衬底温度和氮气分压对氮化锌薄膜的性能影响

采用射频磁控溅射法在不同衬底温度和不同氮气分压下在石英玻璃衬底上制备氮化锌薄膜. 利用XRD和喇曼散射仪分析了样品的晶体结构和组成. 结果表明当氮气分压为1/2时可以生成多晶单一相的氮化锌薄膜. 利用霍尔效应和光学透过谱测量了样品的电学和光学性质. 结果表明衬底温度对样品的电学和光学性质有很大的影响. 衬底温度从100℃上升到300℃时,样品的电阻率从0.49降低到0.023Ω·cm. 电子浓度从2.7×1016升高到8.2×1019cm-3. 在衬底温度为200℃,氮气分压为1/2时,样品的光学带隙为1.23eV.     

衬底温度对反应溅射ZnO：Al透明导电薄膜性能的影响

衬底温度在反应溅射制备ZnO：Al薄膜过程中是一个重要的工艺参数,直接决定这薄膜的性能。本文用中频脉冲磁控溅射方法,采用锌铝合金（Al的含量为2%）靶,在衬底温度170℃,工作压力2.5mTorr,氧氩比3/18的条件下,制备了ZnO：Al薄膜,利用X射线衍射仪对薄膜的结构进行了分析,利用分光光度计和四探针法测量了薄膜的光学和电学性能,研究了制备薄膜时不同的衬底温度对薄膜的结构、电学、光学性能的影响,结果表明,随着衬底温度的升高,薄膜的电阻率先下降后上升,而可见光范围平均透过率在85%以上,当衬底温度为170℃,工作压力2.5mTorr,氧氩比3/18时,薄膜电阻率最低为2.16×10-4Ωcm,方块电阻30Ω时,在可见光光范围内平均透过率高于85%。     

溅射功率对氮化锌薄膜特性的影响

在玻璃衬底上通过磁控反应溅射法,利用纯金属Zn靶,在N2-Ar等离子体氛围中制备出氮化锌薄膜。X射线衍射谱表明氮化锌具有(4 0 0)择优取向,反方铁锰矿结构。研究了溅射功率对氮化锌薄膜结构、电学及光学性质的影响。     

CeO2高K栅介质薄膜的制备工艺及其电学性质

研究了CeO2作为高K(高介电常数)栅介质薄膜的制备工艺,深入分析了衬底温度、淀积速率、氧分压等工艺条件和利用N离子轰击氮化Si衬底表面工艺对CeO2薄膜的生长及其与Si界面结构特征的影响,利用脉冲激光淀积方法在Si(100)衬底生长了具有(100)和(111)取向的CeO2外延薄膜;研究了N离子轰击氮化Si衬底表面处理工艺对Pt/CeO2/Si结构电学性质的影响.研究结果显示,利用N离子轰击氮化Si表面/界面工艺不仅影响CeO2薄膜的生长结构,还可以改善CeO2与Si界面的电学性质.     

衬底温度对ZnO:Al薄膜结构和性能的影响

利用射频磁控溅射法采用氧化锌铝(98%ZnO+2%Al2O3)为靶材在普通载玻片上制备了ZAO(ZnO:al)薄膜,研究了衬底温度对薄膜晶体结构,电学和光学性能的影响.利用X射线衍射仪、场扫描电镜对薄膜的结构及表面形貌进行了分析,利用分光光度计和电阻测试仪分别测试了薄膜的光电学性能.结果表明,衬底温度对薄膜结构及光电学性能影响最大.溅射功率120 W、衬底温度300℃、工作气压0.6 Pa制得的薄膜具有良好的光电学性能(可见光平均透过率为79.49%(考虑衬底的影响,电阻率为4.99×10-2 Ω·cm).     

CeO_2高K栅介质薄膜的制备工艺及其电学性质

研究了 Ce O2 作为高 K (高介电常数 )栅介质薄膜的制备工艺 ,深入分析了衬底温度、淀积速率、氧分压等工艺条件和利用 N离子轰击氮化 Si衬底表面工艺对 Ce O2 薄膜的生长及其与 Si界面结构特征的影响 ,利用脉冲激光淀积方法在 Si(10 0 )衬底生长了具有 (10 0 )和 (111)取向的 Ce O2 外延薄膜 ;研究了 N离子轰击氮化 Si衬底表面处理工艺对 Pt/ Ce O2 / Si结构电学性质的影响 .研究结果显示 ,利用 N离子轰击氮化 Si表面 /界面工艺不仅影响 Ce O2 薄膜的生长结构 ,还可以改善 Ce O2 与 Si界面的电学性质     

Zn0.8Na0.1Co0.1O薄膜的制备及衬底温度对其影响

采用脉冲激光沉积(PLD)技术.在温度为400、500和600℃的SiO2衬底上成功制备出Zn0.8Nao.1Co0.1O薄膜.用x射线衍射(XRD)、原子力显微镜(AFM)、荧光光谱仪、四探针电阻率测试台等对薄膜的结构、表面形貌和光电性质进行了表征,讨论了不同衬底温度对薄膜结构、光学和电学性质的影响.结果表明:掺杂没...     

电子束反应蒸发技术生长Mo掺杂In_2O_3薄膜

利用电子束反应蒸发技术,调制衬底温度200～350℃,详细研究了Mo掺杂In2O3(IMO,In2O3:Mo)薄膜的微观结构以及光电性能的变化。随着衬底温度增加,原子力显微镜(AFM)与扫描电子显微镜(SEM)图像均证明IMO薄膜表面趋于粗糙,透过率和Hall测试表明其光学和电学性能逐渐提高。在衬底温度为350℃时,获得薄膜最小电阻率为2.1×10-4Ωcm,载流子迁移率为34.2cm2/Vs,其可见光区及近红外区的平均透过率为78%。衬底温度为200℃时,薄膜表现为黑褐色,经分析X射线光电子能谱(XPS)结果认为与薄膜中钼的低价氧化有关,提高衬底温度可改善薄膜氧化状态。     

CeO2高K栅介质薄膜的制备工艺及其电学性质

研究了CeO2作为高K（高介电常数）栅介质薄膜的制备工艺,深入分析了衬底温度,淀积速率,氧化压等工艺条件和利用N离子轰击氧化Si衬底表面工艺对CeO2薄膜的生长及其与Si界面结构特征的影响,利用脉冲激光淀积方法在Si(100)衬底生成了具有（100）和（111）取向的CeO2外延薄膜,研究了N离子轰击氮化Si衬底表面处理工艺对Pt/CeO2/Si结构电学性质的影响,研究结果显示,利用N离子轰击氮化Si表面／界面工艺不仅影响CeO2薄膜的生长结构,还可以改善CeO2与Si界面的电学性质。     

应用于微电子的硅基氧化锆薄膜性质研究

用磁控溅射方法在Si(100)衬底上沉积了氧化锆薄膜.研究和比较了退火前和退火后的薄膜晶体结构、表面形貌以及Al/ZrO2/Si电容的金属-绝缘体-半导体性质.700℃氮气退火后的薄膜具有高的介电常数1 8,且在2V时漏电流小于1×10-7A/cm2,显示了良好的电学性质.氧化锆将是一种在未来的微电子器件中大有应用前景的新材料.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first     

JOURNAL OF ELECTRONICS(CHINA)

正~~     

NOTICE OF CHANGING JOURNAL OF ELECTRONICS （CHINA） TO MICROSYSTEMS ＆ NANOENGINEERING

正Journal of Electronics(China)(JE)was founded in 1984,sponsored by the Institute of Electronics,Chinese Academy of Sciences.JE is one of the first English academic journals in China in the field of Electronics and Information technology.The journal was published quarterly since it was launched in 1984 to 2003,then it is published bimonthly till now.During