Investigation of Long Period Grating as refractive index sensor

In this paper, we have theoretically and experimentally investigated the response of Long Period Grating (LPG) as refractive index sensor. The response has been checked for the refractive index ranging from 1 to 1.458. It was found that the experimental results are very close to the theoretically simulated results. The ambient refractive index response of an LPG over a much wider index range has been modeled for values both less and more than the cladding refractive index.     

Measurement of the magnetic field-dependent refractive index of magnetic fluids in bulk

An optical alignment-free and highly accurate method is employed to measure the magnetic field-dependent refractive index of magnetic fluid(MF) in bulk.The measured refractive index decreases significantly with the increasing magnetic strength and then tends to saturate in the high intensity range.By applying a tunable magnetic field ranging between 0 and 1661 Oe,the maximum shift of the refractive index of MF in bulk iS found to be 0.0231.     

基于飞秒光梳多路同步锁相的多波长干涉实时绝对测距及其非模糊度量程分析

飞秒光梳被广泛用于时间频率技术和精密光谱测量,由其时频特性所衍生的绝对测距技术以可溯源、大尺寸、高精度等优点有望成为未来长度计量的最重要手段.本文提出了一种基于飞秒光梳多路同步锁相的多波长干涉实时绝对测距方法,使多个连续波激光器通过光学锁相环技术同步锁定到飞秒光梳梳模上,通过多路同步相位测量和小数重合算法最终实现绝对距离测量.所提测量方法不仅能保留传统激光干涉测距的高分辨力和精度,而且可溯源至时间频率基准,对高精度长度测量、尤其是对物理复现“米”的定义具有重要计量意义.测距实验证明,四波长干涉测距的非模糊度量程达到44.6 mm,折射率波动导致非模糊度量程变化为纳米量级;多波长干涉测距的非模糊度量程也受制于空气折射率的测量误差,多波长干涉绝对测距的非模糊度量程在实验室环境下可达数米、甚至几十米,并通过2米线性位移实验证明了多波长绝对测距的大量程和线性测量性能.     

Two-photon induced photorefraction in undoped lithium tantalate crystals with different compositions

Two-photon interband photorefraction in undoped lithium tantalate crystals with composition ranging from 47.95 to 49.6 mol% of lithium oxide was demonstrated at the wavelength of 532 nm. The photorefractive properties were examined with holographic method. Two-photon holograms were recorded with high holographic sensitivity, large refractive index change, and fast hologram writing time. Permanent changes of the refractive index have been obtained. These holograms can be read nondestructively at the wavelength of 660 nm using heterodyne method. Holographic characteristics strongly depend on composition.     

Investigation of thermal influence on the bandgap properties of liquid-crystal photonic crystal fibers

We have analyzed the thermal influence on the bandgap properties of liquid-crystal photonic crystal fibers. The bandgap parameters which affect the transmission conditions have been investigated. It is observed that the photonic bandgap can be thermally tuned, i.e. the red or blue shift of the bandgap results from the temperature dependence of the refractive index of the liquid crystal. For the planar alignment of liquid-crystal filled cladding, the ordinary refractive index plays a major role in determining the bandgap properties; the extraordinary refractive index comes into influence while the ordinary refractive index is relatively constant of temperature. The analyses agree well with the experiments results.     

Dispersion characteristics of complex refractive-index planar slab optical waveguide by using finite element method

In this paper, finite element method (FEM) mode analyses of planar slab optical waveguide having complicated refractive index profile are presented. We try to estimate the dispersion graph, mode cut-off condition, group delay and waveguide dispersion for the case of α-power and chirped-type refractive index profile. In order to obtain the more accurate result, we have derived the higher-order polynomial, which establishes the suitable relationship between b and V for different profile of optical waveguide. On the basis of the derived polynomials, the waveguide dispersion is analyzed for different type of refractive index profile waveguide. Our study shows that the waveguide dispersion can be substantially reduced when we deployed the optical waveguide having linearly chirped-type refractive index profile. Earlier too, the arbitrary refractive index profile has been analyzed but to the best of our knowledge chirped-type refractive index profile has not been analyzed till date for the case of planar slab optical waveguide.     

Theoretical and Experimental Study of Long-Period Grating Refractive Index Sensor

Abstract

This article presents the theoretical and experimental investigation of the response of long-period gratings as a refractive index sensor. Cladding modes are calculated, and results are compared with Optigrating 4.2.2 (Optiwave Systems Inc., Ottawa, Canada). The response has been checked for refractive indices ranging from 1 to 1.458. Theoretically simulated results are in accordance with the experimental results. It was found that the software package calculated values correctly up to the seventh decimal point. The ambient refractive index response of a long-period grating over a much wider index range has been modeled for values both less and more than the cladding refractive index.     

Study and investigation of long period grating as refractive index sensor

In this paper, we have investigated the response of long period grating (LPG) as refractive index sensor. The response has been studied for refractive index variation ranging from 1 to 1.45. In this work, we found that the sensing mechanism is based on two different aspects. First is the change of coupling power from the guided core mode to other co-propagating cladding modes and second is the wavelength shift of the peak resonant wavelengths from their original positions due the change of refractive index of the environmental (external) medium surrounding the cladding of the grating.     

Highly sensitive photonic crystal fiber biosensor based on titanium nitride

A highly sensitive surface plasmon resonance photonic crystal fiber (PCF) biosensor based on Titanium Nitride (TiN) as a new alternative plasmonic material is proposed and analyzed. The TiN has high stability, high conductivity, and corrosion resistance which make it an ideal material for nanofabrication. The suggested biosensor is analyzed by full vectorial finite element method with perfectly matched layer as boundary conditions. In this paper, the biosensor geometrical parameters are studied to achieve high sensitivity for both polarized modes. A refractive index sensitivity of 7700 and 3600 nm/RIU for quasi-transverse electric and quasi transverse magnetic modes, respectively, are obtained. Additionally, the reported biosensor could be used for detecting an unknown analyte refractive index ranging from 1.32 to 1.34 with a high linearity. Further, the proposed biosensor structure is easy for fabrication using standard PCF fabrication current technologies.     

高功率微波在电离层中传播的折射率研究

 高功率微波在电离层中的传播特性主要由其折射率的变化决定，而高功率微波的大气折射率与相应传输层面的电子浓度有关。结合电离层电子浓度分布模型对电子浓度和大气折射率进行了数值模拟，对电离层折射率以及折射率垂直梯度相对于高度的变化特性进行了分析。结合射线描迹法对高功率微波波束传播高度、仰角和距离进行了修正，并在低功率微波下进行实验验证，证实修正值更接近实际值。     

Slot-waveguide biochemical sensor

We report an experimental demonstration of an integrated biochemical sensor based on a slot-waveguide microring resonator. The microresonator is fabricated on a Si3N4-SiO2 platform and operates at a wavelength of 1.3 microm. The transmission spectrum of the sensor is measured with different ambient refractive indices ranging from n=1.33 to 1.42. A linear shift of the resonant wavelength with increasing ambient refractive index of 212 nm/refractive index units (RIU) is observed. The sensor detects a minimal refractive index variation of 2x10(-4) RIU.     

基于传输矩阵法讨论光疏介质表面的全反射

探究了光在光密介质与超薄光疏介质界面处的全反射,通过在光密介质中嵌入一光疏介质薄层,利用传输矩阵法,定量地分析了入射角度以及光疏介质的厚度对反射率的影响.数值模拟结果表明,当光疏介质的厚度小于约一个波长时,即使入射角大于全反射的临界角,反射率也不一定会达到1,也就是说,光学隧道效应将会出现.     

On the Sign of the Refractive Index for Metamaterials

Russian Physics Journal - The concept of the negative refractive index with application to doubly negative metamaterials is critically analyzed. The positive value of the refractive index is...     

Investigation on an evanescent wave fiber-optic absorption sensor based on fiber loop cavity ring-down spectroscopy

An improved ring-down measurement principle for optical waveguides is presented. Fiber loop ring-down spectroscopy allows for measurement of minute optical losses in high-finesse fiber-optic cavities and immunity to the fluctuation of laser source. The evanescent wave absorption losses dependent on the absorption and the refractive index of ambient solution have been theoretically analyzed. The complex refractive index is introduced into our model and extinction coefficient can be calculated accurately through finite element analysis by setting the boundaries of the fiber and the ambient conditions. Using this method, the refractive index of environment can be taken into consideration. Our principle is validated by the highly-sensitive measurement of evanescent wave absorption loss. By chemically processing the surface of sensing segment along an extending ring-down cavity, the concentration of small volume Diethyl Sulphoxide solution where the etched fiber immersed into has been successfully measured and discussed.     

Finite difference scheme for planar waveguides with arbitrary index profiles and its implementation for anisotropic waveguides with a diagonal permitivity tensor

A finite difference scheme with a uniform mesh for planar waveguides with arbitrary refractive index profiles that takes full account of any smooth index variation and index discontinuity is derived for TE and TM-polarized waves. Discretizations that lead to a second-order error in the effective indices are given for TE and TM polarizations. At the computational boundaries, transparent boundary conditions are used. The scheme was implemented for anisotropic waveguides with a diagonal permitivity tensor and examined by using samples with various refractive index profiles, ranging from simple step- and graded-index up to complicated refractive index profile structures composed of either isotropic or anisotropic materials. For simple cases where the results of other methods are available in the literature, the proposed scheme shows very good agreement.     

用光纤白光干涉技术测量晶体的弹光系数

运用折射率椭球分析晶体的弹光效应,给出了三方晶系沿光轴方向的应力与折射率的变化关系.针对晶体的各向异性和折射率随应力变化很小的因素,利用白光干涉技术空间分辨率高的特点,将白光干涉技术拓展到研究各向异性材料的光学性质. 并对测量群折射率的光纤迈克尔逊白光干涉技术进行了改进.采用光栅位移传感器和全保偏光纤提高反射扫描镜的位移准确度.通过测量石英晶体在不同外力下折射率的变化情况,确定了晶体的弹光系数. 石英晶体的弹光系数P33和P13分别为0.110和0.279,其准确度达到0.001.     

层状GRIN板折射率分布的自动测量

采用溶液 凝胶扩散共聚法成功地合成了二元体系的甲基烯酸苄酯 甲基烯酸甲酯 (BZMA MMA)层状梯度折射率板 ,折射率分布是其主要性能指标。给出了一种测量该制品折射率分布的简便实验装置和自动实现方法。该测量方法基于激光干涉的原理 ,由计算机自动跟踪干涉条纹的移动来计算梯度折射率材料的折射率分布。实验表明 ,该方法简单易行 ,具有较高的折射率测量精度 ,为科学评价自研制梯度折射率材料的性能提供了保证     

Optical and structural parameters of the ZnO thin film grown by pulsed filtered cathodic vacuum arc deposition

Transparent conductive ZnO film was deposited on glass substrate by pulsed filtered cathodic vacuum arc deposition (PFCVAD). Optical parameters such as absorption coefficient α, the refractive index n, energy band gap E_g and dielectric constants have been determined using different methods. Kramers-Kronig and dispersion relations were employed to determine the complex refractive index and dielectric constants using reflection data in the ultraviolet-visible-near infrared regions. The spectra of the dielectric coefficient were used to calculate the energy band gap and the value was 3.24 eV. The experimental energy band gap was found to be 3.22 eV for 357 nm thick ZnO thin film. The envelope method was also used to calculate the refractive index and the data were consistent with K-K relation results. The structure of the film was analyzed with an x-ray diffractometer and the film was polycrystalline in nature with preferred (002) orientation.     

γ辐射对光纤波导电磁场分布的影响

开展了光纤波导中的电磁场传输理论分析,得到了光纤折射率变化对波导中电磁场分布的影响规律,建立了块状融石英材料及光纤光栅在60Co 辐射作用下折射率变化的测量系统,开展了折射率随辐射剂量变化及光纤模场测量实验。结果表明:光纤的折射率随辐射剂量的增加而增大,折射率的变化会引起波导中传输模式的场强分布变化,从而导致光纤的辐射感生波导损耗;在一定的辐射剂量范围（0～2000 Gy）内,光纤仍满足弱导边界条件,能够维持对传输模式的约束能力。     

Deposition of coatings on long-period fiber gratings: tunnel effect analogy

The sensitivity of Long-period fiber gratings (LPFGs), coated with high-refractive-index thin film overlays, to the refractive index and the thickness of the overlay, and to the ambient refractive index, can be enhanced with a design based on a two-overlay coating of an LPFG. The first overlay of lower refractive index than the cladding affects the guidance of a cladding mode in the second overlay of higher refractive index than the cladding. This causes a more abrupt cladding modal redistribution than with the deposition of a unique high-refractive-index overlay. The phenomenon is analyzed with a method based on a vectorial analysis of modes and the application of coupled mode theory.