Analysis and cost optimization of the triple‐pressure steam‐reheat gas‐reheat gas‐recuperated combined power cycle

Increasing the inlet temperature of gas turbine (TIT) and optimization are important methods for improving the efficiency and power of the combined cycle. In this paper, the triple‐pressure steam‐reheat gas‐reheat recuperated combined cycle (the Regular Gas‐Reheat cycle) was optimized relative to its operating parameters, including the temperature differences for pinch points (δT_PP). The optimized triple‐pressure steam‐reheat gas‐reheat recuperated combined cycle (the Optimized cycle) had much lower δT_PP than that for the Regular Gas‐Reheat cycle so that the area of heat transfer of the heat recovery steam generator (HRSG) of the Optimized cycle had to be increased to keep the same rate of heat transfer. For the same mass flow rate of air, the Optimized cycle generates more power and consumes more fuel than the Regular Gas‐Reheat cycle. An objective function of the net additional revenue (the saving of the optimization process) was defined in terms of the revenue of the additional generated power and the costs of replacing the HRSG and the additional fuel. Constraints were set on many operating parameters such as the minimum temperature difference for pinch points (δT_PPm), the steam turbines inlet temperatures and pressures, and the dryness fraction at steam turbine outlet. The net additional revenue was optimized at 11 different maximum values of TIT using two different methods: the direct search and variable metric. The performance of the Optimized cycle was compared with that for the Regular Gas‐Reheat cycle and the triple‐pressure steam‐reheat gas‐reheat recuperated reduced‐irreversibility combined cycle (the Reduced‐Irreversibility cycle). The results indicate that the Optimized cycle is 0.17–0.35 percentage point higher in efficiency and 5.3–6.8% higher in specific work than the Reduced‐Irreversibility cycle, which is 2.84–2.91 percentage points higher in efficiency and 4.7% higher in specific work than the Regular Gas‐Reheat cycle when all cycles are compared at the same values of TIT and δT_PPm. Optimizing the net additional revenue could result in an annual saving of 33.7 million US dollars for a 481 MW power plant. The Optimized cycle was 3.62 percentage points higher in efficiency than the most efficient commercially available H‐system combined cycle when compared at the same value of TIT. Copyright © 2007 John Wiley & Sons, Ltd.     

Modeling,numerical optimization,and irreversibility reduction of a triple-pressure reheat combined cycle

The main methods for improving the efficiency of the combined cycle are: increasing the inlet temperature of the gas turbine (TIT), reducing the irreversibility of the heat recovery steam generator (HRSG), and optimization. In this paper, modeling and optimization of the triple-pressure reheat combined cycle as well as irreversibility reduction of its HRSG are considered. Constraints were set on the minimum temperature difference for pinch points (PP_m), the temperature difference for superheat approach, the steam turbine inlet temperature and pressure, the stack temperature, and the dryness fraction at steam turbine outlet. The triple-pressure reheat combined cycle was optimized at 41 different maximum values of TIT using two different methods; the direct search and the variable metric. A feasible technique to reduce the irreversibility of the HRSG of the combined cycle was introduced. The optimized and the reduced-irreversibility triple-pressure reheat combined cycles were compared with the regularly designed triple-pressure reheat combined cycle, which is the typical design for a commercial combined cycle. The effects of varying the TIT on the performance of all cycles were presented and discussed. The results indicate that the optimized triple-pressure reheat combined cycle is up to 1.7% higher in efficiency than the reduced-irreversibility triple-pressure reheat combined cycle, which is 1.9–2.1% higher in efficiency than the regularly designed triple-pressure reheat combined cycle when all cycles are compared at the same values of TIT and PP_m. The optimized and reduced-irreversibility combined cycles were compared with the most efficient commercially available combined cycle at the same value of TIT.     

Enhancing the efficiency and power of the triple-pressure reheat combined cycle by means of gas reheat, gas recuperation, and reduction of the irreversibility in the heat recovery steam generator

The main methods for improving the efficiency or power of the combined cycle are: increasing the inlet temperature of the gas turbine (TIT), inlet air-cooling, applying gas reheat, steam or water injection into the gas turbine (GT), and reducing the irreversibility of the heat recovery steam generator (HRSG). In this paper, gas reheat with recuperation was applied to the regular triple-pressure steam-reheat combined cycle (the Regular cycle) by replacing the GT unit with a recuperated gas-reheat GT unit (requires two gas turbines, gas recuperator, and two combustion chambers). The Regular cycle with gas-reheat and gas-recuperation (the Regular Gas Reheat cycle) was modeled including detailed modeling of the combustion and GT cooling processes and a feasible technique to reduce the irreversibility of its HRSG was introduced. The Regular Gas Reheat cycle and the Regular Gas Reheat cycle with reduced-irreversibility HRSG (the Reduced Irreversibility cycle) were compared with the Regular cycle, which is the typical design for a commercial combined cycle. The effects of varying the TIT on the performances of all cycles were presented and discussed. The results indicate that the Reduced Irreversibility cycle is 1.9–2.15 percentage points higher in efficiency and 3.5% higher in the total specific work than the Regular Gas Reheat cycle, which is 3.3–3.6 percentage points higher in efficiency and 22–26% higher in the total specific work than the Regular cycle. The Regular Gas Reheat and Reduced Irreversibility cycles are 1.18 and 3.16 percentage points; respectively, higher in efficiency than the most efficient commercially-available combined cycle at the same value of TIT. Economic analysis was performed and showed that applying gas reheat with recuperation to the Regular cycle could result in an annual saving of 10.2 to 11.2 million US dollars for a 339 MW to 348 MW generating unit using the Regular cycle and that reducing the irreversibility of the HRSG of the Regular Gas Reheat cycle could result in an additional annual saving of 11.8 million US dollars for a 439 MW generating unit using the Regular Gas Reheat cycle.     

Modeling,numerical optimization,and irreversibility reduction of a dual-pressure reheat combined-cycle

Optimizing the gas-turbine combined-cycle is an important method for improving its efficiency. In this paper, a dual-pressure reheat combined-cycle was modeled and optimized for 80 cases. Constraints were set on the minimum temperature-difference for pinch points (PP_m), superheat approach temperature-difference, steam-turbine inlet temperature and pressure, stack temperature, and dryness fraction at the steam-turbine’s outlet. The dual-pressure reheat combined-cycle was optimized using two different methods; the direct search and the variable metric. A technique to reduce the irreversibility of the steam generator of the combined cycle was introduced. The optimized and the reduced-irreversibility dual-pressure reheat combined-cycles were compared with the regularly-designed dual-pressure reheat combined-cycle, which is the typical design for a commercial combined-cycle. The effects of varying the inlet temperature of the gas turbine (TIT) and PP_m on the performance of all cycles were presented and discussed. The results indicated that the optimized combined-cycle is up to 1% higher in efficiency than the reduced-irreversibility combined-cycle, which is 2–2.5% higher in efficiency than the regularly-designed combined-cycle when compared for the same values of TIT and PP_m. The advantages of the optimized and reduced-irreversibility combined-cycles were manifested when compared with the most efficient commercially-available combined cycle at the same value of TIT.     

Effects of evaporative inlet and aftercooling on the recuperated gas turbine cycle

Inlet air cooling and cooling of the compressor discharge using water injection boost both efficiency and power of gas turbine cycles. Four different layouts of the recuperated gas turbine cycle are presented. Those layouts include the effect of evaporative inlet and aftercooling (evaporative cooling of the compressor discharge). A parametric study of the effect of turbine inlet temperature (TIT), ambient temperature, and relative humidity on the performance of all four layouts is investigated. The results indicate that as TIT increases the optimum pressure ratio increases by 0.45 per 100 K for the regular recuperated cycle and by 1.4 per 100 K for the recuperated cycle with evaporative aftercooling. The cycles with evaporative aftercooling have distinctive pattern of performance curves and higher values of optimum pressure ratios. The results also showed that evaporative cooling of the inlet air could boost the efficiency by up to 3.2% and that evaporative aftercooling could increase the power by up to about 110% and cycle efficiency by up to 16%.     

Thermal‐economic analysis of a transcritical Rankine power cycle with reheat enhancement for a low‐grade heat source

A thermal‐economic analysis of a transcritical Rankine power cycle with reheat enhancement using a low‐grade industrial waste heat is presented. Under the identical operating conditions, the reheat cycle is compared to the non‐reheat baseline cycle with respect to the specific net power output, the thermal efficiency, the heat exchanger area, and the total capital costs of the systems. Detailed parametric effects are investigated in order to maximize the cycle performance and minimize the system unit cost per net work output. The main results show that the value of the optimum reheat pressure maximizing the specific net work output is approximately equal to the one that causes the same expansion ratio across each stage turbine. Relative performance improvement by reheat process over the baseline is augmented with an increase of the high pressure but a decrease of the turbine inlet temperature. Enhancement for the specific net work output is more significant than that for the thermal efficiency under each condition, because total heat input is increased in the reheat cycle for the reheat process. The economic analysis reveals that the respective optimal high pressures minimizing the unit heat exchanger area and system cost are much lower than that maximizing the energy performance. The comparative analysis identifies the range of operating conditions when the proposed reheat cycle is more cost effective than the baseline. Copyright © 2012 John Wiley & Sons, Ltd.     

Energy and exergy analysis of steam cooled reheat gas–steam combined cycle

This paper deals with parametric energy and exergy analysis of reheat gas–steam combined cycle using closed-loop-steam-cooling. Of the blade cooling techniques, closed-loop-steam-cooling has been found to be superior to air-film cooling. The reheat gas–steam combined cycle plant with closed-loop-steam-cooling exhibits enhanced thermal efficiency (around 62%) and plant specific work as compared to basic steam–gas combined cycle with air-film cooling as well as closed-loop-steam cooling. Further, with closed-loop-steam-cooling, the plant efficiency, reaches an optimum value in higher range of compressor pressure ratio as compared to that in film air-cooling. It has also been concluded that reheat pressure is an important design parameter and its optimum value gives maximum plant efficiency.Component-wise inefficiencies of steam cooled-reheat gas–steam combined cycle based on the second-law-model (exergy analysis) have been found to be the maximum in combustion-chamber (≈30%), followed by that in gas turbine (≈4%).     

Thermodynamic performance assessment of an indirect intercooled reheat regenerative gas turbine cycle with inlet air cooling and evaporative aftercooling of the compressor discharge

This study provides a computational analysis to investigate the effects of cycle pressure ratio, turbine inlet temperature (TIT), and ambient relative humidity (φ) on the thermodynamic performance of an indirect intercooled reheat regenerative gas turbine cycle with indirect evaporative cooling of the inlet air and evaporative aftercooling of the compressor discharge. Combined first and second‐law analysis indicates that the exergy destruction in various components of gas turbine cycles is significantly affected by compressor pressure ratio and turbine inlet temperature, and is not at all affected by ambient relative humidity. It also indicates that the maximum exergy is destroyed in the combustion chamber; which represents over 60% of the total exergy destruction in the overall system. The net work output, first‐law efficiency, and the second‐law efficiency of the cycle significantly varies with the change in the pressure ratio, turbine inlet temperature and ambient relative humidity. Results clearly shows that performance evaluation based on first‐law analysis alone is not adequate, and hence more meaningful evaluation must include second‐law analysis. Decision makers should find the methodology contained in this paper useful in the comparison and selection of gas turbine systems. Copyright © 2006 John Wiley & Sons, Ltd.     

Thermodynamic assessment of advanced SOFC-blade cooled gas turbine hybrid cycle

This paper focuses on novel integration of high temperature solid oxide fuel cell coupled with recuperative gas turbine (with air-film cooling of blades) based hybrid power plant (SOFC-blade cooled GT). For realistic analysis of gas turbine cycle air-film blade cooling technique has been adopted. First law thermodynamic analysis investigating the combine effect of film cooling of blades, SOFC, applied to a recuperated gas turbine cycle has been reported. Thermodynamic modeling for the proposed cycle has been presented. Results highlight the influence of film cooling of blades and operating parameters of SOFC on various performance of SOFC-blade cooled GT based hybrid power plant. Moreover, parametric investigation has also been done to examine the effect of compressor pressure ratio, turbine inlet temperature, on hybrid plant efficiency and plant specific work. It has been found that on increasing turbine inlet temperature (TIT) beyond a certain limit, the efficiency of gas turbine starts declining after reaching an optimum value which is compensated by continuous increase in SOFC efficiency with increase in operating temperature. The net result is higher performance of hybrid cycle with increase in maximum cycle temperature. Furthermore, it has been observed that at TIT 1600 K and compression ratio 20, maximum efficiency of 73.46% can been achieved.     

Energy and exergy analyses of a CFB‐based indirectly fired combined cycle power generation system

Combined cycle configuration has the ability to use the waste heat from the gas turbine exhaust gas using the heat recovery steam generator for the bottoming steam cycle. In the current study, a natural gas‐fired combined cycle with indirectly fired heating for additional work output is investigated for configurations with and without reheat combustor (RHC) in the gas turbine. The mass flow rate of coal for the indirect‐firing mode in circulating fluidized bed (CFB) combustor is estimated based on fixed natural gas input for the gas turbine combustion chamber (GTCC). The effects of pressure ratio, gas turbine inlet temperature, inlet temperatures to the air compressor and to the GTCC on the overall cycle performance of the combined cycle configuration are analysed. The combined cycle efficiency increases with pressure ratio up to the optimum value. Both efficiency and net work output for the combined cycle increase with gas turbine inlet temperature. The efficiency decreases with increase in the air compressor inlet temperature. The indirect firing of coal shows reduced use with increase in the turbine inlet temperature due to increase in the use of natural gas. There is little variation in the efficiency with increase in GTCC inlet temperature resulting in increased use of coal. The combined cycle having the two‐stage gas turbine with RHC has significantly higher efficiency and net work output compared with the cycle without RHC. The exergetic efficiency also increases with increase in the gas turbine inlet temperature. The exergy destruction is highest for the CFB combustor followed by the GTCC. The analyses show that the indirectly fired mode of the combined cycle offers better performance and opportunities for additional net work output by using solid fuels (coal in this case). Copyright © 2009 John Wiley & Sons, Ltd.     

Parameter optimization study on SOFC‐MGT hybrid power system

This paper mainly studied the solid oxide fuel cell (SOFC)–micro gas turbine (MGT) hybrid power system. The key parameters that greatly influence the overall system performance have been studied and optimized. The thermodynamic potential of improving the hybrid system performance by integrating SOFC with the advanced thermal cycle system is analyzed. The optimization rules of main parameters of SOFC‐MGT hybrid power system with the turbine inlet temperature (TIT) of MGT as a constraint condition are revealed. The research results show that TIT is a key parameter that limits the electrical efficiency of hybrid power system. With the increase of the cell number, both the power generation efficiency of the hybrid cycle power system and TIT increase. Regarding the hybrid system with the fixed cell number, in order to get a higher electrical efficiency, the operating temperature of SOFC should be enhanced as far as possible. However, the higher operating temperature will result in the higher TIT. Increasing of fuel utilization factor is an effective measure to improve the performance of hybrid system. At the same time, TIT increases slightly. Both the electrical efficiency of hybrid power system and TIT reduce with the increase of the ratio of steam to carbon. The achievements obtained from this paper will provide valuable information for further study on SOFC‐MGT hybrid power system with high efficiency. Copyright © 2010 John Wiley & Sons, Ltd.     

Thermodynamic optimization of reheat regenerative thermal-power plants

A first- and second-law procedure for the optimization of the reheat pressure level in reheat regeneration thermal-power plants is presented. The procedure is general in form and is applied for a thermal-power plant having two reheat pressure levels and two open-type feedwater heaters. The second-law efficiency of the steam generator, turbine cycle and plant are evaluated and optimized. The irreversibilities in the different components of the steam generator and turbine cycle sections are evaluated and discussed. Additional constraints such as the steam qualities at the exits of the different turbine stages are considered.     

Comprehensive evaluation of a CO2‐capturing high‐efficiency power generation system for utilizing waste heat from factories

It is becoming more important to realize CO₂‐capturing power generation systems (PGSs) for drastically decreasing an amount of CO₂ emission into the atmosphere. However, net power generation efficiency (NPGE) of a CO₂‐capturing system has been considered to be greatly deteriorated, since capturing CO₂ requires extra energy. This paper proposes a new CO₂‐capturing PGS that has a high‐efficient NPGE by utilizing waste heat from factories. As an example of a waste heat, exhaust gas with temperature 200°C from refuse incinerator plants is adopted. In the proposed system, the temperature of saturated steam produced by utilizing the waste heat is raised by combusting fuel with the use of pure oxygen in a combustor, and is used as the main working fluid of a gas turbine PGS. It is estimated that the proposed system has a fuel‐to‐electricity NPGE of 59.3%, when turbine inlet temperature (TIT) is assumed to be 1000°C. The economics of the proposed system is also evaluated and the CO₂ reduction cost is estimated to be small; 4.16 U.S. $ t⁻¹ CO₂ compared with 32.1 U.S. $ t⁻¹ CO₂ for a conventional steam turbine PGS. It is shown that CO₂‐capturing is not cost consuming but becomes to be profitable owing to improved power generation characteristics, when its TIT is increased from 1000 to 1200°C. Copyright © 2009 John Wiley & Sons, Ltd.     

Analysis of parameters affecting the performance of gas turbines and combined cycle plants with vapor absorption inlet air cooling

The integration of an aqua‐ammonia inlet air‐cooling scheme to a cooled gas turbine‐based combined cycle has been analyzed. The heat energy of the exhaust gas prior to the exit of the heat recovery steam generator has been chosen to power the inlet air‐cooling system. Dual pressure reheat heat recovery steam generator is chosen as the combined cycle configuration. Air film cooling has been adopted as the cooling technique for gas turbine blades. A parametric study of the effect of compressor–pressure ratio, compressor inlet temperature, turbine inlet temperature, ambient relative humidity, and ambient temperature on performance parameters of plants has been carried out. It has been observed that vapor absorption inlet air cooling improves the efficiency of gas turbine by upto 7.48% and specific work by more than 18%, respectively. However, on the adoption of this scheme for combined cycles, the plant efficiency has been observed to be adversely affected, although the addition of absorption inlet air cooling results in an increase in plant output by more than 7%. The optimum value of compressor inlet temperature for maximum specific work output has been observed to be 25 °C for the chosen set of conditions. Further reduction of compressor inlet temperature below this optimum value has been observed to adversely affect plant efficiency. Copyright © 2013 John Wiley & Sons, Ltd.     

Advances in super critical power generation 2006

Abstract

European efforts to start substantial improvements of the performance of well established supercritical coal fired power technology named the AD700 project started in the mid 1990s. Major targets were development of austenitic materials and nickel based superalloys for the hottest sections of boilers, steam lines and turbines. Other targets were development of boiler and turbine designs for the more advanced conditions and finally economic viability of the AD700 technology has been investigated. The project has been very successful and 40 partners from the European power industry have worked together in several projects cofunded by the European Commission for >10 years. Procurement of mature and commercially optimised AD700 plant could take place around 2015. The investigated nickel based materials have shown very high creep strengths but they have also shown to be very hard to manufacture, and more efforts to define new machining lines are being started. Ongoing tests indicate that the developed austenitic material will fulfil its creep strength target and is now ready for commercialisation. Development works on boiler and turbine designs for the advanced steam conditions have also been successfully completed but they also clearly indicate that further development work on improved ferritic steel for furnace walls is important. Conventional development of the steam cycles is based on new improved materials, which open for higher steam temperatures and efficiencies whereas other thermodynamic tools are only slowly being accepted. However, in the present paper a proposal for steam cycle improvements not based on higher steam temperatures is presented. The improved cycle is named the master cycle (MC) and it is based on a revision of the double reheat steam cycle where the bleeds of the intermediate pressure (IP) turbines have been moved to a feed pump turbine bleeding on the first cold reheat line. Elsam has established protection of a patent for the MC in a number of countries. At constant main and reheat steam temperatures, the MC offers solid heat rate improvements of ～3·5% compared with single reheat cycles and a seawater cooled plant based on the MC could reach a net efficiency of 50%. This would mean robust improvement of competitiveness, less CO₂ per MW h being generated and a more sustainable use of the coal resources. In the future, the net efficiency will continue to increase and a sea water cooled 800 MW AD700 power plant to start commercial operation around 2020 might reach a net efficiency around 55% based on the MC. However, pressure on energy resources will continue and even increase in future, so that the need for more effective and sustainable power stations will also continue, and there are no signs that development of more advanced materials and water/steam cycles will stop in foreseeable future.     

Energetic and exergetic analysis of a hybrid combined‐nuclear power plant

Combined‐cycle power plants are currently preferred for new power generation plants worldwide. The performance of gas‐turbine engines can be enhanced at constant turbine inlet temperatures with the addition of a bottoming waste‐heat recovery cycle. This paper presents a study on the energy and exergy analysis of a novel hybrid Combined‐Nuclear Power Plant (HCNPP). It is thus interesting to evaluate the possibility of integrating the gas turbine with nuclear power plant of such a system, utilizing virtually free heat. The integration arrangement of the AP600 NPP steam cycle with gas turbines from basic thermodynamic considerations will be described. The AP600 steam cycle modifications to combine with the gas turbines can be applied to other types of NPP. A simple modeling of Alstom gas turbines cycle, one of the major combined‐cycle steam turbines manufacturers, hybridized with a nuclear power plant from energetic and exergetic viewpoint is provided. The Heat Recovery Steam Generator (HRSG) has single steam pressure without reheat, one superheater and one economizer. The thermodynamic parameters of the working fluids of both the gas and the steam turbines cycles are analyzed by modeling the thermodynamic cycle using the Engineering Equation Solver (EES) software. In case of hybridizing, the existing Alstom gas turbine with a pressurized water nuclear power plants using the newly proposed novel solution, we can increase the electricity output and efficiency significantly. If we convert a traditional combined cycle to HCNPP unit, we can achieve about 20% increase in electricity output. This figure emphasizes the significance of restructuring our power plant technology and exploring a wider variety of HCNPP solutions. Copyright © 2011 John Wiley & Sons, Ltd.     

Thermoenvironomic evaluation of simple,intercooled, STIG,and ISTIG cycles

Low‐technology cycle modifications available for improving gas turbine performance are still largely unexploited. Among those proven modifications, steam injection is found to be the most effective in boosting both the output capacity and thermal efficiency while reducing NO_x emissions. It further improves part load performance under varying ambient conditions. Intercooling is another low‐technology modification which can improve performance of simple and steam injected gas turbine cycles. Because of the uncertainties relating to an efficiency comparison of steam injected and simple cycle designs, the decision as to whether it is worthwhile to give more emphasis to steam injected cycles should be made on grounds other than efficiency alone. Therefore, this study comparatively evaluates simple, intercooled, steam injected (STIG), and intercooled steam injected (ISTIG) gas turbine cycles from the points of efficiency, network output, economics, and pollutant emissions using an advanced validated thermoenvironomic model. Optimum cycle parameters are investigated. Economic feasibility of steam injection and intercooling on simple and intercooled cycles are evaluated using an updated plant cost data. Total and environmental costs as well as profit of the plant owner are estimated for varying fuel costs and varying cycle parameters such as pressure, steam injection, and equivalence ratio. Results of our analysis based on the characteristic cycle parameters show that network output increases up to 22.2% and 14% respectively, when steam injection is implemented on simple and intercooled gas turbine cycles which correspond to up to 6.7% and 4.4% decrease in specific fuel consumption. Steam injection decreases NO_x emissions of simple and intercooled cycles up to 67.2% and 65.2% respectively, and provides up to approximately 126.3% increase in net profit of intercooled cycle at the expense of an increase in total cost by 3.3%.     

Performance analysis of open cycle gas turbines

In this study, the performance of ideal open cycle gas turbine system was examined based on its thermodynamic analysis. The effects of some parameters, such as compressor inlet temperature (CIT), pressure ratio (PR) and the turbine inlet temperature (TIT), on the performance parameters of open cycle gas turbine were discussed. The turbine net power output, the thermal efficiency and the fuel consumption of the turbine were taken as the performance parameters. The values of these parameters were calculated using some basic cycle equations and variables values of thermodynamic properties. Other variables such as lower heating value, combustion efficiency and isentropic efficiencies of compressor and turbine were assumed to be constant. The result showed that the net power output and the thermal efficiency increased by a decrease in the CIT and increase in the TIT and PR values. If it is aimed to have a high net power output and the thermal efficiency for the turbine, the CIT should be chosen as low as possible and the TIT should be chosen as high as possible. Copyright © 2008 John Wiley & Sons, Ltd.     

Characteristic evaluation of a CO2‐capturing repowering system based on oxy‐fuel combustion and exergetic flow analyses for improving efficiency

A CO₂‐capturing H₂O turbine power generation system based on oxy‐fuel combustion method is proposed to decrease CO₂ emission from an existing thermal power generation system (TPGS) by utilizing steam produced in the TPGS. A high efficient combined cycle power generation system (CCPS) with reheat cycle is adopted as an example of existing TPGSs into which the proposed system is retrofitted. First, power generation characteristics of the proposed CO₂‐capturing system, which requires no modification of the CCPS itself, are estimated. It is shown through simulation study that the proposed system can reduce 26.8% of CO₂ emission with an efficiency decrease by 1.20% and an increase power output by 23.2%, compared with the original CCPS. Second, in order to improve power generation characteristics and CO₂ reduction effect of the proposed system, modifications of the proposed system are investigated based on exergetic flow analyses, and revised systems are proposed based on the obtained results. Finally, it is shown that a revised proposed system, which has the same turbine inlet temperature as the CCPS, can increase power output by 33.6%, and reduce 32.5% of CO₂ emission with exergetic efficiency decrease by 1.58%, compared with the original CCPS. Copyright © 2010 John Wiley & Sons, Ltd.     

Humid air turbine cycle blade cooling exergetic analysis

Starting from the first steam injection cycles (GE‐STIG; Cheng), the technique of increasing gas turbine performances by injecting water/steam somewhere before the combustion chamber, has shown very interesting results for power and efficiency increase and for NO_x emissions. Very interesting performances are achieved by evaporative cycles, such as the HAT (Humid Air Turbine), which is capable of achieving 50% conversion efficiency with lower investment costs compared to combined cycles. Other advantages of the steam injected cycle include the power modulation that is possible by varying the injected steam flow rate, keeping the maximum temperature constant. In particular, for the HAT cycle, it is possible to choose different temperature, pressure and compositions for the blade cooling fluid, depending on the bleed point. In this paper, a second law analysis of the HAT cycle and its components, has been performed. In particular, the exergetic analysis of blade cooling has been carefully analysed. Copyright © 1999 John Wiley & Sons, Ltd.