene copolymer blends

This study examined the miscibility and mechanical properties of melt‐mixed poly(lactic acid) (PLA), poly (trimethylene terephthalate) (PTT), and PLA/PTT blend with 5–10 phr of methyl methacrylate‐butadiene‐styrene copolymer (MBS). The isothermal crystallization kinetics of the PTT blends were analyzed by using the Avrami equation. The Differential Scanning Calorimetry (DSC) and scanning electron microscope results indicated that the miscibility of the PLA/PTT blends was improved by adding 5–10 phr of MBS. Although PLA, with the addition of 10 phr of MBS, had lower tensile strength at yield and higher breaking elongation and impact strength than pure PLA, no improvement in these mechanical properties could be observed in PLA/PTT blends. This result is explained by assuming that the crystallization of PTT at the interface favors the disentanglement of MBS from the PTT domain. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Rheological behavior comparison between PET/HDPE and PC/HDPE microfibrillar blends

The rheological behaviors of in situ microfibrillar blends, including a typical semicrystalline/semicrystalline (polyethylene terephthalate (PET)/high‐density polyethylene (HDPE)) and a typical amorphous/semicrystalline (polycarbonate (PC)/HDPE) polymer blend were investigated in this study. PET and PC microfibrils exhibit different influences on the rheological behaviors of microfibrillar blends. The viscosity of the microfibrillar blends increases with increased PET and PC concentrations. Surprisingly, the length/diameter ratio of the microfibrils as a result of the hot stretch ratio (HSR) has an opposite influence on the rheological behavior of the two microfibrillar blends. The stretched PET/HDPE blend exhibits higher viscosity than the unstretched counterpart, while the stretched PC/HDPE blend exhibits lower viscosity than the unstretched blend. The data obtained in this study will be helpful for constructing a technical foundation for the recycling and utilization of PET, PC, and HDPE waste mixtures by manufacturing microfibrillar blends in the future. POLYM. ENG. SCI., 45:1231–1238, 2005. © 2005 Society of Plastics Engineers     

Miscibility and melting behavior of poly(ethylene terephthalate)/poly(trimethylene terephthalate) blends

The miscibility and melting behavior of binary crystalline blends of poly(ethylene terephthalate) (PET)/poly(trimethylene terephthalate) (PTT) have been investigated with differential scanning calorimetry and scanning electron microscope. The blends exhibit a single composition‐dependent glass transition temperature (T_g) and the measured T_g fit well with the predicted T_g value by the Fox equation and Gordon‐Taylor equation. In addition to that, a single composition‐dependent cold crystallization temperature (T_cc) value can be observed and it decreases nearly linearly with the low T_g component, PTT, which can also be taken as a valid supportive evidence for miscibility. The SEM graphs showed complete homogeneity in the fractured surfaces of the quenched PET/PTT blends, which provided morphology evidence of a total miscibility of PET/PTT blend in amorphous state at all compositions. The polymer–polymer interaction parameter, χ₁₂, calculated from equilibrium melting temperature depression of the PET component was ?0.1634, revealing miscibility of PET/PTT blends in the melting state. The melting crystallization temperature (T_mc) of the blends decreased with an increase of the minor component and the 50/50 sample showed the lowest T_mc value, which is also related to its miscible nature in the melting state. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

PC／PET／催化剂（或抑制剂）共混体系的结晶性及相形态的研究

本文采用ＤＳＣ、ＰＬＭ和ＳＥＭ研究了共混比、共混时间及酯交换反应的催化剂、抑制剂对ＰＣ／ＰＥＴ共混体系的结构、形态的影响。结果表明：ＰＣ／ＰＥＴ是一个部分相容体系；在同等条件下，适当延长共混时间，可使ＰＣ、ＰＥＴ间的相容性变好，但同时严重阻碍ＰＥＴ的结晶；催化剂和抑制剂的加入可以改善ＰＥＴ的结晶性能，提高ＰＥＴ的结晶速率，并且改变体系的相形态，形成结构、性能相异的共混物。这些影响有些是由于它们对酯交换反应的影响而造成，有些则与它们本身的性质有关。