Numerical comparison of premixed H2/air combustion characteristic of three types of micro cavity-combustors with guide vanes,bluff body,guide vanes and bluff body respectively

Micro-scale combustion is facing the problems of ignition difficulty, combustion instability, and low combustion efficiency. Therefore, it is necessary to improve the combustion characteristics in micro-combustor to expand the application range of micro-combustor. Focusing on the problem of the weak preheating effect of the micro cavity-combustor, the guide vanes are constructed to enhance the combustion near the cavity, and further combine with the bluff body to enhance combustion. The combustion characteristics of three types of cavity combustors with guide vanes (CCGV), bluff body (CCBB), bluff body, and guide vanes (CCGB) respectively are compared and analyzed under different inlet velocities (8–32 m/s), equivalence ratios (0.6–1.4), and wall materials (quartz glass, steel, and SiC). Results show that the guide vanes can greatly improve the combustion intensity near the cavity and improve the combustion stability of the cavity combustor. The combustion efficiency of CCGV and CCGB are increased by 43.04% and 85.96% respectively than CCBB when the inlet velocity is 32 m/s. The reaction heat of CCGV is 244.5 W when inlet velocity is 32 m/s, which is 0.55 times and 1.57 times that of CCGV and CCBB, respectively. The temperature uniformity and mean temperature of the outer wall of CCGV and CCGB both are better than that of CCGB. The combustion efficiency of CCGB is the highest among three combustors under the same equivalence ratio, especially when the equivalence ratio is less than 1. The reaction intensity in the cavity of the CCGV and CCGB with steel wall material is highest than that of the combustor with the other two wall materials. Wall materials with high thermal conductivity have a better preheating effect. Compared with quartz as the wall material, the mean temperature of the external wall of CCGV and CCGB using steel and silicon carbide as the wall material both increase by more than 130 K, and the wall heat loss both increase by more than 50%.     

Experimental and numerical investigations of hydrogen–air premixed combustion in a converging–diverging micro tube

Experimental and numerical studies of hydrogen–air premixed combustion in a converging–diverging micro tube with inner diameters of the inlet, throat, and outlet of 2, 1, and 2 mm, respectively, have been performed to study the combustion and flame characteristics. The influences of the equivalence ratio (Φ) and inlet velocity (v_in) are investigated. The experiments reveal that the v_in range for stable combustion—between 3.4 and 41.4 m/s—was significantly expanded, particularly when Φ = 1.4. This effect can primarily be attributed to the converging–diverging structure. As Φ increased, both the wall and the flame temperatures exhibited an increasing–decreasing trend; the largest heat loss ratio occurred at Φ = 1.0. The ignition position initially moved upstream and then moved downstream. The flame thickness increased and then decreased, reaching its peak value at Φ = 1.2. The flame length decreased monotonously. As v_in increased, the wall temperature increased, the flame temperature decreased, and the flame moved downstream to grow thicker and longer.     

Effect of multiple bluff bodies on hydrogen/air combustion characteristics and thermal properties in micro combustor

The bluff body is commonly used to improve micro combustion. The micro combustor with multiple rectangular bluff bodies in a single row was proposed. The effects of bluff bodies on H₂/air combustion characteristics were numerically studied. The temperature distributions, ignition position, combustion efficiency and blow-out limit were investigated via changing the total width and number of bluff bodies. The results show that the combined use of multiple bluff bodies can further expand the blow-out limit of H₂/Air. The effect of high temperature and viscous force on the flow velocity is main factors for the flame morphology. When the total width of bluff bodies is 2 mm, the blow-out limit decreases with the increase of bluff body number. When the total width of bluff bodies is 4 mm and 6 mm, the blow-out limit increases with the increase of the number of bluff bodies. With the increase of inlet velocity, the complete combustion efficiency decreases. The combustion efficiency in the combustor with wider blow-out limit decreases more slowly. It indicates that the combustor with multi-bluff bodies is more suitable for the operation conditions with high flow velocity.     

Combustion characteristics and thermal enhancement of premixed hydrogen/air in micro combustor with pin fin arrays

Targeted at improving the combustion stability and enhancing heat transfer in micro combustor, the combustion characteristics and thermal performance of micro combustor with pin fin arrays are numerically investigated by employing detail H₂/O₂ reaction mechanism. It is shown that the micro combustor with staggered pin fin arrays exhibits the highest average temperature and heat flux of external wall, while the micro combustor with in-line pin fin arrays displays the most uniform temperature distribution of external wall. When the equivalence ratio is 1.1, all micro combustors exhibit the highest mean temperature and heat flux of external wall. The micro combustor materials with high thermal conductivity can not only improve the average temperature and heat flux of external wall, but also enhance heat transfer to the upstream which can preheat the mixed gas. Therefore, the materials with high thermal conductivity, such as red copper and aluminum, can make up for the nonuniform temperature distribution of micro combustor with staggered pin fin arrays, so as to realize uniform high heat flux output of external wall.     

Numerical study on methane/air combustion characteristics in a heat-recirculating micro combustor embedded with porous media

Micro-combustor is a portable power device that can provide energy efficiently, heat recirculating is considered to be an important factor affecting the combustion process. For enhancing the heat recirculating and improving the combustion stability, we proposed a heat-recirculating micro-combustor embedded with porous media, and the numerical simulation was carried out by CFD software. In this paper, the effect of porous media materials, thickness and inlet conditions (equivalence ratio, inlet velocity) on the temperature distribution and exhaust species in the micro combustor are investigated. The results showed that compared with the micro combustor without embedded porous media (MCNPM), micro-combustor embedded with porous media (MCEPM) can improve the temperature uniformity distribution in the radial direction and strengthen the preheating capacity. However, it is found that the embedding thickness of porous media should be reasonably arranged. Setting the thickness of porous media to 15 mm, the combustor can obtain excellent comprehensive capacity of steady combustion and heat recirculating. Compared the thermal performance of Al₂O₃, SiC, and ZrO₂ porous media materials, indicating that SiC due to its strong thermal conductivity, its combustion stabilization and heat recirculating capacity are obviously better than that of Al₂O₃ and ZrO₂. With the porous media embedded in the micro combustor, the combustion has a tempering limit of more than 10 m/s, and the flame is blown out of the porous media area over 100 m/s. The reasonable equivalence ratio of CH₄/air combustion should be controlled within the range of 0.1–0.5, and “super-enthalpy combustion” can be realized.     

A numerical study on combustion and emission characteristics of premixed hydrogen air flames

Main challenges for micro power generators that utilize combustion process for energy production are inadequate residence time, destructive radical wall interactions and intensified heat loss which are mainly rooted from size limitation of such devices. To achieve high and uniform energy output, and bring in a solution to these challenges in an environment friendly manner without any kind of fundamental modification, effect of equivalence ratio on combustion and emission behavior of premixed hydrogen/air flames is numerically investigated in this study. For this purpose, an experimentally tested micro cylindrical combustor model is constructed and premixed hydrogen/air combustion in this model is simulated by varying equivalence ratio between 0.5 and 1.2 to find an optimal equivalence ratio with respect to drawbacks of micro power generators. Combustion and turbulence models implemented in this study are Eddy Dissipation Concept and Standard k-ε models, respectively. A detailed hydrogen/air reaction mechanism which consists of 9 species and 19 steps is employed to accurately gain insight into combustion process. Simulation results show that as the equivalence ratio decreases; centerline temperature distribution gets a lower value and the place where chemical reactions take place moves downstream. The most uniform temperature distribution is achieved between 0.8 and 1.0 equivalence ratios. The highest NO_x formation is at 0.9 equivalence ratio and its mass fraction decreases sharply when the equivalence ratio reduces from 0.9 to 0.5.     

Numerical study on premixed hydrogen/air combustion characteristics and heat transfer enhancement of micro-combustor embedded with pin fins

Aimed at improving the energy output performance of the Microthermal Photovoltaic (MTPV) system, it is necessary to optimize the structure of the micro combustor. In this paper, micro combustor with in-line pin fins arrays (MCIPF) and micro combustor with both end-line pin fins arrays (MCEPF) were presented to realize the efficient combustion and heat transfer enhancement, and the influence of inlet velocity, equivalent ratio, and materials on thermal performance was investigated. The results showed that pin fins embedding is beneficial to improving combustion, and the combustion efficiency of MCIPF and MCEPF reaches 98.5% and 98.7%, which is significantly higher than that of the conventional cylindrical combustor (MCC). However, with the increase of inlet velocity from 8 m/s to 14 m/s, MCIPF exhibits the highest external wall temperature with a range of (1302–1386 K), while MCEPF maintains the best temperature uniformity. As the inlet velocity increases to 10 m/s, the external wall temperature and temperature uniformity reach the optimum. Besides, under the conditions of different equivalence ratios, both external wall temperature and heat flux increases first and then decreases, meanwhile the temperature uniformity of MCEPF is significantly improved compared with that of MCIPF, they all exhibit the highest external wall temperature with an equivalence ratio of 1.1, and the thermal performance is greatly enhanced. By comparing the heat transfer performance of combustors with different materials based on MCEPF, it is interesting to find that the application of high thermal conductivity materials can not only increase the external wall temperature, but also improve the temperature uniformity. Therefore, materials with high thermal conductivity such as Aluminum, Red Copper and Silicon Carbide should be selected for application in micro combustors and their components. The current work provides a new design method for the enhanced heat transfer of the micro combustor.     

Numerical investigation of combustion characteristics for hydrogen mixed fuel in a can-type model of the gas turbine combustor

Numerical simulations are performed to analyze the combustion characteristics of propane fuel mixed with different amounts of hydrogen in a can-type combustor. The volume fraction of the hydrogen fuel varies from 0% to 100% in the fuel mixture. The results indicate that the hydrogen enrichment of the fuel significantly affects the flow structure, mixture fraction, and combustion characteristics. An increase in the volume fraction of hydrogen significantly affects the mean mixture fraction distribution, promotes combustion, and increases the flame temperature and the width of the flammable range within the combustor. Therefore, the degree of temperature uniformity at the outlet of the combustor increases with hydrogen enrichment, corresponding to an increase of 49.64% in the uniformity factor. The hydrogen enriched fuel can also reduce the emissions of CO and CO₂, owing to the reduced amount of carbonaceous fuel.     

Thermal performance characteristics of a micro-combustor with swirl rib fueled with premixed hydrogen/air

Outer wall temperature and exergy efficiency of micro-combustor are very essential in determining micro-thermophotovoltaic energy conversion effectiveness. In this study, a swirl rib was designed to improve the thermal efficiency of micro-combustor since a swirl flow can be formed when the hydrogen/air mixture passes through the swirl rib, which increases the residence time and turbulence intensity of the mixture. Effects of position, height, spacing, and shape of the swirl rib on the thermal performance of a cylindrical micro-combustor were investigated numerically. The thermal performance shows different trends with the variation of these geometric parameters, and an optimum mean outer wall temperature of 1260 K is obtained at the distance between the inlet and the rib of 7 mm, the rib height of 1.2 mm and the rib spacing of 0.5 mm, but this optimum setting triggers the large pressure drop that impedes further improvement of the micro-combustor performance. To minimize this effect, three rip shapes including rectangle, trapezoid and inversed trapezoid was designed. The results show that the micro-combustor with trapezoidal rib presents better thermal performance. This study provides theoretical guidance for the optimal design of the hydrogen-fueled micro-combustor.     

Numerical investigation on the self-ignition and combustion characteristics of H2/air in catalytic micro channel

The self-ignition of hydrogen/air is an important process in the micro thermophotovoltaic system. The transient numerical models of gas-phase reaction and catalytic reaction in the various catalytic micro combustors were built and verified. The self-ignition process of gas-phase reaction caused by catalytic reaction in the catalytic micro channel with conventional heat dissipation was studied. The self-ignition process could be divided into four stages, fuel diffusion stage - pure catalytic reaction stage - flame front moving stage - stable combustion stage. The ignition time and temperature limit at different inlet temperatures, inlet velocities and channel heights were analyzed. The results showed that the wall quenching effect, thermal effect and flame propagation effect are dominant at low temperature, medium temperature and high temperature respectively. The catalyst length and the mixture internal energy were the main factor at low inlet velocity and high inlet velocity respectively. The steady-state time was also studied in the various operation conditions. Finally, the catalytic combustion characteristics in the stable combustion stage were analyzed. The influence of inert section length, inlet temperature and inlet velocity on the maximum temperature and fuel conversion ratio were investigated.     

旋流预混燃烧室燃烧特性及排放特性的数值模拟研究

为了综合考察燃气轮机燃烧室在高稳定性、低排放以及燃料适应性等方面的新要求,基于旋流预混燃烧技术,通过三维数值模拟方法开展了甲烷/空气、丙烷/空气预混燃烧特性及排放特性研究。结果表明：在一定的预混气进气质量流量条件下,当量比增大易引发回火,燃烧温度更高,同时NO_x排放指数增大,增加预混气质量流量,可在一定程度上提高回/熄火极限;当量比固定,增加预混气进气质量流量可避免潜在的回火现象,且NO_x排放指数线性降低;旋流器的旋流数增大能形成强旋流,稳定火焰,降低NO_x排放指数,但过大的旋流强度会引发回火现象;相比于甲烷/空气预混燃烧,丙烷/空气预混燃烧温度偏高,NO_x排放指数较大,但回熄火边界更宽,对应更广阔的稳定燃烧区间。     

Numerical investigation into the structural characteristics of a hydrogen dual-swirl combustor with slight temperature rise combustion

For decades, hydrogen has been identified as the most promising potential fuel to replace fossil fuels. In order to fully implement it and to promote the rationality of the design of hydrogen combustion chamber structure, it is very essential to understand the hydrogen/air combustion mechanism based on structural variations. The structural characteristics of a novel dual-swirl burner for hydrogen-air non-premixed combustion was studied numerically in this study. The influences of air distributions, swirling directions and nozzle configurations of the dual-swirl burner were studied, and the combustion performance was evaluated from various aspects. The numerical results showed that there was a trade-off between lower total pressure loss and the risk of fusing when considering air distribution strategies. The co-rotating swirl burner exhibited better uniformity of temperature distribution at the downstream of the combustor. The multi jet orifices showed superior penetration depth than the circular seam. Efficient and stable combustion could be achieved, which was beneficial to improve gas turbine efficiency and stable operation.     

Experimental and numerical investigation on combustion characteristics of premixed hydrogen/air flame in a micro-combustor with a bluff body

Combustion characteristics of lean hydrogen/air mixture in a planar micro-channel with a bluff body were investigated experimentally and numerically. Effects of the inlet velocity and equivalence ratio on the blow-off limit, combustion efficiency and exhaust gas temperature were examined. The results show that the blow-off limit is greatly extended as compared with that of the micro-combustor without a bluff body. Moreover, the blow-off limit increases as the equivalence ratio is increased from 0.4 to 0.6. Furthermore, with the increase of inlet velocity, the flame front is prolonged and becomes narrower, and the high temperature segment of outer wall shifts downstream. In addition, the combustion efficiency and exhaust gas temperature increase first and then decrease with the increase of the inlet velocity. Finally, comparatively high combustion efficiency can be maintained over the whole combustible velocity range at a moderate equivalence ratio.     

Experimental investigation of the stability and emission characteristics of premixed formic acid-methane-air flames in a swirl combustor

Formic acid (FA) is a potential hydrogen energy carrier and low-carbon fuel by reversing the decomposition products, CO₂ and H_2, back to restore FA without additional carbon release. However, FA-air mixtures feature high ignition energy and low flame speed; hence stabilizing FA-air flames in combustion devices is challenging. This study experimentally investigates the flame stability and emission of swirl flames fueled with pre-vaporized formic acid-methane blends over a wide range of formic acid fuel fractions. Results show that by using a swirl combustor, the premixed formic acid-methane-air flames could be stabilized over a wide range of FA fuel fractions, Reynolds numbers, and swirl numbers. The addition of formic acid increases the equivalence ratios at which the flashback and lean blowout occur. When Reynolds number increases, the equivalence ratio at the flashback limit increases, but that decreases at the lean blowout limit. Increasing the swirl number has a non-monotonic effect on stability limits variation because increasing the swirl number changes the axial velocity on the centerline of the burner throat non-monotonically. In addition, emission characteristics were investigated using a gas analyzer. The CO and NO concentrations were below 20 ppm for all tested conditions, which is comparable to that seen with traditional hydrocarbon fuels, which is in favor of future practical applications with formic acid.     

Numerical investigation on implication of innovative hydrogen strut in comparison with multi strut injector on performance and combustion characteristics in a scramjet combustor

Detailed numerical analysis on a cavity-based scramjet combustor is carried out by introducing an innovatively shaped strut and multi strut with backward-facing step to generate intense vorticity, which helps in efficient mixing of fuel and oxidizer. In this study, the flow dynamics with finite volume approach on commercial software Ansys-Fluent 20.0 to solve the compressible two-dimensional fluid flow with RANS equation by considering the density-based solver with SST k- ω turbulent model. The species transport model with volumetric reaction and finite rate/eddy dissipation turbulence chemistry interaction is adopted to study the combustion phenomena. Numerically calculated results are validated with its corresponding experimental results by comparing pressure distribution along the length of the combustor, distribution of H₂ mole fraction for different axial locations of combustors, and it is found that the interaction of the shear shock layer enhances the mixing rate by intensifying turbulence. It is found that the multi strut improves the mixing and combustion efficiency compared with that of the single strut owing to the formation of a significant separation layer, resulting in multiple shocks, vortices, and a larger recirculation zone.     

Numerical investigation of a novel micro combustor with a central and bilateral slotted blunt body

To improve the combustion stability at micro scale, the micro combustor with a central and bilateral slotted blunt body (MCSB) exhibiting significant combustion performance improvement is designed. The new one can not only effectively prevent the flame tip opening, but also exhibit higher combustion efficiency and blown-off limit. Its blown-off limit can reach 756 cm³/s at the flow rate ratio of 0.2 and the bluff body angle of 90°, which is 61.5% higher than that of the conventional one with the blown-off limit of 468 cm³/s. The combustion efficiency improves with the growth of the flow rate ratio, while the blown-off limit of MCSB increases first and then decreases. The blown-off limit of MCSB with the bluff body angle of 90° reaches to the peak value of 792 cm³/s at the flow rate ratio of 0.15. Moreover, the increase of the bluff body angle provides better combustion efficiency and stability.     

Effect of convex platform structure on hydrogen and oxygen combustion characteristics in micro combustor

The combustion characteristics of the micro combustor with a convex platform were simulated and the effects of the height of the convex platform and the inlet velocity on the combustion process were analyzed. The results show that the setting of convex platform can significantly increase the maximum velocity and reduce the outlet velocity. When the height of the boss continues to increase, the maximum velocity is more significant, but has little effect on the outlet velocity. At the same time, the increasing height of the convex platform increases, the turbulent kinetic energy and reduces the intensity of combustion on the axis. However further increase in the height does not reduce the effect significantly. The fuel conversion rate increases significantly, but the velocity decreases. In the micro combustor with a convex platform, increasing the inlet velocity increases the axial temperature, the fuel conversion rate decreases.     

乙醇微型燃烧室燃烧特性的数值模拟研究

为了解决化石燃料储备不足与环境污染问题,生物质燃料作为石油替代能源得到大力提倡,如何合理地将化石燃料替换为生物质燃料且维持设备正常运行成为工程上亟待解决的问题。本文采用CFD软件研究了车载5 kW生物乙醇微型燃烧室的燃烧特性,对比分析了不同功率（0.5~5 kW）和出口温度（840~960 K）时的回流区长度与宽度、回流量、出口温度分布系数（OTDF）、出口NO体积分数等特征参数。结果表明：随着出口温度升高,回流区长度逐渐缩短,回流量减少,出口温度均匀性逐渐变差,出口NO体积分数明显增加;随着燃烧室功率增大,回流区长度变长,回流量增加,OTDF先增大后减小,NO体积分数随着功率的降低而显著升高,最大值出现在1 kW时,达到满负荷时的7倍。因此,为了实现稳定燃烧和减少污染物排放,该乙醇微型燃烧室应在较高的空燃比（即较低的出口温度）和功率下运行。     

Investigation on hydrogen-fueled combustion characteristics and thermal performance in a micro heat-recirculation combustor inserted with block

Numerical investigation on the premixed H₂/air combustion in a micro heat-recirculation combustor inserted with/without block is conducted. Effects of block setting, heat-recirculation, and flow rate on combustion characteristics and thermal performance are depicted and analyzed. The results demonstrate that the block enhances the flame stability and preheating effect, which also reduces the heat loss via exhaust gas, while it shortens reactants residence time. The combustor setting with a transverse block gains a better thermal performance than that inserted with a longitudinal block. With the increase of transverse block height, the high-temperature zone is broadened and radiation is improved. However, the block with a height of 10 mm separates the fluid field and weakens the effects of heat recirculation, leading to a lower outer wall temperature. Furthermore, the appropriate block insertion method and height contribute to the significant improvement of heat transfer, radiant efficiency and further optimization of micro power generator.