Preparation of Li2S-GeSe2-P2S5 electrolytes by a single step ball milling for all-solid-state lithium secondary batteries

Glass-ceramic and glass Li₂S-GeSe₂-P₂S₅ electrolytes were prepared by a single step ball milling (SSBM) process. Various compositions of Li_4−xGe_1−xP_xS_2(1+x)Se_2(1−x) with/without heat treatment (HT) from x = 0.55 to x = 1.00 were systematically investigated. Structural analysis by X-ray diffraction (XRD) showed gradual increase of the lattice constant followed by significant phase change with increasing GeSe₂. HT also affected the crystallinity. Incorporation of GeSe₂ in Li₂S-P₂S₅ kept high conductivity with a maximum value of 1.4 × 10⁻³ S cm⁻¹ at room temperature for x = 0.95 in Li_4−xGe_1−xP_xS_2(1+x)Se_2(1−x) without HT. All-solid-state LiCoO₂/Li cells using Li₂S-GeSe₂-P₂S₅ as solid-state electrolytes (SE) were tested by constant-current constant-voltage (CCCV) charge-discharge cycling at a current density of 50 μA cm⁻² between 2.5 and 4.3 V (vs. Li/Li⁺). In spite of the extremely high conductivity of the SE, LiCoO₂/Li cells showed a large irreversible reaction especially during the first charging cycle. LiCoO₂ with SEs heat-treated at elevated temperature exhibited a capacity over 100 mAh g⁻¹ at the second cycle and consistently improved cycle retention, which is believed to be due to the better interfacial stability.     

High-rate performance of all-solid-state lithium secondary batteries using Li4Ti5O12 electrode

The all-solid-state Li–In/Li₄Ti₅O₁₂ cell using the 80Li₂S·20P₂S₅ (mol%) solid electrolyte was assembled to investigate rate performances. It was difficult to obtain the stable performance at the charge current density of 3.8 mA cm⁻² in the all-solid-state cell. In order to improve the rate performance, the pulverized Li₄Ti₅O₁₂ particles were applied to the all-solid-state cell, which retained the reversible capacity of about 90 mAh g⁻¹ at 3.8 mA cm⁻². The 70Li₂S·27P₂S₅·3P₂O₅ glass–ceramic, which exhibits the higher lithium ion conductivity than the 80Li₂S·20P₂S₅ solid electrolyte, was also used. The Li–In/70Li₂S·27P₂S₅·3P₂O₅ glass–ceramic/pulverized Li₄Ti₅O₁₂ cell was charged at a current density higher than 3.8 mA cm⁻² and showed the reversible capacity of about 30 mAh g⁻¹ even at 10 mA cm⁻² at room temperature.     

Fabrication of all-solid-state lithium battery with lithium metal anode using Al2O3-added Li7La3Zr2O12 solid electrolyte

Li₇La₃Zr₂O₁₂ (LLZ) solid electrolyte is one of the promising electrolytes for all-solid-state battery due to its high Li ion conductivity and stability against Li metal anode. However, high calcination temperature for LLZ preparation promotes formation of La₂Zr₂O₇ impurity phase. In this paper, an effect of Al₂O₃ addition as sintering additive on LLZ solid electrolyte preparation and electrochemical properties of Al₂O₃-added LLZ were examined. By the Al₂O₃ addition, sintered LLZ pellet could be obtained after 1000 °C calcination, which is 230 °C lower than that without Al₂O₃ addition. Chemical and electrochemical properties of the Al₂O₃-added LLZ, such as stability against Li metal and ion conductivity, were comparable with the LLZ without Al₂O₃ addition, i.e. σ_bulk and σ_total were 2.4 × 10⁻⁴ and 1.4 × 10⁻⁴ S cm⁻¹ at 30 °C, respectively. All-solid-state battery with Li/Al₂O₃-added LLZ/LiCoO₂ configuration was fabricated and its electrochemical properties were tested. In cyclic voltammogram, clear redox peaks were observed, indicating that the all-solid-state battery with Li metal anode was successfully operated. The redox peaks were still observed even after one year storage of the all-solid-state battery in the Ar-filled globe-box. It can be inferred that the Al₂O₃-added LLZ electrolyte would be a promising candidate for all-solid-state battery because of facile preparation by the Al₂O₃ addition, relatively high Li ion conductivity, and good stability against Li metal and LiCoO₂ cathode.     

Electrochemical performance of all-solid-state lithium secondary batteries improved by the coating of Li2O-TiO2 films on LiCoO2 electrode

All-solid-state lithium secondary batteries using LiCoO₂ particles coated with amorphous Li₂O-TiO₂ films as an active material and Li₂S-P₂S₅ glass-ceramics as a solid electrolyte were fabricated; the electrochemical performance of the batteries was investigated. The interfacial resistance between LiCoO₂ and solid electrolyte was decreased by the coating of Li₂O-TiO₂ films on LiCoO₂ particles. The rate capability of the batteries using the LiCoO₂ coated with Li₂Ti₂O₅ (Li₂O·2TiO₂) film was improved because of the decrease of the interfacial resistance of the batteries. The cycle performance of the all-solid-state batteries under a high cutoff voltage of 4.6 V vs. Li was highly improved by using LiCoO₂ coated with Li₂Ti₂O₅ film. The oxide coatings are effective in suppressing the resistance increase between LiCoO₂ and the solid electrolyte during cycling. The battery with the LiCoO₂ coated with Li₂Ti₂O₅ film showed a large initial discharge capacity of 130 mAh/g and good capacity retention without resistance increase after 50 cycles at the current density of 0.13 mA/cm².     

Effect of capacity matchup in the LiNi0.5Mn1.5O4/Li4Ti5O12 cells

The effect of the capacity matchup between cathode and anode in the LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ cell system on cycling property, choice of electrolyte, high voltage and overcharge tolerances was investigated by comparing the cells with Li₄Ti₅O₁₂ limiting capacity with the cells with LiNi_0.5Mn_1.5O₄ limiting capacity. The former exhibits better cycling performance and less limitation of electrolyte choice than the latter. Furthermore, the Li₄Ti₅O₁₂-limited cell exhibits better tolerance to high voltage and overcharge than the LiNi_0.5Mn_1.5O₄-limited cell, owing to taking advantage of the extra capacity of Li₄Ti₅O₁₂ below 1 V. It is thus recommended that the LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ cell whose capacity is limited by Li₄Ti₅O₁₂ anode should be used to extend the application of the state-of-the-art lithium-ion batteries.     

All-solid-state lithium secondary batteries using LiCoO2 particles with pulsed laser deposition coatings of Li2S-P2S5 solid electrolytes

Electrode-electrolyte composite materials were prepared by coating a highly conductive Li₂S-P₂S₅ solid electrolyte onto LiCoO₂ electrode particles using pulsed laser deposition (PLD). Cross-sections of the composite electrode layers of the all-solid-state cells were observed using a transmission electron microscope to investigate the packing morphology of the LiCoO₂ particles and the distribution of solid electrolyte in the composite electrode. All-solid-state cells based on a composite electrode composed entirely of solid-electrolyte-coated LiCoO₂ were fabricated, and their performance was investigated. The coating amounts of Li₂S-P₂S₅ solid electrolytes on LiCoO₂ particles and the conductivity of the coating material were controlled to increase the capacity of the resulting all-solid-state cells. All-solid-state cells using LiCoO₂ with thick solid electrolyte coatings, grown over 120 min, had a capacity of 65 mAh g⁻¹, without any addition of Li₂S-P₂S₅ solid electrolyte particles to the composite electrode. The capacity of the all-solid-state cell increased further after increasing the conductivity of the Li₂S-P₂S₅ solid electrolyte coating by heat treatment at 200 °C. Furthermore, an all-solid-state cell based on a composite electrode using both a solid electrolyte coating and added solid electrolyte particles was fabricated, and the capacity of the resulting all-solid-state cell increased to 95 mAh g⁻¹.     

State of charge (SOC) dependence of lithium carbonate on LiNi0.8Co0.15Al0.05O2 electrode for lithium-ion batteries

Lithium-ion batteries using LiNi_0.8Co_0.15Al_0.05O₂ (NCA) as the positive electrode material and hard carbon as the negative electrode material with electrolyte of mixture of ethylene carbonate and dimethyl carbonate containing LiPF₆ were fabricated, and the surface materials on the positive electrode were observed by ATR spectroscopy of FT-IR measurement. Lithium carbonate was mainly observed as the surface material and the intensity of IR absorption peaks were depended on state of charge (SOC) of the batteries. The result suggests that the amount of lithium carbonate increases by discharge and decreases by charge.     

Li4Ti5O12/Sn composite anodes for lithium-ion batteries: Synthesis and electrochemical performance

Li₄Ti₅O₁₂/tin phase composites are successfully prepared by cellulose-assisted combustion synthesis of Li₄Ti₅O₁₂ matrix and precipitation of the tin phase. The effect of firing temperature on the particulate morphologies, particle size, specific surface area and electrochemical performance of Li₄Ti₅O₁₂/tin oxide composites is systematically investigated by SEM, XRD, TG, BET and charge-discharge characterizations. The grain growth of tin phase is suppressed by forming composite with Li₄Ti₅O₁₂ at a calcination of 500 °C, due to the steric effect of Li₄Ti₅O₁₂ and chemical interaction between Li₄Ti₅O₁₂ and tin oxide. The experimental results indicate that Li₄Ti₅O₁₂/tin phase composite fired at 500 °C has the best electrochemical performance. A capacity of 224 mAh g⁻¹ is maintained after 50 cycles at 100 mA g⁻¹ current density, which is still higher than 195 mAh g⁻¹ for the pure Li₄Ti₅O₁₂ after the same charge/discharge cycles. It suggests Li₄Ti₅O₁₂/tin phase composite may be a potential anode of lithium-ion batteries through optimizing the synthesis process.     

Preparation of spherical LiNi0.80Co0.15Mn0.05O2 lithium-ion cathode material by continuous co-precipitation

Micro-spherical Ni_0.80Co_0.15Mn_0.05(OH)₂ precursors with a narrow size-distribution and high tap-density are prepared successfully by continuous co-precipitation of the corresponding metal salt solutions using NaOH and NH₄OH as precipitation and complexing agents. LiNi_0.80Co_0.15Mn_0.05O₂ is then prepared as a lithium battery cathode from this precursor by the introduction of LiOH·H₂O. The pH and NH₃:metal molar ratio show significant effects on the morphology, microstructure and tap-density of the prepared Ni_0.80Co_0.15Mn_0.05(OH)₂ and the R values and I(0 0 3)/I(1 0 4) ratio of lithiated LiNi_0.80Co_0.15Mn_0.05O₂. Spherical LiNi_0.80Co_0.15Mn_0.05O₂ prepared under optimum conditions reveals a hexagonally ordered, layered structure without cation mixing and an initial charging capacity of 176 mAhg⁻¹. More than 91% of the capacity is retained after 40 cycles at the 1 C rate in a cut-off voltage range of 4.3-3.0 V.     

Electrochemical behaviors of wax-coated Li powder/Li4Ti5O12 cells

The wax-coated Li powder specimen was effectively synthesized using the drop emulsion technique (DET). The wax layer on the powder was verified by SEM, Focused Ion Beam (FIB), EDX and XPS. The porosity of a sintered wax-coated Li electrode was measured by linear sweep voltammetry (LSV) and compared with that of a bare, i.e., un-coated Li electrode. The electrochemical behavior of the wax-coated Li powder anode cell was examined by the impedance analysis and cyclic testing methods. The cyclic behavior of the wax-coated Li powder anode with the Li₄Ti₅O₁₂ (LTO) cathode cell was examined at a constant current density of 0.35 mA cm⁻² with the cut-off voltages of 1.2–2.0 V at 25 °C. Over 90% of the initial capacity of the cell remained even after the 300th cycle. The wax-coated Li powder was confirmed to be a stable anode material.     

Electrochemical performance of all-solid-state Li batteries based LiMn0.5Ni0.5O2 cathode and NASICON-type electrolyte

LiNi_0.5Mn_0.5O₂ thin films have been deposited on the NASICON-type glass ceramics, Li_1+x+yAl_xTi_2−xSi_yP_3−yO₁₂ (LATSP), by radio frequency (RF) magnetron sputtering followed by annealing. The films have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Raman spectroscopy. All-solid-state Li/PEO₁₈-Li(CF₃SO₂)₂N/LATSP/LiNi_0.5Mn_0.5O₂/Au cells are fabricated using the LiNi_0.5Mn_0.5O₂ thin films and the LATSP electrolyte. The electrochemical performance of the cells is investigated by galvanostatic cycling, cyclic voltammetry (CV), potentiostatic intermittent titration technique (PITT) and electrochemical impedance spectroscopy (EIS). Interfacial reactions between LiNi_0.5Mn_0.5O₂ and LATSP occur at a temperature as low as 300 °C with the formation of Mn₃O₄, resulting in an increased obstacle for Li-ion diffusion across the LiNi_0.5Mn_0.5O₂/LATSP interface. The electrochemical performance of the cells is limited by the interfacial resistance between LATSP and LiNi_0.5Mn_0.5O₂ as well as the Li-ion diffusion kinetics in LiNi_0.5Mn_0.5O₂ bulk.     

Ni3(PO4)2-coated Li[Ni0.8Co0.15Al0.05]O2 lithium battery electrode with improved cycling performance at 55 °C

To improve the cycling performance of LiNi_0.8Co_0.15Al_0.05O₂ at 55 °C, a thin Ni₃(PO₄) layer was homogeneously coated onto the cathode particle via simple ball milling. The morphology of the Ni₃(PO₄)₂-coated LiNi_0.8Co_0.15Al_0.05O₂ particle was characterized using SEM and TEM analysis, and the coating thickness was found to be approximately 10-20 nm. The Ni₃(PO₄)₂-coated LiNi_0.8Co_0.15Al_0.05O₂ cell showed improved lithium intercalation stability and rate capability especially at high C rates. This improved cycling performance was ascribed to the presence of Ni₃(PO₄)₂ on the LiNi_0.8Co_0.15Al_0.05O₂ particle, which protected the cathode from chemical attack by HF and thus suppressed an increase in charge transfer resistance. Transmission electron microscopy of extensively cycled particles confirmed that the particle surface of the Ni₃(PO₄)₂-coated LiNi_0.8Co_0.15Al_0.05O₂ remained almost undamaged, whereas pristine particles were severely serrated. The stabilization of the host structure by Ni₃(PO₄)₂ coating was also verified using X-ray diffraction.     

High-strength all-solid lithium ion electrodes based on Li4Ti5O12

A Li₄Ti₅O₁₂-Li_0.29La_0.57TiO₃-Ag electrode composite was fabricated via sintering the corresponding powder mixture. The process achieved a final relative density of 97% the theoretical. Relatively thick, ∼100 μm, electrodes were fabricated to enhance the energy density relatively to the traditional solid-state thin film battery electrodes. The sintered electrode composite delivered full capacity in the first discharge at C/40 discharge rate. Full capacity utilization resulted from the 3D percolated network of both solid electrolyte and metal, which provide paths for ionic and electronic transport, respectively. The electrodes retained 85% of the theoretical capacity after 10 cycles at C/40 discharge rate. The tensile strength and the Young's modulus of the sintered electrode composite are the highest reported values to date, and are at least an order of magnitude higher than the corresponding value of traditional tapecast “composite electrodes”. The results demonstrate the concept of utilizing thick all-solid electrodes for high-strength batteries, which might be used as multifunctional structural and energy storage materials.     

Investigation of layered Ni0.8Co0.15Al0.05LiO2 in electrode for low-temperature solid oxide fuel cells

A symmetrical cell composed of Ce_0.9Gd_0.1O_2?δ electrolyte is constructed with 0.5 mm thickness and Ni_0.8Co_0.15Al_0.05LiO₂ (NCAL)-foam Ni composite electrodes. Electrochemical performance of the cell and electrochemical impedance spectra (EIS) are measured using the three-electrode method. The maximum power densities of the cell are 93.6 and 159.7 mW cm^?2 at 500 and 550 °C, respectively. The polarization resistances of the cathode are 0.393 and 0.729 Ω cm^?2 at 550 and 500 °C, indicating that NCAL has good ORR activity. HT-XRD results for NCAL do not show phase transitions or any additional new phases at elevated temperatures, indicating that NCAL has a stable phase structure. The surface characteristics of the NCAL powders are studied by XPS and FTIR. The results reveal that Li₂CO₃ and the cation-disordered “NiO-like” phase are formed on the surface of the layered NCAL structure due to prolonged exposure to air and contain a large number of oxygen vacancies. The cation-disordered “NiO-like” phase and Li₂CO₃ composite in the melt and partial melt states in the high temperature region are considered to possess very high ionic conductivity and lower activation energy for oxygen reduction reactions.     

Nanosized Li4Ti5O12/graphene hybrid materials with low polarization for high rate lithium ion batteries

We report a simple strategy to prepare a hybrid of lithium titanate (Li₄Ti₅O₁₂, LTO) nanoparticles well-dispersed on electrical conductive graphene nanosheets as an anode material for high rate lithium ion batteries. Lithium ion transport is facilitated by making pure phase Li₄Ti₅O₁₂ particles in a nanosize to shorten the ion transport path. Electron transport is improved by forming a conductive graphene network throughout the insulating Li₄Ti₅O₁₂ nanoparticles. The charge transfer resistance at the particle/electrolyte interface is reduced from 53.9 Ω to 36.2 Ω and the peak currents measured by a cyclic voltammogram are increased at each scan rate. The difference between charge and discharge plateau potentials becomes much smaller at all discharge rates because of lowered polarization. With 5 wt.% graphene, the hybrid materials deliver a specific capacity of 122 mAh g⁻¹ even at a very high charge/discharge rate of 30 C and exhibit an excellent cycling performance, with the first discharge capacity of 132.2 mAh g⁻¹ and less than 6% discharge capacity loss over 300 cycles at 20 C. The outstanding electrochemical performance and acceptable initial columbic efficiency of the nano-Li₄Ti₅O₁₂/graphene hybrid with 5 wt.% graphene make it a promising anode material for high rate lithium ion batteries.     

Lithium diffusion in Li4Ti5O12 at high temperatures

Synthesis of the spinel lithium titanate Li₄Ti₅O₁₂ by an alkoxide-free sol-gel method is described. This method yields highly pure and crystalline Li₄Ti₅O₁₂ samples at relatively low temperature (850 °C) and via short thermal treatment (2 h). ⁶Li magic angle spinning nuclear magnetic resonance (MAS NMR) measurements on these samples were carried out at high magnetic field (21.1 T) and over a wide temperature range (295-680 K). The temperature dependence of the chemical shifts and integral intensities of the three ⁶Li resonances demonstrates the migration of lithium ions from the tetrahedral 8a to the octahedral 16c sites and the progressive phase transition from a spinel to a defective NaCl-type structure. This defective structure has an increased number of vacancies at the 8a site, which facilitate lithium diffusion through 16c → 8a → 16c pathways, hence providing an explanation for the reported increase in conductivity at high temperatures. Molecular dynamics simulations of the spinel oxides Li_4+xTi₅O₁₂, with 0 ≤ x ≤ 3, were also performed with a potential shell model in the temperature range 300-700 K. The simulations support the conclusions drawn from the NMR measurements and show a significant timescale separation between lithium diffusion through 8a and 16c sites and that out of the 16d sites.     

Formation of the high lithium ion conducting phase from mechanically milled amorphous Li2S-P2S5 system

The fast ionic conducting structure similar to thio-Lithium Super Ionic Conductor (LISICON) phase is synthesized in the Li₂S-P₂S₅ system. The Li₂S-P₂S₅ glass-ceramics with the composition of xLi₂S·(100−x)P₂S₅ (75 ≤ x ≤ 80) are prepared by the heat-treatment of mechanically milled amorphous sulfide powders. In the binary Li₂S-P₂S₅ system, 78.3Li₂S·21.7P₂S₅ glass ceramic prepared by mechanical milling and subsequent heat-treatment at 260 °C for 3 h shows the highest conductivity of 6.3 × 10⁻⁴ S cm⁻¹ at room temperature and the lowest activation energy for conduction of 30.5 kJ mol⁻¹. The enhancement of conductivity with increasing x up to 78.3 is probably caused by the introduction of interstitial lithium ions at the Li sites which affects the Li ion distribution. The prepared electrolyte exhibits the lithium ion transport number of almost unity and voltage stability of 5 V vs. Li at room temperature.     

Synthesis and electrochemical properties of LiNi0.8Co0.2O2 nanopowders for lithium ion battery applications

Nitrates of lithium, cobalt and nickel are utilized to synthesize LiNi_0.8Co_0.2O₂ cathode material through sol-gel technique. Various synthesis parameters such as calcination time and temperature as well as chelating agent are studied to determine the optimized condition for material processing. Using TG/DTA techniques, the optimized calcination temperatures are selected. Different characterization techniques such as ICP, XRD and TEM are employed to characterize the chemical composition, crystal structure, size and morphology of the powders. Micron and nano-sized powders are produced using citric/oxalic and TEA as chelating agent, respectively. Selected powders are used as cathode material to assemble batteries. Charge-discharge testing of these batteries show that the highest discharge capacity is 173 mAh g⁻¹ at a constant current of 0.1 mA cm⁻², between 3.0 and 4.2 V. This is obtained in a battery assembled with the nanopowder produced by TEA as chelating agent.     

Micron-sized, carbon-coated Li4Ti5O12 as high power anode material for advanced lithium batteries

Spherical, high tap density, carbon-coated Li₄Ti₅O₁₂ powders are synthesized by a spray-drying process followed by a facile pitch coating. XRD, SEM, TEM analyses show that the carbon layer uniformly coats the Li₄Ti₅O₁₂ particles without producing any crystalline changes. We demonstrate that the carbon coating significantly increases the electrical conductivity of Li₄Ti₅O₁₂ making it an efficient, high rate electrode for lithium cells. The electrochemical tests in fact confirm that the 3.25 wt% carbon-coated Li₄Ti₅O₁₂ electrode operates with ultra high rate capacity levels, i.e., 100 C and has excellent capacity retention and charge-discharge efficiency for a life extending over 100 cycles.     

Electrochemical properties of Li1.4Al0.4Ti1.6(PO4)3 synthesized by a co-precipitation method

Sub-micron Li_1.4Al_0.4Ti_1.6(PO₄)₃ (LATP) ceramic powder is synthesized by a co-precipitation method which can be applied for mass production. A pure Nasicon phase is confirmed by X-ray diffraction analysis and the primary particle size of the product is 200-500 nm. The sinterability of LATP is investigated and the relative density of 97% reached at a sintering temperature as low as 900 °C for 6 h. The bulk lithium ionic conductivity of the sintered pellet is 2.19 × 10⁻³ S cm⁻¹, and a total conductivity of 1.83 × 10⁻⁴ S cm⁻¹ is obtained.