印制电路板铜面保护层对无铅焊点结构影响

采用扫描电镜与能谱测试,研究了两种不同印刷电路板铜面保护层,即有机保护层(Organic Solderability Preservatives,OSP)与浸银层(Immersion Ag,I—Ag),对无铅焊点结构的影响。结果显示,采用有机保护层的焊接界面金属间化合物层厚度明显超过了浸银层;在两种不同保护层中的焊点中,均出现薄片状或树枝状Ag3Sn金属间化合物,但在浸银层焊点中,薄片状Ag3sn主要在焊接界面层处非均匀形核长大,而有机保护层焊点中,薄片状Ag3Sn较少出现,代之以树枝状Ag3Sn近似均匀地分布在焊点中。断口分析显示,采用有机保护层的焊点中出现了较多的气孔,而且气孔主要出现在靠近铜面焊点中,这明显降低了焊点的强度。     

Additive Effect of Kirkendall Void Formation in Sn-3.5Ag Solder Joints on Common Substrates

The Sn-3.5Ag and Sn-3.5Ag-0.2Co-0.1Ni lead-free solders were investigated on common electronics substrates, namely, organic solderability preservative (OSP) and electroless Ni/immersion Au (ENIG) surface finishes. The formation of Kirkendall voids at the interfacial region during isothermal solid aging was explored. For the Sn-3.5Ag-0.2Co-0.1Ni/OSP solder joint, the Kirkendall voids were present after isothermal solid-state aging at higher temperature (e.g., 150°C); however, the size of voids did not change remarkably with prolonged aging time due to the depressed Cu₃Sn layer growth. For ENIG surface finishes, the 0.2Co-0.1Ni additions seemed to enhance the longitudinal groove-shaped voids at the Ni₃P layer; however, void formation at the solder/Ni₃Sn₄ interface was effectively reduced. This might be attributed to the reduced Sn activity in the solder matrix and the suppressed Ni-P-Sn layer formation.     

Effect of Interfacial Reactions on the Reliability of Lead-Free Assemblies after Board Level Drop Tests

The reliability of lead-free electronic assemblies after board level drop tests was investigated. Thin small outline package (TSOP) components with 42 FeNi alloy leads were reflow soldered on FR4 printed circuit boards (PCBs) with Sn3.0Ag0.5Cu (wt%) solder. The effects of different PCB finishes [organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG)], multiple reflow (once and three times), and isothermal aging (500 h at 125°C after one time reflow) were studied. The ENIG finish showed better performance than its OSP counterparts. With the OSP finish, solder joints reflowed three times showed obvious improvement compared to those of the sample reflowed once, while aging led to apparent degradation. The results showed that intermetallic compound (IMC) types, IMC microstructure and solder microstructure compete with each other, all playing very important roles in the solder joint lifetime. The results also showed that it is important to specify adequate conditions for a given reliability assessment program, to allow meaningful comparison between results of different investigators.     

Wetting characteristics of Pb-free solder alloys and PWB finishes

For a successful transition to Pb-free manufacturing in electronics assembly, it is critical to understand the behavior of Pb-free solders (in bulk and paste form) and their interaction with the Pb-free printed wiring board (PWB) finishes. This paper presents the results obtained from solder paste spread tests and wetting balance experiments with several Pb-free solder alloys and Pb-free PWB finishes. The solder alloys studied were Sn3.4Ag4.8Bi, Sn4.0Ag0.5Cu, Sn3.5Ag and Sn0.7Cu. Eutectic Sn37Pb was used as a reference. The PWB surface finishes were Sn, NiAu, Ag and OSP. Wetting balance experiments were conducted in air while the spread tests were performed in air and nitrogen to understand the effect of reflow atmosphere on the spreading. Surface analysis techniques such as Nomarski phase contrast microscopy, Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) were used to characterize the as-received PWB finishes. Sequential electrochemical reduction analysis (SERA) was also performed on the as-received PWB test coupons and on the Sn test coupons after multiple reflow cycles. The effect of multiple reflow cycles on the wetting performance, spreading and the surface composition of the PWB finishes was studied.     

微量Ni对Sn-3.0Ag-0.5Cu钎料及焊点界面的影响

研究了Ni的含量对无铅钎料Sn-3.0Ag-0.5Cu润湿性、熔点、重熔及老化条件下界面化合物(IMC)的影响。结果表明:微量Ni的加入使SnAgCu润湿力增加6%;使合金熔点略升高约3℃;重熔时在界面形成了(Cu,Ni)6Sn5IMC层,且IMC厚度远高于SnAgCu/Cu的Cu6Sn5IMC厚度。在150℃老化过程中,SnAgCuNi/Cu重熔焊点IMC随着时间的增加,其增幅小于SnAgCu/Cu的增幅,此时Ni对IMC的增长有一定抑制作用。     

Effects of Surface Finishes and Current Stressing on Interfacial Reaction Characteristics of Sn-3.0Ag-0.5Cu Solder Bumps

The effects of surface finishes on the in situ interfacial reaction characteristics of ball grid array (BGA) Sn-3.0Ag-0.5Cu lead-free solder bumps were investigated under annealing and electromigration (EM) test conditions of 130°C to 175°C with 5.0 × 10³ A/cm². During reflow and annealing, (Cu,Ni)₆Sn₅ intermetallic compound (IMC) formed at the interface of electroless nickel immersion gold (ENIG) finish. In the case of both immersion Sn and organic solderability preservative (OSP) finishes, Cu₆Sn₅ and Cu₃Sn IMCs formed. Overall, the IMC growth velocity of ENIG was much lower than that of the other finishes. The activation energies of total IMCs were found to be 0.52 eV for ENIG, 0.78 eV for immersion Sn, and 0.72 eV for OSP. The ENIG finish appeared to present an effective diffusion barrier between the Cu substrate and the solder, which leads to better EM reliability in comparison with Cu-based pad systems. The failure mechanisms were explored in detail via in situ EM tests.     

Investigation of the Role of Void Formation at the Cu-to-Intermetallic Interface on Aged Drop Test Performance

Chip-scale packages (CSPs) are widely used in portable electronic products. Mechanical drop testing is a critical reliability requirement for these products. With the switch to lead-free solder, new reliability data must be generated. Most drop test reliability data reported for CSPs are for the as-built condition. However, the mechanical shock reliability over the life of the product is equally important. This paper provides a systematic study of surface finish (immersion Sn and immersion Ag) and reflow profile (cool down rate) on the drop test reliability of CSP assemblies. A limited experiment was also performed with organic solderability preservative (OSP)-coated boards. The Sn finish provides an initial Cu-Sn intermetallic layer, while the Ag finish and OSP coating allows the formation of the initial Cu-Sn intermetallic during the reflow cycle. Drop test results for assemblies as-built and as a function of aging at 125 degC are correlated with cross-sectional analysis of the solder joints. The mean number of drops to failure decreases by approximately 80% with aging at 125 degC through 480 h. Voids develop at the Cu-Sn intermetallic-to-Cu interface during high-temperature aging, but the crack path is through the intermetallic layer and does not propagate from void-to-void. Thus, it can be concluded that the voids do not contribute to the decrease in drop test survivability observed in this study     

无铅化PCB表面材料及工艺特点

无铅化电子组装中PCB表面镀层技术主要有无铅钎料热风整平、浸锡、浸银、化学镀镍/浸金和有机可焊保护层五种。每种工艺技术具有各自的优缺点,每种工艺材料与不同无铅钎料具有不同的兼容性。从可制造性、可生产性以及与无铅钎料的匹配性等方面对五种PCB表面镀层技术做了较为全面的阐述,并通过对润湿性和可靠性评估得到一定的最佳配比,为...     

Ethylene glycol ether free solder paste development

There are growing concerns in the electronics industry for not only finding alternatives to lead but also other potentially hazardous materials as well. This paper summarizes the development of ethylene glycol ether (EGE)-free solder flux for the formulation of lead-free solder pastes. Replacing the toxic components in the flux was only the first challenge, the criteria of commercially proven pastes also had to be met. Both commercial and in-house solder paste formulations were evaluated for printability, reflow, wetting, flux residue removal, and solder void characteristics. Two critical issues, solder bump boids and flux residue removal, were identified and associated with the high temperature reflow of Pb-free pastes. These issues were not effectively improved by the existing commercial EGE-free solder pastes. New solder paste formulations were developed utilizing alternative chemistry than those found in traditional solder paste fluxes. These pastes, some, of which are also water soluble, reduced void frequency and size by more than 4x as compared to vendors' pastes. Solder bump height uniformity of 135 4 m within each die was consistently achieved. Thermal-mechanical reliability tests were performed on various lead-free solder alloys using the new flux formulations. The reliability of flip chip assembled DCA on organic boards with both OSP/Cu and Cu/Ni/au pad metallizations were comparable to eutectic Sn63Pb37 bumped assemblies using commerical pastes.     

Intermetallic reactions in Sn3Ag0.5Cu and Sn3Ag0.5Cu0.06Ni0.01Ge solder BGA packages with Au/Ni surface finishes

The intermetallic compounds (IMCs) formed during the reflow and aging of Sn3Ag0.5Cu and Sn3Ag0.5Cu0.06Ni0.01Ge solder BGA packages with Au/Ni surface finishes were investigated. After reflow, the thickness of (Cu, Ni, Au)₆Sn₅ interfacial IMCs in Sn3Ag0.5Cu0.06Ni0.01Ge was similar to that in the Sn3Ag0.5Cu specimen. The interiors of the solder balls in both packages contained Ag₃Sn precipitates and brick-shaped AuSn₄ IMCs. After aging at 150°C, the growth thickness of the interfacial (Ni, Cu, Au)₃Sn₄ intermetallic layers and the consumption of the Ni surface-finished layer on Cu the pads in Sn3Ag0.5Cu0.06Ni0.01Ge solder joints were both slightly less than those in Sn3Ag0.5Cu. In addition, a coarsening phenomenon for AuSn₄ IMCs could be observed in the solder matrix of Sn3Ag0.5Cu, yet this phenomenon did not occur in the case of Sn3Ag0.5Cu0.06Ni0.01Ge. Ball shear tests revealed that the reflowed Sn3Ag0.5Cu0.06Ni0.01Ge packages possessed bonding strengths similar to those of the Sn3Ag0.5Cu. However, aging treatment caused the ball shear strength in the Sn3Ag0.5Cu packages to degrade more than that in the Sn3Ag0.5Cu0.06Ni0.01Ge packages.     

Morphology and Growth of Intermetallics at the Interface of Sn-based Solders and Cu with Different Surface Finishes

Several types of surface finishes have been applied on Cu substrates in an effort to facilitate bonding and improve the reliability of lead-free solder joints. In the current research, the effects of printed circuit board surface finishes on the reliability of the solder joints were investigated by examining the morphology and growth behavior of the intermetallic compounds (IMCs) between Sn-based solders and different surface finishes on Cu. Three types of Cu substrates with different surface finishes were fabricated in this study: organic solderability preservative (OSP)/Cu, Ni/Cu, and electroless nickel immersion gold (ENIG)/Cu. Sn-3.5Ag and Sn-3.0Ag-0.5Cu were used as the solders. In the experiment, the solder joint specimens were aged isothermally at 150°C for up to 1000 h. Experimental results revealed that the OSP surface finish promoted the interdiffusion between Cu and Sn during soldering. The composition and morphology of the IMC layer at the solder/Ni/Cu interface were sensitive to the Cu concentration in the solder. Meanwhile, the solder joints with different morphological features of the IMCs exhibited significant differences in shear strengths. The Au-containing ENIG surface finish affected the shear strength of the solder joint significantly at the initial stage of isothermal aging.     

Reaction of solder with Ni/Au metallization for electronic packagesduring reflow soldering

Gold over Ni is one of the most common surface finishes for Cu soldering pads in ball-grid-array (BGA) and other electronic packages. The Au layer is for oxidation protection, and the Ni layer serves as a solderable diffusion barrier. In this study, eutectic Pb-Sn solder-balls were reflowed on the Au/Ni/Cu pads, and the chemical interactions between the solder and the surface finish were studied. Quenched-in microstructures at different stages of the reflow were carefully examined using the scanning electron microscopy. It was found that the solder melted locally along the solder/pad interface at the very early stages of the reflow before the whole solder ball had reached the Pb-Sn eutectic temperature. This was because a ternary eutectic reaction L=(Pb)+(Sn)+AuSn₄ occurred at 177°C, six degrees below the Pb-Sn eutectic temperature. Four distinct stages were identified for the reflow process. The four stages are: (1) partial melting of solder balls and the initial reaction of Au with Sn; (2) complete reaction of An with Sn; (3) separation of (Au_xNi_1-x)Sn₄ from the pad; (4) complete melting of solder balls and the reaction of Ni with Sn. After a typical reflow, with a 225°C peak reflow temperature and 115 s reflow time, all the An and Au-bearing intermetallic compounds left the interface and the only intermetallic compound at the interface was Ni₃Sn₄ with a thickness of about 2 μm     

Development of lead-free wave soldering process

Lead-free wave soldering was studied in this work using a 95.5Sn/3.8Ag/0.7Cu alloy. A process DOE was developed, with three variables (solder bath temperature, conveyor speed, and soldering atmosphere), using a dual wave system. Four no-clean flux systems, including alcohol- and water-based types, were included in the evaluation. A specially designed "Lead-Free Solder Test Vehicle", which has various types of components, was used in the experiments. Both organic solderability preservative (OSP) and electroless nickel/immersion gold (Ni/Au, or ENIG) surface finishes were studied. Soldering performance (bridging, wetting and hole filling) was used as the responses for the DOE. In addition, dross formation was measured at different solder bath temperatures and atmospheres. Dross formation with Sn/Ag/Cu bath was compared to that with eutectic Sn/Pb bath. Regarding the connector-type component, a pad design giving the best soldering performance was evaluated based on the DOE results. Finally, a confirmation run with the optimum flux and process parameters was carried out using the Sn/Ag/Cu solder, and a comparative run was made with the Sn/Pb solder alloy and a no-clean flux used in production. The soldering results between the two runs indicate that with optimum flux and process parameters, it is possible to achieve acceptable process performance with the Sn/Ag/Cu alloy.     

Interconnecting to aluminum- and copper-based semiconductors (electroless-nickel/gold for solder bumping and wire bonding)

Electroless nickel and immersion gold plating technologies (e-Ni/Au) have traditionally been used almost exclusively within the electronics industry to create a solderable surface on substrate materials, e.g. laminate boards. Recent advances in these plating technologies, along with the inherent low costs associated with electroless plating processes, have enabled the extension of their utilization into a variety of semiconductor applications, e.g. wafer level pad metallization. This paper describes the electroless nickel and immersion gold processes for both aluminum- and copper-based semiconductors. The nickel plating bath is a hypophosphite-based solution and the gold bath is a cyanide-free sulfate-based solution. For aluminum-based integrated circuits a zincation process is used to initiate nickel growth, and for copper, palladium is used to catalyze the surface. Tight control of the chemistries, equipment, and run-time process variables are required to ensure repeatability. Thin film Auger analysis of the as-plated films shows well-defined layers of high purity gold and nickel/phosphorous. Adhesion of the e-Ni/Au layers was evaluated by measuring the load required to shear I/O pads plated with tall nickel bumps. Integrity of the nickel was further evaluated by subjecting the structures to multiple temperature cycles and test for pad shear strength. Results show no degradation in shear load or failure mode.The deposition of nickel and gold onto the I/O pad surfaces enables the subsequent use of both wire bond and flip chip (lead-based and lead-free alloys) interconnect methods. The integrity of gold wire bonds to the e-Ni/Au plated I/O pad was evaluated using ball shear, wire pull, and the corresponding failure analysis of each. Results show values well above product specifications, with wire pull failure modes in the wire and intermetallic failure in the ball shear studies. For flip chip applications, the e-Ni/Au layer was evaluated using stencil-printing technology to deposit several different solder alloys. In the current investigation, two test vehicles were successfully bumped with both 63Sn/37Pb and 90Pb/10Sn lead-based solder alloys, as well as the 95.5Sn/3.8Ag/0.7Cu lead-free alloy. In order to evaluate the compatibility of these alloys with the electroless nickel layer, solder bump shear tests were performed as a function of number of reflow cycles. Results show no degradation in shear load or failure mode among all three of the alloys tested, indicating no critical nickel consumption (i.e., excessive intermetallic growth) during reflow. Additional tests were performed comparing nickel under-bump-metallurgy (UBM) thicknesses of 1, 2 and 5 μm. Again, no critical nickel consumption was detected.     

Comparison of electroplated eutectic Bi/Sn and Pb/Sn solder bumpson various UBM systems

The effect of a reflow process and under bump metallurgy (UBM) systems on the growth of intermetallic compounds (IMC) of the 57Bi/43Sn and 37Pb/63Sn solder bump/UBM interfaces was investigated. The selected UBM systems were sputtered Al/Ti/Cu, sputtered Al/NiV/Cu, Al/electroless Ni/immersion Au, and Al/Ti/electroless Cu. An alloy electroplating method was used for the solder bumping process. The microstructure and composition of intermetallic compound (IMC) phases and their morphologies were examined using scanning electron microscopy and X-ray diffraction. The Cu₆Sn₅ η'-phase IMC appeared on all Cu containing UBM cases with Pb/Sn and Bi/Sn solders and the Cu ₃Sn ϵ-phase was detected only with Pb/Sn solder bumps. The Ni₃Sn₄ IMC was found to be the main IMC phase between Ni and solder. The Ni₃Sn secondary IMC was also detected on the electroless Ni UBM with PbSn solder after ten times reflow. Through the bump shear test, Al/NiV/Cu, Al/elNi/Au, and Al/Ti/elCu UBMs showed good stability with Bi/Sn and Pb/Sn solder in terms of metallurgical aspects     

回流次数对Sn3.8Ag0.7Cu-xNi/Ni焊点的影响

研究了复合无铅焊料Sn3.8Ag0.7Cu-xNi(x=0.5,1.0,2.0)与Au/Ni/Cu焊盘在不同回流次数下形成的焊点的性能.结果表明,Ni颗粒增强的复合焊料具有良好的润湿性能,熔点小于222℃;X为0.5的焊料界面IMC由针状(CuNi)6Sn5演化为双层IMC,即多面体状化合物(CuNi)6Sn5和回飞棒...     

Reliability study of new SnZnAl lead-free solders used in CSP packages

We have implemented a company-wide effort to progressively reduce the use of Pb(lead) and eventually eliminate this environmental pollutant from its products. As part of this effort, it has developed a new lead-free solder that consisting of Sn(tin), Zn(zinc), and Al(aluminum) and yet offers superior productivity and joint reliability. The new lead-free solder has a melting point equivalent to that of a SnPb eutectic solder, and enables devices to be packaged at a lower temperature than with the increasingly popular Sn(tin), Ag(silver), Cu(copper) solder. Thus, the new lead-free solder accelerates the elimination of Pb from products. we have already used printed circuit boards containing the new lead-free solder in some products, and plans to extend its use to other products.We further mounted SnZnAl solder balls onto Cu/Ni(nickel)/Au(gold) plated polyimide substrate at a joining temperature of 215 °C for CSP applications. It was confirmed that the joint interface between soldered ball and substrate at the initial stage was made of 2-layered compounds, i.e., AuZnSn on soldered side and ZnSnNi on substrate side. After 1000 h aging at 150 °C, the two layers compounds become one layer of ZnSnNiAu compound. No strength deterioration of Cu/Ni/Au/SnZnAl after the 1300 h shelf test was detected in the ball shear strength compared with the initial value. This paper describes the characteristics of the new lead-free solder and the results of a study on its solder ball CSP package.     

Intermetallics Characterization of Lead-Free Solder Joints under Isothermal Aging

Solder interconnect reliability is influenced by environmentally imposed loads, solder material properties, and the intermetallics formed within the solder and the metal surfaces to which the solder is bonded. Several lead-free metallurgies are being used for component terminal plating, board pad plating, and solder materials. These metallurgies react together and form intermetallic compounds (IMCs) that affect the metallurgical bond strength and the reliability of solder joint connections. This study evaluates the composition and extent of intermetallic growth in solder joints of ball grid array components for several printed circuit board pad finishes and solder materials. Intermetallic growth during solid state aging at 100°C and 125°C up to 1000 h for two solder alloys, Sn-3.5Ag and Sn-3.0Ag-0.5Cu, was investigated. For Sn-3.5Ag solder, the electroless nickel immersion gold (ENIG) pad finish was found to result in the lowest IMC thickness compared to immersion tin (ImSn), immersion silver (ImAg), and organic solderability preservative (OSP). Due to the brittle nature of the IMC, a lower IMC thickness is generally preferred for optimal solder joint reliability. A lower IMC thickness may make ENIG a desirable finish for long-life applications. Activation energies of IMC growth in solid-state aging were found to be 0.54 ± 0.1 eV for ENIG, 0.91 ± 0.12 eV for ImSn, and 1.03 ± 0.1 eV for ImAg. Cu₃Sn and Cu₆Sn₅ IMCs were found between the solder and the copper pad on boards with the ImSn and ImAg pad finishes. Ternary (Cu,Ni)₆Sn₅ intermetallics were found for the ENIG pad finish on the board side. On the component side, a ternary IMC layer composed of Ni-Cu-Sn was found. Along with intermetallics, microvoids were observed at the interface between the copper pad and solder, which presents some concern if devices are subject to shock and vibration loading.     

Lead-free chip scale packages: assembly and drop test reliability

Three underfill options compatible with lead-free assembly have been evaluated: capillary underfill, fluxing underfill, and corner bond underfill. Chip scale packages (CSPs) with eutectic Sn/Pb solder were used for control samples. Without underfill, lead-free and Sn/Pb eutectic drop test results were comparable. Capillary flow underfills, dispensed and cured after reflow, are commonly used in CSP assembly with eutectic Sn/Pb solder. With capillary flow underfill, the drop test results were significantly better with lead-free solder assembly than with Sn/Pb eutectic. Fluxing underfill is dispensed at the CSP site prior to CSP placement. No solder paste is printed at the site. The CSP is placed and reflowed in a standard reflow cycle. A new fluxing underfill developed for compatibility with the higher lead-free solder reflow profiles was investigated. The fluxing underfill with lead-free solder yielded the best drop test results. Corner bond underfill is dispensed as four dots corresponding to the four corners of the CSP after solder paste print, but before CSP placement. The corner bond material cures during the reflow cycle. It is a simpler process compared to capillary or fluxing underfill. The drop test results with corner bond were intermediate between no underfill and capillary underfill and similar for both lead-free and Sn/Pb eutectic solder assembly. The effect of aging on the drop test results with lead-free solder and either no underfill or corner bond underfill was studied. Tin/lead solder with no underfill was used for control. This test was to simulate drop performance after the product has been placed in service for some period of time. There was degradation in the drop test results in all cases after 100 and 250 h of storage at 125/spl deg/C prior to the drop test. The worst degradation occurred with the lead-free solder with no underfill.     

The influence of temperature and humidity on printed wiring board surface finishes: Immersion tin vs organic azoles

Substitution of lead-free solders in electronic assemblies requires changes in the conventional Sn:Pb finishes on substrates and component leads to prevent contamination of the candidate lead-free solder. Options for solderability preservative coatings on the printed wiring board include organic (azole or rosin/resin based) films and tin-based plated metallic coatings. This paper compares the solderability performance and corrosion protection effectiveness of electroless tin coatings vs organic azole films after exposure to a series of humidity and thermal cycling conditions. The solderability of immersion tin is directly related to the tin oxide growth on the surface and is not affected by the formation of SnCu intermetallic phases as long as the intermetallic phase is underneath a protective Sn layer. Thin azole films decompose upon heating in the presence of oxygen and lead to solderability degradation. Evaluations of lead-free solder pastes for surface mount assembly applications indicate that immersion tin significantly improves the spreading of Sn:Ag and Sn:Bi alloys as compared to azole surface finishes.