Silica Monolith for the Removal of Pollutants from Gas and Aqueous Phases

This study focused on the application of mesoporous silica monoliths for the removal of organic pollutants. The physico-chemical textural and surface properties of the monoliths were investigated. The homogeneity of the textural properties along the entire length of the monoliths was assessed, as well as the reproducibility of the synthesis method. The adsorption properties of the monoliths for gaseous toluene, as a model of Volatile Organic Compounds (VOCs), were evaluated and compared to those of a reference meso-structured silica powder (MCM-41) of commercial origin. Silica monoliths adsorbed comparable amounts of toluene with respect to MCM-41, with better performances at low pressure. Finally, considering their potential application in water phase, the adsorption properties of monoliths toward Rhodamine B, selected as a model molecule of water soluble pollutants, were studied together with their stability in water. After 24 h of contact, the silica monoliths were able to adsorb up to the 70% of 1.5 × 10⁻² mM Rhodamine B in water solution.     

Efficient Lead Pb(II) Removal with Chemically Modified Nostoc commune Biomass

A new biosorbent based on Nostoc commune (NC) cyanobacteria, chemically modified with NaOH (NCM), has been prepared, characterized and tested as an effective biomass to remove Pb(II) in aqueous media. The adsorption capacity of NCM was determined to be q_e = 384.6 mg g⁻¹. It is higher than several other biosorbents reported in the literature. Structural and morphological characterization were performed by FTIR, SEM/EDX and point zero of charge pH (pH_PZC) measurements. NCM biosorbent showed more porous surfaces than those NC with heterogeneous plates including functional adsorption groups such as OH, C = O, COO⁻, COH or NH. Optimal Pb(II) adsorption occurred at pH 4.5 and 5.5 with a biomass dose of 0.5 g L⁻¹. The experimental data of the adsorption process were well fitted with the Freundlich-isotherm model and pseudo-2nd order kinetics, which indicated that Pb(II) adsorption was a chemisorption process on heterogeneous surfaces of NCM. According to the thermodynamic parameters, this process was exothermic (∆H⁰ < 0), feasible and spontaneous (∆G⁰ < 0). NCM can be regenerated and efficiently reused up to 4 times (%D > 92%). NCM was also tested to remove Pb (%R~98%) and Ca (%R~64%) from real wastewater.     

Adsorptive Removal of Hg(II) from Synthetic and Real Aqueous Solutions Using Modified Papaya Seed

The performance of chemically modified papaya seed (CMPS) adsorbent with carboxyl and amino groups has been studied. Adsorption experiments were performed with respect to the changes in initial pH of the solution, contact time, initial Hg(II) concentration, and CMPS dosage. Kinetic data were fitted to the pseudo-second-order model. The maximum adsorption capacity calculated by Langmuir model was 18.34 mg/g. CMPS was characterized by elemental analysis, Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy. The results indicate that adsorption mechanism of CMPS involves ion exchange (2Na⁺/Hg²⁺) and carboxylic-group-dominated surface complexation. Regeneration study revealed that CMPS can be used successfully for four cycles with a small adsorption capacity loss (6.8%).     

Efficient Adsorption and Recovery of Pb(II) from Aqueous Solution by a Granular pH-Sensitive Chitosan-based Semi-IPN Hydrogel

A series of granular pH-sensitive semi-interpenetrating polymer network (semi-IPN) hydrogels based on chitosan (CTS), acrylic acid (AA) and gelatine (GE) were utilized for the adsorption and recycle of Pb(II) from aqueous solutions. The composite hydrogels have been characterized by FT-IR and TGA. The effects of contact time, pH value and initial Pb(II) concentration on the adsorption were investigated. Results indicated that the adsorption capacity of the hydrogel increased with increasing pH value and initial Pb(II) concentration, and a pH-sensitive adsorption characteristic was presented. The adsorption rate of the semi-IPN hydrogels on Pb(II) is fast with an adsorption rate constant of 14.9790 mg/(g·s), and adsorption equilibrium could be reached within 10 min. The adsorption isotherms of the hydrogels for Pb(II) could be described well by the Langmuir equation, rather than the Freundlich equation. The as-prepared hydrogels showed good reusability with 0.05 mol/l HNO₃ solutions as the desorbing agent and 0.1 mol/l NaOH solutions as the regeneration agent, respectively. After five consecutive adsorption-desorption processes, the semi-IPN hydrogel with 20 wt% GE may reach 85.26% of its initial adsorption capacity. In addition, the adsorbed Pb(II) can be quantitatively recovered by simply eluting the hydrogel with dilute HNO₃ solution, and a recovery ratio of 89.27% was reached for the semi-IPN hydrogel. The satisfactory adsorption amount is mainly derived from the chelating of functional groups (i.e. –COO^? and –NH₂) with Pb(II) ions. The hydrogel adsorbents exhibited excellent affinity for Pb(II), and can be applied to treat wastewater containing heavy metal ion and simultaneously recover the valuable metal sources.     

Removal of Cd(II), Cu(II), and Pb(II) by adsorption onto natural clay: a kinetic and thermodynamic study

In this work, we study the elimination of three bivalent metal ions (Cd²⁺, Cu²⁺, and Pb²⁺) by adsorption onto natural illitic clay (AM) collected from Marrakech region in Morocco. The characterization of the adsorbent was carried out by X-ray fluorescence, Fourier transform infrared spectroscopy and X-ray diffraction. The influence of physicochemical parameters on the clay adsorption capacity for ions Cd²⁺, Cu²⁺, and Pb²⁺, namely the adsorbent dose, the contact time, the initial pH imposed on the aqueous solution, the initial concentration of the metal solution and the temperature, was studied. The adsorption process is evaluated by different kinetic models such as the pseudo-first-order, pseudo-second-order, and Elovich. The adsorption mechanism was determined by the use of adsorption isotherms such as Langmuir, Freundlich, and Temkin models. Experiments have shown that heavy metals adsorption kinetics onto clay follows the same order, the pseudo-second order. The isotherms of adsorption of metal cations by AM clay are satisfactorily described by the Langmuir model and the maximum adsorption capacities obtained from the natural clay, using the Langmuir isotherm model equation, are 5.25, 13.41, and 15.90 mg/g, respectively for Cd(II), Cu(II), and Pb(II) ions. Adsorption of heavy metals on clay is a spontaneous and endothermic process characterized by a disorder of the medium. The values of ΔH are greater than 40 kJ/mol, which means that the interactions between clay and heavy metals are chemical in nature.     

Efficient Adsorption of Chromium Ions from Aqueous Solutions by Plant-Derived Silica

Nowadays, there is great interest in the use of plant waste to obtain materials for environmental protection. In this study, silica powders were prepared with a simple and low-cost procedure from biomass materials such as horsetail and common reed, as well as wheat and rye straws. The starting biomass materials were leached in a boiling HCl solution. After washing and drying, the samples were incinerated at 700 °C for 1 h in air. The organic components of the samples were burned leaving final white powders. These powders were characterized by powder X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, dynamic light scattering (DLS), scanning electron microscopy (SEM), and low-temperature nitrogen sorption. The amorphous powders (biosilica) contained mainly SiO₂, as indicated by FTIR analysis. Horsetail-derived silica was chosen for testing the removal of dichromate ions from water solutions. This biosilica had a good ability to adsorb Cr(VI) ions, which increased after modification of the powder with the dodecylamine surfactant. It can be concluded that the applied procedure allowed obtaining high purity biosilica from plant waste with good efficiency. The produced biosilica was helpful in removing chromium ions and showed low cytotoxicity to human endothelial cells, suggesting that it can be safely used in environmental remediation.     

Stoeber二氧化硅溶胶中氨水的去除方法

通过pH值、电导率和二氧化硅解离量的测定，研究了Stfber二氧化硅溶胶的提纯过程．发现离心水洗很难完全去除体系中的氨水并且残留的氨水会影响二氧化硅粒子的化学稳定性．对二氧化硅溶胶进行酸处理后再提纯，可以大大加速提纯过程并消除氨水对二氧化硅粒子化学稳定性的影响。     

Removal of Cu(II) and Pb(II) from Aqueous Solutions Using Nanoporous Materials

Russian Journal of Physical Chemistry A - The present work deals with the adsorption of Cu2+ and Pb2+ on zeolites (ZSM-5, mordenite) and mesoporous materials (MCM-48, MCM-41). The characterization...     

Metal Sorption,Solid Phase Extraction and Preconcentration Properties of Two Silica Gel Phases Chemically Modified with 2-Hydroxy-1-Naphthaldehyde

Active silica gel phase (I) was chemically modified to the corresponding amino- (SiNH₂) and chloro- (SiCl) derivatives via silylation reactions. These were used to synthesize two newly modified silica gel phases (II, III) by direct chemical reaction with 2-hydroxynaphthaldehyde (2-HNA). The surface coverage values are 370, 432µmolg^–1 and 320, 355µmolg^–1 for (II) and (III), on the basis of thermal desorption and metal probe testing method, respectively. The metal sorption properties of silica gel phases (II, III) were studied and compared with active silica gel phase (I). The maximum determined metal capacity values were found to be 10–110, 20–290 and 20–370µmolg^–1 for phases I, II and III, respectively. The distribution coefficient values (K_d) were also determined for a series of metal ions, and the results showed that the two new chemically modified phases (II and III) were highly selective for Cu²⁺, Zn²⁺, Cd²⁺, Hg²⁺ and Pb²⁺. The potential applications of silica gel phases (II, III) as solid phase extractors for the same five metal ions spiked in drinking tap water (1.000µgmL^–1) were found to give percentage recovery values in the range of 90.2–96.3±4.1–6.3%, while pre-concentration of the same five metal ions spiked in drinking tap water (50.0ngmL^–1) was successfully accomplished with a percentage recovery range of 92.6–95.8±4.8–5.7%.Received December 16, 2002; accepted May 14, 2003 published online September 1, 2003     

Stber二氧化硅溶胶中氨水的去除方法

通过pH值、电导率和二氧化硅解离量的测定,研究了St ber二氧化硅溶胶的提纯过程.发现离心水洗很难完全去除体系中的氨水并且残留的氨水会影响二氧化硅粒子的化学稳定性.对二氧化硅溶胶进行酸处理后再提纯,可以大大加速提纯过程并消除氨水对二氧化硅粒子化学稳定性的影响.     

Enhancing Removal of Cr(VI), Pb2+, and Cu2+ from Aqueous Solutions Using Amino-Functionalized Cellulose Nanocrystal

In this work, the amino-functionalized cellulose nanocrystal (ACNC) was prepared using a green route and applied as a biosorbent for adsorption of Cr(VI), Pb²⁺, and Cu²⁺ from aqueous solutions. CNC was firstly oxidized by sodium periodate to yield the dialdehyde nanocellulose (DACNC). Then, DACNC reacted with diethylenetriamine (DETA) to obtain amino-functionalized nanocellulose (ACNC) through a Schiff base reaction. The properties of DACNC and ACNC were characterized by using elemental analysis, Fourier transform infrared spectroscopy (FT-IR), Kaiser test, atomic force microscopy (AFM), X-ray diffraction (XRD), and zeta potential measurement. The presence of free amino groups was evidenced by the FT-IR results and Kaiser test. ACNCs exhibited an amphoteric nature with isoelectric points between pH 8 and 9. After the chemical modification, the cellulose I polymorph of nanocellulose remained, while the crystallinity decreased. The adsorption behavior of ACNC was investigated for the removal of Cr(VI), Pb²⁺, and Cu²⁺ in aqueous solutions. The maximum adsorption capacities were obtained at pH 2 for Cr(VI) and pH 6 for Cu²⁺ and Pb²⁺, respectively. The adsorption all followed pseudo second-order kinetics and Sips adsorption isotherms. The estimated adsorption capacities for Cr(VI), Pb²⁺, and Cu²⁺ were 70.503, 54.115, and 49.600 mg/g, respectively.     

Characterization of Magnetic Nanoiron Oxides for the Removal of Metal Ions from Aqueous Solution

ABSTRACT

Two nanostructured hybrid materials are reported that include uncoated magnetic nanoiron oxides and magnetic nanoiron oxides treated with rose leaf extract. Atomic and molecular absorption spectrometry were used to evaluate the sensitivity of these materials for the isolation of Cr(VI), Zn(II), Pb(II), and Ca(II) from aqueous solution. The structure and physicochemical properties of the resulting nanohybrids were characterized by scanning electron microscopy coupled with energy-dispersive spectroscopy, atomic force microscopy, and X-ray diffraction. The results show that following 15?min of contact in acidic solution, the uncoated magnetic nanoiron oxides removed approximately 90% of Cr(VI), while the magnetic nanoiron oxides coated with rose leaf extract removed 92% of the analyte. These correspond to most industrial wastewater conditions. For the removal of Ca(II) and Zn(II), it was necessary to adjust the pH to neutral to maximize the efficiency. Pb(II) showed maximum removal efficiency when the solution is basic. The simple rose extract suspension was also used for metal removal with high capacity. The results demonstrate that the magnetic nanoiron oxides were uniformly distributed in the rose leaf extract. The extract served as a capping agent due to the presence of polyphenolics.     

Sorption Removal of Pb（Ⅱ） from Solution by Uncalcined and Calcined MgAl-Layered Double Hydroxides

Layered double hydroxide （LDH） with a Mg/Al molar ratio of 1 ： 1 was synthesized by using a co-precipitation method and its calcined product （CLDH） was obtained by calcination of the MgAl-LDH at 500 ℃. The sorption removal of Pb^2＋ from solution was investigated, finding that both LDH and CLDH show good sorption ability and they could be used as a new type of environmental sorbent for the removal of Pb^2＋ from water. The sorption kinetics and the sorption isotherms of Pb^2＋ on both LDH and CLDH can be described by the pseudo-second order kinetics and Freundlich isotherm, respectively, under the studied conditions. The sorption amounts of Pb^2＋ on LDH and CLDH are independent of pH in a pH range of about 3-10. The presence of NaNO3 may inhibit the sorption of Pb^2＋ on LDH while hardly affect that on CLDH. The sorption mechanism of Pb^2＋ on LDH and CLDH may be attributed to the surface precipitation and the surface complex adsorption. The surface complex adsorption may be further distinguished to the chemical binding adsorption forming the inner-sphere surface complexes and the electrostatic binding adsorption forming the outer-sphere surface complexes. The sorption mechanism of Pb^2＋ on LDH may be attributed to the surface precipitation and the electrostatic binding adsorption, while that on CLDH may be attributed to the surface precipitation and the chemical binding adsorption.     

Molecular Recognition and Scavenging of Arsenate from Aqueous Solution Using Dimetallic Receptors

A series of copper(II), nickel(II) and zinc(II) dimetallic complexes were prepared and their affinities towards arsenate investigated. Indicator displacement assays (IDAs) were carried out to establish the complexes with best affinities towards arsenate. A di‐zinc complex ( 3 ) was selected and its arsenate‐binding abilities investigated by isothermal titration calorimetry (ITC). The X‐ray crystal structure of this metallo‐receptor bound to arsenate is also reported, which allowed us to establish the binding mode between 3 and this oxyanion. Immobilising 3 onto HypoGel resin yielded a novel adsorbent (Zn–HypoGel) with high affinity for arsenate. Adsorption of arsenate from competitive solutions and natural groundwater was greater than that of the commercially used iron oxide Bayoxide E33. Zn–HypoGel could be efficiently and simply regenerated by washing with sodium acetate solution.     

Fabrication of New Cellulose-Based Sorbents for Fast and Efficient Removal of Hazardous Al(III) Ions from Their Aqueous Solutions

Cellulose was used as a base polymer in two prepared resins when it was grafted by glycidyl methacrylate (GMA) then immobilized with 8-hydroxyquinoline by two different procedures. The resulting resins were characterized by infrared (IR) spectroscopy, thermogravimetric analysis (TGA), and nitrogen surface area measurements (BET). The two resins were used in the removal of hazardous Al(III) from their aqueous solutions. The present work discussed the preparation and the effect of spacer arms length used in the functionalization steps on the adsorption process. The resin with longer spacer arm showed faster kinetics compared with the other one toward Al(III) ion adsorption. Fast and efficient adsorption of hazardous Al(III) ions from drinking water by these resins indicates their applicability in water treatment applied field. Thermodynamic parameters were calculated for the studied resins and showed that they possess spontaneous exothermic nature. The regeneration efficiencies reached 90 ± 0.5% over three cycles using a mixture of 2 M HCl and 0.5 M HNO₃.     

Selective Solid Phase Extraction and Pre-Concentration of Heavy Metals from Seawater by Physically and Chemically Immobilized 4-Amino-3-Hydroxy-2-(2-Chlorobenzene)-Azo-1-Naphthalene Sulfonic Acid Silica Gel

4-Amino-3-hydroxy-2-(2-chlorobenzene)-azo-1-naphthalene sulfonic acid (AHCANSA) was used as a chelating modifier to improve the reactivity of the silica gel surface in terms of selective binding and extraction of heavy metal ions. The surface coverage values were found to be 0.488 and 0.473mmolg^–1 for the newly modified physically adsorbed silica gel phase (I) and chemically immobilized-AHCANSA phase (II), respectively. The modified silica gel phases (I, II) were tested for stability in different acidic buffer solutions (pH 1–6) and found to be highly resistant to hydrolysis and leaching by buffer solutions above pH 2. The application of these two phases as solid extractors for a series of mono-, di-, and tri-valent metal ions from aqueous solutions was also performed with different controlling factors such as the pH value of metal ion solutions and equilibrium shaking time. The mmolg^–1 metal capacity values determined by silica gel phases (I, II) were found to confirm high affinity and selectivity characters for binding with heavy metal ions such as Cr³⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺ and Pb²⁺ in a range of 0.250–0.483. The tested alkali and alkaline earth metals, Na⁺, K⁺, Mg²⁺ and Ca²⁺, were found to exhibit little interaction and binding ability with the modified silica gel phases. The selectivity characters incorporated into the modified silica gel phases were further utilized and applied in solid phase extraction and pre-concentration of trace concentration levels (1.0µgmL^–1 and 2.00–2.50ngmL^–1) from real seawater samples. The percentage recovery values determined for Cr³⁺, Cu²⁺, Zn²⁺, Cd²⁺ and Pb²⁺ were found to be in the range of 95.2–98.1±2.0–5.0%, and the pre-concentration recovery values for the same tested heavy metal ions were found to be in the range of 92.5–97.1±3.0–6.0% for the two newly modified silica gel phases with a pre-concentration factor of 500.Received December 20, 2002; accepted May 14, 2003 published online September 1, 2003     

Synthesis and Application of Hydride Silica Composites for Rapid and Facile Removal of Aqueous Mercury

The adsorption of ionic mercury(II) from aqueous solution on functionalized hydride silicon materials was investigated. The adsorbents were prepared by modification of mesoporous silica C‐120 with triethoxysilane or by converting alkoxysilane into siloxanes by reaction with acetic acid. Mercury adsorption isotherms at 20 °C are reported, and maximum mercury loadings were determined by Langmuir fitting. Adsorbents exhibited efficient and rapid removal of ionic mercury from aqueous solution, with a maximum mercury loading of approximately 0.22 and 0.43 mmol of Hg g^?1 of silica C‐120 and polyhedral oligomeric silsesquioxane (POSS) xerogel, respectively. Adsorption efficiency remained almost constant from pH 2.7 to 7. These inexpensive adsorbents exhibiting rapid assembly, low pH sensitivity, and high reactivity and capacity, are potential candidates as effective materials for mercury decontamination in natural waters and industrial effluents.     

Adsorption and Equilibrium Isotherm Study of Removal of Copper (II) Ions from Aqueous Solution by Chemically Modified Abelmoschus esculentus Fibers

The present study explores surface modification of Abelmoschus esculentus by graft copolymerization reaction using acrylonitrile as a monomer and ascorbic acid/H₂O₂ as a redox initiator. Further, polyacrylonitrile grafted fibers were treated with hydroxylamine to convert the nitrile group of the grafted fiber into the amidoxime group to enhance adsorption of copper ions from wastewater. The graft copolymers and amidoximated fibers were characterized by FT-IR and FE-SEM. The effects of physicochemical parameters such as pH of the solution, initial metal ion concentration, and time on Cu(II) adsorption were studied to optimize condition for maximum adsorption. In addition, Langmuir, Freundlich, and Tempkin models were applied to describe the adsorption isotherm of Cu²⁺ ions.